Improving mW/MHz ratio in FPGAs pipelined designs

This paper presents a simple clocking technique to migrate classical synchronous pipelined designs to a synchronous functional-equivalent alternative system in the context of FPGAs. When the new pipelined design runs at the same throughput of the original design, around 30% better mW/MHz ratio was observed in Virtex-based FPGA circuits. The evaluation is done using a simple but representative and practical systolic design as an example. The technique in essence is a simple replacement of the clocking mechanism for the pipe-storage elements; however no extra design effort is needed. The results show that the proposed technique allows immediate power and area-time savings of existing designs rather than exploring potential benefits by a new logic design to the problem using the classic pipeline clocking mechanism.

A low-voltage low-sensitivity sinusoidal VCO for DPLL realizations

A quasi-sinusoidal linearly tunable OTA-C VCO built with triode-region transconductors is presented. Oscillation upon power-on is ensured by RHP poles associated with gate-drain capacitances of OTA input devices. Since the OTA nonlinearity stabilizes the amplitude, the oscillation frequency f0 is first-order independent of VDD, making the VCO adequate to mixed-mode designs. A range of simulations attests the theoretical analysis. As part of a DPLL, the VCO was prototyped on a 0.8μm CMOS process, occupying an area of 0.15mm2. Nominal f0 is 1MHz, with K VCo=8.4KHz/mV. Measured sensitivity to VDD is below 2.17, while phase noise is -86dBc at 100-KHz offset. The feasibility of the VCO for higher frequencies is verified by a redesign based on a 0.35μm CMOS process and VDD=3.3V, with a linear frequency-span of l3.2MHz - 61.5MHz.

Discrete wavelet transform signal analyzer

This paper addresses the problem of processing biological data, such as cardiac beats in the audio and ultrasonic range, and on calculating wavelet coefficients in real time, with the processor clock running at a frequency of present application-specified integrated circuits and field programmable gate array. The parallel filter architecture for discrete wavelet transform (DWT) has been improved, calculating the wavelet coefficients in real time with hardware reduced up to 60%. The new architecture, which also processes inverse DWT, is implemented with the Radix-2 or the Booth-Wallace constant multipliers. One integrated circuit signal analyzer in the ultrasonic range, including series memory register banks, is presented. © 2007 IEEE.

Automatic cell generation for recurrence structures /

"NSF-OCA-MCS76-81686-000052."--Cover.

Program manual for the programs ILLOD-MINSUM-CBS, ILLOD-MINSUM-CBSA, ILLOD-MINSUM-CBG, and ILLOD-MINSUM-CBGM, to derive minimal sums or irredundant disjunctive forms for switching functions /

"UILU-ENG 78 1719."

NOR network transduction system : principles of the NETTRA system /

Bibliography: p. 209-212.

Program manual for the NETTRA system /

"UILU-ENG 77 1743."

Program manual of programs for minimal covering problems : ILLOD-MINIC-B, ILLOD-MINIC-BP, ILLOD-MINIC-BS, ILLOD-MINIC-BA, ILLOD-MINIC-BG /

Includes bibliography references.

Level-restricted NOR network transduction procedures /

"UILU-ENG 77 1703."

The role of the MCDU in the parallel element processing ensemble (PEPE) /

Thesis (M. S.)--University of Illinois at Urbana-Champaign.

A Design for Testability of Undetectable Crosspoint Faults in Programmable Logic Arrays

In this paper, the validity of'single fault assumption in deriving diagnostic test sets is examined with respect to crosspoint faults in programmable logic arrays (PLA's). The control input procedure developed here can be used to convert PLA's having undetectable crosspoint faults to crosspoint-irredundant PLA's for testing purposes. All crosspoints will be testable in crosspoint-irredundant PLA's. The control inputs are used as extra variables during testing. They are maintained at logic I during normal operation. A useful heuristic for obtaining a near-minimal number of control inputs is suggested. Expressions for calculating bounds on the number of control inputs have also been obtained.

Adaptive Keeper Design for Dynamic Logic Circuits Using Rate Sensing Technique

The increasing variability in device leakage has made the design of keepers for wide OR structures a challenging task. The conventional feedback keepers (CONV) can no longer improve the performance of wide dynamic gates for the future technologies. In this paper, we propose an adaptive keeper technique called rate sensing keeper (RSK) that enables faster switching and tracks the variation across different process corners. It can switch upto 1.9x faster (for 20 legs) than CONV and can scale upto 32 legs as against 20 legs for CONV in a 130-nm 1.2-V process. The delay tracking is within 8% across the different process corners. We demonstrate the circuit operation of RSK using a 32 x 8 register file implemented in an industrial 130-nm 1.2-V CMOS process. The performance of individual dynamic logic gates are also evaluated on chip for various keeper techniques. We show that the RSK technique gives superior performance compared to the other alternatives such as Conditional Keeper (CKP) and current mirror-based keeper (LCR).

A low power, process invariant keeper design for high speed dynamic logic circuits

A low power keeper circuit using the concept of rate sensing has been proposed. The proposed technique reduces the amount of short circuit power dissipation in the domino gate by 70% compared to the conventional keeper technique. Also the total power-delay product is 26% lower compared to the previously reported techniques. The process tracking capability of the design enables the domino gate to achieve uniform delay across different process corners. This reduces the amount of short circuit power dissipation that occurs in the cascaded domino gates by 90%. The use of the proposed technique in the read path of a register file reduces the energy requirement by 26% as compared to the other keeper techniques. The proposed technique has been prototyped in 130nm CMOS technology.