Estudo da viabilidade técnica para a Bolívia de painéis de gesso reforçados com fibra de vidro para paredes internas não portantes

Na construção civil, nos países em desenvolvimento como a Bolívia, continua-se usando técnicas e materiais na execução de paredes, similar a décadas passadas. Os painéis de gesso reforçados com fibra de vidro são uma alternativa de simplificação e agilização na execução das paredes internas não portantes. A presente dissertação objetiva mostrar a viabilidade técnica e econômica dos painéis para paredes internas, na Bolívia; para tanto realizou-se uma avaliação dos recursos disponíveis (gesso), com relação às reservas, produção e custos. A técnica adotada na produção dos painéis é a de pré-mistura, que permite a moldagem dos painéis manual ou mecanicamente com equipamentos simples e de baixo custo. O estudo do compósito de gesso reforçado com fibra de vidro (GRG) foi realizado com gesso brasileiro e com gesso boliviano, verificando-se o seu comportamento mecânico com diferentes teores de fibra de vidro. Verificou-se aumento da resistência a tração na flexão e diminuição da resistência a compressão com o aumento do teor de fibra de vidro. A avaliação do comportamento mecânico dos painéis foi feita através dos ensaios de impacto (corpo mole e corpo duro). Nos ensaios de corpo mole, verificou-se aumento da resistência com o aumento do teor de fibra de vidro. Os teores de 0,75% e 1,5% se mostraram suficientes para que os painéis de GRG satisfaçam os requisitos de desempenho para divisórias internas respectivamente para o gesso brasileiro e boliviano. O comportamento dos painéis nos ensaios de impacto de corpo duro foi satisfatório, tanto para painéis com fibra como para painéis sem fibra de vidro. No estudo preliminar de custos, verificou-se uma redução em torno de 36% para os painéis de GRG em relação às paredes intemas tradicionalmente usadas na Bolívia.

Compósitos de polipropileno com fibra de vidro utilizando viniltrietoxisilano como agente de adesão

Compósitos de polipropileno (PP) com cargas inorgânicas tem sido cada vez mais aplicados na obtenção de peças automotivas, eletrodomésticos e outros. O crescimento da aplicação destes materiais foi possível com o advento da tecnologia de adesão que consiste no uso de um agente que promove a interação físico-química na interface carga/matriz. Neste trabalho, o viniltrietoxisilano (VTES) foi empregado como agente de adesão em compósitos de PP com fibras de vidro curtas. A reação do VTES com PP por via radicalar foi estudada em câmara de mistura e por extrusão reativa, comparando-se os dois processos. O VTES reage com o PP na ausência de iniciador de reação radicalar em processos com alto cisalhamento. A reação modifica o comportamento reológico do polímero, sem afetar significativamente as propriedades térmicas e mecânicas. O teor de VTES tem influência sobre o peso molecular de produtos sem peróxido. Compósitos de PP contendo 20% de fibras de vidro foram obtidos por extrusão reativa e câmara de mistura, analisando-se o efeito de VTES sobre as propriedades mecânicas, reológicas e a morfologia dos produtos. Um estudo das condições de processamento por extrusão reativa é apresentado, comparando dois métodos a) pré-impregnação do polímero com os reagentes e b) adição de uma solução dos reagentes num estágio avançado da extrusora. A quebra diferenciada das fibras durante o processamento por extrusão pode ser explicada através comportamento reológico observado pelas medidas de torque na câmara de mistura O VTES age no sentido de promover a adesão na interface matriz / fibra, o que pode ser verificado pela morfologia do material. A degradação do material é influenciada pela exposição ao ar, pelo tempo de residência e pela temperatura na extrusão. O módulo dos compósitos contendo VTES é dependente do comprimento das fibras. A tensão de ruptura aumenta em presença de VTES.

Utilização de resíduo lignocelulósico na obtenção de chapa de madeira aglomerada homogênea e compósito reforçado com fibra de vidro-E

This research is about the use of the coconut´s endocarp (nucifera linn) and the waste of derivatives of wood and furniture as raw material to technological use. In that sense, the lignocellulosic waste is used for manufacture of homogeneous wood sheet agglomerate (LHWS) and lignocellulosic load which take part of a polymeric composite with fiber glass E (GFRP-WC). In the manufacturing of the homogeneous wood sheet agglomerate (LHWS), it was used mamona´s resin as waste s agglutinating element. The plates were taken up in a hydraulic press engine, heated, with temperature control, where they were manufactured for different percentage of waste wood and coconuts nucífera linn. Physical tests were conducted to determine the absorption of water, density, damp grade (in two hours and twenty-four hours), swelling thickness (in two hours and twenty-four hours), and mechanical tests to evaluate the parallel tensile strength (internal stick) and bending and the static (steady) flexural. The physical test´s results indicate that the LHWS can be classified as bonded wood plate of high-density and with highly water resistant. In the mechanical tests it was possible to establish that LHWS presents different characteristics when submitted to uniaxial tensile and to the static (steady) flexural, since brittle and elasticity module had a variation according to the amount of dry endocarp used to manufacture each trace of LHWS. The GFRP-WC was industrially manufactured by a hand-lay-up process where the fiber glass E was used as reinforcement the lignocellulósic´s waste as load. The matrix was made with ortofitalic unsaturated polyester resin. Physical and mechanical tests were performed in presence of saturated humidity and dry. The results indicated good performance of the GFRP-WC, as traction as in flexion in three points. The presence of water influenced the modules obtained in the flexural and tensile but there were no significant alteration in the properties analyzed. As for the fracture, the analysis showed that the effects are more harmful in the presence of damp, under the action of loading tested, but despite this, the fracture was well defined starting in the external parts and spreading to the internal regions when one when it reaches the hybrid load

Avaliação de concretos reforçados por confinamento com manta de fibra de vidro estrutural e pré-impreganada

Due to the occurrence of diseases in the use of structural reinforcements in composites, with presentation of concrete blanket detachment, has been identified the need to evaluate the performance of concrete reinforced with glass fiber. This study aims to evaluate these concretes by means of testing methodologies, using concrete with low resistance with structural reinforcement for confinement by preimpregnated glass fiber and traditional fiberglass blanket. The first stage of work was the development of methodologies for analysis, opting for four types, such as the acoustic survey, strength to compressive, the pull-off and ultrasound. Next, tests were carried out using the four selected methodologies in 30 of proof-of-specimens by 5x10 cm, 15 were reinforced with the traditional fiberglass blanket with 5specimens exposed to test a marine environment of marine coastline of Natal-RN and 15 were reinforced with a pre-impregnated glass fiber blanket, as well as 5specimens exposed to a test environment of the marine coastline of Natal-RN. After conducting the acoustic survey, it has been verified a lack of delaminating and air bubbles in the samples, confirming the absence of gross shortcomings in the implementation of the ribs both the traditional fiberglass blanket and in the preimpregnated fiber glass blanket. After carrying out methods of pull-off and compressive strengthening test it was observed that the reinforced proof-bodies with pre-impregnated glass blanket showed maximum stresses higher than the traditional fiberglass blanket; consequently a greater grip with the formation of a smaller area of . fracture, unlike traditional glass mat, which showed lower maximum stresses, with a greater area of fracture. It was also found that the traditional fiberglass blanket presented detachment of blanket-concrete interface, unlike the pre-impregnated fiberglass blanket, which showed a better grip on the blanket-concrete interface. In the trial of ultrasound there was no presence of cracks in the blanket-concrete interface, yielding to both blankets good compactness of the concrete. At the end of this work, they were developed and proposed two methods of testing for evaluation of reinforced concrete structures with composites, for standardization, the acoustic survey and pull-off

Estudo comparativo de pás para aerogeradores de grande porte fabricadas em materiais compósitos reforçadas com fibra de carbono ou fibra de vidro

The research and development of wind turbine blades are essential to keep pace with worldwide growth in the renewable energy sector. Although currently blades are typically produced using glass fiber reinforced composite materials, the tendency for larger size blades, particularly for offshore applications, has increased the interest on carbon fiber reinforced composites because of the potential for increased stiffness and weight reduction. In this study a model of blade designed for large generators (5 MW) was studied on a small scale. A numerical simulation was performed to determine the aerodynamic loading using a Computational Fluid Dynamics (CFD) software. Two blades were then designed and manufactured using epoxy matrix composites: one reinforced with glass fibers and the other with carbon fibers. For the structural calculations, maximum stress failure criterion was adopted. The blades were manufactured by Vacuum Assisted Resin Transfer Molding (VARTM), typical for this type of component. A weight comparison of the two blades was performed and the weight of the carbon fiber blade was approximately 45% of the weight of the fiberglass reinforced blade. Static bending tests were carried out on the blades for various percentages of the design load and deflections measurements were compared with the values obtained from finite element simulations. A good agreement was observed between the measured and calculated deflections. In summary, the results of this study confirm that the low density combined with high mechanical properties of carbon fibers are particularly attractive for the production of large size wind turbine blades

Estratégia de produção e competitividade :estudo de caso com enfoque de estratégia de foco em empresas de fibra de vidro

The objective of this thesis is to study the theory of production as it relates to and focuses on the strategy of production and competitiveness. The theory utilized was based on Terry Hill s Strategies through the utilization of Matrix of Manufacturing Strategy Issues and supported by the studies of others in this area. The methodology used for the development of this study was based on observing the engagement between two companies over a long period of time. Through interviews and discussions it was possible to collect the necessary information to guide this study; and by constant involvement in each of these companies, their ways of thinking, performing and administrating were observed and understood. In conclusion, this work created an understanding of the importance of the strategy of production, not as the only important element but as an important factor to direct attitudes and decisions in the company under the concept of strategy and competitiveness

Avaliação do comportamento tribológico de compósitos poliéster/fibra de vidro utilizando resíduos de poliéster/fibra de vidro e carbonato de cálcio como carga

The use of composite materials and alternative is being increased every day, as it becomes more widespread awareness that the use of renewable and not harmful to the environment is part of a new environmentally friendly model. Since its waste (primarily fiberglass) can not be easily recycled by the difficulty that still exists in this process, since they have two phases mixed, a polymeric matrix thermoset difficult to recycle because it is infusible and phase of fiber reinforcements. Thermoset matrix composites like Polyester + fiberglass pose a threat due to excessive discharge. Aiming to minimize this problem, aimed to reuse the composite Polyester + fiber glass, through the wastes obtained by the grinding of knifes and balls. These residues were incorporated into the new composite Polyester/Fiberglass for hot compression mold and compared tribological to composites with filler CaCO3, generally used as filler, targeting a partial replacement of CaCO3 by such waste. The composites were characterized by thermal analysis (TGA, DSC and DMA), by the surface integrity (roughness determination, contact angle and surface energy), mechanical properties (hardness) and tribological tests (wear and coefficient of dynamic friction) in order to evaluate the effect of loads and characterize these materials for applications that can take, in the tribological point of view since waste Polyester + fiberglass has great potential for replacement of CaCO3

Aproveitamento dos resíduos de compósitos à base de resina poliéster e fibra de vidro

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Reciclagem química por hidrólise da poliamida 6,6 reforçada com fibra de vidro após ciclos de reciclagem mecânica

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Avaliação do desempenho de compósitos de PPA/Fibra de vidro para aplicação em bombas de óleo de motores de motocicletas

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Efeito de material cimentante e do tempo na resistência adesiva de pinos de fibra de vidro

Pós-graduação em Ciências Odontológicas - FOAR

Resistência a extrusão de retentores intra-radiculares de fibra de vidro avaliando: técnica de confecção e cimento resinoso

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação por microdureza Vickers da profundidade de polimerização de cimentos resinosos na cimentação de pinos de fibra de vidro empregando diferentes fontes de luz

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito da ciclagem mecânica sobre a resistência de união de pinos intra-radiculares de fibra cimentados com resina à dentina

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência de sistemas adesivos e da região do dente na durabilidade da união entre dentina e pino de fibra

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)