TL and OSL properties of KAlSi(3)O(8):Mn, obtained by sol-gel process

Thermoluminescence (TL) and Optically Stimulated Luminescence (OSL) properties of KAlSi(3)O(8):Mn glasses obtained through the sol gel technique were investigated. Samples were obtained with five different molar concentrations of 0.25, 0.5, 1, 2 and 5 mol% of manganese. Transmission Electronic Microscopy (TEM) indicated the occurrence of nanoparticles composed by glass matrix elements with Mn. Best results for TL response were obtained with 0.5 mol% Mn doped sample, which exhibits a TL peak at 180 degrees C. The TL spectrum of this sample presents a broad emission band from 450 to 700 nm with a peak at 575 nm approximately. The emission band fits very well with the characteristic lines of the Mn(2+) emission features. According to this fact, the band at 410 nm can be ascribed to (6)A(1)(S) -> (4)A(1)(G), (4)E(G) transition, while the 545 nm band can be attributed to the superposition of the transitions (6)A(1)(S) -> (4)T(2)(G) and (6)A(1)(S) -> (4)T(1)(G). The dependence of the TL response with the energy of X-rays (27-41 keV) showed a small decrease of the TL intensity in the high energy region. Excitation with blue LEDs showed OSL in the UV region with a fast decay component. (C) 2011 Elsevier Ltd. All rights reserved.

Assessing the completeness of optical resetting of quartz OSL in the natural environment

Resetting of previously accumulated optically stimulated luminescence (OSL) signals during transport of sediment is a fundamental requirement for reliable optical dating. The completeness of optical resetting of 46 modern-age quartz samples from a variety of depositional environments was examined. All equivalent dose (De) estimates were View the MathML source, with the majority of aeolian samples View the MathML source, and fluvial samples View the MathML source. The OSL signal of quartz originates from several trap types with different rates of charge loss during illumination. As such, incomplete bleaching may be identifiable as an increase in De from easy-to-bleach through to hard-to-bleach components. For all modern fluvial samples with non-zero De values, SAR De(t) analysis and component-resolved linearly modulated OSL (LM OSL) De estimates showed this to be the case, implying incomplete resetting of previously accumulated charge. LM OSL measurements were also made to investigate the extent of bleaching of the slow components in the natural environment. In aeolian sediments examined, the natural LM OSL was effectively zero (i.e. all components were fully reset). The slow components of modern fluvial samples displayed measurable residual signals up to 15 Gy.

TL, OSL and ESR studies on beryllium oxide

Electron spin resonance (ESR) studies were carried out to identify the defect centres responsible for the thermoluminescence (TL) and optically stimulated luminescence (OSL) processes in BeO phosphor. Two defect centres were identified in irradiated BeO phosphor by ESR measurements, which were carried out at room temperature and these were assigned to an O(-) ion and Al(2+) centre. The O(-) ion (hole centre) correlates with the main 190 degrees C TL peak. The Al(2+) centre (electron centre), which acts as a recombination centre, also correlates to the 190 degrees C TL peak. A third centre, observed during thermal annealing studies, is assigned to an O(-) ion and is related to the high temperature TL at 317 degrees C. This centre also appears to be responsible for the observed OSL process in BeO phosphor. (c) 2010 Elsevier B.V. All rights reserved.

Proposal of a Brazilian accreditation program for personal dosimetry using OSL

After the development of the highly sensitive material Al(2)O(3):C, personal dosimetry using optically stimulated luminescence (OSL) has been continuously adopted in place of thermoluminescence dosimeters (TLD) by different countries (e.g. USA and Japan). In order to use a dosimetric system in Brazil it is necessary to develop a protocol and to fulfill performance and type tests in accordance with the accreditation program approved by the responsible governmental committee. This paper presents a proposal for an accreditation program for OSL personal dosimetry using a commercial dosimetric system, including tests that follow the same rules as applied to TLD and film dosimetry. The experimental results are within the reliability interval and in accordance to the expected behavior. A new test concerning re-analysis of exposed badges is also proposed. (C) 2009 Elsevier Ltd. All rights reserved.

Thermal history versus sedimentary history: OSL sensitivity of quartz grains extracted from rocks and sediments

The optically stimulated luminescence (OSL) sensitivity of quartz has a significant influence on luminescence dating procedures. Furthermore, identifying the natural controls of quartz OSL sensitivity is an important step towards new applications of OSL in geology such as provenance tracing. We evaluate the OSL sensitivity (total and the proportion of the informally assigned fast, medium and slow components) of single grains of quartz extracted from 10 different igneous and metamorphic rocks with known formation conditions; and from fluvial and coastal sediments with different sedimentary histories and known source rocks. This sample suite allows assessment of the variability of the OSL sensitivity of single quartz grains with respect to their primary origin and sedimentary history. We observed significant variability in the OSL sensitivity of grains within all studied rock and sediment samples, with the brightest grains of each sample being those dominated by the fast component. Quartz from rocks formed under high temperature (> 500 degrees C) conditions, such as rhyolites and metamorphic rocks from the amphibolite facies, display higher OSL sensitivity. The OSL sensitivity of fluvial sediments which have experienced only a short transport distance is relatively low. These sediments show a small increase in OSL sensitivity downstream, mainly due to a decreasing fraction of ""dim"" grains. The quartz grains from coastal sands present very high sensitivity and variability, which is consistent with their long sedimentary history. The high variability of the OSL sensitivity of quartz from coastal sands is attributed more to the mixture of grains with distinct sedimentary histories than to the provenance from many types of source rocks. The temperature of crystallization and the number of cycles of burial and solar exposure are suggested as the main natural factors controlling the OSL sensitivity of quartz grains. The increase in OSL sensitivity due to cycles of erosion and deposition surpasses the sensitivity inherited from the source rock, with this increase being mainly related to the sensitization of fast OSL components. The discrimination of grains with different sedimentary histories through their OSL sensitivities can allow the development of quantitative provenance methods based on quartz. (C) 2010 Elsevier B.V. All rights reserved.

How Old Is Luzia? Luminescence Dating and Stratigraphic Integrity at Lapa Vermelha, Lagoa Santa, Brazil

During an excavation in the 1970s, a disarticulated female human skeleton, later nicknamed Luzia, was discovered at 12m depth at Lapa Vermelha rockshelter in central Brazil. Radiocarbon dating of associated charcoal suggested an age of 11.4-16.4 ka for the skeleton. The scattering of the skeletal parts, some uncertainty about the exact provenience of the skeleton, and evidence of pervasive insect turbation in the archaeological layers have raised doubts about the accuracy of the age. Luminescence dates for the depositional ages of the sediments at Lapa Vermelha are reported here. Single-grain optically stimulated luminescence (OSL) of quartz along with grain-size, chemical and micro-morphological analyses of the sediments were employed to assess stratigraphic integrity, particularly the degree of sediment mixing. These various lines of evidence point to high stratigraphic integrity with little mixing at Lapa Vermelha. Sediments closest to where Luzia was recovered give OSL ages ranging from 12.7 to 16.0 ka, thus not refuting the original dates. (C) 2010 Wiley Periodicals, Inc.

Quartz OSL sensitivity as a proxy for storm activity on the southern Brazilian coast during the Late Holocene

Natural cycles of irradiation during burial and bleaching due to solar exposure during transport increase the Optically Stimulated Luminescence (OSL) sensitivity of quartz sand grains. The relationship between the OSL sensitivity and sediment transport allows to discriminate quartz sand grains with different depositional histories. In this paper, we evaluate the variation of OSL sensitivity in quartz grains deposited during the progradation of the Ilha Comprida barrier on the southern Brazilian, coast. Changes in sand sensitivity recorded by barrier growth since 6 ka ago are controlled by the variation in the proportion of low versus high sensitivity quartz grains. Low sensitivity grains with short sedimentary history are supplied by the Ribeira de Iguape River and reach the barrier through southward alongshore currents during fair weather conditions. Storm conditions shift the alongshore currents to northeast and permit the transport of high sensitivity grains with long sedimentary history from distal southern coastal sectors to the barrier. Therefore, the input of distal sediments for the Ilha Comprida barrier depends on the frequency and intensity of storms. Thus, the OSL sensitivity can be used as proxy for storm activity. The variation of OSL sensitivity through time indicates that the Ilha Comprida barrier changed from a relatively stable to an unstable storm pattern around 2 ka ago. Periods with increased storm activity peaked around AD 500, AD 1500 and AD 1850, approximately on the boundaries of the Medieval Climate Anomaly and the Little Ice Age. (C) 2012 Elsevier B.V. All rights reserved.

Development and Implementation of the Use of Optically Stimulated Luminescent Detectors in the Radiological Physics Center Anthropomorphic Quality Assurance Phantoms

The Radiological Physics Center (RPC) uses both on-site and remote reviews to credential institutions for participation in clinical trials. Anthropomorphic quality assurance (QA) phantoms are one tool the RPC uses to remotely audit institutions, which include thermoluminescent dosimeters (TLDs) and radiochromic film. The RPC desires to switch from TLD as the absolute dosimeter in the phantoms, to optically stimulated luminescent dosimeters (OSLDs), but a problem lies in the angular dependence exhibited by the OSLD. The purpose of this study was to characterize the angular dependence of OSLD and establish a correction factor if necessary, to provide accurate dosimetric measurements as a replacement for TLD in the QA phantoms. A 10 cm diameter high-impact polystyrene spherical phantom was designed and constructed to hold an OSLD to study the angular response of the dosimeter under the simplest of circumstances for both coplanar and non-coplanar treatment deliveries. OSLD were irradiated in the spherical phantom, and the responses of the dosimeter from edge-on angles were normalized to the response when irradiated with the beam incident normally on the surface of the dosimeter. The average normalized response was used to establish an angular correction factor for 6 MV and 18 coplanar treatments, and for 6 MV non-coplanar treatments specific to CyberKnife. The RPC pelvic phantom dosimetry insert was modified to hold OSLD, in addition to the TLD, adjacent to the planes of film. Treatment plans of increasing angular beam delivery were developed, three in Pinnacle v9.0 (4-field box, IMRT, and VMAT) and one in Accuray’s MultiPlan v3.5.3 (CyberKnife). The plans were delivered to the pelvic phantom containing both TLD and OSLD in the target volume. The pelvic phantom was also sent to two institutions to be irradiated as trials, one delivering IMRT, and the other a CyberKnife treatment. For the IMRT deliveries and the two institution trials, the phantom also included film in the sagittal and coronal planes. The doses measured from the TLD and OSLD were calculated for each irradiation, and the angular correction factors established from the spherical phantom irradiations were applied to the OSLD dose. The ratio of the TLD dose to the angular corrected OSLD dose was calculated for each irradiation. The corrected OSLD dose was found to be within 1% of the TLD measured dose for all irradiations, with the exception of the in-house CyberKnife deliveries. The films were normalized to both TLD measured dose and the corrected OSLD dose. Dose profiles were obtained and gamma analysis was performed using a 7%/4 mm criteria, to compare the ability of the OSLD, when corrected for the angular dependence, to provide equivalent results to TLD. The results of this study indicate that the OSLD can effectively be used as a replacement for TLD in the RPC’s anthropomorphic QA phantoms for coplanar treatment deliveries when a correction is applied for the dosimeter’s angular dependence.

La datation du site Mailhot-Curran : application de la luminescence optique sur des poteries iroquoiennes du Saint-Laurent

La luminescence optique (OSL) a été mesurée sur dix-sept fragments de poterie collectés à Mailhot-Curran (BgFn-2), un site archéologique du Sylvicole supérieur tardif localisé dans le sud-ouest du Québec. Le but principal de ce projet était de dater ce site qui est considéré jusqu’à maintenant comme le plus récent site préhistorique de la concentration de Saint-Anicet, afin de poser un jalon dans la chronologie des sites de cette région. L’OSL a été utilisée conjointement à la datation par radiocarbone (14C) et la sériation du matériel archéologique. L’hypothèse archéologique propose que le village aurait été occupé pendant les années 1518 à 1530 de notre ère (Chapdelaine 2015a). Les résultats que nous proposons dans ce présent mémoire appuient cette proposition. Nous avons obtenu un âge de 490 ± 49 ans (année de référence : 2013), correspondant à l’année 1523 de notre ère avec une probabilité d’occupation du site Mailhot-Curran entre les années 1474 et 1572. Le programme de datation par luminescence optique a été réalisé sur des fragments de poterie domestique composés d’argile de la Mer de Champlain datant de la période du Quaternaire récent. La datation par stimulation infrarouge (IRSL) a été préférentiellement utilisée sur des aliquotes de grains fins polyminéraliques. Pour la détermination des doses équivalentes, un protocole SAR (Murray et Wintle 2000) modifié pour la mesure des feldspaths et incluant un lessivage optique a été utilisé (Lamothe et al. 2004). Les valeurs g ont été mesurées en suivant le protocole proposé par Auclair et al. (2003). La correction de Huntley et Lamothe (2001) a été utilisée afin de corriger les doses équivalentes mesurées pour la décroissance anormale du signal feldspathique. Les doses annuelles ont pour leur part été déterminées par des mesures réalisées in situ et en laboratoire. Les résultats que nous présentons dans ce mémoire sont affectés par une dispersion assez large. Cette variabilité a été prise en compte par des méthodes statistiques pour la détermination de l’âge probable de l’occupation du site Mailhot-Curran.

La datation du site Mailhot-Curran : application de la luminescence optique sur des poteries iroquoiennes du Saint-Laurent

La luminescence optique (OSL) a été mesurée sur dix-sept fragments de poterie collectés à Mailhot-Curran (BgFn-2), un site archéologique du Sylvicole supérieur tardif localisé dans le sud-ouest du Québec. Le but principal de ce projet était de dater ce site qui est considéré jusqu’à maintenant comme le plus récent site préhistorique de la concentration de Saint-Anicet, afin de poser un jalon dans la chronologie des sites de cette région. L’OSL a été utilisée conjointement à la datation par radiocarbone (14C) et la sériation du matériel archéologique. L’hypothèse archéologique propose que le village aurait été occupé pendant les années 1518 à 1530 de notre ère (Chapdelaine 2015a). Les résultats que nous proposons dans ce présent mémoire appuient cette proposition. Nous avons obtenu un âge de 490 ± 49 ans (année de référence : 2013), correspondant à l’année 1523 de notre ère avec une probabilité d’occupation du site Mailhot-Curran entre les années 1474 et 1572. Le programme de datation par luminescence optique a été réalisé sur des fragments de poterie domestique composés d’argile de la Mer de Champlain datant de la période du Quaternaire récent. La datation par stimulation infrarouge (IRSL) a été préférentiellement utilisée sur des aliquotes de grains fins polyminéraliques. Pour la détermination des doses équivalentes, un protocole SAR (Murray et Wintle 2000) modifié pour la mesure des feldspaths et incluant un lessivage optique a été utilisé (Lamothe et al. 2004). Les valeurs g ont été mesurées en suivant le protocole proposé par Auclair et al. (2003). La correction de Huntley et Lamothe (2001) a été utilisée afin de corriger les doses équivalentes mesurées pour la décroissance anormale du signal feldspathique. Les doses annuelles ont pour leur part été déterminées par des mesures réalisées in situ et en laboratoire. Les résultats que nous présentons dans ce mémoire sont affectés par une dispersion assez large. Cette variabilité a été prise en compte par des méthodes statistiques pour la détermination de l’âge probable de l’occupation du site Mailhot-Curran.

Multiple phases of North African humidity recorded in lacustrine sediments from the Fazzan Basin, Libyan Sahara

The Fazzan Basin of south-west Libya is at present arid with less than 20 mm of rainfall per annum. However, regionally extensive limestones, lacustrine sands and coquina (fossiliferous carbonate rock) deposits show that the Fazzan Basin previously contained a large palaeolake, indicating that the climate in the past was more humid. Optically stimulated luminescence (OSL) dating techniques have been applied to key lacustrine deposits within the basin in an attempt to provide an internally consistent chronology for this humidity record. Results indicate that palaeolake sediments within the Fazzan Basin record a very long history of palacohydrological change, ranging from present day and conditions to humidity capable of sustaining a lake with an approximate area of 76,250 km(2). The existence of humid periods in mid oxygen isotope stage 5 and the early Holocene is confirmed. An older lacustrine event, tentatively correlated to oxygen isotope stage 11, is also recognized. In addition, evidence is presented for at least two humid phases beyond the age range over which the conventional OSL dating technique is applicable. This study demonstrates that OSL dating of palaeolake sediments within the Fazzan Basin offers the potential to provide a detailed record of North African humidity spanning several glacial-interglacial cycles. (c) 2006 Elsevier Ltd. All rights reserved.

Holocene settlement shifts and paleoenvironments on the Central Iranian Plateau: investigating linked systems

For thousands of years, humans have inhabited locations that are highly vulnerable to the impacts of climate change, earthquakes, and floods. In order to investigate the extent to which Holocene environmental changes may have impacted on cultural evolution, we present new geologic, geomorphic, and chronologic data from the Qazvin Plain in northwest Iran that provides a backdrop of natural environmental changes for the simultaneous cultural dynamics observed on the Central Iranian Plateau. Well-resolved archaeological data from the neighbouring settlements of Zagheh (7170—6300 yr BP), Ghabristan (6215—4950 yr BP) and Sagzabad (4050—2350 yr BP) indicate that Holocene occupation of the Hajiarab alluvial fan was interrupted by a 900 year settlement hiatus. Multiproxy climate data from nearby lakes in northwest Iran suggest a transition from arid early-Holocene conditions to more humid middle-Holocene conditions from c. 7550 to 6750 yr BP, coinciding with the settlement of Zagheh, and a peak in aridity at c. 4550 yr BP during the settlement hiatus. Palaeoseismic investigations indicate that large active fault systems in close proximity to the tell sites incurred a series of large (MW ~7.1) earthquakes with return periods of ~500—1000 years during human occupation of the tells. Mapping and optically stimulated luminescence (OSL) chronology of the alluvial sequences reveals changes in depositional style from coarse-grained unconfined sheet flow deposits to proximal channel flow and distally prograding alluvial deposits sometime after c. 8830 yr BP, possibly reflecting an increase in moisture following the early-Holocene arid phase. The coincidence of major climate changes, earthquake activity, and varying sedimentation styles with changing patterns of human occupation on the Hajiarab fan indicate links between environmental and anthropogenic systems. However, temporal coincidence does not necessitate a fundamental causative dependency.

New age estimates for the Palaeolithic assemblages and Pleistocene succession of Casablanca, Morocco

Marine and aeolian Quaternary sediments from Casablanca, Morocco were dated using the optically stimulated luminescence (OSL) signal of quartz grains. These sediments form part of an extensive succession spanning the Pleistocene, and contain a rich faunal and archaeological record, including an Acheulian lithic assemblage from before the Brunhes–Matayama boundary, and a Homo erectus jaw from younger cave deposits. Sediment samples from the sites of Reddad Ben Ali, Oulad J’mel, Sidi Abderhamane and Thomas Quarries have been dated, in order to assess the upper limits of OSL. The revision of previously measured mammalian tooth enamel electron spin resonance (ESR) dates from the Grotte des Rhinocéros, Oulad Hamida Quarry 1, incorporating updated environmental dose rate measurements and attenuation calculations, also provide chronological constraint for the archaeological material preserved at Thomas Quarries. Several OSL age estimates extend back to around 500,000 years, with a single sample providing an OSL age close to 1 Ma in magnetically reversed sediments. These luminescence dates are some of the oldest determined, and their reliability is assessed using both internal criteria based on stratigraphic consistency, and external lithostratigraphic, morphostratigraphic and independent chronological constraints. For most samples, good internal agreement is observed using single aliquot regenerative-dose OSL measurements, while multiple aliquot additive-dose measurements generally have poorer resolution and consistency. Novel slow-component and component-resolved OSL approaches applied to four samples provide significantly enhanced dating precision, and an examination of the degree of signal zeroing at deposition. A comparison of the OSL age estimates with the updated ESR dates and one U-series date demonstrate that this method has great potential for providing reliable age estimates for sediments of this antiquity. We consider the cause of some slight age inversion observed at Thomas Quarries, and provide recommendations for further luminescence dating within this succession.

Optical dating of quartz from young samples and the effects of pre-heat temperature

The optically stimulated luminescence (OSL) signal within quartz may be enhanced by thermal transfer during pre-heating. This may occur via a thermally induced charge transfer from low temperature traps to the OSL traps. Thermal transfer may affect both natural and artificially irradiated samples. The effect, as empirically measured via recuperation tests, is typically observed to be negligible for old samples (<1% of natural signal). However, thermal transfer remains a major concern in the dating of young samples as thermal decay and transfers of geologically unstable traps (typically in the TL range 160–280°C) may be incomplete. Upon pre-heating such a sample might undergo thermal transfer to the dating trap and result in a De overestimate. As a result, there has been a tendency for workers to adopt less rigorous pre-heats for young samples. We have investigated the pre-heat dependence of 23 young quartz samples from various depositional environments using pre-heats between 170°C and 300°C, employing the single aliquot regeneration (SAR) protocol. SAR De's were also calculated for 25 additional young quartz samples of different depositional environments and compared with previous multiple aliquot additive dose (MAAD) data. Results demonstrate no significant De dependence upon pre-heat temperatures. A close correspondence between MAAD data and the current SAR data for the samples tested is also illustrated.