Método para análise da interação fluido-estrutura em travessas do pré-distribuidor de turbinas hidráulicas.

Um dos grandes desafios enfrentados pelos fabricantes de turbinas hidráulicas é prevenir o aparecimento de vibrações induzidas pelo escoamento nas travessas do pré-distribuidor e pás do rotor. Considerando apenas as travessas, e atribuídos a tais vibrações, foram relatados 28 casos de trincas ou ruídos anormais nas últimas décadas, que acarretaram enormes prejuízos associados a reparos, atrasos e perda de geração. O estado da arte na prevenção destes problemas baseia-se na utilização de sofisticados, e caros, programas comerciais de dinâmica dos fluidos computacional para o cálculo transiente do fenômeno. Este trabalho faz uma ampla revisão bibliográfica e levantamento de eventos de trincas ou ruídos ocorridos em travessas nos últimos 50 anos. Propõe, então, um enfoque alternativo, baseado exclusivamente em ferramentas de código aberto. A partir de hipóteses simplificadoras devidamente justificadas, o problema é formulado matematicamente de forma bidimensional, no plano da seção transversal da travessa, levando em conta a interação fluido-estrutura. Nesta estratégia, as equações de Navier-Stokes são resolvidas pelo método dos elementos finitos por meio da biblioteca gratuita oomph-lib. Um código especial em C++ é desenvolvido para o problema de interação fluido-estrutura, no qual o fenômeno de turbulência é levado em consideração por meio de um algoritmo baseado no modelo de Baldwin-Lomax. O método proposto é validado por meio da comparação dos resultados obtidos com referências e medições disponíveis na literatura, que tratam de problemas de barras retangulares suportadas elasticamente. O trabalho finaliza com a aplicação do método a um estudo de caso envolvendo uma travessa particular.

Pelton impulse & reaction turbine installations.

Mode of access: Internet.

Test of a twelve thousand horse power turbine /

Thesis (M.M.E.)--Cornell University, 1906.

Der Turbinenrechenschieber und seine Anwendung zur Projektierung von Wasserkraftanlagen.

Mode of access: Internet.

A cyclostationary multi-domain analysis of fluid instability in Kaplan turbines

Hydraulic instabilities represent a critical problem for Francis and Kaplan turbines, reducing their useful life due to increase of fatigue on the components and cavitation phenomena. Whereas an exhaustive list of publications on computational fluid-dynamic models of hydraulic instability is available, the possibility of applying diagnostic techniques based on vibration measurements has not been investigated sufficiently, also because the appropriate sensors seldom equip hydro turbine units. The aim of this study is to fill this knowledge gap and to exploit fully, for this purpose, the potentiality of combining cyclostationary analysis tools, able to describe complex dynamics such as those of fluid-structure interactions, with order tracking procedures, allowing domain transformations and consequently the separation of synchronous and non-synchronous components. This paper will focus on experimental data obtained on a full-scale Kaplan turbine unit, operating in a real power plant, tackling the issues of adapting such diagnostic tools for the analysis of hydraulic instabilities and proposing techniques and methodologies for a highly automated condition monitoring system. © 2015 Elsevier Ltd.

Influence of the Blade Hub Geometry on the Performance of Low-Head Axial Flow Turbines

The influence of geometric parameters, such as blade profile and hub geometry on axial flow turbines for micro hydro application remains poorly characterized. This paper first introduces a holistic theoretical model for studying the hydraulic phenomenon resulting from geometric modification to the blades. It then describes modification carried out on two runner stages, of which one has untwisted blades and the other has twisted blades obtained by modifying the inlet hub. The experimental results showed that the performance of the untwisted blade runner was satisfactory with a maximum efficiency of 68%. However, positive effects of twisted blades were clearly evident with an efficiency rise of more than 2%. This study also looks into the possible limitations of the model and suggests the extension of the experimental work and the use of computational tools to conduct a progressive validation of all experimental findings, especially on the flow physics within the hub region and the slip phenomena. The paper finally underlines the importance of developing a standardization philosophy for axial flow turbines specific for micro hydro requirements. DOI:10.1061/(ASCE)EY.1943-7897.0000060. (C) 2012 American Society of Civil Engineers.

Lowell hydraulic experiments, being a selection from experiments on hydraulic motors, on the flow of water over weirs, and in canals of uniform rectangular section and of short length.

Mode of access: Internet.

Experimental evaluation of position control methods for hydraulic systems

Presents a unified and systematic assessment of ten position control strategies for a hydraulic servo system with single-ended cylinder driven by a proportional directional control valve. We aim at identifying those methods that achieve better tracking, have a low sensitivity to system uncertainties, and offer a good balance between development effort and end results. A formal approach for solving this problem relies on several practical metrics, which is introduced herein. Their choice is important, as the comparison results between controllers can vary significantly, depending on the selected criterion. Apart from the quantitative assessment, we also raise aspects which are difficult to quantify, but which must stay in attention when considering the position control problem for this class of hydraulic servo systems.

Geometric and force relationships for the development of a scaled model hydraulic excavator

Hydraulic excavators in the mining industry are widely used owing to the large payload capabilities these machines can achieve. However, there are very few optimisation studies for producing efficient hydraulic excavator backets. An efficient bucket can avoid unnecessary weight; greatly influence the payload and optimise the efficiency of hydraulic mining excavators. This paper presents a framework for the development of a scaled hydraulic excavator by examining the geometry and force relationships. A small hydraulic excavator was purchased and fitted with a broom scaled to a factor. Geometric and force relationships of the model were derived to assist computer instrumentation to retrieve necessary variable input for bucket design.

Coordinated tuning of DFIG-based wind turbines and batteries using bacteria foraging technique for maintaining constant grid power output

This paper proposes the use of battery energy storage (BES) system for the grid-connected doubly fed induction generator (DFIG). The BES would help in storing/releasing additional power in case of higher/lower wind speed to maintain constant grid power. The DC link capacitor is replaced with the BES system in a DFIG-based wind turbine to achieve the above-mentioned goal. The control scheme is modified and the co-ordinated tuning of the associated controllers to enhance the damping of the oscillatory modes is presented using bacterial foraging technique. The results from eigenvalue analysis and the time domain simulation studies are presented to elucidate the effectiveness of the BES systems in maintaining the grid stability under normal operation.

Preliminary Design and Performance Estimation of Radial Inflow Turbines: An Automated Approach

A comprehensive one-dimensional meanline design approach for radial inflow turbines is described in the present work. An original code was developed in Python that takes a novel approach to the automatic selection of feasible machines based on pre-defined performance or geometry characteristics for a given application. It comprises a brute-force search algorithm that traverses the entire search space based on key non-dimensional parameters and rotational speed. In this study, an in-depth analysis and subsequent implementation of relevant loss models as well as selection criteria for radial inflow turbines is addressed. Comparison with previously published designs, as well as other available codes, showed good agreement. Sample (real and theoretical) test cases were trialed and results showed good agreement when compared to other available codes. The presented approach was found to be valid and the model was found to be a useful tool with regards to the preliminary design and performance estimation of radial inflow turbines, enabling its integration with other thermodynamic cycle analysis and three-dimensional blade design codes.