The real area of contact and compliance of rough cylinders in compression

Bearing area analysis has been used to study the real area of contact and compliance of rough turned steel cylinders in compression. Calculations show that the elastic real area of contact is very small compared to the plastic real area of contact, and that local compliance due to flattening of asperity tips is a small proportion of the total compliance obtained from experiments. The fact that increased load brings more and more new asperities under load rather than enlarging the contact spots leads to a rather simple load-compliance relation for a rough cylinder, viz., W' = Nh · K1δn, where W0 = K1δn defines the load-compliance relation of the individual asperities, and Nh represents the number of asperities bearing the load.

Estimation of higher natural frequencies of polar orthotropic annular plates

A method based on an assumption that the radial bending moment is zero at a nodal circle is shown to yield accurate estimates of natural frequencies corresponding to higher modes of transversely vibrating polar orthotropic annular plates for various combinations of clamped, simply supported and free edge conditions. This method is found to be convenient for the determination of locations of nodal circles as well. Numerical investigations revealed that for small holes, nodal circles tend to move towards the outer edge with increasing number of nodal diameters. For large holes, it has been shown that the plate behaves like a long rectangular strip.

real area of contact and compliance of rough cylinders in compression

Bearing area analysis has been used to study the real area of contact and compliance of rough turned steel cylinders in compression. Calculations show that the elastic real area of contact is very small compared to the plastic real area of contact, and that local compliance due to flattening of asperity tips is a small proportion of the total compliance obtained from experiments. The fact that increased load brings more and more new asperities under load rather than enlarging the contact spots leads to a rather simple load-compliance relation for a rough cylinder, viz., W' = Nh · K1δn, where W0 = K1δn defines the load-compliance relation of the individual asperities, and Nh represents the number of asperities bearing the load.

Vibration of generally orthotropic skew plates

Vibration problem of generally orthotropic plates with particular attention to plates of skew geometry is studied. The formulation is based on orthotropic plate theory with arbitrary orientation of the principal axes of orthotropy. The boundary conditions considered are combinations of simply supported, clamped, and free-edge conditions. Approximate solution for frequencies and modes is obtained by the Ritz method using products of appropriate beam characteristic functions as admissible functions. The variation of frequencies and modes with orientation of the axes of orthotropy is examined for different skew angles and boundary conditions. Features such as "crossings" and "quasi-degeneracies" of the frequency curves are found to occur with variation of the orientation of the axes of orthotropy for a given geometry of the skew plate. It is also found that for each combination of skew angle and side ratio, a particular orientation of the axes gives the highest value for the fundamental frequency of the plate.

Mass transfer with surface reaction in arrays of cylinders at low reynolds and high peclet numbers

Creeping flow hydrodynamics combined with diffusion boundary layer equation are solved in conjunction with free-surface cell model to obtain a solution of the problem of convective transfer with surface reaction for flow parallel to an array of cylindrical pellets at high Peclet numbers and under fast and intermediate kinetics regimes. Expressions are derived for surface concentration, boundary layer thickness, mass flux and Sherwood number in terms of Damkoehler number, Peclet number and void fraction of the array. The theoretical results are evaluated numerically.

A numerical method for separation of stresses in photo-orthotropic elasticity

A numerical method is suggested for separation of stresses in photo-orthotropic elasticity using the numerical solution of compatibility equation for orthotropic case. The compatibility equation is written in terms of a stress parameter S analogous to the sum of principal stresses in two-dimensional isotropic case. The solution of this equation provides a relation between the normal stresses. The photoelastic data give the shear stress and another relation between the two normal stresses. The accuracy of the numerical method and its application to practical problems are illustrated with examples.

Flow between torsionally oscillating noncoaxial cylinders

Abstract is not available.

Effect of membrane action on the plastic collapse load of circular orthotropic slabs with fixed edges

In the case of reinforced concrete slabs fixed at the boundaries, considerable enhancement in the load carrying capacity takes place due to compressive membrane action. In this paper a method is presented to analyse the effects of membrane action in fixed orthotropic circular slabs, carrying uniformly distributed loads. Depending on the radial moment capacity being greater or less than the circumferential moment capacity, two cases of orthotropy have been considered. Numerical results are worked out for certain assumed physical parameters and for different coefficients of orthotropy. Variations of load and bending moments with the central deflection are presented.

Towards stress freezing in birefringent orthotropic composite models

Birefringent composite models are fabricated using epoxy resin reinforced with unidirectionally oriented glass fibers. The mechanical and photoelastic properties of the material at room temperature are determined. To explore the possibility of application of stress-freezing technique to birefringent composite models, the behavior and properties of this material are studied at elevated temperature (at stress-freezing temperature of the resin). The properties of the material at room and at elevated temperatures are reported. The feasibility of stress freezing glass-fiber-reinforced epoxy composites with low-fiber-volume fraction is discussed.

Estimation of higher natural frequencies of polar orthotropic annular plates

A method based on an assumption that the radial bending moment is zero at a nodal circle is shown to yield accurate estimates of natural frequencies corresponding to higher modes of transversely vibrating polar orthotropic annular plates for various combinations of clamped, simply supported and free edge conditions. This method is found to be convenient for the determination of locations of nodal circles as well. Numerical investigations revealed that for small holes, nodal circles tend to move towards the outer edge with increasing number of nodal diameters. For large holes, it has been shown that the plate behaves like a long rectangular strip.

Free convection heat transfer from vertical cylinders and wires

Free convection heat transfer from vertical long cylinders and wires were investigated experimentally. The experiments were designed to check the analytical results and the radius of curvature criteria formulated by the same authors. The results for water, the fluid medium used in the present set of experiments, are in excellent agreement with the theory. The results of Hama, Recesso and Christiaens, Kyte, Madden and Piret, in air are also shown to be in close agreement with proposed correlations.

Dust Deposition on Single Cylinders

The inertial impaction of Lycopodium spores on single wires lying transverse to the direction of flow has been studied. The equations of particle motion in a potential flow field have been modified for the case when Stokes' law is inapplicable. Solutions to the above equations have been obtained by digital computation. Rec, the Reynolds number based on cylinder diameter, varied from 4 to 240; particle trajectories in a flow field at Rec = 10 have been determined for inertia parameter K = 1, 2, 4, 6, and 10. Ten trajectories were developed for the above cases by the numerical stepwise method. Experiments were performed by depositing Lycopodium spores on adhesive-coated wires of various diameters and at different velocities. The weight of dust deposited was determined with a microbalance. The experimental conditions were:. Wire diameters: 345, 457, 1500 μ. Particle diameter: 35 μ. Air velocities: 20-250 cm/sec. Inertia parameter: 1-60. The particle was considered as a point mass in the theoretical analysis. But in the experiments the ratio of particle size to wire size was not negligible (rp/rc = 0·1) and hence the effect of finite size of particle on collection efficiency due to the direct interception effect has been estimated. The effect of particle size distribution on collection efficiency has also been estimated. The experimental efficiencies obtained compare well with the calculated efficiencies at Rec = 10 when direct interception is taken into account.

Determination of the orthotropic plate parameters of stiffened plates and grillages in free vibration

It is well known that the analysis of vibration of orthogonally stiffened rectangular plates and grillages may be simplified by replacing the actual structure by an orthotropic plate. This needs a suitable determination of the four elastic rigidity constants Dx, Dy, Dxy, D1 and the mass {Mathematical expression} of the orthotropic plate. A method is developed here for determining these parameters in terms of the sectional properties of the original plate-stiffener combination or the system of interconnected beams. Results of experimental work conducted on aluminium plates agree well with the results of the theory developed here.

Bending, vibration and buckling of simply supported thick orthotropic rectangular plates and laminates

This paper presents a unified exact analysis for the statics and dynamics of a class of thick laminates. A three-dimensional, linear, small deformation theory of elasticity solution is developed for the bending, vibration and buckling of simply supported thick orthotropic rectangular plates and laminates. All the nine elastic constants of orthotropy are taken into account. The solution is formally exact and leads to simple infinite series for stresses and displacements in flexure, forced vibration and "beam-column" type problems and to closed form characteristic equations for free vibration and buckling problems. For free vibration of plates, the present analysis yields a triply infinite spectrum of frequencies instead of only one doubly infinite spectrum by thin plate theory or three doubly infinite spectra by Reissner-Mindlin type analyses. Some numerical results are presented for plates and laminates. Comparison of results from thin plate, Reissner and Mindlin analyses with these yield some important conclusions regarding the validity and effects of the assumptions made in the approximate theories.

Vibration of rectangular orthotropic plates

An approximate analytical procedure has been given to solve the problem of a vibrating rectangular orthotropic plate, with various combinations of simply supported and clamped boundary conditions. Numerical results have been given for the case of a clamped square plate. Nomenclature 2a, 2b sides of the rectangular plate h plate thickness Eprime x , Eprime y , EPrime, G elastic constants of te orthotropic material D x Eprime x h 3/12 D y Eprime y h 3/12 H xy EPrimeh 3/12+Gh 3/6 D x , D y and H xy are rigidity constants of the orthotropic platergr mass of the plate per unit area ngr Poisson's ratio W deflection of the plate p circular frequency gamma b/a ratio X m , Y characteristic functions of the vibrating beam problem -lambda rgrp 2 a 2 b 2/H xy the frequency parameter.