Iinterpretação conjunta de dados de GPR e medidas de permeabilidade sobre um análogo de reservatório siliciclástico falhado na bacia de Tucano, no NE do Brasil

It is presented an integrated geophysical investigation of the spatial distribution of faults and deformation bands (DB´s) in a faulted siliciclastic reservoir analogue, located in Tucano Basin, Bahia State, northeastern Brazil. Ground Penetrating Radar (GPR) and permeability measurements allowed the analysis of the influence of DB´s in the rock permeability and porosity. GPR data were processed using a suitable flow parametrization in order to highlight discontinuities in sedimentary layers. The obtained images allowed the subsurface detection of DB´s presenting displacements greater that 10 cm. A good correlation was verified between DB´s detected by GPR and those observed in surface, the latter identified using conventional structural methods. After some adaptations in the minipermeameter in order to increase measurement precision, two approaches to measure permeabilities were tested: in situ and in collected cores. The former approach provided better results than the latter and consisted of scratching the outcrop surface, followed by direct measurements on outcrop rocks. The measured permeability profiles allowed to characterize the spatial transition from DB´s to undeformed rock; variation of up to three orders of magnitude were detected. The permeability profiles also presented quasi-periodic patterns, associated with textural and granulometric changes, possibly associated to depositional cycles. Integrated interpretation of the geological, geophysical and core data, provided the subsurface identification of an increase in the DB´s number associated with a sedimentary layer presenting granulometric decrease at depths greater than 8 m. An associated sharp decrease in permeability was also measured in cores from boreholes. The obtained results reveal that radagrams, besides providing high resolution images, allowing the detection of small structures (> 10 cm), also presented a correlation with the permeability data. In this way, GPR data may be used to build upscaling laws, bridging the gap between outcrop and seismic data sets, which may result in better models for faulted reservoirs

Diagênese e proveniência dos arenitos da tectonossequência Rifte na bacias do Rio do Peixe Araripe, NE do Brasil

This thesis presents diagenetic and provenance studies of sandstones belonging to the Rift Tectonosequence of the Rio do Peixe and Araripe basins. These basins are located in the interior of Northeast Brazil aligned along the Trend-Cariri Potiguar. Their origin is related to the Early Cretaceous rifting event. In terms of lithostratigraphy, the studied section corresponds to the Antenor Navarro, Sousa and Rio Piranhas formations of the Rio do Peixe Basin, and the Missão Velha and Abaiara formations of the Araripe Basin, outcropping in the central-west Cariri Valley. A facies analysis was performed and identified nine distinct sedimentary facies for the Rio de Peixe Basin and ten sedimentary facies for the Araripe Basin, individualized according to the different rock types and their sedimentary structures. These facies associations to led paleoenvironments interpretations and their vertical succession allowed understanding the evolution of the depositional setting during the cronostratigraphic interval studied in these basins. Based on petrographic and diagenetic studies it was possible to characterize the texture and mineralogy of these sandstones, identifying their diagenetic stage and the grain framework provenance. The petrographic study allowed to classify the lithotypes studied in both basins as quartzarenites. Such quartzarenites, in general, are rich in quartz, feldspar and lithic fragment grains, and at accessory levels tourmaline, sphene, zircon, epidote and other mineralogy. The diagenetic history of the studied rocks proved to be very complex, being characterized by a variety mineral of phases that succeeded each other during the eo, meso and telodiagenetic stages. According to the studied formation and the textural and compositional aspects of the rocks, some processes were more or less active, while others were even absent. The eodiagenetic stage is marked by mechanical infiltration of clays and early mechanical compactional processes. The mesodiagenetic phase is characterized by continuity of the mechanical compaction and the beggining of chemical compaction, with quartz and feldspar overgrowths, precipitation of kaolinite, alteration of framework grains to chlorite and illite, and finally, precipitation of opaque minerals. The telodiagenetic stage is represented by the oxidation of some grains, matrix and cements. For the provenance analysis of the studied sandstones were used ternary diagrams whose vertices correspond to the percentage of quartz, feldspar and lithic fragments. This study allowed identifies the source area of these rocks as continental blocks. It was also possible, based on the chemical stability and mineralogical maturity of the rocks, recognize that the Antenor Navarro Formation of the Rio do Peixe Basin, and the upper section of the Missão Velha Formation of Araripe Basin have less maturity and stability when compared with the other studied formations

Interpretação sísmica e análise de atributos - área do levantamento sísmico 3D de siririzinho (Bacia Sergipe-Alagoas, NE do Brasil)

The main objective of the present thesis was the seismic interpretation and seismic attribute analysis of the 3D seismic data from the Siririzinho high, located in the Sergipe Sub-basin (southern portion of Sergipe-Alagoas Basin). This study has enabled a better understanding of the stratigraphy and structure that the Siririzinho high experienced during its development. In a first analysis, we used two types of filters: the dip-steered median filter, was used to remove random noise and increase the lateral continuity of reflections, and fault-enhancement filter was applied to enhance the reflection discontinuities. After this filtering step similarity and curvature attributes were applied in order to identify and enhance the distribution of faults and fractures. The use of attributes and filtering greatly contributed to the identification and enhancement of continuity of faults. Besides the application of typical attributes (similarity and curvature) neural network and fingerprint techniques were also used, which generate meta-attributes, also aiming to highlight the faults; however, the results were not satisfactory. In a subsequent step, well log and seismic data analysis were performed, which allowed the understanding of the distribution and arrangement of sequences that occur in the Siririzinho high, as well as an understanding of how these units are affected by main structures in the region. The Siririzinho high comprises an elongated structure elongated in the NS direction, capped by four seismo-sequences (informally named, from bottom to top, the sequences I to IV, plus the top of the basement). It was possible to recognize the main NS-oriented faults, which especially affect the sequences I and II, and faults oriented NE-SW, that reach the younger sequences, III and IV. Finally, with the interpretation of seismic horizons corresponding to each of these sequences, it was possible to define a better understanding of geometry, deposition and structural relations in the area.

Caracterização das assembléias de peixes de riachos de cabeceira no período chuvoso na bacia do rio Cachoeira (SE da Bahia, NE do Brasil)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise de sedimentos associados à atividade de perfuração na plataforma continental externa, Bacia Potiguar - Brasil

This study was developed in an area located on the outer shelf in the Potiguar Basin, Brazilian equatorial margin; this tropical shelf represents a modern, highly dynamic mixed carbonate-siliciclastic system. Field sampling was carried out during 3 cruises surrounding a shallow-water exploratory well to compare sediment properties of the seafloor, including grainsize, texture, mineral composition, carbonate content, and organic matter. Cruise 1 (C1) was carried prior to drilling, while Cruise 2(C2) and 3 (C3) respectivelly 3 and 12 months after drilling. The sample grid used had 16 stations located along 4 radials from 50 m the well up to a distance of 500 m. Sediments were analyzed in the first 0-2 cm, and 0-10 cm layers. The results show that sedimentary cover around the well is poor to very poorly sorted, with the particle size predominantly in the medium to coarse sand fraction, followed by gravel and mud. The content of calcium carbonate is greater than 96%, associated to bioclastic sediments, and the content of organic matter is less than 12%. Only minor sedimentological variations occured in the area affected by drilling operations. Mainly observed during the second cruise, in terms of a change in grain size distribution associated to an increase in siliciclastic content, This impact occurred in the most surficial sediment (0-2 cm), in the radial closest to the well (50 m), and could suggest the effects of drilling. However, in the third cruise, one year after drilling, the sediments return to show the same characteristics as in the first cruise. These results show no significant sedimentological variations due to drilling activity, and indicate that ocean dynamics in this area was high enough to recover the environment original characteristics.

Análise de sedimentos associados à atividade de perfuração na plataforma continental externa, Bacia Potiguar - Brasil

This study was developed in an area located on the outer shelf in the Potiguar Basin, Brazilian equatorial margin; this tropical shelf represents a modern, highly dynamic mixed carbonate-siliciclastic system. Field sampling was carried out during 3 cruises surrounding a shallow-water exploratory well to compare sediment properties of the seafloor, including grainsize, texture, mineral composition, carbonate content, and organic matter. Cruise 1 (C1) was carried prior to drilling, while Cruise 2(C2) and 3 (C3) respectivelly 3 and 12 months after drilling. The sample grid used had 16 stations located along 4 radials from 50 m the well up to a distance of 500 m. Sediments were analyzed in the first 0-2 cm, and 0-10 cm layers. The results show that sedimentary cover around the well is poor to very poorly sorted, with the particle size predominantly in the medium to coarse sand fraction, followed by gravel and mud. The content of calcium carbonate is greater than 96%, associated to bioclastic sediments, and the content of organic matter is less than 12%. Only minor sedimentological variations occured in the area affected by drilling operations. Mainly observed during the second cruise, in terms of a change in grain size distribution associated to an increase in siliciclastic content, This impact occurred in the most surficial sediment (0-2 cm), in the radial closest to the well (50 m), and could suggest the effects of drilling. However, in the third cruise, one year after drilling, the sediments return to show the same characteristics as in the first cruise. These results show no significant sedimentological variations due to drilling activity, and indicate that ocean dynamics in this area was high enough to recover the environment original characteristics.

Evolução estratigráfica da sequência neocarbonífera-eotriássica da Bacia do Parnaíba, NE do Brasil

The Parnaíba Basin consists in an intracratonic basin whose sucession of rocks is arranged in five supersequences. The Upper Carboniferous-Lower Triassic Sequence represents the third major sedimentary cycle and corresponds to Balsas Group, which is divided into four units: Piauí Formation, Pedra de Fogo Formation, Motuca Formation and Sambaíba Formation, from base to top. Different interpretations have been made by several authors in recent decades to interpreted the depositional system and environments related to each unit that belongs to this sequence. In general way, it is described as a thick pack of siliciclastic sediments deposited under complex conditions, varying from clastic/evaporitic shallow marine to lacustrine and desert environment. Aiming to clarify the sedimentary sequence evolution, this work underwent a stratigraphic analysis of the Upper Carboniferous-Lower Triassic deposits by applying modern concepts of the sequence stratigraphy based on well and seismic database. Three main depositional sequences of higher frequency were identified in each well analyzed. The sequence 1 corresponds to rocks initially deposited by a fluvial system with braided channel characteristics which evolved to shallow marine with coastal sabkha conditions related to a transgressive stage, that later evolved to a deltaic system. The Sequence 2 corresponds to rocks deposited in a lacustrine/desert environment associated with sabkha generated during a period of increased aridity in which the area occupied by the Parnaíba Basin had been suffering. The registration of a major regressive phase is shown in Sequence 2 which evolved to a dominantly desert environment recorded in Sequence 3. Seismic stratigraphy analyses allow to define a series of stratigraphic surfaces and related genetic units, as well as to infer its lateral expression. Seismic facies associated with such sequences are dominantly parallel and sub-parallel, with good lateral continuity, suggesting the sedimentary rate was relatively constant during deposition.

Evolução estratigráfica da sequência neocarbonífera-eotriássica da Bacia do Parnaíba, NE do Brasil

The Parnaíba Basin consists in an intracratonic basin whose sucession of rocks is arranged in five supersequences. The Upper Carboniferous-Lower Triassic Sequence represents the third major sedimentary cycle and corresponds to Balsas Group, which is divided into four units: Piauí Formation, Pedra de Fogo Formation, Motuca Formation and Sambaíba Formation, from base to top. Different interpretations have been made by several authors in recent decades to interpreted the depositional system and environments related to each unit that belongs to this sequence. In general way, it is described as a thick pack of siliciclastic sediments deposited under complex conditions, varying from clastic/evaporitic shallow marine to lacustrine and desert environment. Aiming to clarify the sedimentary sequence evolution, this work underwent a stratigraphic analysis of the Upper Carboniferous-Lower Triassic deposits by applying modern concepts of the sequence stratigraphy based on well and seismic database. Three main depositional sequences of higher frequency were identified in each well analyzed. The sequence 1 corresponds to rocks initially deposited by a fluvial system with braided channel characteristics which evolved to shallow marine with coastal sabkha conditions related to a transgressive stage, that later evolved to a deltaic system. The Sequence 2 corresponds to rocks deposited in a lacustrine/desert environment associated with sabkha generated during a period of increased aridity in which the area occupied by the Parnaíba Basin had been suffering. The registration of a major regressive phase is shown in Sequence 2 which evolved to a dominantly desert environment recorded in Sequence 3. Seismic stratigraphy analyses allow to define a series of stratigraphic surfaces and related genetic units, as well as to infer its lateral expression. Seismic facies associated with such sequences are dominantly parallel and sub-parallel, with good lateral continuity, suggesting the sedimentary rate was relatively constant during deposition.

Estruturas tectônicas cenozóicas na porção leste da Bacia Potiguar - RN

This thesis encompasses the integration of geological, geophysical, and seismological data in the east part of the Potiguar basin, northeastern Brazil. The northeastern region is located in South American passive margin, which exhibits important areas that present neotectonic activity. The definition of the chronology of events, geometry of structures generated by these events, and definition of which structures have been reactivated is a necessary task in the region. The aims of this thesis are the following: (1) to identify the geometry and kinematics of neotectonic faults in the east part of the Potiguar basin; (2) to date the tectonic events related to these structures and related them to paleoseismicity in the region; (3) to present evolutional models that could explain evolution of Neogene structures; (4) and to investigate the origin of the reactivation process, mainly the type of related structure associated with faulting. The main type of data used comprised structural field data, well and resistivity data, remote sensing imagery, chronology of sediments, morphotectonic analysis, x-ray analysis, seismological and aeromagnetic data. Paleostress analysis indicates that at least two tectonic stress fields occurred in the study area: NSoriented compression and EW-oriented extension from the late Campanian to the early Miocene and EW-oriented compression and NS-oriented extension from the early Miocene to the Holocene. These stress fields reactivated NE-SW- and NW-SE-trending faults. Both set of faults exhibit right-lateral strike-slip kinematics, associated with a minor normal component. It was possible to determine the en echelon geometry of the Samambaia fault, which is ~63 km long, 13 km deep, presents NE-SW trend and strong dip to NW. Sedimentfilled faults in granite rocks yielded Optically Stimulated Luminescence (OSL) and Single-Aliquot Regeneration (SAR) ages at 8.000 - 9.000, 11.000 - 15.000, 16.000 - 24.000, 37.000 - 45.500, 53.609 - 67.959 e 83.000 - 84.000 yr BP. The analysis of the ductile fabric in the João Câmara area indicate that the regional foliation is NE-SW-oriented (032o - 042o), which coincides with the orientation of the epicenters and Si-rich veins. The collective evidence points to reactivation of preexisting structures. Paleoseismological data suggest paleoseismic activity much higher than the one indicated by the short historical and instrumental record

Análises estratigráfica e estrutural da Seção Rifte (Valanginiano ao Barremiano) na área do levantamento sísmico 3D de baixo vermelho, Bacia Potiguar emersa

Baixo Vermelho area, situated on the northern portion of Umbuzeiro Graben (onshore Potiguar Basin), represents a typical example of a rift basin, characterized, in subsurface, by the sedimentary rift sequence, correlated to Pendência Formation (Valanginian-Barremian), and by the Carnaubais fault system. In this context, two main goals, the stratigraphic and the structural analysis, had guided the research. For this purpose, it was used the 3D seismic volume and eight wells located in the study area and adjacencies. The stratigraphic analysis of the Valanginian-Barremian interval was carried through in two distinct phases, 1D and 2D, in which the basic concepts of the sequence stratigraphy had been adapted. In these phases, the individual analysis of each well and the correlation between them, allowed to recognize the main lithofacies, to interpret the effective depositional systems and to identify the genetic units and key-surfaces of chronostratigraphic character. The analyzed lithofacies are represented predominantly by conglomerates, sandstones, siltites and shales, with carbonate rocks and marls occurring subordinately. According to these lithofacies associations, it is possible to interpret the following depositional systems: alluvial fan, fluvio-deltaic and lacustrine depositional systems. The alluvial fan system is mainly composed by conglomerates deposits, which had developed, preferentially in the south portion of the area, being directly associated to Carnaubais fault system. The fluvial-deltaic system, in turn, was mainly developed in the northwest portion of the area, at the flexural edge, being characterized by coarse sandstones with shales and siltites intercalated. On the other hand, the lacustrine system, the most dominant one in the study area, is formed mainly by shales that could occur intercalated with thin layers of fine to very fine sandstones, interpreted as turbidite deposits. The recognized sequence stratigraphy units in the wells are represented by parasequence sets, systems tracts and depositional sequences. The parasequence sets, which are progradational or retrogradational, had been grouped and related to the systems tracts. The predominance of the progradation parasequence sets (general trend with coarsening-upward) characterizes the Regressive Systems Tract, while the occurrence, more frequently, of the retrogradation parasequence sets (general trend with finning-upward) represents the Transgressive System Tract. In the seismic stratigraphic analysis, the lithofacies described in the wells had been related to chaotic, progradational and parallel/subparallel seismic facies, which are associated, frequently, to the alluvial fans, fluvial-deltaic and lacustrine depositional systems, respectively. In this analysis, it was possible to recognize fifteen seismic horizons that correspond to sequence boundaries and to maximum flooding surfaces, which separates Transgressive to Regressive systems tracts. The recognition of transgressive-regressive cycles allowed to identify nine, possibly, 3a order deposicional sequences, related to the tectonic-sedimentary cycles. The structural analysis, in turn, was done at Baixo Vermelho seismic volume, which shows, clearly, the structural complexity printed in the area, mainly related to Carnaubais fault system, acting as an important fault system of the rift edge. This fault system is characterized by a main arrangement of normal faults with trend NE-SO, where Carnaubais Fault represents the maximum expression of these lineations. Carnaubais Fault corresponds to a fault with typically listric geometry, with general trend N70°E, dipping to northwest. It is observed, throughout all the seismic volume, with variations in its surface, which had conditioned, in its evolutive stages, the formation of innumerable structural features that normally are identified in Pendencia Formation. In this unit, part of these features is related to the formation of longitudinal foldings (rollover structures and distentional folding associated), originated by the displacement of the main fault plan, propitiating variations in geometry and thickness of the adjacent layers, which had been deposited at the same time. Other structural features are related to the secondary faultings, which could be synthetic or antithetic to Carnaubais Fault. In a general way, these faults have limited lateral continuity, with listric planar format and, apparently, they play the role of the accomodation of the distentional deformation printed in the area. Thus, the interaction between the stratigraphic and structural analysis, based on an excellent quality of the used data, allowed to get one better agreement on the tectonicsedimentary evolution of the Valanginian-Barremian interval (Pendência Formation) in the studied area

Estudo geológico e geofísico da falha de carnaubais, Bacia Potiguar-RN, e implicações neotectônicas

The segment of Carnaubais Fault located in the southeasthern portion of Guamaré Graben (Potiguar Basin) was studied. Several structures were detected and some of them strongly suggest that the last movements in Carnaubais Fault are of Neotectonic age. The study comprises an integrated interpretation of geologic, geomorphologic and geophysical data (gravimetry, magnetometry, resistivity, and self potential methods). According to the size of the studied areas, two approaches were used in this research. The first approach is of a regional nature and was conducted in an area, hereafter named Regional Area, having approximately 6,000 km2 and localized in the northern portion of Rio Grande do Norte state, around Macau city. The second approach comprises detailled studies of two small areas inside the Regional Area: the Camurupim and São Bento areas. Gravimetric and topographic data were used in the Regional Area. A separation into regional and residual components were conducted both on gravimetric and topographic data. The interpretation of the residual component of the gravimetric data allows a precise mapping of the borders of the Guamaré Graben. The regional component features of the topographic data are controlled by the pair of conjugate faults composed by the Carnaubais Fault (NE direction) and the Afonso Bezerra Fault (NW direction). On the other hand, the residual component of the topographic data shows that river valleis of NW direction are sharply interrupted where they intersect Carnaubais Fault. This fact is interpreted as an evidency that the last significant moviments occured in the Carnaubais Fault. Geologic, geomorphologic and geophysical data (magnetometry, resistivity, and self potential methods) were used in the Camurupim Area. The geologic mapping allows to identify five lithophacies unities. The first two unities (from base to top) were interpreted as composing a marine (or transitional) depositional sequency while the other were interpreted is composing a continental depositional sequence. The two sequences are clearly separated of an erosional discordance. The unities grouped in the marine sequence are composed by calcarenites (Unity A) and mudstones (Unity B). Unity A was deposited in a shalow plataform while Unity B, in a tidal flat. The unities grouped in the continental sequence are composed of conglomerate (Unity C) and sandstones (Unities D and E). Unities C and D are fluvial deposits while unity E is an eolian deposit. Unities A and B can be stratigraphycally correlated with Guamaré Formation. Unities C and D present three possible correlations. They may be correlated with Tibau Formation; or with Barreiras Formation; or with a clastic sediment deposit, commonly found in some rivers of Rio Grande do Norte state, and statigraphycally positioned above Barreiras Formation. Based on the decrease of the grain sizes from base to top both on unities C and D, it is proposed that these unities are correlated with the clastic sediment above mentioned. In this case, these unities would have, at least, Pleistocenic age. Finally, it is proposed that Unity E represent an eolian deposit that sufferred recent changes (at least in the Quaternary). The integrated interpretation of hydrographic, morphologic and geophysical data from Camurupim Area shows that Carnaubais Fault is locally composed by a system of several paralel subvertical faults. The fault presenting the larger vertical slip controls the valley of Camurupim river and separates the area in two blocks; in the nothern block the top of the Jandaira limestone is deeper than in the southern block. In addition, at least one of the faults in the northern block is cutting the whole sedimentary section. Because unities C , D, and/or E may be of Quaternary age, tectonic moviments possibly occured in Carnaubais Fault during this period. Detailled geologic mapping were conducted in beachrocks found in São Bento Area. This area is located at the intersection of the coast line with the Carnaubais Fault. The detected structures in the beachrocks are very similar to those caused by fragile deformations. The structures mapped in the beachrocks are consistent with a stress field with maximun compressional stress in E-W direction and extensional stress in the N-S direction. Since the Carnaubais Fault has a NE direction, it is optimally positioned to suffer tectonic movements under the action of such stress field. In addition, the shape of the coastal line appear to be controlled by the Carnaubais Fault. Furthemore, the observed structures in Camurupim Área are consistent with this stress field. These facts are interpreted as evidences that Carnaubais Fault and beachrocks suffered coupled tectonic movements. These moviments are of Neotectonic age because the beachrocks present ages less than 16,000 years

Expressão em superfície do sistema de falhas Poço Verde-caraúbas, Bacia Potiguar

The structural knowledge of the western portion of the Potiguar Basin is still in its infancy, especially these related to NW-trending fault systems. This paper analyzes the Poço Verde-Caraúbas Fault System, which was initially recognized in subsurface. The activities involved in this study correspond to remote-sensing analysis and, in particular, to the geometric and kinematic analysis of post-rift sequences of the basin. In addition, the study aimed to determine the stress fields operating in the area. The studies were carried out in an area of 1,000 km², located in the western portion of Potiguar Basin along the Poço Verde-Caraúbas Fault System, Rio Grande do Norte State. The remote sensing imagery indicates a predominance of NW-SE-trending lineaments, consistent with the fault system under study, followed by the NE-SW, N-S and E-W directions. The tectonic structures mapped were analyzed only in outcrops of the Jandaíra Formantion. They are joints (filled or not) in all directions, but with predominance of the NW-trending joints. Faults are usually N-S-trending normal faults and NW-SE and NE-SW-trending strike-slip faults. Geodynamic analysis identified two tectonic stress fields: the first field, "Field 1" is represented by an N-S-trending horizontal compression and E-W-trending horizontal extension. This field affected the Potiguar Basin at least until the Miocene. The second field, "Field 2", is represented by an E-W-trending horizontal compression and N-S-trending horizontal extension. This is the present-day stress field and has affected the Potiguar basin since the Pliocene

Estimativa da profundidade do embasamento na bacia potiguar usando inversão gravimétrica

The gravity inversion method is a mathematic process that can be used to estimate the basement relief of a sedimentary basin. However, the inverse problem in potential-field methods has neither a unique nor a stable solution, so additional information (other than gravity measurements) must be supplied by the interpreter to transform this problem into a well-posed one. This dissertation presents the application of a gravity inversion method to estimate the basement relief of the onshore Potiguar Basin. The density contrast between sediments and basament is assumed to be known and constant. The proposed methodology consists of discretizing the sedimentary layer into a grid of rectangular juxtaposed prisms whose thicknesses correspond to the depth to basement which is the parameter to be estimated. To stabilize the inversion I introduce constraints in accordance with the known geologic information. The method minimizes an objective function of the model that requires not only the model to be smooth and close to the seismic-derived model, which is used as a reference model, but also to honor well-log constraints. The latter are introduced through the use of logarithmic barrier terms in the objective function. The inversion process was applied in order to simulate different phases during the exploration development of a basin. The methodology consisted in applying the gravity inversion in distinct scenarios: the first one used only gravity data and a plain reference model; the second scenario was divided in two cases, we incorporated either borehole logs information or seismic model into the process. Finally I incorporated the basement depth generated by seismic interpretation into the inversion as a reference model and imposed depth constraint from boreholes using the primal logarithmic barrier method. As a result, the estimation of the basement relief in every scenario has satisfactorily reproduced the basin framework, and the incorporation of the constraints led to improve depth basement definition. The joint use of surface gravity data, seismic imaging and borehole logging information makes the process more robust and allows an improvement in the estimate, providing a result closer to the actual basement relief. In addition, I would like to remark that the result obtained in the first scenario already has provided a very coherent basement relief when compared to the known basin framework. This is significant information, when comparing the differences in the costs and environment impact related to gravimetric and seismic surveys and also the well drillings

Indicadores do nível relativo do mar e evolução costeira durante o holoceno tardio no litoral oeste do Ceará, NE do Brasil

In the coastal region of Ceará, between the municipalities of Acaraú and Itapipoca, thirteen sites were identified containing indicators of relative sea level, six of these being dated by optically stimulated luminescence (OSL) and radiocarbon. Ages obtained supports that were formed prograding beaches in the study area. In the eastern portion, beaches in coastal plain deposits occur while a system lagoon/barrier paleomangrove occurs in the western portion of the study area. In both cases the coastal deposits prograde from east to west. Higher sea levels were identified between the current: (a) 3.110-2.830 cal. yr. BP; (b) 1.830 yr. BP (OSL) - 1.490 cal. yr. BP; (c) between 1.240-1.060 cal. yr. BP; (d) 845-715 yr. BP (OSL). Since then the sea level suffered by lowering the current level. Variations in sea level are interpreted as responses to changes in the pattern of marine circulation and do not exclude possible tectonic disturbances in the basin of the continental margin. The indicators of relative sea level west coast of Ceará present differently from other curves constructed in the coastal northeast, suggesting that local factors mentioned above contributed to sea level fluctuations.

Caracterização morfológica-sedimentar do vale inciso Apodi-Mossoró e plataforma continental adjacente - Bacia Potiguar Offshore

Systems of incised valleys have been studied in different continental shelves, including the Brazilian continental margin. The interest to characterize this feature is given by the information that it can provide variations on sea level, as well as the ability to host economically significant quantities of hydrocarbons in reservoirs located in deposits filling of the incised valleys. This thesis has the overall objective to characterize the morphology and sedimentary cover of the incised valley Apodi-Mossoró, located in the Northern Continental shelf of Rio Grande do Norte state, adjacent to Areia Branca city. The methodology included the integration of satellite imagery, bathymetric data, sedimentological data, shallow seismic, and the identification of foraminifera. The results indicate that the ApodiMossró incised valley is currently formed by two channels, shallow channel and deep channel, which have distinct morphological and sedimentological characteristics. The deep channel has connection with one of the heads of the Apodi Canyon, located in the slope area. The acquisition, processing and interpretation of shallow seismic data allowed the recognition of the depositional surface, erosional surface, discordance, and sismofaceis. The erosional surface mapped from shallow seismic sections is possibly a indicative of an ancient surface of valley incision, where it would probably be associated with the limit Pleistocene/Holocene. Different sismofaceis were identified and reflect the rise in sea level with standards sometimes agradacional, sometimes progradational. The thickness of sediments on this surface was estimated at a maximum of 22m thick in the central portion of the incised valley. Statistically, there are differences between the adjacent continental shelf and channels, and between these channels, for the content of calcium carbonate, organic matter, sand and mud perceptual, except for the gravel grain size. The analysis of living and dead foraminifera showed the presence of fifty species distributed in regards to morphology, depth and type of sediment. Four type of seismic echocharacteres were identified and mapped, as well as their bedforms, indicating different sedimentary processes along the incised valley. The integration of results suggests an activation of the Apodi-Mossoró incised valley in the Late Pleistocene.