An analysis of the effect of process parameters on the formability of sheet metal

This investigation is in two parts, theory and experimental verification. (1) Theoretical Study In this study it is, for obvious reasons, necessary to analyse the concept of formability first. For the purpose of the present investigation it is sufficient to define the four aspects of formability as follows: (a) the formability of the material at a critical section, (b) the formability of the material in general, (c) process efficiency, (d) proportional increase in surface area. A method of quantitative assessment is proposed for each of the four aspects of formability. The theoretical study also includes the distinction between coaxial and non-coaxial strains which occur, respectively, in axisymmetrical and unsymmetrical forming processes and the inadequacy of the circular grid system for the assessment of formability is explained in the light of this distinction. (2) Experimental Study As one of the bases of the experimental work, the determination of the end point of a forming process, which sets the limit to the formability of the work material, is discussed. The effects of three process parameters on draw-in are shown graphically. Then the delay of fracture in sheet metal forming resulting from draw-in is analysed in kinematical terms, namely, through the radial displacements, the radial and the circumferential strains, and the projected thickness of the workpiece. Through the equilibrium equation of the membrane stresses, the effect on the shape of the unsupported region of the workpiece, and hence the position of the critical section is explained. Then, the effect of draw-in on the four aspects of formability is discussed throughout this investigation. The triangular coordinate system is used to present and analyse the triaxial strains involved. This coordinate system has the advantage of showing all the three principal strains in a material simultaneously, as well as representing clearly the many types of strains involved in sheet metal work.

Caractérisation des propriétés mécaniques de la pâte de carbone à 150°C dans le but d’optimiser la mise en forme des anodes utilisées dans les cuves Hall-Héroult

Les anodes de carbone sont des éléments consommables servant d’électrode dans la réaction électrochimique d’une cuve Hall-Héroult. Ces dernières sont produites massivement via une chaine de production dont la mise en forme est une des étapes critiques puisqu’elle définit une partie de leur qualité. Le procédé de mise en forme actuel n’est pas pleinement optimisé. Des gradients de densité importants à l’intérieur des anodes diminuent leur performance dans les cuves d’électrolyse. Encore aujourd’hui, les anodes de carbone sont produites avec comme seuls critères de qualité leur densité globale et leurs propriétés mécaniques finales. La manufacture d’anodes est optimisée de façon empirique directement sur la chaine de production. Cependant, la qualité d’une anode se résume en une conductivité électrique uniforme afin de minimiser les concentrations de courant qui ont plusieurs effets néfastes sur leur performance et sur les coûts de production d’aluminium. Cette thèse est basée sur l’hypothèse que la conductivité électrique de l’anode n’est influencée que par sa densité considérant une composition chimique uniforme. L’objectif est de caractériser les paramètres d’un modèle afin de nourrir une loi constitutive qui permettra de modéliser la mise en forme des blocs anodiques. L’utilisation de la modélisation numérique permet d’analyser le comportement de la pâte lors de sa mise en forme. Ainsi, il devient possible de prédire les gradients de densité à l’intérieur des anodes et d’optimiser les paramètres de mise en forme pour en améliorer leur qualité. Le modèle sélectionné est basé sur les propriétés mécaniques et tribologiques réelles de la pâte. La thèse débute avec une étude comportementale qui a pour objectif d’améliorer la compréhension des comportements constitutifs de la pâte observés lors d’essais de pressage préliminaires. Cette étude est basée sur des essais de pressage de pâte de carbone chaude produite dans un moule rigide et sur des essais de pressage d’agrégats secs à l’intérieur du même moule instrumenté d’un piézoélectrique permettant d’enregistrer les émissions acoustiques. Cette analyse a précédé la caractérisation des propriétés de la pâte afin de mieux interpréter son comportement mécanique étant donné la nature complexe de ce matériau carboné dont les propriétés mécaniques sont évolutives en fonction de la masse volumique. Un premier montage expérimental a été spécifiquement développé afin de caractériser le module de Young et le coefficient de Poisson de la pâte. Ce même montage a également servi dans la caractérisation de la viscosité (comportement temporel) de la pâte. Il n’existe aucun essai adapté pour caractériser ces propriétés pour ce type de matériau chauffé à 150°C. Un moule à paroi déformable instrumenté de jauges de déformation a été utilisé pour réaliser les essais. Un second montage a été développé pour caractériser les coefficients de friction statique et cinétique de la pâte aussi chauffée à 150°C. Le modèle a été exploité afin de caractériser les propriétés mécaniques de la pâte par identification inverse et pour simuler la mise en forme d’anodes de laboratoire. Les propriétés mécaniques de la pâte obtenues par la caractérisation expérimentale ont été comparées à celles obtenues par la méthode d’identification inverse. Les cartographies tirées des simulations ont également été comparées aux cartographies des anodes pressées en laboratoire. La tomodensitométrie a été utilisée pour produire ces dernières cartographies de densité. Les résultats des simulations confirment qu’il y a un potentiel majeur à l’utilisation de la modélisation numérique comme outil d’optimisation du procédé de mise en forme de la pâte de carbone. La modélisation numérique permet d’évaluer l’influence de chacun des paramètres de mise en forme sans interrompre la production et/ou d’implanter des changements coûteux dans la ligne de production. Cet outil permet donc d’explorer des avenues telles la modulation des paramètres fréquentiels, la modification de la distribution initiale de la pâte dans le moule, la possibilité de mouler l’anode inversée (upside down), etc. afin d’optimiser le processus de mise en forme et d’augmenter la qualité des anodes.

Effects of hot and cold smoking processes on organoleptic properties, yield and composition of matrinxa fillet

Foi avaliado o efeito do processo de defumação a quente (45-90ºC/5 horas) e a frio (27-45ºC/10 horas) nas propriedades organolépticas, no rendimento e na composição dos filés de matrinxã (Brycon cephalus). Não houve diferença significativa no rendimento de filés defumados e não-defumados. As perdas no processo de defumação foram significativamente maiores para defumação a quente (19,37%) em comparação à defumação a frio (17,08%). O processo de defumação reduziu a umidade (in natura = 72,91%; defumado a quente = 58,51%; e defumado a frio = 59,68%) e aumentou os teores de proteína bruta, lipídios e cinzas. Houve diferença significativa somente nos teores de proteína no defumado a quente (28,07%) e defumado a frio (27,14%). O processo a frio resultou em melhor aparência e cor de filé, enquanto o processo a quente melhorou o sabor, o teor de sal e a aparência geral. O aroma e a textura não diferiram significativamente entre os processos. O processo de defumação a quente melhora as propriedades organolépticas e os níveis de proteína do filé de matrinxã.

Dynamic mechanical-thermal, microstructural and mechanical analysis of ultra-light polymer-metal composites: influence of forming

A really particular and innovative metal-polymer sandwich material is Hybrix. Hybrix is a product developed and manufactured by Lamera AB, Gothenburg, Sweden. This innovative hybrid material is composed by two relatively thin metal layers if compared to the core thickness. The most used metals are aluminum and stainless steel and are separated by a core of nylon fibres oriented perpendicularly to the metal plates. The core is then completed by adhesive layers applied at the PA66-metal interface that once cured maintain the nylon fibres in position. This special material is very light and formable. Moreover Hybrix, depending on the specific metal which is used, can achieve a good corrosion resistance and it can be cut and punched easily. Hybrix architecture itself provides extremely good bending stiffness, damping properties, insulation capability, etc., which again, of course, change in magnitude depending in the metal alloy which is used, its thickness and core thickness. For these reasons nowadays it shows potential for all the applications which have the above mentioned characteristic as a requirement. Finally Hybrix can be processed with tools used in regular metal sheet industry and can be handled as solid metal sheets. In this master thesis project, pre-formed parts of Hybrix were studied and characterized. Previous work on Hybrix was focused on analyze its market potential and different adhesive to be used in the core. All the tests were carried out on flat unformed specimens. However, in order to have a complete description of this material also the effect of the forming process must be taken into account. Thus the main activities of the present master thesis are the following: Dynamic Mechanical-Thermal Analysis (DMTA) on unformed Hybrix samples of different thickness and on pre-strained Hybrix samples, pure epoxy adhesive samples analysis and finally moisture effects evaluation on Hybrix composite structure.

A formação pela trilha da clínica da atividade na vigilância em saúde do trabalhador

Trata-se de uma pesquisa-intervenção com o objetivo principal de colocar em análise a atividade na vigilância em saúde do trabalhador ancorada nos pressupostos da formação pelo trabalho. Tem como aporte conceitual o referencial teórico-metodológico da clínica da atividade proposta por Yves Clot e colaboradores. A pesquisa foi realizada com a equipe multiprofissional que atua na vigilância em saúde do trabalhador do Centro de Referência Estadual em Saúde do Trabalhador do Espírito Santo (Cerest/ES). As rodas de conversa, a partir da clínica da atividade, foram a estratégia metodológica privilegiada. O gênero profissional vigilante em saúde do trabalhador, ao se confrontar com o estudo das diretrizes da clínica da atividade, foi produzindo deslocamentos que o levou a (re)pensar, analisar a sua atividade e o processo de trabalho no qual estava inserido. A cada encontro no diálogo com a clínica da atividade, eram experimentados os modos de como esses profissionais atuavam na vigilância, como também todo o atravessamento desse gênero na assistência aos trabalhadores, nas atividades educativas e gestão do trabalho. No desenvolvimento das rodas, ficou evidenciado o quanto esses encontros se tornaram equipamentos para esses profissionais. As atividades desenvolvidas produziram análise coletiva do trabalho e um processo de formação pelo trabalho. Buscaram incorporar os métodos utilizados pela clínica da atividade no cotidiano do Cerest dialogando com os efeitos desse processo. Nas rodas também emergiram propostas de mudanças na maneira como vinham ocorrendo as atividades realizadas, a gestão do trabalho nessa equipe e as estratégias de atuação na vigilância, ou seja, intervenção no processo de trabalho do grupo, produzindo potência para o poder de agir do gênero. O referencial teórico-metodológico da clínica da atividade foi um dispositivo de formação importante. Permitiu a experimentação e o desenvolvimento do gênero vigilantes em saúde do trabalhador na produção de análise da atividade, na constituição de uma clínica dialógica em transformação. Também possibilitou contemplar na análise as dimensões integrantes da atividade de trabalho, fazendo a interlocução para o encontro entre os saberes da experiência instituídos no cotidiano do serviço de saúde e o saber acadêmico na produção de conhecimento.

Estudo de Ferramentas FEA Comerciais na Simulação Numérica de Processos de Conformação de Chapas Metálicas. Aplicação à Indústria Automóvel.

Os componentes obtidos através da conformação plástica de chapas têm uma grande importância, tanto na etapa de concepção do produto como na etapa de produção na indústria automóvel. Isto comprova-se pelo facto de, em média, cada automóvel integrar cerca de 500 componentes estampados para construir o chassis e a carroçaria [Alves 2003]. Deste total de componentes, 50 são de grandes dimensões (portas, tejadilho, painéis inferior e laterais, entre outros) e necessitam, em média, de cinco ferramentas para o seu fabrico, sendo o custo estimado para cada ferramenta de 230 000 € [Col 2000, Alves 2003]. Para além da indústria automóvel, a conformação plástica de chapas metálicas é um processo tecnológico presente nas indústrias relativas à aeroespacial, petrolífera, decoração, alimentar, entre outras. Do ponto de vista do enquadramento económico, cerca de 20% do custo total de um automóvel novo é devido à incorporação de componentes metálicos estampados. [Alves 2003]. A pressão do “Mercado Global” faz com que os custos relativos à matéria-prima, energia e mão-de-obra sejam uma constante em termos de redução do seu impacte no orçamento das empresas fornecedoras destes produtos. É neste contexto que surge a necessidade da realização deste estudo de Benchmark de Softwares, tornando-se bastante importante, quer ao nível da competitividade industrial, quer ao nível da inovação para novos produtos. A análise por elementos finitos desempenha um papel primordial no tryout virtual e otimização das ferramentas e processos de conformação plástica. Os objetivos principais deste estudo de simulação numérica são a identificação e comparação dos resultados obtidos pelo AUTOFORM e pelo PAMSTAMP, para cada uma das variáveis identificadas como as mais influentes na robustez dos processos de estampagem de chapa metálica. Estas variáveis identificadas são: consumo de material (Draw-in) após conformação; forças de conformação; valores de variação de espessura e dos valores de extensão e resultados de Springback. Os resultados obtidos são comparados com os resultados experimentais e, desta forma, avalia-se a capacidade inovadora e a eficácia de cada um dos softwares, obtendo-se assim, uma orientação mais real para o software mais indicado aos objetivos impostos pela indústria automóvel. Para este efeito, a indústria automóvel, como maior impulsionador e motor da investigação na área da simulação numérica aplicada aos processos de estampagem, tem aderido em peso ao Benchmarking. Um exemplo disto, é o que acontece nas conferências Numisheet. O Benchmark #2 da conferência Numisheet 2008 é analisado pormenorizadamente e os resultados numéricos e experimentais são comparados e apresentados. Dois materiais distintos (aço HC260LAD e liga de alumínio AC170), assim como três modelos com geometrias diferentes (com e sem freios) são apresentados neste relatório. Com vista à redução dos ciclos tentativa-erro, tem-se adotado ciclos virtuais ou numéricos e tem-se incrementado a interatividade entre as fases de concepção e projeto, num conceito muito próprio, mas cada vez mais abrangente, denominado “produção virtual”. É nesta filosofia que se insere a simulação numérica dos processos de conformação de chapa.

Determination of Asphalt Content and Characteristics of Bituminous Paving Mixtures, MLR-88-11, 1988

Due to the hazardous nature of chemical asphalt extraction agents, nuclear gauges have become an increasingly popular method of determining the asphalt content of a bituminous mix. This report details the results of comparisons made between intended, tank stick, extracted, and nuclear asphalt content determinations. A total of 315 sets of comparisons were made on samples that represented 110 individual mix designs and 99 paving projects. All samples were taken from 1987 construction projects. In addition to the comparisons made, seventeen asphalt cement samples were recovered for determination of penetration and viscosity. Results were compared to similar tests performed on the asphalt assurance samples in an attempt to determine the amount of asphalt hardening that can be expected due to the hot mix process. Conclusions of the report are: 1. Compared to the reflux extraction procedure, nuclear asphalt content gauges determine asphalt content of bituminous mixes with much greater accuracy and comparable precision. 2. As a means for determining asphalt content, the nuclear procedure should be used as an alternate to chemical extractions whenever possible. 3. Based on penetration and viscosity results, softer grade asphalts undergo a greater degree 'of hardening due to hot mix processing than do harder grades, and asphalt viscosity changes caused by the mixing process are subject to much more variability than are changes in penetration. 4. Based on changes in penetration and viscosity, the Thin Film Oven Test provides a reasonable means of estimating how much asphalt hardening can be anticipated due to exposure to the hot mix processing environment.

Penetration Characteristics of Asphalt in a Recycled Mixture, MLR-79-03, 1979

Samples of both recycled and nonrecycled asphaltic concrete were extracted in increments by the Abson Recovery Method and the penetration of the asphalt from each increment determined. The recycled projects were plantsite operations containing various amounts of virgin gravel. Cored samples were taken from the pavements on Kossuth County roads that were constructed as recycled projects in 1975, 1976, and 1977. Cored samples were also taken from a Kossuth County paving project done in 1975, that was not recycled. Comparison mix samples from 1978 construction projects in Marshall and Woodbury Counties of non - recycled projects are included. The test data from the penetrations of the recovered asphalt indicates that mixing of the old and new asphalt occurs very extensively in the hot recycling process. In laboratory controlled conditions it is difficult to coat aggregates with different penetration asphalts and prevent them from mixing.

Verkottuva liiketoiminta, arvoverkosto, partneroituminen, prosessi-integraatio

Tutkielmassa tarkasteltiin muodostuvan RosettaNet-palvelun toteuttamiseen tarvittavia osaamisia ja valittiin osaamisien perusteella parhaat mahdolliset partnerit. Aluksi selvitettiin verkottuvan liiketoiminnan periaatteita sekä verkostoitumisen vaikutusta yritysten nykyiseen toimintaympäristöön. Verkostoista siirryttiin arvoverkostoihin sekä niiden sisälle muodostuvien arvontuotantojärjestelmien toimintaan, joiden pohjalta luotiin RosettaNet-palvelun ympärille muodostuva arvoverkosto ja havaittiin sen sisältävän useita erillisiä arvontuotantojärjestelmiä. Arvontuotantojärjestelmien ja empiirisen kokemuksen pohjalta hahmotettiin palveluun tarvittavat osaamiset, joita olivat teknologia-alustaosaaminen, myynti ja konsultointiosaaminen, ratkaisusuunnitteluja integraatio-osaaminen. Näiden osaamisten perusteella kartoitettiin kaikki mahdolliset partnerit, joiden kanssa tuleva palvelu voitaisiin toteuttaa. Tällöin pääkriteereinä olivat partnerin osaaminen ja sopivuus palveluntarjoajan nykyiseen toimintaympäristöön. Alustavien tutkimuskierrosten jälkeen jäljelle jääneille partneriehdokkaille suoritettiin teemahaastattelut ja yritysten taustojen selvitys. Näiden tutkimusten perusteella yritysten osaamiset ja soveltuvuudet arvioitiin ja tehtiin ehdotus siitä, kuinka Palveluntarjoajan tulisi partneroitua RosettaNet-palvelun osalta. Tutkielmassa muodostettu arvoverkosto ja sen perusteella tehty partnerikartoitus on tehty Palveluntarjoajan tarpeiden pohjalta, eikä se sellaisenaan sovellu käytettäväksi yleisenä toimintamallina johtuen jokaiselle yritykselle ominaisesta toimintaympäristöstä ja tarpeista.

Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.

Kartonkimateriaalien muotoutuvuus vuokien valmistuksessa

Diplomityön tavoitteena oli tutkia erilaisten elintarvikekartonkien muotoutuvuutta prässäämällä valmistettujen vuokien valmistuksessa. Kirjallisuusosassa käsiteltiin mm. kartongin muotoutuvuuteen vaikuttavia ominaisuuksia sekä lämpötilan ja kosteuden vaikutusta muotoutuvuuteen. Lisäksi kirjallisuusosassa käytiin läpi vuokien valmistusprosessi, jossa vuoka-aihiot valmistetaan stanssaamalla ja vuoat prässäämällä. Lopuksi on esitetty vuokien valmistuksessa kartongin muotoutuvuuteen vaikuttavia ajoparametrejä. Kokeellisessa osassa valmistettiin prässäämällä vuokia erilaisista kartonkimateriaaleista. Jokaiselle materiaalille etsittiin sopivat ajoparametrit erilaisissa kosteuspitoisuuksissa ja vertailtiin niiden muotoutuvuutta. Työ sisälsi myös kaksi laminointikoeajoa, jonka tuloksena saatuja materiaaleja verrattiin referenssi vuokakartonkiin. Vuokien todettiin muotoutuvan parhaiten kosteuden ollessa 7 – 9,4 % välillä. Työssä erottui kartongit, jotka muotoutuivat muita paremmin sekä kartongit, jotka muotoutuivat muita huonommin. Näiden muotoutuvuutta pyrittiin selvittämään mitattujen paperiteknisten ominaisuuksien avulla, mutta selvää yksittäistä selittävää ominaisuutta ei löytynyt. Parhaiten muotoutuvuutta kuvasivat kartonkien kuitukoostumukset. Laminoitujen rakenteiden todettiin muotoutuvan vuokakartonkia paremmin. Tähän vaikuttivat laminaattien korkeammat lujuus- ja venymäarvot.

Portable flow board for storage of fruits and vegetables in mini-chambers with controlled atmosphere

ABSTRACT A portable flow board system was developed in the present study with the aim to facilitate lab-scale experiments of controlled atmosphere (CA) with fruits and vegetables. This sturdy flow board combines ease fabrication, low cost and gas economy. Its functionality is provided by manifolds and gas mixers. Each gaseous component is supplied by a gas cylinder through a differential valve of adjusted pressure control, generally at 6 kPa, and forced through 13 standardized restrictors coupled to each manifold output. Controlled atmospheres are then formed with one, two or three gases in 13 gas mixers affixed to the flow board base, which are further conducted through flexible tubes to storage mini-chambers that can also be used to study metabolic consumption and production of gaseous components. The restrictors used in the flow gaseous components were manufactured from microhematocrit test-type capillary glass tubes following the hot forming method under continuous air flow. The portable flow board showed to be low cost and simple post-harvest equipment that allows preparing controlled atmospheres in open systems with stable composition and flow, in a manner similar to traditional flow boards with control of gas escape by barostats.

Application of the finite element method in cold forging processes

The demand for more efficient manufacturing processes has been increasing in the last few years. The cold forging process is presented as a possible solution, because it allows the production of parts with a good surface finish and with good mechanical properties. Nevertheless, the cold forming sequence design is very empirical and it is based on the designer experience. The computational modeling of each forming process stage by the finite element method can make the sequence design faster and more efficient, decreasing the use of conventional "trial and error" methods. In this study, the application of a commercial general finite element software - ANSYS - has been applied to model a forming operation. Models have been developed to simulate the ring compression test and to simulate a basic forming operation (upsetting) that is applied in most of the cold forging parts sequences. The simulated upsetting operation is one stage of the automotive starter parts manufacturing process. Experiments have been done to obtain the stress-strain material curve, the material flow during the simulated stage, and the required forming force. These experiments provided results used as numerical model input data and as validation of model results. The comparison between experiments and numerical results confirms the developed methodology potential on die filling prediction.

Kartongin fysikaalisten ominaisuuksien vaikutus muovautuvuuteen

Työn tavoitteena oli kehittää menetelmä, jolla voitaisiin arvioida veto-ominaisuuksien avulla konvertointikoneen prässäysnopeuden ja muottien lämpötilan vaikutuksia kartongin muovautuvuuteen. Kirjallisuusosassa käsiteltiin kartongin muovautuvuuteen vaikuttavia ominaisuuksia sekä vetolujuuteen vaikuttavia tekijöitä. Lisäksi käsiteltiin kosteuden vaikutusta muovautuvuuteen sekä esiteltiin vuokakonvertointiprosessin periaate ja muovin sekä kartongin käyttäytymisen erot konvertointiprosessissa. Kokeellinen osa jakaantui kolmeen osaan. Esikokeissa tutkittiin laboratoriomittauksilla vetonopeuden ja kosteuden muutosten vaikutusta erilaisten kaupallisten kartonkimateriaalien vetolujuuteen ja murtovenymään. Tulosten perusteella valittiin prässäysnopeudet ja kosteustaso 2D- testauslaitteella suoritettuihin esi-pilot-mittakaavan kokeisiin sekä varsinaiseen pilot-koeajoon. Pilot-koeajossa pyrittiin arvioimaan prässäysnopeuden ja muottien lämpötilan vaikutuksia muovautuvuuteen vetolujuusarvojen avulla. Prässäysnopeudella ja vetolujuuslaitteen nopeudella ei havaittu yhteneväisyyksiä, jotta voitaisiin arvioida kartongin muovautuvuutta. Muovautuvuutta voidaan kuitenkin arvioida epäonnistuneisuusluvulla, jonka laskentapa kehitettiin työn aikana. Epäonnistuneisuusluku kuvaa hyvin kartongin muovautuvuutta ja on menetelmänä helppo, mutta sen heikkoutena on repeämien mittaamisen aiheuttama epätarkkuus. Esikokeissa havaittiin myös muovipäällysteiden veto-ominaisuuksien vastaavan kartongin ominaisuuksia 65 %:n suhteellisessa kosteudessa, jonka valittiin siten olevan optimaalinen olosuhde pilot-mittakaavan koeajoihin.

Effect of ambient conditions on dimensional stability and stiffness of commercial paperboard and paperboard trays

The objective of this study was to develop laboratory test methods for characterizing the effects of changed moisture content on paperboard trays produced by press-forming process. Influence of moisture on the properties of unconverted paperboard such as bending stiffness, bursting strength, and curling was studied. Paperboard and tray samples were tested after storing in different relative humidity conditions (35, 50, 65, 80 and 95% RH). The effect of PE and PET extrusion coatings on these properties was also studied. It was found that increase in moisture content of paperboard decreases bending and bursting strength, dimensional stability and stiffness of paperboard trays. Such physical and mechanical properties as bending stiffness and curling of paperboard seem to define the stiffness of ready-made trays and their dimensional stability. Paperboards and trays with extruded PE and PET one sided coatings demonstrated higher strength properties but at the same time had lower dimensional stability comparing to uncoated paperboards. Samples with smaller polymer coat weight had better dimensional stability than respective samples with higher coat weight. It was also found that preconditioning of paperboard in lower humidity environment before press-forming could improve dimensional stability and stiffness of ready-made tray.