Plataforma de simulación en Matlab-Simulink de un accionamiento regulado para emular aerogeneradores

En este proyecto se desarrolla un modelo de simulación de un accionamiento controlado que emula el comportamiento de una turbina eólica, el cual se ha llevado a cabo a través del programa para simulación Matlab/Simulink. Su desarrollo se ha estructurado de la siguiente forma: Tras una breve introducción a la energía eólica y a las máquinas eléctricas objeto de estudio en este proyecto, se procede a la caracterización y representación de dichas maquinas dentro de la plataforma de simulación virtual Simulink. Posteriormente se explican posibles estrategias de control de la máquina de inducción, las cuales son aplicadas para la realización de un control de velocidad. Asimismo, se realiza un control vectorial de par de la máquina de inducción de modo que permita un seguimiento efectivo del par de referencia demandado por el usuario, ante distintas condiciones. Finalmente, se añade el modelo de turbina eólica de manera que, definiendo los valores de velocidad de viento, ángulo de paso y velocidad del eje, permite evaluar el par mecánico desarrollado por la turbina. Este modelo se valida comprobando su funcionamiento para diferentes puntos de operación ante diversas condiciones del par de carga. Las condiciones de carga se establecen acoplando al modelo de la turbina, un generador síncrono de imanes permanentes conectado a una carga resistiva. ! II! ABSTRACT In this project, the simulation model of a controlled drive that emulates the behaviour of a wind turbine is developed. It has been carried out through the platform for multidomian simulation called Matlab/Simulink. Its development has been structured as follows: After a brief introduction to the wind energy and the electrical machines studied in this project, these machines are characterized and represented into the virtual simulation platform, Simulink. Subsequently, the possible control strategies for the induction machine are explained and applied in order to carry out a speed control. Additionally, a torque vector control of the induction machine is performed, so as to enable an effective monitoring of the reference torque requested by the user, under different conditions. Finally, the wind turbine model is implemented so as to assess the turbine mechanical torque, after defining the wind speed, the pitch angle and the shaft speed values. This model is validated by testing its functionality for different operating points under various load torques. The load conditions are set up by attaching a permanent magnets synchronous machine, with a resistive load, to the turbine model.

Scaling and non-scaling of muscle activity, kinematics, and dynamics in sit-ups with different degrees of difficulty

The purpose of this study was to investigate how the CNS adjusts motor patterns for variants of a complex axial movement-the situp. Adjustments were induced by changing the support surface contact and mass distribution of the body. Healthy adults performed straight-legged sit-ups, 3 s in duration, with support added to or removed from the lumbar trunk, or with mass added to the head or to the legs. Each of these interventions either increased or decreased the difficulty of the task. The study addressed the extent to which changes in sit-up difficulty are compensated by scaling of muscle activity, kinematics, and dynamics versus the extent to which they are compensated by changing discretely the motor pattern. The analysis of muscle activity, kinematics, and dynamics focused on the first 30-40% of the sit-up-the trunk flexion phase-since this is the most critical part of the movement. Our results demonstrate that, in some respects, sit-up kinematics and dynamics scaled with difficulty, but in other respects, they did not. Muscle activity also scaled, in many respects, but in more difficult sit-ups, abdominal flexor activity decreased instead of increased. Non-scaling changes in these parameters suggest that complex movements, such as the sit-up, may require discrete changes in motor pattern in order to deal with large loads, which challenge the available leverage. (C) 2005 Elsevier Ltd. All rights reserved.

Proposta de uma metodologia para obtenção de um gerador síncrono com rotor de ímãs permanentes inclinados axialmente para microcentrais elétrica a partir de motor de indução

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Contributo para a modelização de magnetos supercondutores de fluxo residual: aplicação a um motor linear todo supercondutor

Dissertação para obtenção do Grau de Mestre em Engenharia Electrotécnica e de Computadores

Contributo para o estudo do motor linear síncrono supercondutor

Dissertação para obtenção do Grau de Mestre em Engenharia Electrotécnica e de Computadores

Projeto de um alternador síncrono em disco para um gerador com energia das ondas

Dissertação para obtenção do Grau de Mestre em Engenharia Eletrotécnica e Computadores

FPGA field oriented control of an axial flux motor-in-wheel

This paper presents the design and the prototype implementation of a three-phase power inverter developed to drive a motor-in-wheel. The control system is implemented in a FPGA (Field Programmable Gate Array) device. The paper describes the Field Oriented Control (FOC) algorithm and the Space Vector Modulation (SVM) technique that were implemented. The control platform uses a Spartan-3E FPGA board, programmed with Verilog language. Simulation and experimental results are presented to validate the developed system operation under different load conditions. Finally are presented conclusions based on the experimental results.

Field oriented control of an axial flux permanent magnet synchronous motor for traction solutions

Electric Vehicles (EVs) are increasingly used nowadays, and different powertrain solutions can be adopted. This paper describes the control system of an axial flux Permanent Magnet Synchronous Motor (PMSM) for EVs powertrain. It is described the implemented Field Oriented Control (FOC) algorithm and the Space Vector Modulation (SVM) technique. Also, the mathematical model of the PMSM is presented. Both, simulation and experimental, results with different types of mechanical load are presented. The experimental results were obtained using a laboratory test bench. The obtained results are discussed.

Performance Characteristics of an Axial-Flux Solid-Rotor-Core Induction Motor

The integration of electric motors and industrial appliances such as pumps, fans, and compressors is rapidly increasing. For instance, the integration of an electric motor and a centrifugal pump provides cost savings and improved performance characteristics. Material cost savings are achieved when an electric motor is integrated into the shaft of a centrifugal pump, and the motor utilizes the bearings of the pump. This arrangement leads to a smaller configuration that occupies less floor space. The performance characteristics of a pump drive can be improved by using the variable-speed technology. This enables the full speed control of the drive and the absence of a mechanical gearbox and couplers. When using rotational speeds higher than those that can be directly achieved by the network frequency the structure of the rotor has to be mechanically durable. In this thesis the performance characteristics of an axial-flux solid-rotor-core induction motor are determined. The motor studied is a one-rotor-one-stator axial-flux induction motor, and thus, there is only one air-gap between the rotor and the stator. The motor was designed for higher rotational speeds, and therefore a good mechanical strength of the solid-rotor-core rotor is required to withstand the mechanical stresses. The construction of the rotor and the high rotational speeds together produce a feature, which is not typical of traditional induction motors: the dominating loss component of the motor is the rotor eddy current loss. In the case of a typical industrial induction motor instead the dominating loss component is the stator copper loss. In this thesis, several methods to decrease the rotor eddy current losses in the case of axial-flux induction motors are presented. A prototype motor with 45 kW output power at 6000 min-1 was designed and constructed for ascertaining the results obtained from the numerical FEM calculations. In general, this thesis concentrates on the methods for improving the electromagnetic properties of an axial-flux solid-rotor-core induction motor and examines the methods for decreasing the harmonic eddy currents of the rotor. The target is to improve the efficiency of the motor and to reach the efficiency standard of the present-day industrial induction motors equipped with laminated rotors.

Estudo de um motor linear tubular de relutância chaveado de fluxo transversal

Resumo não disponível.

Controle vetorial de velocidade de um motor de indução trifásico com estimação neural de fluxo

This work describes the study and the implementation of the speed control for a three-phase induction motor of 1,1 kW and 4 poles using the neural rotor flux estimation. The vector speed control operates together with the winding currents controller of the stator phasis. The neural flux estimation applied to the vector speed controls has the objective of compensating the parameter dependences of the conventional estimators in relation to the parameter machine s variations due to the temperature increases or due to the rotor magnetic saturation. The implemented control system allows a direct comparison between the respective responses of the speed controls to the machine oriented by the neural rotor flux estimator in relation to the conventional flux estimator. All the system control is executed by a program developed in the ANSI C language. The main DSP recources used by the system are, respectively, the Analog/Digital channels converters, the PWM outputs and the parallel and RS-232 serial interfaces, which are responsible, respectively, by the DSP programming and the data capture through the supervisory system

Controlador adaptativo por modelo de referência e estrutura variável aplicado ao controle de ângulo de carga e fluxo de campo de um gerador síncrono

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

The sit-up: complex kinematics and muscle activity in voluntary axial movement

This paper describes the kinematics and muscle activity associated with the standard sit-up, as a first step in the investigation of complex motor coordination. Eight normal human subjects lay on a force table and performed at least 15 sit-ups, with the arms across the chest and the legs straight and unconstrained. Several subjects also performed sit-ups with an additional weight added to the head. Support surface forces were recorded to calculate the location of the center of pressure and center of gravity; conventional motion analysis was used to measure segmental positions; and surface EMG was recorded from eight muscles. While the sit-up consists of two serial components, 'trunk curling' and 'footward pelvic rotation', it can be further subdivided into five phases, based on the kinematics. Phases I and II comprise trunk curling. Phase I consists of neck and upper trunk flexion, and phase II consists of lumbar trunk lifting. Phase II corresponds to the point of peak muscle contraction and maximum postural instability, the 'critical point' of the sit-up. Phases III-V comprise footward pelvic rotation. Phase III begins with pelvic rotation towards the feet. phase W with leg lowering, and phase V with contact between the legs and the support surface. The overall pattern of muscle activity was complex with times of EMG onset, peak activity, offset, and duration differing for different muscles. This complex pattern changed qualitatively from one phase to the next, suggesting that the roles of different muscles and, as a consequence, the overall form of coordination, change during the sit-up. (C) 2003 Elsevier Science Ltd. All rights reserved.

Emulação de um motor de combustão interna através de um acionamento eletromecânico de velocidade variável utilizando um motor de indução trifásico

Dissertação para obtenção do grau de Mestre em Engenharia Electrotécnica Ramo de Energia

Projecto e ensaio de um motor de indução em disco com armadura supercondutora

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores