Avaliação de circuito eletrônico para medição de temperatura em instalações agrícolas por meio da porta paralela de um computador

Os sistemas de aquisição de dados de temperatura disponíveis comercialmente apresentam alto custo e grande complexidade operacional para a sua utilização em instalações agrícolas climatizadas. Este trabalho teve por objetivos propor, calibrar e validar um circuito eletrônico de baixo custo para a aquisição de dados de temperatura com base na freqüência de oscilação da tensão elétrica (0 a 5 V). O sensor empregado no circuito foi um termistor com resistência ômica de 10 kômega 25 ºC e coeficiente de temperatura negativo. O circuito eletrônico, conectado a um computador via porta paralela, foi calibrado por comparação com um termômetro-padrão de mercúrio em vidro. Após as medições, análises de regressão foram realizadas com os dados experimentais, gerando-se equações que relacionam freqüência com resistência e resistência com temperatura. Os coeficientes de determinação demonstraram excelentes correlações entre as variáveis (R² > 0,9999). Posteriormente, foram realizadas comparações entre as medições obtidas com o circuito eletrônico e dois sistemas convencionais de aquisição de dados. Os resultados demonstraram que o circuito proposto é capaz de medir com exatidão e precisão a temperatura na faixa de 10 a 40 ºC.

Quadro equilibrado de indicadores de desempenho para a gestão estratégica empresarial : aplicação a uma pequena empresa da área de serviço público de energia elétrica

Este trabalho versa sobre a estruturação de um sistema de indicadores de desempenho empresarial. Através de estudo de caso junto a uma organização da área de serviços de energia elétrica, incorpora características peculiares por tratar-se de uma cooperativa. Após um trabalho de pesquisa junto às obras de diversos autores e verificado o estado da arte em relação ao tema, efetuou-se uma análise da empresa estudada quanto ao seu estágio atual de desenvolvimento, ao ambiente, à cultura e a sua situação no contexto mercadológico. Com base nos resultados dessa análise, concluiu-se que um BSC – Balanced Scorecard -, segundo um modelo proposto por Kaplan e Norton, seria o mais adequado entre os estudados. Um Quadro Equilibrado de Indicadores, evolutivo, alinhado com a estratégia e relações de causa e efeito, é o resultado principal desta dissertação. Contudo, a ordenação e o relacionamento dos elementos entre si, integrados na arquitetura do Quadro de Indicadores, redundaram num subproduto, qual seja, um caminho alternativo para estruturá-lo, visto que a forma hierárquica inicialmente proposta pelos autores conflitou com a estratégia e a missão/visão da empresa. No final, o trabalho apresenta a estrutura de um Quadro Equilibrado de Indicadores para a instituição estudada e algumas conclusões sobre o sistema de medição de desempenho.

Sistema de medição de energia baseado no medidor de energia Teridian 71M6515H

Esta tese de mestrado descreve o desenvolvimento, implementação e teste de um sistema de medição de energia concebido para um ambiente doméstico, baseado no circuito integrado medidor de energia Teridian 71M6515H. O sistema desenvolvido envia periodicamente os valores monitorizados para uma base de dados, através de uma rede sem fios com base no protocolo IEEE 802.11 (Wi-Fi). Os dados podem ser acedidos remotamente em tempo real, através de uma página na internet, onde é possível consultar a quantidade de energia consumida acumulada. Na primeira fase deste trabalho realizou-se o enquadramento do tema no contexto atual, realizando-se o estudo de alguns sistemas domésticos de monitorização do consumo de energia elétrica existentes no mercado. Numa segunda fase foi realizado o estudo dos componentes a serem utilizados, o desenho da placa de circuito impresso e o desenvolvimento do firmware, para que todo o processamento e manipulação dos dados fossem realizados pela unidade de aquisição de dados. Em seguida procedeu-se à construção da unidade de aquisição e à programação para o registo dos valores numa base de dados. A última fase consistiu nos testes de funcionamento da unidade de aquisição em conjunto com a aplicação de registo de dados. Com a implementação do sistema desenvolvido o consumidor doméstico poderá ter conhecimento, em tempo real, do custo de funcionamento dos equipamentos que possui e assim tomar decisões para os utilizar de forma mais racional, o que se pode traduzir numa economia dos recursos energéticos.

A pegada de carbono como um dos indicadores de sustentabilidade para medição da responsabilidade socioambiental empresarial: um estudo de caso na unidade sede da Petrobras em Natal-RN

As a contemporary tendency, it is been evidenced that the environmental changes theme, already admitted as a concernment to international economical and political reality, is also gaining repercussion on industrial and business sector. Firms are implementing actions on trial to minimize their own greenhouse gases (GHG) emissions impacts. However, the great majority of those actions of Corporative Social-Environmental Responsibility (CSR) are referred only to direct emissions of the main production systems. Direct emissions are those derived of an isolate process, without considering the upstream and downstream processes emissions, which respond for the majority of emissions originated because of respective firm‟s production system existence. Because the greenhouse effect occurs globally and the GHG emissions contribute to the environmental changes independently of their origin, it must be taken into account the whole productive life cycle of products and systems, since the energy invested on resources extraction and necessary materials to the final disposal. To do so, it must be investigated all relevant steps of a product/production system life cycle, tracking all activities which emit greenhouse gases, directly or indirectly. This amount of emissions consists in the firm‟s Carbon Footprint. This research purpose is to defend the Carbon Footprint relevance and its adoption viability to be used as an Environmental Indicator on measurement/assessment of CSR. It has been realized a study case on Petrobras‟s seat unity at Natal-Brazil, assessing part of its Carbon Footprint. It has been used the software GEMIS 4.6 to do the emissions quantifying. The items measured were the direct emissions of the own unity vehicles and indirect emissions of offset paper (A4), energy and disposable plastic cups consumed. To 2009, these emissions were 3.811,94 tCO2eq. We may conclude that Carbon Footprint quantification is indispensable to the knowledge of real emissions caused by a productive process existence, must serving as basis to CSR decisions about the environmental changes reversion challenge

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developing the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. It s important to point out that, in spite of the loads being normally connected to the transformer s secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Software inteligente embarcado aplicado à correção de erro na medição de vazão em gás natural

This study developed software rotines, in a system made basically from a processor board producer of signs and supervisory, wich main function was correcting the information measured by a turbine gas meter. This correction is based on the use of an intelligent algorithm formed by an artificial neural net. The rotines were implemented in the habitat of the supervisory as well as in the habitat of the DSP and have three main itens: processing, communication and supervision

Um algoritmo para estimação de estado em alimentadores de distribuição de energia elétrica com base no método da soma de potências

Most algorithms for state estimation based on the classical model are just adequate for use in transmission networks. Few algorithms were developed specifically for distribution systems, probably because of the little amount of data available in real time. Most overhead feeders possess just current and voltage measurements at the middle voltage bus-bar at the substation. In this way, classical algorithms are of difficult implementation, even considering off-line acquired data as pseudo-measurements. However, the necessity of automating the operation of distribution networks, mainly in regard to the selectivity of protection systems, as well to implement possibilities of load transfer maneuvers, is changing the network planning policy. In this way, some equipments incorporating telemetry and command modules have been installed in order to improve operational features, and so increasing the amount of measurement data available in real-time in the System Operation Center (SOC). This encourages the development of a state estimator model, involving real-time information and pseudo-measurements of loads, that are built from typical power factors and utilization factors (demand factors) of distribution transformers. This work reports about the development of a new state estimation method, specific for radial distribution systems. The main algorithm of the method is based on the power summation load flow. The estimation is carried out piecewise, section by section of the feeder, going from the substation to the terminal nodes. For each section, a measurement model is built, resulting in a nonlinear overdetermined equations set, whose solution is achieved by the Gaussian normal equation. The estimated variables of a section are used as pseudo-measurements for the next section. In general, a measurement set for a generic section consists of pseudo-measurements of power flows and nodal voltages obtained from the previous section or measurements in real-time, if they exist -, besides pseudomeasurements of injected powers for the power summations, whose functions are the load flow equations, assuming that the network can be represented by its single-phase equivalent. The great advantage of the algorithm is its simplicity and low computational effort. Moreover, the algorithm is very efficient, in regard to the accuracy of the estimated values. Besides the power summation state estimator, this work shows how other algorithms could be adapted to provide state estimation of middle voltage substations and networks, namely Schweppes method and an algorithm based on current proportionality, that is usually adopted for network planning tasks. Both estimators were implemented not only as alternatives for the proposed method, but also looking for getting results that give support for its validation. Once in most cases no power measurement is performed at beginning of the feeder and this is required for implementing the power summation estimations method, a new algorithm for estimating the network variables at the middle voltage bus-bar was also developed

Projeto e controle de um sistema de aquecimento no Laboratório de Avaliação de Medição em Petróleo

The Oil Measurement Evaluation Laboratory (LAMP), located in the Federal University of Rio Grande do Norte (UFRN), has as main goal to evaluate flow and BS&W meters, where the simulation of a bigger number of operation variable in field, guarantees a less uncertain evaluation. The objective of this work is to purpose a heating system design and implementation, which will control the temperature safely and efficiently in order to evaluate and measure it. Temperature is one of the variables which influence the flow and BS&W accurate measurement, directly affecting the fluid viscosity and density in the experiment. To project the heating system it is of great importance to take the laboratory requirements, conditions and current restrictions into consideration. Three alternatives were evaluated: heat exchanger, internal resistance and external resistance. After the analyses are made in order to choose the best alternative for the heating system in the laboratory, control strategies were determined for it, PID control methods in combination with fuzzy logic were used. Results showed a better performance with fuzzy logic than with classic PID

Sistemas de automação e supervisão do laboratório de avaliação dos processos de medição de vazão e BSW

During a petroleum well production process, It is common the slmultaneous oil and water production, in proportion that can vary from 0% up to values close to 100% of water. Moreover, the production flows can vary a lot, depending on the charaeteristies of eaeh reservoir. Thus being, the meters used in field for the flow and BSW (water in the oil) measurement must work well in wide bands of operation. For the evaluation of the operation of these meters, in the different operation conditions, a Laboratory will be built in UFRN, that has for objective to evaluate in an automatic way the processes of flow and BSW petroleum measurement, considering different operation conditions. The good acting of these meters is fundamental for the accuracy of the measures of the volumes of production liquid and rude of petroleum. For the measurement of this production, the petroleum companies use meters that should indicate the values with tha largast possible accuracy and to respect a series of conditions and minimum requirements, estabelished by the united Entrance ANP/INMETRO 19106/2000. The laboratory of Evafuation of the Processes of Measurement of Flow and BSW to be built will possess an oil tank basically, a tank of water, besides a mixer, a tank auditor, a tank for separation and a tank of residues for discard of fluids, fundamental for the evaluation of the flow metars and BSW. The whole process will be automated through the use of a Programmable Logicat Controller (CLP) and of a supervisory system.This laboratory besides allowing the evaluation of flow meters and BSW used by petroleum companies, it will make possible the development of researches related to the automation. Besides, it will be a collaborating element to the development of the Computer Engineering and Automation Department, that it will propitiate the evolution of the faculty and discente, qualifying them for a job market in continuous growth. The present work describes the project of automation of the laboratory that will be built at of UFRN. The system will be automated using a Programmable Logical Controller and a supervisory system. The programming of PLC and the screens of the supervisory system were developed in this work

Análise de Handover inter e intra-célula em um sistema de telefonia celular através de método de medição simplificado

This dissertation has the purpose to present a portable device named PlugData MG100G, equipped with a cellular module, to analyze the radiofrequency coverage in a GSM network situated in João Pessoa city, state of Paraíba, at four distinct regions. The equipment, originally, was developed to be used in fixed environments, so it was adapted so that it could be used in conditions of mobility. From the Mobile Measurement Reports (MMRs) RF coverage and the handover process are analyzed. The MMRs enable the identification of the serving cell and the list of the closest neighboring cells monitored by the mobile. This work analyses only data referent to the serving cell and the two closest neighboring cells. Inter-cell and intra-cell handovers are identified. The frequency planning and quality of service offered by the network related to the regions are discussed as well

Uma metodologia para redução de incertezas em sistema de medição de vazão de óleo e gás

The objective of this research is to discuss about the need for implementation of new alternatives for the implementation on the metrological control: on the findings of initial and subsequent measurements, the control procedures of measurement uncertainty applied in assessing the loss or remains found in handling operations of bulk liquids, when used turbine meters used in measuring the tax on the business of Petrobras, due to the current environment of legal metrology and scientific, both domestic and international. We aim, with these alternatives: standardizing the minimization of random and systematic errors, the estimate of the remaining errors, as well as the management control of metrological calibration procedures, control of measurement uncertainty, and contribute to the change in the form of performance of legal metrology and scientific disseminating new information to change management of metrological control, objectively focused on aspects of supervision in implementing these activities in the control of the uncertainties of measurement used in our processes in the fiscal measurement system Petrobras. Results are presented, information and comments on the influence of measurement uncertainty in the current results of the fiscal and transfer of custody. This will emphasize the need, among other things, improvement and expansion of metrological control monitored by setting a better meet demand, calibration equipment and measuring instruments for Petrobras. Finally, we intend to establish the need for improving the method of evaluation of the data meter applied to the current management control of measurement uncertainty by proposing a methodology for addressing the problem, as well as highlighting the expected results.

Estudo da estimativa da incerteza de medição para determinação do BS&W e da vazão aplicado no laboratório de avaliação de medição do petróleo

The considered work presents the procedure for evaluation of the uncertainty related to the calibration of flow measurers and to BS&W. It is about a new method of measurement purposed by the conceptual project of the laboratory LAMP, at Universidade Federal do Rio Grande do Norte, that intends to determine the conventional true value of the BS&W from the total height of the liquid column in the auditor tank, hydrostatic pressure exerted by the liquid column, local gravity, specific mass of the water and the specific mass of the oil, and, to determine the flow, from total height of liquid column and transfer time. The calibration uses a automatized system of monitoration and data acquisition of some necessary largnesses to determine of flow and BS&W, allowing a better trustworthiness of through measurements

Medição da densidade óssea através de ondas eletromagnéticas e classificação por MVS

This work holds the purpose of presenting an auxiliary way of bone density measurement through the attenuation of electromagnetic waves. In order to do so, an arrangement of two microstrip antennas with rectangular configuration has been used, operating in a frequency of 2,49 GHz, and fed by a microstrip line on a substrate of fiberglass with permissiveness of 4.4 and height of 0,9 cm. Simulations were done with silica, bone meal, silica and gypsum blocks samples to prove the variation on the attenuation level of different combinations. Because of their good reproduction of the human beings anomaly aspects, samples of bovine bone were used. They were subjected to weighing, measurement and microwave radiation. The samples had their masses altered after mischaracterization and the process was repeated. The obtained data were inserted in a neural network and its training was proceeded with the best results gathered by correct classification on 100% of the samples. It comes to the conclusion that through only one non-ionizing wave in the 2,49 GHz zone it is possible to evaluate the attenuation level in the bone tissue, and that with the appliance of neural network fed with obtained characteristics in the experiment it is possible to classify a sample as having low or high bone density

Sistema microcontrolado para medição de forças na região plantar e nos membros superiores de pacientes

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Modelação e análise da vida útil (metrológica) de medidores tipo indução de energia elétrica ativa

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)