Desenvolvimento de metodologias para a determinação da atividade biogênica de bactérias redutoras de sulfato

A corrosão causada por H2S biogênico frequentemente resulta em danos extensos na indústria do petróleo. O presente trabalho avaliou parâmetros de crescimento microbiano e aplicou metodologias de determinação de sulfetos por técnicas espectrofotométrica na região da luz visível e radiorespirométrica para avaliação da atividade metabólica, correlacionando com a população de bactérias redutoras de sulfato, determinada através da técnica do Número Mais Provável (NMP). Amostras de água de formação e consórcio de BRS foram avaliadas através do arraste de sulfetos estáveis produzidos biogenicamente e quantificados por espectrofotometria. O cálculo das velocidades instantâneas e específicas de produção de sulfetos permitiu avaliar de que maneira alguns parâmetros de crescimento microbiano podem afetar o metabolismo das BRS. A detecção de concentrações traço de sulfetos biogênicos pode ser realizada através de ensaios radiorespirométricos. Para isto, diluições em série de água do mar sintética com três amostras distintas foram avaliadas. Os testes realizados indicam que o acréscimo do tempo de incubação de cultura microbiana anaeróbia mista contribuiu para o aumento das capacidades de redução de sulfato, assim como o aumento das fontes de carbono. Ambas as técnicas provaram ser um rápido teste para a detecção de sulfetos biogênicos, particularmente aqueles associados aos produtos de corrosão, sendo uma ferramenta muito útil para monitoração e controle de tanques de armazenamento de água e óleo, plataformas continentais de petróleo e diversos tipos de reservatórios. O presente trabalho prevê a continuidade dos experimentos, através de avaliação de um maior universo de amostras da indústria do petróleo e medições menos espaçadas da técnica espectrofotométrica, além da avaliação radiorespirométrica em modo contínuo, evitando os efeitos inibitórios do H2S

制革废水生物强化处理及中水回用试验研究

制革行业是轻工行业中仅次于造纸业的高耗水、重污染行业，作为劳动密集型行业，在解决大量人口就业问题的同时，也对所在地区环境造成了严重污染。目前我国制革行业每年排放废水8,000~12,000万吨，废水中含铬约3,500 t，SS为1.2×105 t，COD为1.8×105 t，BOD为7×104 t，对水体污染严重。 本研究在对厌氧酸化工艺进行研究、一级好氧处理段进行工艺比选研究的基础上，获得了匀质调节—SBBR—BAF的生物处理工艺，并依托该工艺进行了生物强化处理的研究，考察了菌剂的强化运行效果及其处理水回用的可行性。 研究表明，在进水COD＞3,000 mg/L，厌氧酸化具有很好的抗冲击作用，保证了好氧工艺出水COD＜200 mg/L；在进水COD＜3,000 mg/L，可只通过好氧处理实现出水COD＜200 mg/L。厌氧酸化停留时间选择不当，会导致厌氧出水硫化物浓度升高，严重影响好氧系统，会使好氧活性污泥因中毒而解絮。 研究表明，当进水COD为2,000~2,500 mg/L，NH4+-N为130~146 mg/L时，COD、NH4+-N去除率SBBR分别为93.8%~96.6%和14.5%~55.9%，SBR分别为88.8%~94.9%和13%~50.7%，表明SBBR优于SBR。同时，研究发现SBBR污泥增长率为0.05 kgVSS/kgCOD，仅为SBR0.57 kgVSS/kgCOD的8.8%。此外，研究发现SBBR在停止运行后经3个运行周期可回复原油能力，而SBR池经9个周期培养也不能恢复，说明SBBR恢复能力明显优于SBR。 研究表明，以匀质调节—SBBR—BAF为主的制革废水处理工艺，出水水质稳定，进水COD 801~2,834 mg/L、NH4+-N 87~203 mg/L，出水COD＜80 mg/L、NH4+-N＜10 mg/L，基本达到中水回用标准；操作简单灵活，没有污泥回流系统，污泥产率低，污泥处理费用低；工艺基本不需要添加化学药剂，既节约成本、又避免了二次污染；两级生物膜使得该工艺具有很强的耐冲击负荷能力，特别适合制革废水水质水量波动大的特点。 研究表明，高效菌对系统的启动具有一定的促进作用，强化系统生物膜6天可以成熟，对照系统生物膜9天可以成熟。同时高效菌能加速COD降解，缩短停留时间，强化系统6~8 h可使COD＜200 mg/L，对照系统8~10 h可使COD＜200 mg/L。长期运行表明，强化系统的SBBR在COD和NH4+-N的去除率都优于对照系统的SBBR。最终出水COD强化系统平均为53 mg/L、对照系统为74 mg/L。在模拟循环过程中，强化系统均有更高的稳定性。可实现8次理论循环，而对照系统只能实现4次理论循环。 研究表明，通过合理的工艺设计，可以实现猪皮制革废水达到《污水综合排放标准GB8976-1996》一级标准，同时满足工厂部分用水要求。通过添加高效微生物，可提高生物处理系统处理能力，使处理水能够满足工厂的多次回用。 As a labour-intensive industry, tanning has created large amount of working opportunities as well as caused severe contamination to environment. And it is one of the highest water-consuming and polluting industry, only second to manufacturing. At present time, Chinese leather industry emits wastewater about 80,000,000~120,000,000 t annually, which contains chromium about 3,500 t, SS 1.2×105 t, COD 1.8×105 t, BOD 7×104 t and ambient riverhead has been polluted greatly. Based on the research of anaerobic acidification and comparison of SBBR and SBR, biotreatment process (Homogenization—SBBR—BAF) had been established to amend the disadvantages of traditional sewage treatment such as too much sludge, high cost of advanced treatment and NH4+-N can not reach the emission standard. Research on the bioaugmentation was also been carried out. Researches showed, when COD of influent was beyond 3,000 mg/L, anaerobic acidification could resist strong impact, thus COD of effluent was less than 200 mg/L; when COD of influent was less than 3,000 mg/L, only throughout aerobic sewage treatment could COD of effluent beless than 200 mg/L. False residence tiome of anaerobic acidification would lead to the higher effluent concentration of sulfide and disintegration of aerobic activated sludge. Researches showed SBBR worked a better than SBR: when influent between 2,000 and 2,500 mg/L, NH4+-N between 130 mg/L and 146 mg/L, COD, NH4+-N removal rate of SBBR was 93.3%~96.6%, 14.5%~55.9% respectively while COD, NH4+-N removal rate of SBR was 88.8%~94.9%, 13%~50.7% respectively. Sludge growth rate of SBBR was 8.8% of that of 0.05 kgVSS/kgCOD. Besides, SBBR could recovered after 3 operating periods while SBR worked no better after 9 operating periods.Therefore, SBBR excelled SBR. Researches showed, effluent quantity of tannery wastewater treatment process (Homogenization—SBBR—BAF) was stable. When COD of influent was between 801 and 2,834 mg/L, NH4+-N was between 87 mg/L and 203 mg/L, COD of effluent was less than 80 mg/L, NH4+-N was less than 10 mg/L, which achieved the standard of reuse. This biotreatment was featured in low cost, easy and flexible management, less sludge, no inverse sludge system. Besides, this technique required no chemical, which could lower the cost and avoid secondary pollution. Great resistant of impact due to two membranes and was suitable for tannery wastewater which was featured by fluctuation of influent quality and quantity. Researches showed effective microorganisms promotes the startup of the process.Biofilm in the bioaugmentation process matured with 6 days while biofilm in normal process matured with 9 days. Effective microorganisms could accelerate the degradation of COD and shorten the residence time. Aggrandizement system could make COD<200 mg/L with 6 to8 hours while cntrolling system could make COD<200 mg/L with 8 to 10 hours. Long-term operating shows that SBBR in the bioaugmentation system worked better than the normal system in the treatment of COD and NH4+-N. The average COC of effluent in bioaugmentation system was 53 mg/L, normal system was 74 mg/L. In the simulative circulation process,aggrandizement process, which could fulfill 8 times theoretical circulation, works more stably than controlling process which could only fulfill 4 times theoretical circulation. Researches showed that reasonable design could make the wastewater meet the first grade of discharging standard of National Integrated Wastewater Discharge Standard (GB8976-1996), and partially meet the demand of water using of the factory. Adding effective microorganisms could enhance the biotreatment and make the effluents reuse many times.

Applications of cardanol in rubber processing

This research project explores the utilization of cardanol in various capacities for rubber processing. Cardanol is a phenol with a long side chain in the meta position of the benzene ring. It is obtained by the vacuum distillation of cashew Hut shell liquid (CNSL) which is a cheap agro-byproduct. In this study, the plasticizer property of cardanol was investigated in silica filled and HAF black filled NR, NBR, EPDM and CR by comparing cure characteristics and mechanical properties of vulcanizates containing conventional plasticizer with those containing cardanol as plasticizer. The co-activator, antioxidant and accelerator properties were investigated in gum samples of NR, NBR, EPDM and CR by comparing the properties of vulcanizates which contain conventional co-activator, antioxidant and accelerator with those in which each of them was replaced by cardanol. The general effectiveness of cardanol was investigated by determination of cure time , measurement of physical and mechanical properties, ageing studies, crosslink density, extractability, FTIR spectra, TGA etc.The results show that cardanol can be a substitute for aromatic oil in both silica filled and HAF black filled NR. Again, it can replace dioctyl phthalate in both silica filled and HAF black filled NBR. Similarly, cardanol Can replace naphthenic oil in silica filled as well as HAF black filled EPDM and CR. The cure characteristics and mechanical properties are comparable in all the eight cases. The co-activator property of cardanol is comparable to stearic acid in all the four rubbers. The cure characteristics and mechanical properties in this case are also comparable. The antioxidant ,property of cardanol is comparable to TQ in all the four rubbers. The antioxidant property of cardanol is comparable to TQ in all the four case of NBR and EPDM.The accelerator property of cardarlol is comparable with CBS in the case of NBR and EPDM. No accelerator property is observed in the case of NR. The accelerator property of cardanol in CR is not negligible when compared with TMTD.

Beneficiamentos da cinza de casca de arroz residual com vistas à produção de cimento composto e/ou pozolânico

A cinza de casca de arroz é um resíduo agro-industrial decorrente do processo de queima da casca de arroz, sendo largamente encontrada no Rio Grande do Sul, pois, historicamente, este Estado é o maior produtor de arroz no Brasil, com cerca de 45% da produção nacional. Empregada como fonte de energia, a casca de arroz é queimada em diversas empresas; algumas, devido à sua natureza, incorporam a cinza ao produto, mas a maioria não encontra outro destino que não o descarte em forma de aterro, criando, assim, um problema ambiental de poluição do solo, do ar e de rios e córregos. No entanto, devido à presença de elevado percentual de sílica (SiO2) na sua constituição, a cinza de casca de arroz pode ter vários empregos. Na construção civil, pode ser empregada como pozolana, conforme vários estudos já vêm demonstrando. Porém, encontra restrições por motivos como sua cor escura, que confere aos cimentos, argamassas e concretos aos quais é adicionada, uma coloração também escura, e a falta de uniformidade apresentada em termos de características químicas e, principalmente, mineralógicas. A cor escura não é um problema de ordem técnica, mas estética e de aceitação no mercado. Já a composição mineralógica está associada à atividade pozolânica e a falta de uniformidade do material disponível implica na incerteza do grau de reatividade. Este trabalho teve o objetivo de verificar a viabilidade técnica do emprego de cinzas de casca de arroz residuais na confecção de cimentos Portland composto e/ou pozolânico, a partir de beneficiamentos das mesmas, que associam tratamentos físicos, químicos e/ou térmicos, os quais têm como finalidade reverter e/ou minimizar os aspectos negativos citados. Para tanto, foram empregadas três cinzas de casca de arroz, oriundas de diferentes processos de produção e com composições mineralógicas distintas. Após definidos os tratamentos a serem aplicados, através de seleção pelos critérios de cor e composição mineralógica, as cinzas tratadas foram avaliadas quanto à sua pozolanicidade, pelo Índice de Atividade Pozolânica (IAP) da NBR 5752 e também por um IAP alterado, proposto neste trabalho. A produção de cimentos com CCA beneficiada se deu a partir de um cimento base com substituição por CCA, em massa e em diferentes percentuais. Tais cimentos foram avaliados quanto à resistência à compressão, aos tempos de pega, à pozolanicidade e à expansibilidade a quente. A análise dos dados obtidos indica que os tratamentos propostos e/ou a associação deles resultam em beneficio no desempenho das cinzas, em pelo menos um dos vários aspectos considerados. A presente pesquisa permite concluir que as CCA residuais têm potencial para serem empregadas na produção de cimentos, tanto aquelas menos cristalinas, quanto as mais cristalinas. Para tanto, devem ser beneficiadas, sendo pelo menos submetidas a tratamento físico para redução de sua granulometria. Se outros objetivos forem pretendidos, como coloração clara, os tratamentos térmico ou químico podem ser empregados.

Estudo da potencialidade da incorporação de resíduo de granito e da queima da casca do café em cerâmica vermelha

The industrial production of ornamental rocks and the burning of coffee husk generate waste that is discarded into the environment. However, with the study of the incorporation of these residues in ceramic products, may be found an alternative to reducing environmental impacts and detrimental effects on human health caused by its indiscriminate disposal of waste in nature. Thus, this work aimed to study the addition of ashes of the coffee husk and granite residue in matrix of red ceramic. The raw materials were dry milled and sieved to mesh 100. To characterize the raw materials were carried out analyzes of X-ray diffraction (XRD), X-ray fluorescence (XRF), particle size analysis (PSA), differential thermal analysis (DTA) and thermogravimetric analysis (TG). Six formulations were prepared where the clay content was kept constant (70%wt) and ashes contents and granite residue varied from 10, 15, 20 and 30%. Dilatometrics analyzes were performed at four selected formulations, containing them: 100% clay (A100); 70% clay and 30% ashes (A70C30); 70% clay and 30% granite residue (A70G30); and 70% clay, 15% granite residue and 15% ashes (A70G15C15). The samples were prepared by uniaxial compaction with pressure of 25 MPa, and fired at temperatures of 800°C, 850ºC, 900ºC, 950ºC, 1000ºC and 1100°C. Assays were performed to determine the linear shrinkage of burning (LSB), water absorption (WA), apparent porosity (AP), density (D) and tensile bending. Also were performed analyzes of X-ray diffraction (XRD) and scanning electron microscopy (SEM) of the samples fired. The formulations incorporating granite residue and/or ashes reached the required limits of water absorption according to NBR 15270-1 and NBR 15310 and tensile bending according to classical literature (SANTOS, 1989) necessary for the production of tiles and ceramic block for masonry sealing

Análise das emissões gasosas de um veículo flex funcionando com diferentes combustíveis

Efforts in research and development of new technologies to reduce emission levels of pollutant gases in the atmosphere has intensified in the last decades. In this context, it can be highlighted the modern systems of electronic engine management, new automotive catalysts and the use of renewable fuels which contributes to reduce the environmental impact. The purpose of this study was a comparative analysis of gas emissions from a automotive vehicle, operating with different fuels: natural gas, AEHC or gasoline. To execute the experimental tests, a flex vehicle was installed on a chassis dynamometer equipped with a gas analyzer and other complementary accessories according to the standard guidelines of emission and security procedures. Tests were performed according to NBR 6601 and NBR 7024, which define the urban and road driving cycle, respectively. Besides the analysis of exhaust gases in the discharge tube, before and after the catalyst, using the suction probe of the gas analyzer to simulate the vehicle in urban and road traffic, were performed tests of fuel characterization. Final results were conclusive in indicating leaded gasoline as the fuel which most contributed with pollutant emissions in atmosphere and the usual gasoline being the fuel which less contributed with pollutant emissions in atmosphere

Estudo do perfil térmico de fornos do tipo "caipira" utilizados pelo setor de cerâmica vermelha em parelhas na região Seridó-RN

The present study aimed to characterize the thermal profile of wood fired oven used by the red ceramic industry in Parelhas, in the Seridó region/RN, aiming to propose structural interventions that can contribute to increasing productivity and product quality, optimize wood consumption and mitigate existing losses during the burning process. The study was conducted at Cerâmica Esperança in the city of Parelhas -RN, Brazil, during the period from August 2012 to September 2013. Four treatments were performed with three replicates, ie, with, a total of 12 experimental units (burnings). In the first stage 4 treatments were performed with three replicates, totaling 12 experimental units (firings). In the second stage 2 treatments were performed with three replications, totaling 6 experimental units (firings). The physical characteristics of the wood were analyzed using standard NBR 11941 and NBR 7190 for basic density and moisture, respectively. The clay was used as a reference parameter for distinguishing treatments. For both the analysis and characterization was carried out using techniques of fluorescence X (XRF) rays, X-ray diffraction (XRD) analysis, particle size analysis (FA). In the first and second stages were monitored: the time during the firing process, the amount of wood used at each firing, the number of parts enfornadas for subsequent determination of the percentages of losses, but also product quality. To characterize the thermal profile of the oven, we measured the temperature at 15 points scored in the surface charge put into the oven. Measurements were taken every 30 minutes from preheat until the end of burning, using a pyrometer laser sight sighting from preheating until the end of burning. In the second step 12 metal cylinders distributed on the oven walls, and the cylinder end walls 8 of the furnace 2 and rollers on each side walls are installed equidistant to 17 cm from the soil and the surface 30 of the wall are installed. The cylinders distributed on the front were placed 50 cm above the furnace, and the base of the oven 20 cm distant from the ground. 10 also thermocouples were installed, and five thermocouples distributed 1.77 cm above the combustion chambers, and one thermocouple on each side, and three thermocouples in front of the oven. We carried out the measurements of the temperatures every 1 hour during the burning two hours in cooling the cylinders with a pyrometer and thermocouples for dattaloger. These were fixed with depth of 30 cm from the wall. After statistical analysis it was found that: the thermal profile of the furnace surface and at different heights was heterogeneous; and the ranges of density and moisture content of wood are within recommended for use as an energy source standards. We conclude that even at low temperatures reached during firing there was a significant production of good quality products, this is due to high concentrations of iron oxide and potassium oxide found in clay, which lowers the melting point of the piece. The average burn time for each step varied 650-2100 minutes wood consumption was on average 20 m3, product quality was on average 16% of first quality, 70% second, third and 5% to 10% loss . The distance between the wire and the surface of the oven was a significant parameter for all treatments, but with different variations, meaning that the wire should not be so generic and unique form, used as a criterion for completion of the burn process. The central part of the furnace was the area that reached higher temperature, and in a unified manner, with the highest concentration of top quality products. The ideal temperature curve, which provided the highest quality of ceramic products was achieved in the central part of the furnace

Regulação do livre acesso no transporte de gás natural à luz da ordem econômica da Constituição de 1988

In the middle of modern social changes produced by globalization and capitalism, several markets have changed. States have left the direct coordination of these markets (chiefly public utility sector in the form of monopolies), introducing regulation in order to promote competition. These changes have affected natural gas industry by promoting competition as a key factor to the development and the increase of firms in this market. The regulatory reform of natural gas industry ocurred in EUA and Europe Union and it has produced its first results. In Brazilian context, Constitutional Amendment nbr. 09 and Federal Law nbr. 9.478/97 ( Petroleum Law ) opened the natural gas market to a broad range of private economic agents and they finished the monopoly over the industry before managed by Petrobras. The new regulatory framework of Brazilian natural gas industry has designed competition as a central element to the new form of managment of business and contractual relationships of this industry. Among the regulatory instruments, open access regulation in natural gas pipelines is directed to promote competition. The questions arised about its implementation in Brazilian context are studied in the present work, in which it is discussed the constitutional rules and principles are to be applied to the open access regulation within the theme of statal regulation of economy present in constitutional economic order

Estudo ergonômico do posto de atividade discente em instituição de ensino superior

This research carried through an ergonomic study of the rank of learning activity of a IES, was applied a questionnaire with ergonomic pointers structuralized in scale to intervalar of semantic differential of 0 the 10, in 290 pupils with ages between 18 and 52 years distributed for 5 courses in 9 classrooms, the sample was of the simple random probabilist type. The used statistical techniques had been the descriptive analysis and the analysis of clusters through statistica software 5,0 considering p £ 0,0500. Involving the following 0 variable: Layout; Colors; Acoustics; Illumination; Temperature; Position; Didactic furniture, and Equipment. The gotten results point to consider that the layout of the rooms, the perception of acoustic comfort, the position of the pupils and the furniture of the searched classrooms had been the condicionantes that had been more distinguished negative how much to the perception of comfort of the user. The the 91,5 NPS varied of 57,9 dB(A) values above of recommended for classrooms in accordance with NBR 10152; NR 15; NR 17; It would carry nº 3214/1978, of the Ministry of the Work and searched literature. The Illumination registered interval of 139 the 966 Lux, values are of the limits of interval recommended for classrooms according to NBR 5413 and NR 17. The thermal temperature registered interval of 24° 25,9ºC; URA 41,6 79.1% and the 0.1 air speed 1,0 m/s, values above of recommended for classrooms according to NBR the 6401 and NR 17. The research still suggests that it would have associations between pains in the body the positions of the pupils and the furniture of the classrooms. The results suggest research especially add for the conditions thermal and acoustics of the classrooms

Análise comparativa entre propriedades mecânicas, termofísicas e geométricas de tijolos produzidos pelos fornos caieira e abóbada

In the State of Rio Grande do Norte potteries are distributed in several counties in the four meso, which are: West Potiguar, Center Potiguar, Agreste Potiguar and East Portiguar. The ceramics, mostly, are responsible for products used in construction as bricks, tiles and white brick and wood used as fuel. This paper had a primary focus in the region of Seridó. The furnaces in this region, used to manufacture bricks are configured Caieira and Valt, in most of them using principles rustic, usually operated in an empirical way, using principles of control rather primitive, predominantly visual control. The focus of this study was to analyze the differences in the thermophysical, mechanical and geometric characteristics of bricks produced by Caieira and vault furnaces, using the NBR 15720 and the evaluation of energy efficiency in both furnaces. Thermophysical characteristics were analyzed through tests to determine the water absorption obtained from the difference between dry mass and wet mass of the sample and analysis of the thermal gradient, the mechanical characteristics from determination of the compressive strength of ceramic brick popularly known as bricks and also analyzed the geometrical characteristics of the bricks in order to verify the homogeneity of manufacturing. The tests showed that the energy difference of the two furnaces is not considered responsible for a significant difference in the properties of the products

Prospects for the use of municipal tree pruning wastes in particleboard production

The purpose of this study was to evaluate the physical and mechanical properties of particleboard made with pruning wastes from Ipê (Tabebuia serratifolia) and Chapéu-de-Sol (Terminalia catappa) trees. Particleboards were prepared with both wood species, using all the material produced by grinding the pruning wastes. The particleboards had dimensions of 45×45 cm, a thickness of approximately 11.5 mm and an average density of 664 kg/m3. A urea-formaldehyde adhesive was used in the proportion of 12% of the dry particle mass. The particleboards were pressed at a temperature of 130 C for 10 mins. The physical and mechanical properties analyzed were density, moisture content, thickness swelling, percentage of lignin and cellulose, modulus of resilience, modulus of elasticity and tensile strength parallel to the grain, accordingly to the standards NBR 14810 and CS 236-66 (1968). The particleboards were considered to be of medium density. The particle size significantly affected the static bending strength and tensile strength parallel to the grain. Ipê presented better results, demonstrating a potential for the production and use of particleboard made from this species. © The Author(s) 2013.

Aproveitamento de madeiras tropicais para confecção e avaliação de painéis aglomerados com mistura de partículas e resinas alternativas

Pós-graduação em Engenharia Civil - FEIS

Análise experimental do comportamento de vigas mistas de concreto e alvenaria estrutural sujeitas à flexão simples

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aderência aço-concreto: uma análise do comportamento do concreto fabricado com resíduos de borracha

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Resistência ao cisalhamento de vigas “T” de concreto armado: verificação das longarinas da ponte sobre o rio Sororó

O comportamento estrutural de uma viga T permite avaliar diferentes contribuições de resistência ao cisalhamento entre partes distintas de uma mesma seção transversal, permitindo estabelecer diretrizes para a disposição de armadura nessas regiões. Para quantificar as participações de mesas colaborantes e almas desse tipo de seção na resistência característica ao cisalhamento, foram investigadas experimentalmente 10 vigas de concreto armado constituídas de seções T, visando avaliar as recomendações da norma NBR, ACI e EC2 no que se refere ao desempenho de vigas T ao cisalhamento. Uma das vigas foi confeccionada para testemunho e as demais foram idealizadas com variação nas dimensões da mesa, para aumentar assim a área de concreto colaborante da seção. A armadura de flexão foi mantida constante em todos os casos e a armadura de cisalhamento foi suprimida, para que todas as vigas tivessem rupturas por cisalhamento antecipadas em relação à ruína por flexão. O concreto utilizado teve resistência à compressão de 47 MPa. Percebe-se claramente a influência da mesa colaborante na resistência última ao cisalhamento dos elementos estruturais ensaiados. O aumento da carga última foi significativo nas vigas com abas, passando do dobro da carga da viga de referência, e mais ainda, nas vigas com altura (hf) de 80 mm, nas quais a contribuição da mesa foi capaz de modificar o modo de ruptura das peças cujas armaduras de flexão entraram em processo de escoamento e o incremento de rigidez dado aos elementos em virtude do aumento da área de concreto (abas) da seção transversal foi em torno de 25%. A partir destes e outros resultados foi possível amplificar a resistência ao cisalhamento das longarinas da ponte sobre o rio Sororó da ferrovia Carajás em 1,93 vezes a resistência teórica para viga retangular no caso.