Effects of variation in the palm stearin: palm olein ratio on the crystallisation of a low-trans shortening

Changes in the theological properties during crystallisation and in the crystal size and morphology of blends containing rapeseed oil with varying percentages of palm stearin (POs) and palm olein (POf) have been studied. The crystals formed from all three blends were studied by confocal laser scanning microscopy, light microscopy and environmental scanning electron microscopy, which revealed the development of clusters of 3-5 individual elementary "spherulites" in the early stages of crystallisation. The saturated triacylglycerol content of the solid crystals separated at the onset of crystallisation was much greater than that in the total fat. Fat blends with a higher content of palm stearin had a more rapid nucleation rate when observed by light microscopy, and this caused an earlier change in the rheological properties of the fat during crystallisation. Using a low torque amplitude (0.005 Pa, which was within the linear viscoelastic region of all samples studied) and a frequency of 1 Hz, the viscoelastic properties of melted fat during cooling were studied. All samples, prior to crystallisation, showed weak viscoelastic liquid behaviour (G '', loss modulus >G', storage modulus). After crystallisation a more "solid like" behaviour was observed (G' similar to or greater than G ''). The blend having the highest concentration of POs was found to have the earliest onset of crystallisation (27% w/w POs; 12 mins, 22% w/w POs; 13.5 mins, 17% w/w POs, 15 mins, respectively). However, there were no significant differences in the time to the point when G' became greater than G' among the three blends. (c) 2006 Elsevier Ltd. All rights reserved.

Effects of composition on fat rheology and crystallisation

The crystallisation behaviour of three fat blends, comprising a commercial shortening, a blend of fats with a very low trans fatty acid content ("low-trans") and a blend including hardened rapeseed oil with a relatively high trans fatty acid content ("high-trans") was studied. Molten fats were lowered to a temperature of 31 degrees C and stirred for 0, 15, 30, 45 and 60 min. Samples were removed and their rheological properties studied, using a controlled stress rheometer, employing a frequency sweep procedure. Effects of the progressive crystallisation at 31 degrees C on the melting profile of fat samples removed from the stirred vessel and solidified at -20 degrees C were also studied by differential scanning calorimetry (DSC). The rheological profiles obtained suggested that all of the fats studied had weak viscoelastic "liquid" structures when melted, but these changed to structures perceived by the rheometer as weak viscoelastic "gels" in the early stages of crystallisation (G' (storage modulus) > G" (loss modulus) over most of the measured frequency range). These subsequently developed into weak viscoelastic semi-solids, showing frequency dependent behaviour on further crystallisation. These changes in behaviour were interpreted as changes from a small number of larger crystals "cross-linking" in a liquid matrix to a larger number of smaller crystals packed with a "slip plane" of liquid oil between them. The rate of crystallisation of the three fats was in the order high trans > low-trans > commercial shortening. Changes in the DSC melting profile due to fractionation of triacylglycerols during the crystallisation at 31 degrees C were evident for all three fats. (c) 2006 Elsevier Ltd. All rights reserved.

Squeeze flow viscoelasticity of electrorheological fluids based on microcrystalline cellulose

Dynamic viscoelasticity of electrorheological fluids based on microcrystalline cellulose/castor oil suspensions was experimentally investigated in squeeze flow. The dependence of storage modulus G' and loss modulus G" parallel to external electric field on electric fields and strain amplitudes is presented. The experiments show that, when external electric field is higher than the critical field, the viscoelasticity of the ER fluids converts from linear to nonlinear, and the ER fluids transfer from solid-like state to fluid state with the growth of strain amplitude. The influences of strain amplitude and oscillatory frequency on the nonlinearity of viscoelasticity were also studied.

Effect of cold storage on culture viability and some rheological properties of fermented milk prepared with yogurt and probiotic bacteria

We examined the effect of storage time on culture viability and some rheological properties (yield stress, storage modulus, loss modulus, linear viscoelastic region, structural recuperation and firmness) of fermented milk made with Lactobacillus delbrueckii ssp. bulgaricus, Lactobacillus acidophilus (LA) and Bifidobacterium animalis ssp. lactis in coculture with Streptococcus thermophilus (ST). Acidification profiles and factors that affect viability (postfermentation acidification, acidity and dissolved oxygen) were also studied during 35 days at 4C. Fermented milk prepared with a coculture of ST and Bifidobacterium lactis gave the most constant rheological behavior and the best cell viability during cold storage; it was superior to ST plus LA for probiotic fermented milk production.

Semisolid systems containing propolis for the treatment of periodontal disease: In vitro release kinetics, syringeability, rheological, textural, and mucoadhesive properties

Formulations containing poloxamer 407 (P407), carbopol 934P (C934P), and propolis extract (PE) were designed for the treatment of periodontal disease. Gelation temperature, in vitro drug release, rheology, hardness, compressibility, adhesiveness, mucoadhesion, and syringeability of formulations were determined. Propolis release from formulations was controlled by the phenomenon of relaxation of polymer chains. Formulations exhibited pseudoplastic flow and low degrees of thixotropy or rheopexy. In most samples, increasing the concentration of C934P content significantly increased storage modulus (G'), loss modulus (G ''), and dynamic viscosity (n') at 5 degrees C, G '' exceeded G'. At 25 and 37 degrees C, n' of each formulation depended on the oscillatory frequency. Formulations showed thermoresponsive behavior, existing as a liquid at room temperature and gel at 34-37 degrees C. Increasing the C934P content or temperature significantly increased formulation hardness, compressibility, and adhesiveness. The greatest mucoadhesion was noted in the formulation containing 15% P407 (w/w) and 0.25% C934P (w/w). The work of syringeability values of all formulations were similar and very desirable with regard to ease of administration. The data obtained in these formulations indicate a potentially useful role in the treatment of periodontitis and suggest they are worthy of clinical evaluation. (c) 2007 Wiley-Liss, Inc.

Hygrothermal effects on damping behavior of metal/glass fiber/epoxy hybrid composites

Continuous fiber/metal laminates (FML) offer significant improvements over current available materials for aircraft structures due to their excellent fatigue endurance and low density. Glass fibers/epoxy laminae and aluminum foil (Glare) are commonly used to obtain these hybrid composites. The environmental factors can limit the applications of composites by deteriorating the mechanical properties during service. Usually, epoxy resins absorb moisture when exposed to humid environments and metals are prone to surface corrosion. Therefore, the combination of the two materials in Glare (polymeric composite and metal). can lead to differences that often turn out to be beneficial in terms of mechanical properties and resistance to environmental influences. In this work. The viscoelastic properties. such as storage modulus (E') and loss modulus (E'), were obtained for glass fiber/epoxy composite, aluminum 2024-T3 alloy and for a glass fiber/epoxy/aluminum laminate (Glare). It was found that the glass fiber/epoxy (G/E) composites decrease the E' modulus during hygrothermal conditioning up to saturation point (6 weeks). However, for Glare laminates the E' modulus remains unchanged (49GPa) during the cycle of hygrothermal conditioning. The outer aluminum sheets in the Glare laminate shield the G/E composite laminae from moisture absorption. which in turn prevent, in a certain extent, the material from hygrothermal degradation effects. (c) 2005 Elsevier B.V. All rights reserved.

Injectable gels of anionic collagen : rhamsan composites for plastic correction: Preparation, characterization, and rheological properties

The present article describes the preparation and characterization A anionic Collagen gels obtained from porcine intestinal submucosa after 72 h of alkaline treatment and in the form of rhamsan composites to develop injectable biomaterials for plastic for construction. All materials were characterized by SDS/polyacrylamide gel electrophoresis, infrared spectroscopy, thermal stability, potentiometric titration, rheological properties, and fluidity tests. Biocompatibility was appraised after the injection of anionic collagen:rhamsan composites at 2.5% in 60 North Folk rabbits. Independently of processing, the Collagen's secondary structure was preserved in all cases, and after 72 h of hydrolysis the Collagen was characterized by a carboxyl group content of 346 :L 9, which, at physiological pH, corresponds to an increase of 106 17 negative charges, in comparison to native Collagen, due to the selective hydrolysis of asparagine and glutamine carboxyamide side chain. Rheological studies of composites at pH 7.4 in concentrations of 2, 4, and 6% (in proportions of 75:1 and 50:1) showed a viscoelastic behavior dependent on the frequency, which is independent of concentration and proportion. In both, the concentration of the storage modulus always predominated over the loss modulus (G' > G and delta < 45 degrees). The results from creep experiments confirmed this behavior and showed that anionic collagen:rhamsan composites at pH 7.4 in the proportion of 50:1 are less elastic and more susceptible to deformation in comparison to gels in the proportion of 75:1, independent of concentration. This was further confirmed by flow experiments, indicating that the necessary force for the extrusion of anionic collagen:rhamsan composites, in comparison to anionic Collagen, was significantly smaller and with a smooth flow. Biocompatibility studies showed that the tissue reaction of anionic collagen:rhamsan composites at 2.5% in the proportion of 75:1 was compatible with the application of these gels in plastic reconstruction. These results suggest that the association of Collagen with rhamsan may be a good alternative in the replacement of glutaraidehyde to stabilize the microfibril assembly of commercial Collagen gel preparations. (c) 2005 Wiley Periodicals, Inc.

Effect of Biomimetic Remineralization on the Dynamic Nanomechanical Properties of Dentin Hybrid Layers

The mineral and organic phases of mineralized dentin contribute co-operatively to its strength and toughness. This study tested the null hypothesis that there is no difference in nano-dynamic mechanical behavior (complex modulus-E*; loss modulus-E ''; storage modulus-E'; in GPa) of dentin hybrid layers (baseline: E*, 3.86 +/- 0.24; E '', 0.23 +/- 0.05; E', 3.85 +/- 0.24) created by an etch-and-rinse adhesive in the presence or absence of biomimetic remineralization after in vitro aging. Using scanning probe microscopy and nano-dynamic mechanical analysis, we demonstrated that biomimetic remineralization restored the nano-dynamic mechanical behavior of heavily remineralized, resin-sparse regions of dentin hybrid layers (E*, 19.73 +/- 3.85; E '', 8.75 +/- 3.97; E', 16.02 +/- 2.58) to those of the mineralized dentin base (E*, 19.20 +/- 2.42; E '', 6.57 +/- 1.96; E', 17.39 +/- 2.0) [p > 0.05]. Conversely, those resin-sparse, water-rich regions degraded in the absence of biomimetic remineralization, with significant decline [p < 0.05] in their complex and storage moduli (E*, 0.83 +/- 0.35; E '', 0.88 +/- 0.24; E', 0.62 +/- 0.32). Intrafibrillar apatite deposition preserves the integrity of resin-sparse regions of hybrid layers by restoring their nanomechanical properties to those exhibited by mineralized dentin.

Damping behavior of hygrothermally conditioned carbon fiber/epoxy laminates

Carbon fiber reinforced polymer composites have been used in wide variety of applications including, aerospace, marine, sporting equipment as well as in the defense sector due to their outstanding properties at low density. In many of their applications, moisture absorption takes place which may result in a reduction in mechanical properties even at lower temperature service. In this work, the viscoelastic properties, such as storage modulus (E′) and loss modulus (E″), were obtained through vibration damping tests for three carbon fiber/epoxy composite families up to the saturation point (6 weeks). Three carbon fiber/epoxy composites having [0/0] s, [0/90] s, and [±45] s orientations were studied. During vibration tests the storage modulus (E′) and loss modulus (E″) were monitored as a function of moisture uptake, and it was observed that the natural frequencies and E′ values decreased with the increase during hygrothermal conditioning due to the matrix plasticization. © 2007 Wiley Periodicals, Inc.

Desenvolvimento e caracterização de sistemas micro e nanoestruturados para a administração cutânea de acetato de dexametasona

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Comportamento reológico de géis de amido de mandioquinha salsa (Arracacia xanthorrhiza B.)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Surfactant-cosurfactant interactions and process parameters involved in the formulation of stable and small droplet-sized benznidazole-loaded soybean O/W emulsions

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Tannin-phenolic resins: Synthesis, characterization, and application as matrix in biobased composites reinforced with sisal fibers

A tannin-phenolic resin (40 wt% of tannin, characterized by H-1 nuclear magnetic resonance (NMR) and C-13 NMR, Fourier transform infrared, thermogravimetry, differential scanning calorimetry) was used to prepare composites reinforced with sisal fibers (30-70 wt%). Inverse gas chromatography results showed that the sisal fibers and the tannin-phenolic thermoset have close values of the dispersive component and also have predominance of acid sites (acid character) at the surface, confirming the favoring of interaction between the sisal fibers and the tannin-phenolic matrix at the interface. The Izod impact strength increased up to 50 wt% of sisal fibers. This composite also showed high storage modulus, and the lower loss modulus, confirming its good fiber/matrix interface, also observed by SEM images. A composite with good properties was prepared from high content of raw material obtained from renewable sources (40 wt% of tannin substituted the phenol in the preparation of the matrix and 50 wt% of matrix was replaced by sisal fibers). (C) 2012 Elsevier Ltd. All rights reserved.

Synthese von flüssigkristallinen Polysiloxanen und Charakterisierung der smektischen Phasen

Gegenstand dieser Arbeit ist die Untersuchung der smektischen Phasen von Polysiloxanen mit flüssigkristallinen Seitengruppen (LC-Polysiloxane). Der erste Teil der vorliegenden Arbeit befasste sich mit der Herstellung verschiedener flüssigkristalliner ferroelektrischer Polysiloxane. Die Polymere wurden in Bezug auf das verwendete Polymerrückgrat (Homo- und Copolysiloxan) sowie durch den zusätzlichen Einbau von vernetzbaren Seitengruppen variiert. Im zweiten Teil der Arbeit wurden die Eigenschaften der smektischen Phasen der hergestellten Substanzen näher untersucht. Ein erster Untersuchungsgegenstand war das Dehnungsverhalten von freistehenden flüssigkristallinen Elastomerfilmen (LCE). Bei der Verwendung eines Polymers, in dem nur ein Teil des Polysiloxanrückgrats mit Seitengruppen substituiert ist, wird die uniaxiale Dehnung des Films parallel zu den smektischen Schichten durch eine gleichmäßige Kontraktion in der Filmebene und parallel zur Schichtnormalen ausgeglichen, was auf einen außergewöhnlich niedrigen smektischen Schichtkompressionsmodul zurückzuführen ist. Im Gegensatz dazu ist dieser Modul bei den Homopolymersystemen so groß, dass praktisch senkrecht zu den smektischen Schichten keine Kontraktion stattfindet. Ein zweiter Untersuchungsgegenstand der Netzwerkbildung bestand in der Bestimmung der dynamisch-mechanischen Eigenschaften der LC-Polysiloxane mittels eines Oszillationsrheometers. Hier erfolgten die Messungen von Speicher- und Verlustmodul in Abhängigkeit vom Polymerrückgrat und von der Vernetzung. Die unvernetzten Systeme zeigten in den smektischen Phasen (oberhalb Tg) noch – im wesentlichen – Festkörpereigenschaften (physikalische Vernetzung) mit einem dominierenden Speichermodul beim LC-Homopolysiloxan. Beim LC-Copolysiloxan haben beide Module eine gleiche Größenordnung. Am Phasenübergang in die isotrope Phase wurden beide Module absolut kleiner, der Verlustmodul aber relativ größer. In der isotropen Phase verhalten sich die LC-Polymere damit überwiegend wie viskose Schmelzen. Außerdem korrelierten die mittels DSC bestimmten Phasenübergangstemperaturen mit einer Änderung der dynamisch-mechanischen Eigenschaften. Nach der Vernetzung dominierte der Speichermodul sowohl beim LC-Homo- als auch beim LC-Copolysiloxan bis in die isotrope Phase, und es war aufgrund der Bildung einer festen Netzwerkstruktur keine Abhängigkeit der Module von Phasenübergängen mehr erkennbar. Als dritter Untersuchungsgegenstand wurde der Phasenübergang zwischen den beiden smektischen Phasen (SmC* nach SmA*) der flüssigkristallinen Polysiloxane näher behandelt. Als wichtigstes Ergebnis ist festzuhalten, dass die verdünnten LC-Polysiloxane an diesem Übergang fast keine Schichtdickenänderung aufweisen. Dazu wurde jeweils die röntgenographisch ermittelte Schichtdicke mit der aus den optischen Tiltwinkeln theoretisch berechneten Schichtdicke verglichen. Dadurch konnte gezeigt werden, dass sich die Phasenübergänge nach dem de Vries-Modell verhalten. Damit konnte zum ersten Mal an Polymersystemen ein de Vries-Verhalten nachgewiesen werden. Im Gegensatz dazu zeigte das Homopolysiloxan mit dem Dreiringmesogen beim Übergang von SmC* nach SmA* einen ausgeprägten Sprung in der Schichtdicke. Wie auch durch DSC-Messungen nachweisbar, lag ein Phasenübergang 1. Ordnung vor. Bei den LC-Copolysiloxanen liegt dagegen ein Phasenübergang 2. Ordnung vor. Schließlich wurde die Schichtdicke unter dem Einfluss der Vernetzung untersucht. Beim LC-Copolysiloxan mit dem Dreiringmesogen und einem Anteil an vernetzbaren Gruppen von 15 % wurde eine Stabilisierung der smektischen Phasen erreicht. Zum einen war die Änderung der Schichtdicke am SmC*-SmA*-Phasenübergang geringer im Vergleich zum unvernetzten System und zum anderen war noch 50 °C über der ursprünglichen Klärtemperatur eine smektische Schichtstruktur röntgenographisch nachzuweisen. Insgesamt ist es mit den verschiedenen Untersuchungsmethoden gelungen, einen systematischen Unterschied zwischen smektischen Homo- und Copolysiloxanen aufzuzeigen, der seinen Ursprung – aller Wahrscheinlichkeit nach – in der Mikrophasenseparation von Mesogenen und Polysiloxanketten findet.

Rheological and tribological properties of poly(phenylene sulphide) and poly(ether ether ketone) composites incorporating carbon nanotubes and inorganic nanoparticles: a comparative study

The rheological and tribological properties of single-walled carbon nanotube (SWCNT)-reinforced poly(phenylene sulphide) (PPS) and poly(ether ether ketone) (PEEK) nanocomposites prepared via melt-extrusion were investigated. The effectiveness of employing a dual-nanofiller strategy combining polyetherimide (PEI)-wrapped SWCNTs with inorganic fullerene-like tungsten disulfide (IF-WS2) nanoparticles for property enhancement of the resulting hybrid composites was evaluated. Viscoelastic measurements revealed that the complex viscosity ?, storage modulus G?, and loss modulus G? increased with SWCNT content. In the low-frequency region, G? and G? became almost independent of frequency at higher SWCNT loadings, suggesting a transition from liquid-like to solid-like behavior. The incorporation of increasing IF-WS2 contents led to a progressive drop in ? and G? due to a lubricant effect. PEEK nanocomposites showed lower percolation threshold than those based on PPS, ascribed to an improved SWCNT dispersion due to the higher affinity between PEI and PEEK. The SWCNTs significantly lowered the wear rate but only slightly reduced the coefficient of friction. Composites with both nanofillers exhibited improved wear behavior, attributed to the outstanding tribological properties of these nanoparticles and a synergistic reinforcement effect. The combination of SWCNTs with IF-WS2 is a promising route for improving the tribological and rheological performance of thermoplastic nanocomposites.