TCA Evaluation : Lab Measurements, Modelling and System Simulations

The study reported here is part of a large project for evaluation of the Thermo-Chemical Accumulator (TCA), a technology under development by the Swedish company ClimateWell AB. The studies concentrate on the use of the technology for comfort cooling. This report concentrates on measurements in the laboratory, modelling and system simulation. The TCA is a three-phase absorption heat pump that stores energy in the form of crystallised salt, in this case Lithium Chloride (LiCl) with water being the other substance. The process requires vacuum conditions as with standard absorption chillers using LiBr/water. Measurements were carried out in the laboratories at the Solar Energy Research Center SERC, at Högskolan Dalarna as well as at ClimateWell AB. The measurements at SERC were performed on a prototype version 7:1 and showed that this prototype had several problems resulting in poor and unreliable performance. The main results were that: there was significant corrosion leading to non-condensable gases that in turn caused very poor performance; unwanted crystallisation caused blockages as well as inconsistent behaviour; poor wetting of the heat exchangers resulted in relatively high temperature drops there. A measured thermal COP for cooling of 0.46 was found, which is significantly lower than the theoretical value. These findings resulted in a thorough redesign for the new prototype, called ClimateWell 10 (CW10), which was tested briefly by the authors at ClimateWell. The data collected here was not large, but enough to show that the machine worked consistently with no noticeable vacuum problems. It was also sufficient for identifying the main parameters in a simulation model developed for the TRNSYS simulation environment, but not enough to verify the model properly. This model was shown to be able to simulate the dynamic as well as static performance of the CW10, and was then used in a series of system simulations. A single system model was developed as the basis of the system simulations, consisting of a CW10 machine, 30 m2 flat plate solar collectors with backup boiler and an office with a design cooling load in Stockholm of 50 W/m2, resulting in a 7.5 kW design load for the 150 m2 floor area. Two base cases were defined based on this: one for Stockholm using a dry cooler with design cooling rate of 30 kW; one for Madrid with a cooling tower with design cooling rate of 34 kW. A number of parametric studies were performed based on these two base cases. These showed that the temperature lift is a limiting factor for cooling for higher ambient temperatures and for charging with fixed temperature source such as district heating. The simulated evacuated tube collector performs only marginally better than a good flat plate collector if considering the gross area, the margin being greater for larger solar fractions. For 30 m2 collector a solar faction of 49% and 67% were achieved for the Stockholm and Madrid base cases respectively. The average annual efficiency of the collector in Stockholm (12%) was much lower than that in Madrid (19%). The thermal COP was simulated to be approximately 0.70, but has not been possible to verify with measured data. The annual electrical COP was shown to be very dependent on the cooling load as a large proportion of electrical use is for components that are permanently on. For the cooling loads studied, the annual electrical COP ranged from 2.2 for a 2000 kWh cooling load to 18.0 for a 21000 kWh cooling load. There is however a potential to reduce the electricity consumption in the machine, which would improve these figures significantly. It was shown that a cooling tower is necessary for the Madrid climate, whereas a dry cooler is sufficient for Stockholm although a cooling tower does improve performance. The simulation study was very shallow and has shown a number of areas that are important to study in more depth. One such area is advanced control strategy, which is necessary to mitigate the weakness of the technology (low temperature lift for cooling) and to optimally use its strength (storage).

Partial purification and characterization of pectin methylesterase from orange (Citrus sinensis) cv. Pera-rio

The enzyme pectin methylesterase (PME) from orange was extracted and partially purified by filtration on Sephadex G-100. The extraction buffer for orange PME was borate-acetate containing 0.4 M NaCl. Orange PME showed optimum pH at 8.0 and optimum temperature at 50C. The PME enzyme was completely inactivated after 1 min of incubation at 90C. The specific activity increased in the presence of 0.15 M NaCl or 0.025 M Na2SO4, 0.10 M KCl, 0.025 M K2SO4, 0.05 and 0.1 M NH4Cl. Lithium chloride and Li(2)SO(4)inhibited the enzymatic activity at all concentrations studied. The K-m and V(max)value of PME were 0.36 mg/mL and 5.26 mu mol/mL-mg protein, respectively.

Determination of Sudan II dye in ethanol fuel by chromatographic and electroanalytical methods

Chromatographic and electroanalytical methods were developed to detect and quantify Sudan II (SD-II) dye in fuel ethanol samples. Sudan II is reduced at +0.50 V vs. Ag/AgCl on a glassy carbon electrode using Britton-Robinson buffer (pH 4.0) and N,N-dimethylformamide (70:30, v/v) + sodium dioctyl sulfosuccinate surfactant as supporting electrolyte, due to the azo group. This is the basis for its determination by square-wave voltammetry (SWV). Using the optimized conditions, it is possible to get a linear calibration curve from 3.00×10-6 to 1.80×10-5 mol L-1 (r = 0.998) with limits of detection (LOD) and quantification (LOQ) of 2.05×10-6 and 6.76×10-6 mol L-1, respectively. In addition, the hydroxyl substituent in the SD-II dye is also oxidized at +0.85 V vs. Ag/AgCl, which was conveniently used for its determination by high-performance liquid chromatography coupled to electrochemical detection (HPLC-ED). Under the optimized condition, the SD-II dye was eluted and separated using a reversed-phase column (cyanopropyl, CN) using isocratic elution with the mobile phase containing acetonitrile and aqueous lithium chloride (5.00×10-4 mol L-1) at 70:30 (v/v) and a flow rate of 1.2 mL min-1. Linear calibration curves were obtained from 3.00×10-7 to 2.00×10-6 mol L-1 (r = 0.999) with LOD and LOQ of 3.10×10-8 and 1.05×10-7 mol L-1, respectively. Both methods were simple, fast and suitable to detect and quantify the dye in fuel ethanol samples at recovery values between 83.0 to 102% (SWV) and 88.0 to 112% (HPLC-ED) with satisfactory precision and accuracy.

Conditioned food aversion to Ipomoea carnea var. fistulosa induced by Baccharis coridifolia in goats

Baccharis coridifolia é uma planta tóxica que possui forte poder aversivo em ruminantes. Os objetivos deste trabalho foram induzir aversão condicionada a Ipomoea carnea avar. fistulos em caprinos utilizando B. coridifolia como agente aversivo e comparar a eficiência desta aversão com a aversão induzida por cloreto de lítio (LiCl). Treze cabras foram divididas em dois grupos: o Grupo 1 com seis cabras foi avertido com 175mg/kg de peso corporal (pc) de LiCl e o Grupo 2, com sete cabras, foi avertido com 0,25g/kg de pc de B. coridifolia seco. Todas as cabras foram avertidas no dia 1 logo após a ingestão de I.carnea. A aversão foi repetida nos dias 2, 3 e 7 nos caprinos que ingeriram qualquer quantidade de I. carnea, utilizando-se o mesmo procedimento do dia 1. Os caprinos de ambos os grupos foram desafiados nas baias nos dias 23 e 38 após o último dia da aversão e desafiados na pastagem nos dias 11, 15, 18, 20, 22, 25, 27 e 29 após o último dia da aversão. Posteriormente os caprinos foram desafiados a cada 15 dias na pastagem até o 330º dia após o último dia da aversão (7º dia). Duas cabras do Grupo 1 ingeriram I. carnea no primeiro dia do desafio na pastagem, quatro dias após o ultimo dia da aversão nas baias. Além disso, outra cabra do mesmo grupo reiniciou a ingestão da planta no 18º dia e outras duas no 20º dia. Uma cabra do Grupo 1 que nunca havia ingerido a planta após a aversão morreu no 55º dia. Uma cabra do Grupo 2 começou a ingerir I. carnea no primeiro dia de desafio na pastagem e uma segunda reiniciou o consumo da planta no 182º dia. No final do experimento no 330º as cinco cabras avertidas com B. coridifolia permaneciam sem ingerir a planta. Estes resultados sugerem que B. coridifolia ou algum princípio ativo dessa planta pode ser utilizado para induzir aversão condicionada a plantas tóxicas. A utilização de B. coridifolia como agente aversivo é aparentemente mais barato e mais fácil de ser utilizado do que o LiCl, o qual requer o uso de sonda oro-gástrica e pessoal qualificado para sua implementação.

Myocardial Remodeling after Large Infarcts in Rat Converts Post Rest-Potentiation in Force Decay

Background: Post-rest contraction (PRC) of cardiac muscle provides indirect information about the intracellular calcium handling. Objective: Our aim was to study the behavior of PRC, and its underlying mechanisms, in rats with myocardial infarction. Methods: Six weeks after coronary occlusion, the contractility of papillary muscles (PM) obtained from sham-operated (C, n = 17), moderate infarcted (MMI, n = 10) and large infarcted (LMI, n = 14) rats was evaluated, following rest intervals of 10 to 60 seconds before and after incubation with lithium chloride (Li+) substituting sodium chloride or ryanodine (Ry). Protein expression of SR Ca(2+)-ATPase (SERCA2), Na+/Ca2+ exchanger (NCX), phospholamban (PLB) and phospho-Ser(16)-PLB were analyzed by Western blotting. Results: MMI exhibited reduced PRC potentiation when compared to C. Opposing the normal potentiation for C, post-rest decays of force were observed in LMI muscles. In addition, Ry blocked PRC decay or potentiation observed in LMI and C; Li+ inhibited NCX and converted PRC decay to potentiation in LMI. Although MMI and LMI presented decreased SERCA2 (72 +/- 7% and 47 +/- 9% of Control, respectively) and phospho-Ser(16)-PLB (75 +/- 5% and 46 +/- 11%, respectively) protein expression, overexpression of NCX (175 +/- 20%) was only observed in LMI muscles. Conclusion: Our results showed, for the first time ever, that myocardial remodeling after MI in rats may change the regular potentiation to post-rest decay by affecting myocyte Ca(2+) handling proteins. (Arq Bras Cardiol 2012;98(3):243-251)

Studies of the interaction of Potassium(I), Calcium(II), Magnesium(II), and Copper(II) with Cyclosporin A

Metal ion binding properties of the immunosuppressant drug cyclosporin A have been investigated. Complexation studies in acetonitrile solution using H-1 NMR and CD spectroscopy yielded 1:1 metal-peptide binding constants (log(10)K) for potassium(l), < 1, magnesium(II), 4.8 +/- 0.2. and calcium(II), 5.0 +/- 1.0. The interaction of copper(II) with cyclosporin A in methanol was investigated with UV/visible and electron paramagnetic resonance (EPR) spectroscopy. No complexation of copper(II) was observed in neutral solution. In the presence of base, monomeric copper(II) complexes were detected. These results support the possibility that cyclosporin A has ionophoric properties for biologically important essential metal ions. (C) 2003 Elsevier Inc. All rights reserved.

Synthesis and characterisation of vinyl block copolymers

A study has been made of the anionic polymerisation of methyl methacrylate using butyllithium and polystyryl lithium as initiators and the effects of lithium chloride and aluminium alkyls on the molecular weight and molecular weight distributions. Diblock copolymers of styrene-b-methyl methacrylate were synthesised at -78oC in THF in the presence of lithium chloride, and at ambient temperatures in toluene in the presence of aluminium alkyls. Studies in the presence of lithium chloride showed that the polymerisation was difficult to control; there was no conclusive evidence of a living system and the polydispersity indices were between 1.5 and 3. However, using relatively apolar solvents, in the presence of aluminium alkyls, homopolymerisation of methyl methacrylate showed characteristics of a living polymerisation. An investigation of the effects of the structures of the lithium and aluminium alkyls on the efficiency of initiation showed that a t-butyllithium/triisobutylaluminium initiating system exhibited an efficiency of 80%, compared with lower efficiencies (typically 30%) for systems based on butyllithium/triethylaluminium.The polydispersity index was found to decrease from ∼2.2 to ∼1.5 when butyllithium was replaced by t-butyllithium. The efficiency of the initiator was found to be solely dependent on the size of the alkyl group of the aluminium component, whereas the polydispersity index was found to be solely dependent on the size of the alkyl group on the lithium component. The aluminium alkyl is thought to be co-ordinated to the ester carbonyl groups of both the monomer and polymer. There is a critical degree of polymerisation, at which point the rate of polymerisation decreases, which probably relates to a change in structure of the active chain end. Characterisation of poly(styrene )-b-poly(4-vinylpyridine) and poly(styrene)-b-poly(4-vinylpyridine methyl iodide) diblock copolymers using static light scattering techniques, showed the formation of star-shaped 'reverse' micelles when placed in toluene. Temperature effects on micellization behaviour are only exhibited for the unquaternised micelles, which showed characterisically lower aggregation numbers than their quaternised counterparts. A suitable solvent was not obtained for characterisation of the styrene-b-methyl methacrylate diblock copolymers synthesized.

Rôle du facteur de transcription PITX1 dans les pathogenèses de l'ostéoporose et des maladies parodontales

L’ostéoporose est une maladie caractérisée par une faible masse osseuse et une détérioration du tissu osseux. Cette condition entraîne une plus grande fragilité osseuse et des risques de fractures. Plusieurs études ont associé l’ostéoporose à la faible densité osseuse des mandibules, à la perte d’attache parodontale, à l’augmentation de la hauteur de la crête alvéolaire et à la chute des dents. Cette étude vise à comprendre les mécanismes sous-jacents cette perte osseuse. En effet, au cours du développement des souris, PITX1 joue un rôle clé dans l'identité des membres postérieurs et dans le bon développement des mandibules et des dents. Son inactivation complète chez la souris mène à un phénotype squelettique sévère. Tandis que, son inactivation partielle provoque des symptômes apparentés à l'arthrose avec une augmentation de la masse osseuse au niveau de l’os cortical et de l’os trabéculaire. Inversement, une étude antérieure chez des jumelles monozygotiques discordantes pour l’ostéoporose, montrent une augmentation d’environ 8.6 fois du niveau d’expression du gène Pitx1 chez la jumelle ostéoporotique. Collectivement, ces données nous ont poussés à investiguer sur le rôle du facteur de transcription PITX1 dans le métabolisme osseux normal et pathologique. Dans ce contexte, des souris transgéniques Col1α1-Pitx1 sur-exprimant Pitx1 spécifiquement dans le tissu osseux sous le promoteur du collagène de type-I (fragment 2.1kpb) ont été générées et phénotypiquement caractérisées. Ces résultats ont révelé que les souris transgéniques Col1α1-Pitx1 présentaient un phénotype similaire à celui des patients ostéoporotiques accompagné d'une perte de dents et des problèmes dentaires et parodontaux. De plus, cette étude a révélé que la surexpression de Pitx1 induit une altération de l’homéostasie osseuse via l’inactivation de la voie de signalisation Wnt/β-caténine canonique. Cette hypothèse a été appuyée par le fait que le traitement des souris transgéniques Col1α1-Pitx1 avec du chlorure de lithium, un activateur de la voie Wnt canonique, prévient le phénotype ostéoporotique chez ces souris. Finalement, cette étude établit un rôle crucial de PITX1 dans la régulation de la masse osseuse et une implication possible dans l’ostéoporose et les maladies parodontales via l’inactivation de la voie de signalisation Wnt/β-caténine canonique.

Greener Alternatives to Selected Organic Oxidation Reactions

The study of green chemistry is dedicated to eliminating or reducing toxic waste. One route to accomplish this goal is to explore alternative reaction conditions and parameters resulting in the development of more benign synthetic routes and reagents. The primary focus of this research is to find optimal reaction conditions for the oxidation of a primary alcohol to an aldehyde. As a case study, the oxidation of benzyl alcohol to benzaldehyde, a common industrial process, was examined. Traditionally carried out using the Jones Reagent, commonly referred to as chromium (IV) oxide or chromium trioxide (CrO3) in sulphuric acid, a great deal of research went into utilizing less toxic reagents, such as MnO2 or KMnO4 supported on a clay base. This research has led to an improvement on these alternatives, using a lithium chloride (LiCl) catalyst in a montmorillonite K10 clay solid phase, together with the oxidizing agent hydrogen peroxide, as even greener alternatives to these traditional oxidizing agents. Experiments were carried out to determine the lifetime of this LiCl/clay system as compared to MnO2 and KMnO4, to investigate its ability to catalyze the oxidation of other aromatic alcohols (such as 4-methoxybenzyl alcohol and diphenylmethanol), and to further improve the system’s adherence to green chemistry principles. Green solvent alternatives were examined by replacing the toluene solvent with dimethylcarbonate (DMC), and reaction conditions were optimized to improve product yield. It was determined that the LiCl/H2O2 system was, in most cases, equally as effective at catalyzing the oxidation of benzyl alcohol to benzaldehyde. Although the catalyst and oxidizing agent eliminated the toxic waste generated from chromium reagents, it offered significant challenges in product isolation, because of an aqueous-organic phase separation.

Rôle du facteur de transcription PITX1 dans les pathogenèses de l'ostéoporose et des maladies parodontales

L’ostéoporose est une maladie caractérisée par une faible masse osseuse et une détérioration du tissu osseux. Cette condition entraîne une plus grande fragilité osseuse et des risques de fractures. Plusieurs études ont associé l’ostéoporose à la faible densité osseuse des mandibules, à la perte d’attache parodontale, à l’augmentation de la hauteur de la crête alvéolaire et à la chute des dents. Cette étude vise à comprendre les mécanismes sous-jacents cette perte osseuse. En effet, au cours du développement des souris, PITX1 joue un rôle clé dans l'identité des membres postérieurs et dans le bon développement des mandibules et des dents. Son inactivation complète chez la souris mène à un phénotype squelettique sévère. Tandis que, son inactivation partielle provoque des symptômes apparentés à l'arthrose avec une augmentation de la masse osseuse au niveau de l’os cortical et de l’os trabéculaire. Inversement, une étude antérieure chez des jumelles monozygotiques discordantes pour l’ostéoporose, montrent une augmentation d’environ 8.6 fois du niveau d’expression du gène Pitx1 chez la jumelle ostéoporotique. Collectivement, ces données nous ont poussés à investiguer sur le rôle du facteur de transcription PITX1 dans le métabolisme osseux normal et pathologique. Dans ce contexte, des souris transgéniques Col1α1-Pitx1 sur-exprimant Pitx1 spécifiquement dans le tissu osseux sous le promoteur du collagène de type-I (fragment 2.1kpb) ont été générées et phénotypiquement caractérisées. Ces résultats ont révelé que les souris transgéniques Col1α1-Pitx1 présentaient un phénotype similaire à celui des patients ostéoporotiques accompagné d'une perte de dents et des problèmes dentaires et parodontaux. De plus, cette étude a révélé que la surexpression de Pitx1 induit une altération de l’homéostasie osseuse via l’inactivation de la voie de signalisation Wnt/β-caténine canonique. Cette hypothèse a été appuyée par le fait que le traitement des souris transgéniques Col1α1-Pitx1 avec du chlorure de lithium, un activateur de la voie Wnt canonique, prévient le phénotype ostéoporotique chez ces souris. Finalement, cette étude établit un rôle crucial de PITX1 dans la régulation de la masse osseuse et une implication possible dans l’ostéoporose et les maladies parodontales via l’inactivation de la voie de signalisation Wnt/β-caténine canonique.

STUDY ON DEPOSITION POTENTIALS OF LITHIUM AND SODIUM-IONS AND DEPOLARIZATION IN BINARY CHLORIDE

Deposition potentials of Lithium and Sodium ions have been measured in binary chloride systems (LiCl-KCl, NaCl-KCl) by I-V curve method, to provide a theoretical base for preparing high purity Al-Li alloy by electrolysis in molten salt. The changes of free energy and enthalpy were calculated in terms of depolarization values on Al cathode. Thermodynamic meaning of depolarization was discussed in details and the empirical relation between binary alloy type and depolarization type was proposed. It is shown for the first time that the presence of a third element in Al-Li alloy can strengthen depolarization of Li ion at Al alloy cathode and give foundation for preparing high purity Al-Li-M ternary alloy. The effect of LiCl concentration on deposition potentials of Li ion at Al cathode in KCl-LiCl melt was studied and average active coefficient of LiCl was obtained.

Potassium phosphate as a reagent for the gravimetric estimation of lithium

Previous attempts for the quantitative estimation of lithium as orthophosphate, employing an alkali metal phosphate, have not been successful. A method, is described for the estimation of lithium as trilithium phosphate from 60% ethyl alcohol solution at 65° to 70° C., employing potassium phosphate reagent, at pH 9.5. The method is applicable in the presence of varying amounts of sodium and/or potassium cations and chloride, sulfate, nitrate, and phosphate anions.