Modelización de contactos termoelastohidrodinámicos

La mejora en la eficiencia energética y la reducción de la tasa de fallos en los contactos lubricados son aspectos que resultan de gran interés en numerosos sectores de la industria, y plantean en estos momentos nuevas dificultades operativas y retos para un futuro próximo. Los avances tecnológicos han incrementado las exigencias técnicas que se requieren a los aceites para cumplir su función al extender sus variables operativas a un mayor espectro de aplicaciones, tanto de condiciones de funcionamiento como a la gran variedad de nuevos materiales constitutivos de los engranajes en los que se tiene que utilizar. Por ello, actualmente se está incentivado el desarrollo de nuevos procedimientos que permitan comprender el comportamiento de este tipo de contactos lubricados, con el fin de lograr mejoras técnicas en su diseño y la correcta selección del aceite. En esta Tesis Doctoral se presenta una metodología de cálculo numérico que permite simular el comportamiento de contactos elastohidrodinámicos (EHD) puntuales, como puede ser el caso de un rodamiento. La resolución de este problema presenta diversas complejidades matemáticas y exige el desarrollo de un elaborado procedimiento de cálculo basado en técnicas multinivel. Para hacer del procedimiento una herramienta válida en un gran número de condiciones de funcionamiento y tipos de lubricantes, se ha tenido en cuenta en el cálculo la posible aparición de comportamientos no-Newtonianos del lubricante y fenómenos de generación y disipación de calor, provocados por el movimiento relativo del fluido y las superficies en contacto. Para la validación del procedimiento, se han contrastado los resultados numéricos obtenidos con nuestro método, con los resultados numéricos y experimentales publicados por otros autores y con valores experimentales propios medidos en un equipo de ensayo de contacto puntual tipo MTM. El desarrollo de este programa ha dotado a la División de Ingeniería de Máquinas de una herramienta que ha permitido, y sobre todo va permitir, evaluar la importancia de cada uno de los parámetros reológicos en los diferentes problemas que va a tener que abordar, evaluación que hasta el momento se realizaba con métodos aproximados que describen la fenomenología con mucha menos precisión. A la hora de emplear nuestro procedimiento numérico para simular situaciones reales, nos hemos encontrado con el obstáculo de que es muy complicado encontrar, en la bibliografía y bases de datos, los parámetros que caracterizan el comportamiento reológico del lubricante en las condiciones de presión, temperatura y grado de cizallamiento habituales en las que se trabaja en este tipo de contactos, y las pocas medidas que existen para estas condiciones de funcionamiento son poco fiables. Por ello como complemento al objetivo principal de esta Tesis hemos desarrollado una metodología para caracterizar los lubricantes en estas condiciones extremas. Dicha metodología está basada en la buena descripción que hace nuestro programa del coeficiente de fricción, lo que nos ha permitido obtener los parámetros reológicos del III lubricante a partir de las medidas experimentales del coeficiente de fricción generado en un equipo MTM lubricado con el lubricante que se desea caracterizar. Madrid, Octubre de 2012 IV Improving energy efficiency and reducing the failure rate in lubricated contacts are issues that are of great interest in many sectors of industry, and right now posed operational difficulties and new challenges for the near future. Technological advances have increased the technical demands required to oils to fulfil its role by extending its operational variables to a wider range of applications, both operating conditions and to the wide variety of new materials which constitute the gear in which must be used. For this reason, has being encouraged currently to develop new procedures to understand the behaviour of this type of lubricated contacts, in order to achieve improvements in design techniques and the correct oil selection. In this Thesis we present a numerical methodology to simulate the puntual elastohydrodynamic contact behaviour (EHD), such as a roller bearing. The resolution of this problem presents various mathematical complexities and requires the development of an elaborate calculation procedure based on multilevel techniques. To make the procedure a valid tool in a wide range of operating conditions and types of lubricants, has been taken into account in calculating the possible occurrence of non-Newtonian behaviour of the lubricant and phenomena of generation and dissipation of heat, caused by the fluid relative motion and contacting surfaces. For the validation of the method, we have compared the numerical results obtained with our method with numerical and experimental results published by other authors also with own experimental values measured on point-contact test equipment MTM. The development of this program has provided the Machines Engineering Division of a tool that has allowed, and especially will allow to evaluate the importance of each of the rheological parameters on the various problems that will have to be addressed, evaluation performed hitherto described methods that phenomenology approximated with much less accuracy. When using our numerical procedure to simulate real situations we have encountered the obstacle that is very difficult to find, in the literature and database, parameters characterizing the rheological behaviour of the lubricant in the usual conditions of pressure, temperature and shear rate in which you work in this type of contact, and the few measures that exist for these operating conditions are unreliable. Thus in addition to the main objective of this thesis, we have developed a methodology to characterize the lubricants in these extreme conditions. This methodology is based on the good description, which makes our program, of the coefficient of friction, that allowed us to obtain the lubricant rheological parameters from experimental measurements of the friction coefficient generated on lubricated MTM equipment with the lubricant to be characterized.

Simulation of the cake formation and growth in cake filtration

A computer model was developed to simulate the cake formation and growth in cake filtration at an individual particle level. The model was shown to be able to generate structural information and quantify the cake thickness, average cake solidosity, filtrate volume, filtrate flowrate for constant pressure filtration or pressure drop across the filter unit for constant rate filtration as a function of filtration time. The effects of particle size distribution and key operational variables such as initial filtration flowrate, maximum pressure drop and initial solidosity were examined based on the simulated results. They are qualitatively comparable to those observed in physical experiments. The need for further development in simulation was also discussed. (c) 2006 Elsevier Ltd. All rights reserved.

Visual performance of the human eye with soft hydrophilic contact lenses

The recording of visual acuity using the Snellen letter chart is only a limited measure of the visual performance of an eye wearing a refractive aid. Qualitative in addition to quantitative information is required to establish such a parameter: spatial, temporal and photometric aspects must all be incorporated into the test procedure. The literature relating to the correction of ametropia by refractive aids was reviewed. Selected aspects of a comparison between the correction provided by spectacles and contact lenses were considered. Special attention was directed to soft hydrophilic contact lenses. Despite technological advances which have produced physiologically acceptable soft lenses, there still remain associated with this recent form of refractive aid unpredictable visual factors. Several techniques for vision assessment were described, and previous studies of visual performance were discussed. To facilitate the investigation of visual performance in a clinical environment, a new semi-automated system was described: this utilized the presentation of broken ring test stimuli on a television screen. The research project comprised two stages. Initial work was concerned with the validation of the television system, including the optimization of its several operational variables. The second phase involved the utilization of the system in an investigation of visual performance aspects of the first month of regular daily soft contact lens wear by experimentally-naive subjects. On the basis of the results of this work an ‘homoeostatic’ model has been proposed to represent the strategy which an observer adopts in order to optimize his visual performance with soft contact lenses.

Estudo paramétrico da injeção de vapor em reservatórios delgados

Exploration of heavy oil reservoirs is increasing every year in worldwide, because the discovery of light oil reservoirs is becoming increasingly rare. This fact has stimulated the research with the purpose of becoming viable, technically and economically, the exploration of such oil reserves. In Brazil, in special in the Northeast region, there is a large amount of heavy oil reservoir, where the recovery by the so called secondary methods Water injection or gas injection is inefficient or even impracticable in some reservoirs with high viscosity oils (heavy oils). In this scenario, steam injection appears as an interesting alternative for recover of these kinds of oil reservoirs. Its main mechanism consists of oil viscosity reduction through steam injection, increasing reservoir temperature. This work presents a parametric simulation study of some operational and reservoir variables that had influence on oil recovery in thin reservoirs typically found in Brazilian Northeast Basins, that use the steam injection as improved oil recovery method. To carry out simulations, it was used the commercial software STARS (Steam, Thermal, and Advanced Processes Reservoir Simulator) from CMG (Computer Modeling Group) version 2007.11. Reservoirs variables studied were horizontal permeability, vertical and horizontal permeability ratio, water zone and pay zone thickness ratio, pay zone thickness and thermal conductivity of the rock. Whereas, operational parameters studied were distance between wells and steam injection rate. Results showed that reservoir variables that had more influence on oil recovery were horizontal permeability and water zone and pay zone thickness ratio. In relation to operational variables, results showed that short distances between wells and low steam injection rates improved oil recovery

Evaluation of the improvements on pharmacy technicians' work practices after implementation of operational procedures

Several antineoplasic drugs have been demonstrated to be carcinogenic or to have mutagenic and teratogenic effects. The greatest protection is achieved with the implementation of administrative and engineering controls and safety procedures. Objective: to evaluate the improvements on pharmacy technicians' work practices, after the implementation of operational procedures related to individual protection, biologic safety cabinet disinfection and cytotoxic drug preparation. Method: case-study in a hospital pharmacy undergoing a certification process. Six pharmacy technicians were observed during their daily activities. Characterization of the work practices was made using a checklist based on ISOPP and PIC guidelines. The variables studied concerning cleaning/disinfection procedures, personal protective equipment and procedures for preparing cytotoxic drugs. The same work practices were evaluated after four months of operational procedures implementation. Concordance between work practices and guidelines was considered to be a quality indicator (guidelines concordance practices number/total number of practices x 100). Results: improvements were observed after operational procedures implementation. An improvement of 6,25% in personal protective equipment practice was achieved by changing second pair of gloves every thirty minutes. The major progress, 10%, was obtained in disinfection procedure, where 80% of tasks are now realized according to guidelines.By now, we hot an improvement of only 1% at drug preparation procedure by placing one cytotoxic drug at a time inside the biological safety cabinet. Then, 85% of practices are according to guidelines. Conclusion: before operational procedures implementation 80,3% of practices were according to the guidelines, while now is 84,4%. This indicates that is necessary to review the procedures frequently in the benefit to reduce the risks associated with handling cytotoxic drugs and maintenance of drug specifications.

Clinical variables associated with leprosy reactions and persistence of physical impairment

Introduction Leprosy is a chronic disease that affects skin and peripheral nerves. Disease complications include reactional episodes and physical impairment. One World Health Organization (WHO) goal of leprosy programs is to decrease the number of grade 2 impairment diagnoses by 2015. This study aims to evaluate clinical factors associated with the occurrence of leprosy reactions and physical impairment in leprosy patients. Methods We conducted a retrospective study of data from medical records of patients followed in two important centers for the treatment of leprosy in Aracaju, Sergipe, Brazil, from 2005 to 2011. We used the chi-square test to analyze associations between the following categorical variables: gender, age, operational classification, clinical forms, leprosy reactions, corticosteroid treatment, and physical impairment at the diagnosis and after cure. Clinical variables associated with multibacillary leprosy and/or reactional episodes and the presence of any grade of physical impairment after cure were evaluated using the logistic regression model. Results We found that men were more affected by multibacillary forms, reactional episodes, and grade 2 physical impairment at diagnosis. Leprosy reactions were detected in a total of 40% of patients and all were treated with corticosteroids. However, physical impairment was observed in 29.8% of the patients analyzed at the end of the treatment and our multivariate analysis associated a low dose and short period of corticosteroid treatment with persistence of physical impairments. Conclusions Physical impairment should receive an increased attention before and after treatment, and adequate treatment should be emphasized.

Adaptation to experimental alterations of the operational sex ratio in populations of Drosophila melanogaster.

Theory predicts that males adapt to sperm competition by increasing their investment in testis mass to transfer larger ejaculates. Experimental and comparative data support this prediction. Nevertheless, the relative importance of sperm competition in testis size evolution remains elusive, because experiments vary only sperm competition whereas comparative approaches confound it with other variables, in particular male mating rate. We addressed the relative importance of sperm competition and male mating rate by taking an experimental evolution approach. We subjected populations of Drosophila melanogaster to sex ratios of 1:1, 4:1, and 10:1 (female:male). Female bias decreased sperm competition but increased male mating rate and sperm depletion. After 28 generations of evolution, males from the 10:1 treatment had larger testes than males from other treatments. Thus, testis size evolved in response to mating rate and sperm depletion, not sperm competition. Furthermore, our experiment demonstrated that drift associated with sex ratio distortion limits adaptation; testis size only evolved in populations in which the effect of sex ratio bias on the effective population size had been compensated by increasing the numerical size. We discuss these results with respect to reproductive evolution, genetic drift in natural and experimental populations, and consequences of natural sex ratio distortion.

Supply chain integration: studies on linking customer responsiveness and operational efficiency in logistics policy planning

Abstract The research problem in the thesis deals with improving the responsiveness and efficiency of logistics service processes between a supplier and its customers. The improvement can be sought by customizing the services and increasing the coordination of activities between the different parties in the supply chain. It is argued that to achieve coordination the parties have to have connections on several levels. In the framework employed in this research, three contexts are conceptualized at which the linkages can be planned: 1) the service policy context, 2) the process coordination context, and 3) the relationship management context. The service policy context consists of the planning methods by which a supplier analyzes its customers' logistics requirements and matches them with its own operational environment and efficiency requirements. The main conclusion related to the service policy context is that it is important to have a balanced selection of both customer-related and supplier-related factors in the analysis. This way, while the operational efficiency is planned a sufficient level of service for the most important customers is assured. This kind of policy planning involves taking multiple variables into the analysis, and there is a need to develop better tools for this purpose. Some new approaches to deal with this are presented in the thesis.The process coordination context and the relationship management context deal with the issues of how the implementation of the planned service policies can be facilitated in an inter-organizational environment. Process coordination includes typically such mechanisms as control rules, standard procedures and programs, but inhighly demanding circumstances more integrative coordination mechanisms may be necessary. In the thesis the coordination problems in third-party logistics relationship are used as an example of such an environment. Relationship management deals with issues of how separate companies organize their relationships to improve the coordination of their common processes. The main implication related to logistics planning is that by integrating further at the relationship level, companies can facilitate the use of the most efficient coordination mechanisms and thereby improve the implementation of the selected logistics service policies. In the thesis, a case of a logistics outsourcing relationship is used to demonstrate the need to address the relationship issues between the service provider andthe service buyer before the outsourcing can be done.The dissertation consists of eight research articles and a summarizing report. The principal emphasis in the articles is on the service policy planning context, which is the main theme of six articles. Coordination and relationship issues are specifically addressed in two of the papers.

Balancing effluent quality, economic cost and greenhouse gas emissions during the evaluation of (plant-wide) control/operational strategies in WWTPs

The objective of this paper was to show the potential additional insight that result from adding greenhouse gas (GHG) emissions to plant performance evaluation criteria, such as effluent quality (EQI) and operational cost (OCI) indices, when evaluating (plant-wide) control/operational strategies in wastewater treatment plants (WWTPs). The proposed GHG evaluation is based on a set of comprehensive dynamic models that estimate the most significant potential on-site and off-site sources of CO2, CH4 and N2O. The study calculates and discusses the changes in EQI, OCI and the emission of GHGs as a consequence of varying the following four process variables: (i) the set point of aeration control in the activated sludge section; (ii) the removal efficiency of total suspended solids (TSS) in the primary clarifier; (iii) the temperature in the anaerobic digester; and (iv) the control of the flow of anaerobic digester supernatants coming from sludge treatment. Based upon the assumptions built into the model structures, simulation results highlight the potential undesirable effects of increased GHG production when carrying out local energy optimization of the aeration system in the activated sludge section and energy recovery from the AD. Although off-site CO2 emissions may decrease, the effect is counterbalanced by increased N2O emissions, especially since N2O has a 300-fold stronger greenhouse effect than CO2. The reported results emphasize the importance and usefulness of using multiple evaluation criteria to compare and evaluate (plant-wide) control strategies in a WWTP for more informed operational decision making

Operational parameters of soybean seeding in santa fe system

The use of no tillage system associated with the crop-livestock integration is an alternate managing that promotes the accumulation of dry matter in the soil, an essential fact to make the system sustainable and profitable. The aim of this study was to evaluate the operational performance of a planter-tractor set on maize straws intercropped with Urochloa, in different seeding modes. The soybean crop was seed on the intercropping of two forage species (Urochloa brizantha and Urochloa ruziziensis) in five cropping systems: MBL (Maize with Urochloa in the maize seeding row, mixed with base fertilizer and deposited at 0.10 m), MBE (Maize with Urochloa seeded between rows at the same day of seeding maize), MBC (Urochloa between rows of maize seeded with the covering fertilizer at the V4 stage), MBLA (Maize with Urochloa by broadcast seeding at the V4 stage ) and MS (Single Maize: control). The following variables were evaluated: dry mass of maize straw, dry mass of forages and total dry mass of straw; and for the operational parameters the speed of seeding, wheel slippage, traction force and average power at the drawbar. The results showed that the amount of straw produced by maize intercropping with Urochloa, interferes in the operational performance of the tractor-planter at the operation of soybean seeding, i.e., areas with higher amount of straw promote greater energy demand, as well as higher wheel slippage.

Using continuous ground-based radar and lidar measurements for evaluating the representation of clouds in four operational models

The ability of four operational weather forecast models [ECMWF, Action de Recherche Petite Echelle Grande Echelle model (ARPEGE), Regional Atmospheric Climate Model (RACMO), and Met Office] to generate a cloud at the right location and time (the cloud frequency of occurrence) is assessed in the present paper using a two-year time series of observations collected by profiling ground-based active remote sensors (cloud radar and lidar) located at three different sites in western Europe (Cabauw. Netherlands; Chilbolton, United Kingdom; and Palaiseau, France). Particular attention is given to potential biases that may arise from instrumentation differences (especially sensitivity) from one site to another and intermittent sampling. In a second step the statistical properties of the cloud variables involved in most advanced cloud schemes of numerical weather forecast models (ice water content and cloud fraction) are characterized and compared with their counterparts in the models. The two years of observations are first considered as a whole in order to evaluate the accuracy of the statistical representation of the cloud variables in each model. It is shown that all models tend to produce too many high-level clouds, with too-high cloud fraction and ice water content. The midlevel and low-level cloud occurrence is also generally overestimated, with too-low cloud fraction but a correct ice water content. The dataset is then divided into seasons to evaluate the potential of the models to generate different cloud situations in response to different large-scale forcings. Strong variations in cloud occurrence are found in the observations from one season to the same season the following year as well as in the seasonal cycle. Overall, the model biases observed using the whole dataset are still found at seasonal scale, but the models generally manage to well reproduce the observed seasonal variations in cloud occurrence. Overall, models do not generate the same cloud fraction distributions and these distributions do not agree with the observations. Another general conclusion is that the use of continuous ground-based radar and lidar observations is definitely a powerful tool for evaluating model cloud schemes and for a responsive assessment of the benefit achieved by changing or tuning a model cloud

Selection of operational parameters for the production of instant soy protein isolate by pulsed fluid bed agglomeration

The objective of this study was to select the optimal operational conditions for the production of instant soy protein isolate (SPI) by pulsed fluid bed agglomeration. The spray-dried SPI was characterized as being a cohesive powder, presenting cracks and channeling formation during its fluidization (Geldart type A). The process was carried out in a pulsed fluid bed, and aqueous maltodextrin solution was used as liquid binder. Air pulsation, at a frequency of 600 rpm, was used to fluidize the cohesive SPI particles and to allow agglomeration to occur. Seventeen tests were performed according to a central composite design. Independent variables were (i) feed flow rate (0.5-3.5 g/min), (ii) atomizing air pressure (0.5-1.5 bar) and (iii) binder concentration (10-50%). Mean particle diameter, process yield and product moisture were analyzed as responses. Surface response analysis led to the selection of optimal operational parameters, following which larger granules with low moisture content and high process yield were produced. Product transformations were also evaluated by the analysis of size distribution, flowability, cohesiveness and wettability. When compared to raw material, agglomerated particles were more porous and had a more irregular shape, presenting a wetting time decrease, free-flow improvement and cohesiveness reduction. (C) 2010 Elsevier B.V. All rights reserved.

Operational parameters of soybean seeding in santa fe system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A modified Primal-Dual Logarithmic-Barrier Method for solving the Optimal Power Flow problem with discrete and continuous control variables

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The sugar cane vegetal residues unloaded in the sugar mill: Operational costs and physical characteristics

Brazil produced in 2002/03 season 317.87×106tons of sugar cane stalks and 36.88×106tons of vegetal residues (green leaves, dry leaves and tops) in a planted area of 4.61×106 hectares (ha). These residues have a useful heat of 3,613.14Mcal.t-1. Currently most of this biomass is burned as a pre-harvest practice. The doubt persists in the system type that it must be adopted to pick up, load, transport and unload this biomass at the sugar mill boilers. This study analyzed 22 variables related to operational costs and physical characteristics of these residues in a field situation using a JOHN DEERE® 6850 forage harvester with two different treatments: T1 and T2 (two types of rakes) with 6 repetitions each one. The geographic location of the studied area that belongs to COSTA PINTO MILL (COSAN® Group) is: Latitude 22°40'30S and Longitude 47°36'38W. The adopted methodology was proposed by Ripoli et al. (2002). The obtained results at a 5% level of significance showed that both treatments did not differed significantly between them. Some of the results were, where EBP stands for Oil Equivalent Barrel: Windrowing (T1=US$0.17.EBP-1 and US$9.59.ha-1, T2=US$0.08.EBP-1 and US$4.27.ha-1); Pick up (T1=US$1.31.EBP-1 and US$44.29.ha-1, T2 =US$1.37.EBP-1 and US$48.36.ha-1); Transportation (T1=US$1.27.EBP-1 and US$14,30.ha -1, T2=US$1.33.EBP-1 and US$14,80.ha -1), Unloading at the sugar mill (T1=US$0.30.EBP-1 and US$3.39.ha-1, T2=US$0.32.EBP-1 and US$3.51.ha-1); Total (T1=US$3.05.EBP-1 and US$71.57.ha-1, T2=US$3.10.EBP-1 and US$70.94.ha-1). Confronting the obtained data with the ones in the bibliography, this system revealed itself more expensive than the baling system or the integral harvest system using combines.