Twin peak distribution of electron emission profile and impact ionization of ambient molecules during laser ablation of silver target

Laser-induced plasma generated from a silver target under partial vacuum conditions using the fundamental output of nanosecond duration from a pulsed Nd:yttrium aluminum garnet laser is studied using a Langmuir probe. The time of flight measurements show a clear twin peak distribution in the temporal profile of electron emission. The first peak has almost the same duration as the laser pulse while the second lasts for several microseconds. The prompt electrons are energetic enough ('60 eV) to ionize the ambient gas molecules or atoms. The use of prompt electron pulses as sources for electron impact excitation is demonstrated by taking nitrogen, carbon dioxide, and argon as ambient gases.

Anomalous profile of a self-reversed resonance line from Ba+ in a laser produced plasma from YBa2Cu307

A laser produced plasma from the multielement solid target YBa2Cu3O7 is generated using 1.06 μm, 9 ns pulses from a Q-switched Nd:YAG laser in air at atmospheric pressure. A time resolved analysis of the profile of the 4554.03 Å resonance line emission from Ba II at various laser power densities has been carried out. It has been found that the line has a profile which is strongly self-reversed. It is also observed that at laser power densities equal to or exceeding 1.6×1011 W cm−2, a third peak begins to develop at the centre of the self-reversed profile and this has been interpreted as due to the anisotropic resonance scattering (fluorescence). The number densities of singly ionized barium ions evaluated from the width of the resonance line as a function of time delay with respect to the beginning of the laser pulse give typical values of the order of 1019 cm−3. The higher ion concentrations existing at smaller time delays are seen to decrease rapidly. The Ba II ions in the ground state resonantly absorb the radiation and this absorption is maximum around 120 ns after the laser pulse.

Femtosecond laser ablation on dental hard tissues-Analysis of ablated profile near an interface using local effective intensity

This study evaluated the process of ablation produced by a Ti:Sapphire femtosecond laser under different average powers taking place at the enamel/dentin interface. Based on the geometry of ablated microcavities the effective intensity for ablation was obtained. This study shows the validity for the local effective intensity analysis and allows a quantification of the variation in the ablation geometry taking place at the interface of two naturally different materials. It shows that the variation of the diameter of the ablated region as a function of the cavity depth comes essentially from a mechanism of effective intensity attenuation, as a result of a series of complex effects. Additionally, our data are sufficient to predict that a discontinuity on the ablation profile will occur on the interface between two biological media: enamel-dentin, showing a suddenly jump on the ablated cavity dimensions.

Femtosecond laser ablation on dental hard tissues-Analysis of ablated profile near an interface using local effective intensity

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

A semi-automatic method for indirect orientation of aerial images using ground control lines extracted from airborne laser scanner data

This paper presents a method for indirect orientation of aerial images using ground control lines extracted from airborne Laser system (ALS) data. This data integration strategy has shown good potential in the automation of photogrammetric tasks, including the indirect orientation of images. The most important characteristic of the proposed approach is that the exterior orientation parameters (EOP) of a single or multiple images can be automatically computed with a space resection procedure from data derived from different sensors. The suggested method works as follows. Firstly, the straight lines are automatically extracted in the digital aerial image (s) and in the intensity image derived from an ALS data-set (S). Then, correspondence between s and S is automatically determined. A line-based coplanarity model that establishes the relationship between straight lines in the object and in the image space is used to estimate the EOP with the iterated extended Kalman filtering (IEKF). Implementation and testing of the method have employed data from different sensors. Experiments were conducted to assess the proposed method and the results obtained showed that the estimation of the EOP is function of ALS positional accuracy.

Analisi geomorfologica della duna di Lido di Classe in seguito ad un evento di mareggiata, mediante monitoraggio con tenica laser scanner

L’obiettivo di questa tesi è presentare una tecnica di monitoraggio applicabile alle dune costiere, utilizzata per questo studio nella provincia di Ravenna e in particolare su di un cordone trasversale di duna costiera presente nell’area naturale adiacente alla foce del torrente Bevano nella zona di Lido di Classe. Tale tecnica si avvale dell’uso di tecnologia laser per fornire una documentazione 3D estremamente dettagliata, il quale ci permetterà di valutare come il sistema dunale si comporta di fronte ad un evento climatico estremo e/o sotto l’azione delle mareggiate, confrontando sia l’aspetto morfologico che morfometrico mediante l’uso di programmi che ci hanno permesso di confrontare i dati ottenuti prima e dopo l’evento climatico

Surface quality of profile extrusion dies manufactured by Selective Laser Melting

The design of plastics profile extrusion dies becomes increasingly more complex so that conventional manufacture processes reach their limit in the die manufacture. A feasible manufacture of arbitrarily designed dies is only possible by additive manufacturing. An especially promising process is hereby the Selective Laser Melting with which metal parts with series identical mechanical properties can be produced without the need for part specific tooling or downstream sintering processes. Disadvantegeous is, however, the relatively rough surface of additively manufactured parts. Against this background, the manufacturing of an profile extrusion die by Selective Laser Melting and the plastics profile surface quality, that can be achieved with such dies, is investigated. For this purpose, profiles are extruded both with an additively manufactured die and a conventionally milled sample of the same die geometry. In case of the additively manufactured die a concept for the surface finishing of the flow channel is required, which can be applied to arbitrarily shaped geometries. Therefore, two different reworking processes are applied only to the die land of the flow channel. The comparison of the surface roughnesses shows that the additively manufactured die with a polished die land delivers the same surface quality as the conventional die.

Effect of fibre base and reflectors profile on the efficiency of ultra- long laser cavities

We study the effect of fibre base and grating profile on the efficiency of ultra-long Raman lasers. We show that for the studied parameters, FBG profile does not affect the performance when operating away from the zero-dispersion wavelength.

Effect of fibre base and reflectors profile on the efficiency of ultra- long laser cavities

We study the effect of fibre base and grating profile on the efficiency of ultra-long Raman lasers. We show that for the studied parameters, FBG profile does not affect the performance when operating away from the zero-dispersion wavelength.