Monitoring scan asymmetry of microwave humidity sounding channels using simultaneous all angle collocations (SAACs)

Simultaneous all angle collocations (SAACs) of microwave humidity sounders (AMSU-B and MHS) on-board polar orbiting satellites are used to estimate scan-dependent biases. This method has distinct advantages over previous methods, such as that the estimated scan-dependent biases are not influenced by diurnal differences between the edges of the scan and the biases can be estimated for both sides of the scan. We find the results are robust in the sense that biases estimated for one satellite pair can be reproduced by double differencing biases of these satellites with a third satellite. Channel 1 of these instruments shows the least bias for all satellites. Channel 2 has biases greater than 5 K, thus needs to be corrected. Channel 3 has biases of about 2 K and more and they are time varying for some of the satellites. Channel 4 has the largest bias which is about 15 K when the data are averaged for 5 years, but biases of individual months can be as large as 30 K. Channel 5 also has large and time varying biases for two of the AMSU-Bs. NOAA-15 (N15) channels are found to be affected the most, mainly due to radio frequency interference (RFI) from onboard data transmitters. Channel 4 of N15 shows the largest and time varying biases, so data of this channel should only be used with caution for climate applications. The two MHS instruments show the best agreement for all channels. Our estimates may be used to correct for scan-dependent biases of these instruments, or at least used as a guideline for excluding channels with large scan asymmetries from scientific analyses.

Bioactive glass sol-gel foam scaffolds:evolution of nanoporosity during processing and in situ monitoring of apatite layer formation using small- and wide-angle X-ray scattering

Recent work has highlighted the potential of sol-gel-derived calcium silicate glasses for the regeneration or replacement of damaged bone tissue. The work presented herein provides new insight into the processing of bioactive calcia-silica sol-gel foams, and the reaction mechanisms associated with them when immersed in vitro in a simulated body fluid (SBF). Small-angle X-ray scattering and wide-angle X-ray scattering (diffraction) have been used to study the stabilization of these foams via heat treatment, with analogous in situ time-resolved data being gathered for a foam immersed in SBF. During thermal processing, pore sizes have been identified in the range of 16.5-62.0 nm and are only present once foams have been heated to 400 degrees C and above. Calcium nitrate crystallites were present until foams were heated to 600 degrees C; the crystallite size varied from 75 to 145 nm and increased in size with heat treatment up to 300 degrees C, then decreased in size down to 95 rim at 400 degrees C. The in situ time-resolved data show that the average pore diameter decreases as a function of immersion time in SBF, as calcium phosphates grow on the glass surfaces. Over the same time, Bragg peaks indicative of tricalcium phosphate were evident after only 1-h immersion time, and later, hydroxycarbonate apatite was also seen. The hydroxycarbonate apatite appears to have preferred orientation in the (h,k,0) direction.

Transcranial Electrocortical Stimulation to Monitor the Facial Nerve Motor Function During Cerebellopontine Angle Surgery

OBJECTIVE: This study was conducted to investigate the success rate of using the facial motor evoked potential (FMEP) of orbicularis oculi and oris muscles for facial nerve function monitoring with use of a stepwise protocol, and its usefulness in predicting facial nerve outcome during cerebellopontine angle (CPA) surgeries. METHODS: FMEPs were recorded intraoperatively from 60 patients undergoing CPA surgeries. Transcranial electrocortical stimulation (TES) was performed using corkscrew electrodes positioned at hemispheric montage (C3/C4 and CZ). The contralateral abductor pollicis brevis muscle was used as the control response. Stimulation was always applied contralaterally to the affected side using 1, 3, or 5 rectangular pulses ranging from 200 to 600 V with 50 mu s of pulse duration and an interstimulus interval of 2 ms. Facial potentials were recorded from needles placed in the orbicularis oculi and oris muscles. RESULTS: FMEP from the orbicularis oris and oculi muscles could be reliably monitored in 86.7% and 85% of the patients, respectively. The immediate postoperative facial function correlated significantly with the FMEP ratio in the orbicularis oculi muscle at 80% amplitude ratio (P =.037) and orbicularis oris muscle at 35% ratio (P =.000). FMEP loss was always related to postoperative facial paresis, although in different degrees. CONCLUSION: FMEPs can be obtained reliably by using TES with 3 to 5 train pulses. Stable intraoperative FMEPs can predict a good postoperative outcome of facial function. However, further refinements of this technique are necessary to minimize artifacts and to make this method more reliable.

Design Procedures and Field Monitoring of Submerged Barbs for Streambank Protection, June 2007

The main objective of this study was to evaluate the hydraulic performance of riprap spurs and weirs in controlling bank erosion at the Southern part of the Raccoon River upstream U.S. Highway 169 Bridge utilizing the commercially available model FESWMS and field monitoring. It was found based on a 2 year monitoring and numerical modeling that the design of structures was overall successful, including their spacing and stability. The riprap material incorporated into the structures was directly and favorably correlated to the flow transmission through the structure, or in other words, dictated the permeable nature of the structure. It was found that the permeable dikes and weirs chosen in this study created less volume of scour in the vicinity of the structure toes and thus have less risk comparatively to other impermeable structures to collapse. The fact that the structures permitted the transmission of flow through them it allowed fine sand particles to fill in the gaps of the rock interstices and thus cement and better stabilize the structures. During bank-full flows the maximum scour hole was recorded away from the structures toe and the scourhole size was directly related to the protrusion angle of the structure to the flow. It was concluded that the proposed structure inclination with respect to the main flow direction was appropriate since it provides maximum bank protection while creating the largest volume of local scour away from the structure and towards the center of the channel. Furthermore, the lowest potential for bank erosion also occurs with the present set-up design chosen by the IDOT. About 2 ft of new material was deposited in the area located between the structures for the period extending from the construction day to May 2007. Surveys obtained by sonar and the presence of vegetation indicate that new material has been added at the bank toes. Finally, the structures provided higher variability in bed topography forming resting pools, creating flow shade on the leeward side of the structure, and separation of bed substrate due to different flow conditions. Another notable environmental benefit to rock riprap weirs and dikes is the creation of resting pools, especially in year 2007 (2nd year of the project). The magnitude of these benefits to aquatic habitat has been found in the literature that is directly related to the induced scour-hole volume.

From Regional Landslide Detection to Site-Specific Slope Deformation Monitoring and Modelling Based on Active Remote Sensors

Landslide processes can have direct and indirect consequences affecting human lives and activities. In order to improve landslide risk management procedures, this PhD thesis aims to investigate capabilities of active LiDAR and RaDAR sensors for landslides detection and characterization at regional scales, spatial risk assessment over large areas and slope instabilities monitoring and modelling at site-specific scales. At regional scales, we first demonstrated recent boat-based mobile LiDAR capabilities to model topography of the Normand coastal cliffs. By comparing annual acquisitions, we validated as well our approach to detect surface changes and thus map rock collapses, landslides and toe erosions affecting the shoreline at a county scale. Then, we applied a spaceborne InSAR approach to detect large slope instabilities in Argentina. Based on both phase and amplitude RaDAR signals, we extracted decisive information to detect, characterize and monitor two unknown extremely slow landslides, and to quantify water level variations of an involved close dam reservoir. Finally, advanced investigations on fragmental rockfall risk assessment were conducted along roads of the Val de Bagnes, by improving approaches of the Slope Angle Distribution and the FlowR software. Therefore, both rock-mass-failure susceptibilities and relative frequencies of block propagations were assessed and rockfall hazard and risk maps could be established at the valley scale. At slope-specific scales, in the Swiss Alps, we first integrated ground-based InSAR and terrestrial LiDAR acquisitions to map, monitor and model the Perraire rock slope deformation. By interpreting both methods individually and originally integrated as well, we therefore delimited the rockslide borders, computed volumes and highlighted non-uniform translational displacements along a wedge failure surface. Finally, we studied specific requirements and practical issues experimented on early warning systems of some of the most studied landslides worldwide. As a result, we highlighted valuable key recommendations to design new reliable systems; in addition, we also underlined conceptual issues that must be solved to improve current procedures. To sum up, the diversity of experimented situations brought an extensive experience that revealed the potential and limitations of both methods and highlighted as well the necessity of their complementary and integrated uses.

The Role of Epistemic Monitoring in Language Comprehension

In der psycholinguistischen Forschung ist die Annahme weitverbreitet, dass die Bewertung von Informationen hinsichtlich ihres Wahrheitsgehaltes oder ihrer Plausibilität (epistemische Validierung; Richter, Schroeder & Wöhrmann, 2009) ein strategischer, optionaler und dem Verstehen nachgeschalteter Prozess ist (z.B. Gilbert, 1991; Gilbert, Krull & Malone, 1990; Gilbert, Tafarodi & Malone, 1993; Herbert & Kübler, 2011). Eine zunehmende Anzahl an Studien stellt dieses Zwei-Stufen-Modell von Verstehen und Validieren jedoch direkt oder indirekt in Frage. Insbesondere Befunde zu Stroop-artigen Stimulus-Antwort-Kompatibilitätseffekten, die auftreten, wenn positive und negative Antworten orthogonal zum aufgaben-irrelevanten Wahrheitsgehalt von Sätzen abgegeben werden müssen (z.B. eine positive Antwort nach dem Lesen eines falschen Satzes oder eine negative Antwort nach dem Lesen eines wahren Satzes; epistemischer Stroop-Effekt, Richter et al., 2009), sprechen dafür, dass Leser/innen schon beim Verstehen eine nicht-strategische Überprüfung der Validität von Informationen vornehmen. Ausgehend von diesen Befunden war das Ziel dieser Dissertation eine weiterführende Überprüfung der Annahme, dass Verstehen einen nicht-strategischen, routinisierten, wissensbasierten Validierungsprozesses (epistemisches Monitoring; Richter et al., 2009) beinhaltet. Zu diesem Zweck wurden drei empirische Studien mit unterschiedlichen Schwerpunkten durchgeführt. Studie 1 diente der Untersuchung der Fragestellung, ob sich Belege für epistemisches Monitoring auch bei Informationen finden lassen, die nicht eindeutig wahr oder falsch, sondern lediglich mehr oder weniger plausibel sind. Mithilfe des epistemischen Stroop-Paradigmas von Richter et al. (2009) konnte ein Kompatibilitätseffekt von aufgaben-irrelevanter Plausibilität auf die Latenzen positiver und negativer Antworten in zwei unterschiedlichen experimentellen Aufgaben nachgewiesen werden, welcher dafür spricht, dass epistemisches Monitoring auch graduelle Unterschiede in der Übereinstimmung von Informationen mit dem Weltwissen berücksichtigt. Darüber hinaus belegen die Ergebnisse, dass der epistemische Stroop-Effekt tatsächlich auf Plausibilität und nicht etwa auf der unterschiedlichen Vorhersagbarkeit von plausiblen und unplausiblen Informationen beruht. Das Ziel von Studie 2 war die Prüfung der Hypothese, dass epistemisches Monitoring keinen evaluativen Mindset erfordert. Im Gegensatz zu den Befunden anderer Autoren (Wiswede, Koranyi, Müller, Langner, & Rothermund, 2013) zeigte sich in dieser Studie ein Kompatibilitätseffekt des aufgaben-irrelevanten Wahrheitsgehaltes auf die Antwortlatenzen in einer vollständig nicht-evaluativen Aufgabe. Die Ergebnisse legen nahe, dass epistemisches Monitoring nicht von einem evaluativen Mindset, möglicherweise aber von der Tiefe der Verarbeitung abhängig ist. Studie 3 beleuchtete das Verhältnis von Verstehen und Validieren anhand einer Untersuchung der Online-Effekte von Plausibilität und Vorhersagbarkeit auf Augenbewegungen beim Lesen kurzer Texte. Zusätzlich wurde die potentielle Modulierung dieser Effeke durch epistemische Marker, die die Sicherheit von Informationen anzeigen (z.B. sicherlich oder vielleicht), untersucht. Entsprechend der Annahme eines schnellen und nicht-strategischen epistemischen Monitoring-Prozesses zeigten sich interaktive Effekte von Plausibilität und dem Vorhandensein epistemischer Marker auf Indikatoren früher Verstehensprozesse. Dies spricht dafür, dass die kommunizierte Sicherheit von Informationen durch den Monitoring-Prozess berücksichtigt wird. Insgesamt sprechen die Befunde gegen eine Konzeptualisierung von Verstehen und Validieren als nicht-überlappenden Stufen der Informationsverarbeitung. Vielmehr scheint eine Bewertung des Wahrheitsgehalts oder der Plausibilität basierend auf dem Weltwissen – zumindest in gewissem Ausmaß – eine obligatorische und nicht-strategische Komponente des Sprachverstehens zu sein. Die Bedeutung der Befunde für aktuelle Modelle des Sprachverstehens und Empfehlungen für die weiterführende Forschung zum Vehältnis von Verstehen und Validieren werden aufgezeigt.

Compact cosmic ray detector for unattended atmospheric ionisation monitoring

Two vertical cosmic ray telescopes for atmospheric cosmic ray ionization event detection are compared. Counter A, designed for low power remote use, was deployed in the Welsh mountains; its event rate increased with altitude as expected from atmospheric cosmic ray absorption. Independently, Counter B’s event rate was found to vary with incoming particle acceptance angle. Simultaneous colocated comparison of both telescopes exposed to atmospheric ionization showed a linear relationship between their event rates.

Control and analysis of oriented thin films of lipid inverse bicontinuous cubic phases using grazing incidence small-angle X‑ray scattering

Lipid cubic phases are complex nanostructures that form naturally in a variety of biological systems, with applications including drug delivery and nanotemplating. Most X-ray scattering studies on lipid cubic phases have used unoriented polydomain samples as either bulk gels or suspensions of micrometer-sized cubosomes. We present a method of investigating cubic phases in a new form, as supported thin films that can be analyzed using grazing incidence small-angle X-ray scattering (GISAXS). We present GISAXS data on three lipid systems: phytantriol and two grades of monoolein (research and industrial). The use of thin films brings a number of advantages. First, the samples exhibit a high degree of uniaxial orientation about the substrate normal. Second, the new morphology allows precise control of the substrate mesophase geometry and lattice parameter using a controlled temperature and humidity environment, and we demonstrate the controllable formation of oriented diamond and gyroid inverse bicontinuous cubic along with lamellar phases. Finally, the thin film morphology allows the induction of reversible phase transitions between these mesophase structures by changes in humidity on subminute time scales, and we present timeresolved GISAXS data monitoring these transformations.

SAXS and UV-Vis combined to Quick-XAFS monitoring of ZnO nanoparticles formation and growth

Time-resolved X-ray absorption-fine structure (Quick-XAFS) and UV-Vis absorption spectroscopies were combined for monitoring simultaneously the time evolution of Zn-based species and ZnO quantum dot (Qdot) formation and growth during the sol-gel synthesis from zinc oxy-acetate precursor solution. The time evolution of the nanostructural features of colloidal suspension was independently monitored in situ by small angle X-ray scattering (SAXS). In both cases, the monitoring was initialized just after the addition of NaOH solution (B = [OH]/[Zn] = 0.5) to the precursor solution at 40 degrees C. Combined time-resolved Quick-XAFS and UV-Vis data showed that the formation of ZnO colloids from the zinc oxy-acetate consumption achieves a quasi-steady-state chemical equilibrium in less than 200s. Afterwards, the comparison of the ZnO Qdots size and Guinier gyration radius evidences a limited aggregation process coupled to the Qdots growth. The analysis of the experimental results demonstrates that the nanocrystal coalescence and Ostwald ripening control the kinetics of the Qdot growth.

In Situ and Simultaneous UV-vis/SAXS and UV-vis/XAFS Time-Resolved Monitoring of ZnO Quantum Dots Formation and Growth

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)