Preparation and characterization of gas-filled liposomes:Can they improve oil recovery?

Although well known for delivering various pharmaceutical agents, liposomes can be prepared to entrap gas rather than aqueous media and have the potential to be used as pressure probes in magnetic resonance imaging (MRI). Using these gas-filled liposomes (GFL) as tracers, MRI imaging of pressure regions of a fluid flowing through a porous medium could be established. This knowledge can be exploited to enhance recovery of oil from the porous rock regions within oil fields. In the preliminary studies, we have optimized the lipid composition of GFL prepared using a simple homogenization technique and investigated key physico-chemical characteristics (size and the physical stability) and their efficacy as pressure probes. In contrast to the liposomes possessing an aqueous core which are prepared at temperatures above their phase transition temperature (Tc), homogenization of the phospholipids such as 1,2-dipalmitoyl-sn-glycero-3- phosphocholine (DPPC) or 1,2-distearoyl-sn-glycero-3-phosphocoline (DSPC) in aqueous medium below their Tc was found to be crucial in formation of stable GFL. DSPC based preparations yielded a GFL volume of more than five times compared to their DPPC counter part. Although the initial vesicle sizes of both DSPC and DPPC based GFL were about 10 μm, after 7 days storage at 25°C, the vesicle sizes of both formulations significantly (p < 0.05) increased to 28.3 ± 0.3 μm and 12.3 ± 1.0 μm, respectively. When the DPPC preparation was supplemented with cholesterol at a 1:0.5 or 1:1 molar ratio, significantly (p < 0.05) larger vesicles were formed (12-13 μm), however, compared to DPPC only vesicles, both cholesterol supplemented formulations displayed enhanced stability on storage indicating a stabilizing effect of cholesterol on these gas-filled vesicles. In order to induce surface charge on the GFL, DPPC and cholesterol (1: 0.5 molar ratio) liposomes were supplemented with a cationic surfactant, stearylamine, at a molar ratio of 0.25 or 0.125. Interestingly, the ζ potential values remained around neutrality at both stearylamine ratios suggesting the cationic surfactant was not incorporated within the bilayers of the GFL. Microscopic analysis of GFL confirmed the presence of spherical structures with a size distribution between 1-8 μm. This study has identified that DSPC based GFL in aqueous medium dispersed in 2% w/v methyl cellulose although yielded higher vesicle sizes over time were most stable under high pressures exerted in MRI. Copyright © Informa Healthcare USA, Inc.

Impacts of oil exploration and exploitation activities on marine environment

Iran possess huge oil reservoir and occupies second place in OPEC. Recent investigation has revealed that reservoir capacity in the country amount to 60 billion barrel of oil. Many measures has been carried out to increase production capacity of oil fields to 4.2 million barrel per day. Thus any distribution in oil exploration may leave adverse effects on social and economic activities. Unfortunately due to absence of a comprehensive CPM on environmental impact assessment, lots of environmental distribution has been occurred in land and off-shore. It is well known that implementation of EIA can reduce environmental hazards. In the present investigation, all major and minor activities associated with oil exploration is identified and subsequently their effects on physical, chemical and biological environment (aquatic) has been brought out. In this context, economical, social and cultural effects of marine oil exploration is also discussed. Subsequently, all methods of EIA were studied and best mitigation plans were drawn up both for exploitation and exploration phases.

A novel continuous time representation for the scheduling of pipeline systems with pumping yield rate constraints

Pipeline systems play a key role in the petroleum business. These operational systems provide connection between ports and/or oil fields and refineries (upstream), as well as between these and consumer markets (downstream). The purpose of this work is to propose a novel MINLP formulation based on a continuous time representation for the scheduling of multiproduct pipeline systems that must supply multiple consumer markets. Moreover, it also considers that the pipeline operates intermittently and that the pumping costs depend on the booster stations yield rates, which in turn may generate different flow rates. The proposed continuous time representation is compared with a previously developed discrete time representation [Rejowski, R., Jr., & Pinto, J. M. (2004). Efficient MILP formulations and valid cuts for multiproduct pipeline scheduling. Computers and Chemical Engineering, 28, 1511] in terms of solution quality and computational performance. The influence of the number of time intervals that represents the transfer operation is studied and several configurations for the booster stations are tested. Finally, the proposed formulation is applied to a larger case, in which several booster configurations with different numbers of stages are tested. (C) 2007 Elsevier Ltd. All rights reserved.

Estudo da corrosão dos aços AISI 1010 e AISI 316L em soluções com elevado teor de cloreto e em ácido naftênico

A mudança no mercado global do petróleo nos últimos anos, com o declínio das reservas de óleo leve, têm forçado a busca por novos campos petrolíferos em ambientes mais remotos, como nos campos localizados na camada pré-sal, e a exploração de óleos pesados que possuem elevado teor de ácidos naftênicos. Isso acarreta em grandes desafios para a previsão do desempenho de materiais frente às novas condições ambientais em que estão inseridos. No presente trabalho, o comportamento da corrosão do aço carbono AISI 1010 e do aço inoxidável AISI 316L foi estudado em soluções aquosas com elevado teor de cloreto e em solução de ácido naftênico ciclopentanóico a fim de ter melhor entendimento da ação dessas espécies no processo de corrosão e simular a corrosão pela água de produção na indústria petrolífera. Foram aplicadas as técnicas de potencial de circuito aberto, polarização potenciodinâmica, voltametria cíclica, espectroscopia de impedância eletroquímica, espectroscopia Raman, microscopia eletrônica de varredura e microscopia de força atômica, usadas, em cada caso, de acordo com a conveniência. O aumento da [Cl-] na faixa de 1,2–2,8 mol.L-1 não altera os processos catódicos e anódicos perto do Ecorr para os aços AISI 1010 e AISI 316L. Em condições de sobrepotenciais afastados do Ecorr, o aumento de [Cl-] aumenta os processos oxidativos de corrosão, o que é expresso pelas maiores densidades de corrente e carga anódica e aumento da perda de massa sofrida pelos eletrodos de ambos os aços. Portanto, os danos da corrosão são mais intensos quando se aumenta a [Cl-]. O aço AISI 1010 é ativo nas soluções de NaCl e a corrosão se propaga livremente de forma uniforme. Para o aço AISI 316L, uma ampla faixa de passividade pode ser vista nas soluções de NaCl; no Epit ocorre a ruptura do filme passivo e o crescimento de pites estáveis. Após 24 h de imersão em soluções de sulfato de sódio (branco) e de ácido naftênico ciclopentanóico ocorre crescimento de filme de óxido e as fases α-Fe2O3, Fe3O4 e δ-FeO(OH) foram identificadas nos espécimes de aço AISI 1010 e Fe3O4 foi identificado nos defeitos do filme prévio presente na superfície do aço AISI 316L. Os filmes formados em solução de ácido ciclopentanóico possuem menor resistência à polarização, maior rugosidade e maior taxa de corrosão quando comparado aos filmes crescidos na solução branco, para ambos os aços. A presença do ácido naftênico muda a forma como a reação de corrosão se procede e contribui para o aumento da corrosão. A corrosão naftênica foi mais pronunciada no aço carbono porque a presença dos elementos de liga no aço inox reduzem o número de sítios ativos ricos em Fe e tornam menos oportuna a ligação do Fe com o naftenato.

Deeper insights into SRB-driven biocorrosion mechanisms

Dissertação para obtenção do Grau de Doutor em Química Sustentável

Elf ERAP en Irak, de 1968 à 1977

Dès sa création en 1966, l’ERAP s’est fixé pour but d’accroître la production du pétrole « franc », en diversifiant ses sources d’approvisionnement. Un tel objectif prend une tournure cruciale dès lors que les rapports tendus entre le groupe français et les autorités algériennes semblent menacer ses acquis dans le Sahara. Toutefois, se tailler une place sur le marché mondial semble à cette époque une tâche ardue, voire improbable, puisque les espaces les plus pétrolifères sont déjà occupés par les grandes sociétés, dites Majors. Néanmoins, la société d’État française réussit à s’implanter dans plusieurs pays producteurs, dont l’Irak en 1968, jusqu’alors considéré comme la chasse gardée de la Compagnie française des pétroles (CFP). Aussi, l’expérience irakienne, suite à l’insuccès en Algérie, incite Elf ERAP à se concentrer dans les pays pétroliers de l’Afrique subsaharienne et en Mer du Nord. Le 3 février 1968, Elf ERAP signe un accord avec la compagnie d’État pétrolière, INOC, pour se charger de la prospection et de l’exploitation d’une partie du territoire confisqué par l’État irakien à la puissante Iraq Petroleum Company (IPC). En contrepartie de ses apports financiers et techniques, Elf ERAP sera rémunérée par un approvisionnement garanti en pétrole irakien : il s’agit d’un nouveau genre de partenariat, dit « contrat d’agence ». Ce dernier succède au système classique des concessions et vaut à la société d’État un franc succès dans son projet de pénétration au Moyen Orient. Très vite, les prospections donnent lieu à la découverte de gisements. La production démarre en 1976 et s’élève à 5 millions de tonnes en 1977. Dès lors, Elf ERAP, devenue la SNEA, peut envisager avec optimisme son avenir énergétique, puisque sa sécurité d’approvisionnement est, en partie, assurée par le marché irakien. Mais, contre toute attente, le groupe d’État français se retire de l’affaire en mai 1977, laissant place à l’INOC, qui prend en charge le projet deux ans avant la date prévue par le contrat initial de 1968. Ce sujet de recherche consiste à éclaircir le rôle d’opérateur joué par l’ERAP en Irak, entre 1968 et 1977. Pour tenter d’expliquer le départ prématuré d’Elf Irak, il nous faut identifier les facteurs endogènes et exogènes qui ont pu motiver une telle décision. Autrement dit, la société d’État aurait-elle subi les revers de ses propres choix énergétiques ou un tel dénouement serait-il imputable à la politique pétrolière irakienne? Quelles sont les implications de la conjoncture pétrolière internationale dans le cas d’un tel retrait? Aidée des archives historiques d’Elf et de TOTAL, nous sommes arrivée à la conclusion que la compression du marché pétrolier, entre distributeurs et producteurs, au cours des années 1970, a considérablement nui à la rentabilité des contrats intermédiaires du type agence.

Günter Strauss e a Colecção de Minerais do Museu Mineiro do Louzal

Günter Strauss is Ph.D. in geology from the University of Munich in 1965. He is a German living by long time in Spain. Naw he is a SAPEC High Advisser His doctoral thesis, submitted in 1965, with the title "About the Geology of the Province of pyrite Southwest of the Iberian Peninsula and its oil fields, especially in the pyrite mine Louzal - Portugal" Systematized the term" Iberian Pyrite Belt ", called for the deposits of iron ore cuprífera, rich in sulfur and other metallic minerals, which occurs between the rivers Sado and Guadalquivir, where they settled several mining complexes, of Louzal, Rio Tinto, through Castro Verde, Santo Domingo and Tharsis. Local mining tradition with an ancient where today seeks to preserve the legacy and memory of mining through measures to enhance equity. The result of work carried out Louzal then formed the basis of geological and documentary collection that has survived and has been proposed for cultural units under the activities of the mining museum Louzal. The richness and importance of this collection, consisting of several hundred documents, geological samples classified, minerals and cartography, comes from its presence Situ"In its state of preservation, that despite the various threats it is still within reach of their preservation, and the relative rarity of such collections, with the units of mining production. This communication aims to reveal the contribution of Mr Strauss for the formation of this collection and submit his proposal for cultural units, with the hope that those responsible for safeguarding them understand the need for its preservation and dissemination. So discuss the scientific and professional way Günter Strauss, a geologic formation of the estate of Mines Louzal, and the draft musealization proposition.

Adição de superplastificante e anti-segregante à base de CMC em pastas de cimento para Poços de Petróleo

Oil well cementing materials consist of slurries of Special class Portland cement dispersed in water. Admixtures can be used to provide the necessary fluidity, so the material can be efficiently pumped down as well as penetrate porous rocks with controlled filter loss. Construction admixtures can be used to modify the properties of oil well cements provided they can withstand and hold their properties at the higher than ambient temperatures usually encountered in oil fields. In civil construction, superplasticizer play the role of dispersants that reduce the facto r of water cement improve mechanical properties and fluidity of the cement, whereas anti-segregation agents improve the workability of the slurry. In the present study, oil well cement slurries were produced adding both a dispersant and an anti-segregation agent conventionally used in Portland CPII-Z-32 RS cement aiming at materials for primary cementing and squeeze operations. Three basic aspects were evaluated: fluidity, filter loss and the synergetic effect of the admixtures at two temperatures, i.e., 27°C and 56°C, following API RP 10B practical recommendations. The slurries were prepared using admixture concentrations varying from 2.60 Kgf/m3 (0.02 gallft3) to 5.82 Kgf/m3 (0.045 galJft3) BWOC. The density of the slurries was set to 1.89 g/cm3 (15.8 Ib/gal). 0.30 to 0.60% BWOC of a CMC-based anti-segregation agent was added to the cement to control the filter loss. The results showed that the addition of anti-segregation at concentrations above 0.55% by weight of cement resulted in the increased viscosity of the folders in temperatures evaluated. The increasing the temperature of the tests led to a reduction in the performance of anti-segregation. At concentrations of 5.20 kgf/m3 (0,040 gallft3) and 5.82 Kgf/m3 (0,045 gal/ft 3) observed a better performance of the properties evaluated in the proposed system. At low temperature was observed instability in the readings of rheology for all concentrations of anti-segregation. Contents that increasing the concentration of anti¬-segregation is limited concentrations greater than 0.55 % BWOC of the CMC in temperature analyzed. The use of the system with CMC promoted a good performance against the properties evaluated. The principal function of anti¬-segregation was optimized with increasing concentration of superplasticizer, at temperatures above the 2rC. The study of the behaviour of systemic additives, resulting in slurries of cement, which can be optimized face studies of other intrinsic properties in oil fields

Influência das tensões tectônicas na permeabilidade da formação Açu - Bacia Potiguar

The behavior of the fluid flux in oil fields is influenced by different factors and it has a big impact on the recovery of hydrocarbons. There is a need of evaluating and adapting the actual technology to the worldwide reservoirs reality, not only on the exploration (reservoir discovers) but also on the development of those that were already discovered, however not yet produced. The in situ combustion (ISC) is a suitable technique for these recovery of hydrocarbons, although it remains complex to be implemented. The main objective of this research was to study the application of the ISC as an advanced oil recovery technique through a parametric analysis of the process using vertical wells within a semi synthetic reservoir that had the characteristics from the brazilian northwest, in order to determine which of those parameters could influence the process, verifying the technical and economical viability of the method on the oil industry. For that analysis, a commercial reservoir simulation program for thermal processes was used, called steam thermal and advanced processes reservoir simulator (STARS) from the computer modeling group (CMG). This study aims, through the numerical analysis, find results that help improve mainly the interpretation and comprehension of the main problems related to the ISC method, which are not yet dominated. From the results obtained, it was proved that the mediation promoted by the thermal process ISC over the oil recovery is very important, with rates and cumulated production positively influenced by the method application. It was seen that the application of the method improves the oil mobility as a function of the heating when the combustion front forms inside the reservoir. Among all the analyzed parameters, the activation energy presented the bigger influence, it means, the lower the activation energy the bigger the fraction of recovered oil, as a function of the chemical reactions speed rise. It was also verified that the higher the enthalpy of the reaction, the bigger the fraction of recovered oil, due to a bigger amount of released energy inside the system, helping the ISC. The reservoir parameters: porosity and permeability showed to have lower influence on the ISC. Among the operational parameters that were analyzed, the injection rate was the one that showed a stronger influence on the ISC method, because, the higher the value of the injection rate, the higher was the result obtained, mainly due to maintaining the combustion front. In connection with the oxygen concentration, an increase of the percentage of this parameter translates into a higher fraction of recovered oil, because the quantity of fuel, helping the advance and the maintenance of the combustion front for a longer period of time. About the economic analysis, the ISC method showed to be economically feasible when evaluated through the net present value (NPV), considering the injection rates: the higher the injection rate, the higher the financial incomes of the final project

Otimização de vazão de poços injetores em projeto de injeção de água utilizando simulação por linhas de fluxo

Until the early 90s, the simulation of fluid flow in oil reservoir basically used the numerical technique of finite differences. Since then, there was a big development in simulation technology based on streamlines, so that nowadays it is being used in several cases and it can represent the physical mechanisms that influence the fluid flow, such as compressibility, capillarity and gravitational segregation. Streamline-based flow simulation is a tool that can help enough in waterflood project management, because it provides important information not available through traditional simulation of finite differences and shows, in a direct way, the influence between injector well and producer well. This work presents the application of a methodology published in literature for optimizing water injection projects in modeling of a Brazilian Potiguar Basin reservoir that has a large number of wells. This methodology considers changes of injection well rates over time, based on information available through streamline simulation. This methodology reduces injection rates in wells of lower efficiency and increases injection rates in more efficient wells. In the proposed model, the methodology was effective. The optimized alternatives presented higher oil recovery associated with a lower water injection volume. This shows better efficiency and, consequently, reduction in costs. Considering the wide use of the water injection in oil fields, the positive outcome of the modeling is important, because it shows a case study of increasing of oil recovery achieved simply through better distribution of water injection rates

Análise de agrupamentos dos dados de DFA oriundos de perfis elétricos de indução de poços de petróleo

The main objective of this study is to apply recently developed methods of physical-statistic to time series analysis, particularly in electrical induction s profiles of oil wells data, to study the petrophysical similarity of those wells in a spatial distribution. For this, we used the DFA method in order to know if we can or not use this technique to characterize spatially the fields. After obtain the DFA values for all wells, we applied clustering analysis. To do these tests we used the non-hierarchical method called K-means. Usually based on the Euclidean distance, the K-means consists in dividing the elements of a data matrix N in k groups, so that the similarities among elements belonging to different groups are the smallest possible. In order to test if a dataset generated by the K-means method or randomly generated datasets form spatial patterns, we created the parameter Ω (index of neighborhood). High values of Ω reveals more aggregated data and low values of Ω show scattered data or data without spatial correlation. Thus we concluded that data from the DFA of 54 wells are grouped and can be used to characterize spatial fields. Applying contour level technique we confirm the results obtained by the K-means, confirming that DFA is effective to perform spatial analysis

Uma aplicação da apredizagem por reforço na otimização da produção em um campo de petróleo

The objective of reservoir engineering is to manage fields of oil production in order to maximize the production of hydrocarbons according to economic and physical restrictions. The deciding of a production strategy is a complex activity involving several variables in the process. Thus, a smart system, which assists in the optimization of the options for developing of the field, is very useful in day-to-day of reservoir engineers. This paper proposes the development of an intelligent system to aid decision making, regarding the optimization of strategies of production in oil fields. The intelligence of this system will be implemented through the use of the technique of reinforcement learning, which is presented as a powerful tool in problems of multi-stage decision. The proposed system will allow the specialist to obtain, in time, a great alternative (or near-optimal) for the development of an oil field known

Caracterização ambiental de bancos areno-lamosos nos campos petrolíferos de Macau e Serra (RN), como subsídio às medidas mitigadoras ao processo erosivo

On Rio Grande do Norte northern coast the process of sediment transport are intensely controlled by wind and sea (waves and currents) action, causing erosion and shoreline morphological instability. Due to the importance of such coastal zone it was realized the multi-spectral mapping and physical-chemical characterization of mudflats and mangroves aiming to support the mitigating actions related to the containment of the erosive process on the oil fields of Macau and Serra installed at the study area. The multi-spectral bands of 2000 and 2008 LANDSAT 5 TM images were submitted on the several digital processing steps and RGB color compositions integrating spectral bands and Principal Components. Such processing methodology was important to the mapping of different units on surface, together with field works. It was possible to make an analogy of the spectral characteristics of wetlands with vegetations areas (mangrove), showing the possibility to make a restoration of this area, contributing with the environmental monitoring of that ecosystem. The maps of several units were integrated in GIS environment at 1:60,000 scale, including the classification of features according to the presence or absence of vegetation cover. Thus, the strategy of methodology established that there are 10.13 km2 at least of sandy-muddy and of these approximately 0.89 km2 with the possibility to be used in a reforestation of typical flora of mangrove. The physical-chemical characterization showed areas with potential to introduce local species of mangrove and they had a pH above neutral with a mean of 8.4. The characteristic particle size is sand in the fine fractions, the high levels of carbonate, organic matter and major and trace element in general are concentrated where the sediment had the less particles size, showing the high correlation that those elements have with smaller particles of sediment. The application of that methodological strategy is relevant to the better understanding of features behavior and physical-chemical data of sediment samples collected on field allow the analysis of efficiency/capability of sandy-muddy to reforestation with local mangrove species for mitigation of the erosive action and coastal processes on the areas occupied by the oil industry

Pastas compósitas cimento/sílica/polímero para cimentação de poços de baixa profundidade sujeitas à injeção de vapor

The production of heavy oil fields, typical in the Northeastern region, is commonly stimulated by steam injection. High bottom hole temperatures are responsible not only for the development of deleterious stresses of the cement sheath but also for cement strength retrogression. To overcome this unfavorable scenario, polymeric admixtures can be added to cement slurries to improve its fracture energy and silica flour to prevent strength retrogression. Therefore, the objective of the present study was to investigate the effect of the addition of different concentrations of polyurethane (5-25%) to cement slurries containing 40% BWOC silica flour. The resulting slurries were characterized using standard API (American Petroleum Institute) laboratory tests. In addition to them, the mechanical properties of the slurries, including elastic modulus and microhardness were also evaluated. The results revealed that density, free water and stability of the composite cement/silica/polyurethane slurries were within acceptable limits. The rheological behavior of the slurries, including plastic viscosity, yield strength and gel strength increased with the addition of 10% BWOC polyurethane. The presence of polyurethane reduced the fluid loss of the slurries as well as their elastic modulus. Composite slurries also depicted longer setting times due to the presence of the polymer. As expected, both the mechanical strength and microhardness of the slurries decreased with the addition of polyurethane. However, at high bottom hole temperatures, the strength of the slurries containing silica and polyurethane was far superior than that of plain cement slurries. In summary, the use of polyurethane combined with silica is an interesting solution to better adequate the mechanical behavior of cement slurries to heavy oil fields subjected to steam injection

Avaliação ambiental de manguezais adjacentes aos campos petrolíferos de Macau e Serra (RN), como subsídio às medidas mitigadoras ao processo erosivo

Among the various effects caused by the climate change and human intervention, the mangrove ecosystem changes through of the years has been worth mentioning, which hasn t known which are the pros and cons for the adjacent coastal and estuarine environments yet. It happens due to the present dynamism in these areas, besides of the difficult understanding of the processes associated with evolution. This study aimed to environmentally evaluate adjacent mangroves from the Macau and Serra oil fields, located on Rio Grande do Norte northern coast, to support the mitigating actions related to the containment of the erosive process, as well as, according to the principles of the Clean Development Mechanism (CDM), to assess the amount of atmospheric carbon sequestered by the studied ecosystem. An inventory was conducted through mangrouve mapping which has supplied this research, especially regarding to the structural characterization of mangrove areas. To understand the local mangrove behavior in a greater level detail, techniques of remote sensing, GIS and GPS were used to make an analogy between the current and past states of the mangrove studied, allowing to make anticipated projections for the future impacts or changes in that region. This study combined data from multispectral LANDSAT 5 TM, Landsat 7 ETM+ with radar microwave data from SAR RADARSAT-1, which increased the interpretation capacity of the data from optical sensor systems. The interpretations have been supported by the data field, representing a better and innovative methodology for the environmental and taxonomic characterization of mangrove forests considered. The results reveal that mangroves of the Ponta do Tubarão Sustainable Development Reserve are biologically representative areas and providing a variety of benefits, especially for local communities, constituting the priority sites for actions development aimed at conservation. They also have been showing the necessity to make mitigating measures in order to recover degraded areas through reforestation or creating new areas of mangrove, as currently 7.1% of the mangrove forests studied are dead or in an advanced state of decomposition. The amount of atmospheric carbon sequestered proved very significant when analyzed for the whole area, which is able to sequester atmospheric 4,294,458 Ton CO2 per year