A Mineral Dressing and Economic Study of a Complex Arsenical Ore

The factors that influence the choice of a method for treat­ment of an ore comprise the technical and economic limitations and advantages, derived in detail and balanced according to the exigencies of the particular situation.

The role of a transcrustal shear zone in orogenic gold mineralization at the Aijanahalli Mine, Dharwar Craton, South India

The Ajjanahalli gold mine is spatially associated with a Late Archean craton-scale shear zone in the eastern Chitradurga greenstone belt of the Dharwar craton, India. Gold mineralization is hosted by an similar to100-m-wide antiform in a banded iron formation. Original magnetite and siderite are replaced by a peak metamorphic alteration assemblage of chlorite, stilpnomelane, minnesotaite, sericite, ankerite, arsenopyrite, pyrite, pyrrhotite, and gold at ca. 300degrees to 350degreesC. Elements enriched in the banded iron formation include Ca, Mg, C, S, An, As, Bi. Cu, Sb, Zn, Pb, Se, Ag, and Te, whereas in the wall rocks As, Cu, Zn, Bi, Ag, and An are only slightly enriched. Strontium correlates with CaO, MgO, CO2, and As, which indicates cogenetic formation of arsenopyrite and Mg-Ca carbonates. The greater extent of alteration in the Fe-rich banded iron formation layers than in the wall rock reflects the greater reactivity of the banded iron formation layers. The ore fluids, as interpreted from their isotopic composition (delta(18)O = 6.5-8.5parts per thousand; initial Sr-87/Sr-86 = 0.7068-0.7078), formed by metamorphic devolatilization of deeper levels of the Chitradurga greenstone belt. Arsenopyrite, chalcopyrite, and pyrrhotite have delta(34)S values within a narrow range between 2.1 and 2.7 per mil, consistent with a sulfur source in Chitradurga greenstone belt lithologies. Based on spatial and temporal relationships between mineralization, local structure development, and sinistral strike-slip deformation in the shear zone at the eastern contact of the Chitradurga greenstone belt, we suggest that the Ajjanahalli gold mineralization formed by fluid infiltration into a low strain area within the first-order structure. The ore fluids were transported along this shear zone into relatively shallow crustal levels during lateral terrane accretion and a change from thrust to transcurrent tectonics. Based on this model of fluid flow, exploration should focus on similar low strain areas or potentially connected higher order splays of the first-order shear zone.

The mineralizing fluid in the Piaba gold deposit, São Luís cratonic fragment (NW-Maranhão, Brazil) based on fluid inclusion studies in quartz veins

O depósito aurífero de Piaba tornou-se a primeira mina em operação no fragmento cratônico São Luís, noroeste do Maranhão. Seu ambiente geológico compreende rochas metavulcanossedimentares do Grupo Aurizona e granitoides da Suíte Tromaí, entre outras unidades menores, formadas em ambiente de arcos de ilhas entre 2240 e 2150 Ma, juntamente com outras unidades menores. A mineralização é caracterizada por uma trama stockwork de veios e vênulas de quartzo com seus halos de alteração (clorita + muscovita + carbonato + pirita + calcopirita e ouro) hospedada em um granodiorito granofírico fino (Granófiro Piaba) e em rocha subvulcânica andesítica do Grupo Aurizona. O corpo mineralizado é espacialmente limitado à zona de cisalhamento ENE-WSW rúptil-dúctil (Falha Piaba). Estudos petrográficos, microtermométricos e por espectroscopia microRaman no quartzo definiram inclusões aquo-carbônicas bifásicas e trifásicas, produzidas por aprisionamento heterogêneo durante separação de fases, e fluidos aquosos tardios. A solução mineralizadora corresponde a um fluido aquo-carbônico composto por CO₂ (5 - 24 mol%, densidade de 0,96 - 0,99 g/cm³), H₂O (74 - 93 mol%), N₂ (< 1 mol%), CH₄ (<1mol%) e 5,5 % em peso NaCl equivalente. O minério depositou a 267 - 302ºC e 1,25 - 2,08 kbar, correspondendo a profundidades de 4 a 7 km, em consonância com o regime estrutural. A composição e o intervalo de P-T do fluido mineralizador, combinados com o caráter redutor (log ƒ_O2 -31,3 a -34,3) e a sulfetação da rocha hospedeira, sugerem que o ouro foi transportado como um complexo sulfetado. O minério foi depositado em consequência da separação de fase, redução da atividade de enxofre e da ƒO₂ pela interação fluido-rocha.

The largest Au deposits in the St Ives Goldfield (Yilgarn Craton, Western Australia) may be located in a major Neoarchean volcano-sedimentary depo-centre

The largest Neoarchean gold deposits in the world-class St Ives Goldfield, Western Australia, occur in an area known as the Argo-Junction region (e.g. Junction, Argo and Athena). Why this region is so well endowed with large deposits compared with other parts of the St Ives Goldfield is currently unclear, because gold deposits at St Ives are hosted by a variety of lithologic units and were formed during at least three different deformational events. This paper presents an investigation into the stratigraphic architecture and evolution of the Argo-Junction region to assess its implications for gold metallogenesis. The results show that the region's stratigraphy may be subdivided into five regionally correlatable packages: mafic lavas of the Paringa Basalt; contemporaneously resedimented feldspar-rich pyroclastic debris of the Early Black Flag Group; coarse polymictic volcanic debris of the Late Black Flag Group; thick piles of mafic lavas and sub-volcanic sills of the Athena Basalt and Condenser Dolerite; and the voluminous quartz-rich sedimentary successions of the Early Merougil Group. In the Argo-Junction region, these units have an interpreted maximum thickness of at least 7,130 m, and thus represent an unusually thick accumulation of the Neoarchean volcano-sedimentary successions. It is postulated that major basin-forming structures that were active during deposition and emplacement of the voluminous successions later acted as important conduits during mineralisation. Therefore, a correlation exists between the location of the largest gold deposits in the St Ives Goldfield and the thickest parts of the stratigraphy. Recognition of this association has important implications for camp-scale exploration.

Development of temperature-tolerant strains of Thiobacillus ferrooxidans to improve bioleaching kinetics

An isolate of Thiobacillus ferrooxidans derived from gold mine water samples was repeatedly subcultured at increasing temperatures (from 30 degrees to 42 degrees C) in 9K medium. The temperature-adapted strain was found to be more efficient in the bioleaching of pyrite mineral than the wild type. When temperature-tolerant strains were cultured repeatedly in 9K medium at 30 degrees C, the temperature tolerance was completely lost, These results indicate that the temperature tolerance was stress-dependent and not a permanent trait of the adapted strain, The potential utility of such temperature-tolerant strains of Thiobacillus ferrooxidans in sulphide mineral dissolution is demonstrated.

Biosorption of heavy metal ions from aqueous and cyanide solutions using fungal biomass

A waste fungal biomass containing killed cells of Aspergillus niger was efficiently used in the removal of toxic metal ions such as nickel, calcium, iron and chromium from aqueous solutions. The role of different parameters such as initial metal ion concentration, solution pH and biomass concentration on biosorption capacity was established. The maximum metal uptake was found to be dependent on solution pH and increased with biomass loading upto 10g/L. The adsorption densities for various metal ions could be arranged as Ca>Cr (III)>Ni>Fe>Cr (VI). The effect of the presence of various metal ions in binary, ternary and quaternary combinations on biosorption was also assessed. Ni uptake was significantly affected, while that of Cr (VI) the least, in the presence of other metal ions. Uptake of base metals from an industrial cyanide effluent was studied using different species of fungi such as Aspergillus niger, Aspergillus terreus and Penicillium funiculosum and yeast such as Saccharomyces cerevisiae which were isolated from a gold mine. Traces of gold present in the cyanide effluent could be efficiently recovered. Among the four base metal contaminants present in the cyanide effluent, zinc was found to be most efficiently biosorbed, followed by iron, copper and lead. The role of both living and dead biomass on biosorption was distinguished and probable mechanisms illustrated.

鄂霍次克海天然气水合物区与东海内陆架泥质区沉积物古菌多样性研究

为研究鄂霍次克海天然气水合物区沉积物古菌、甲烷厌氧氧化古菌和硫酸盐还原细菌的多样性分布，我们以PCR技术为基础构建mcrA、dsrAB和古菌16S rRNA 基因文库。对所获得的序列进行系统进化和统计学分析发现：鄂霍次克海古菌类群主要为Marine Benthic Group D (MBG-D)、Marine Benthic Group B (MBG-B)、Marine Crenarchaeotic Group I(MG- I)，另外少量古菌16S rRNA基因序列为Anaerobic Methanotrophs 2c（ANME-2c），主要分布在LV39-25H岩心的表层沉积物中。LV39-40H岩心表层的古菌群落结构与其他六个层位古菌群落结构相比有着显著的差异。mcrA基因序列主要为催化甲烷厌氧氧化的古菌ANME-2（c和d簇），在所研究的各个层位的沉积物中均广泛分布。少量的ANME-1（a簇）发现于LV39-40H岩心表层以下的沉积物中。产甲烷古菌数目不多，集中分布在LV39-25H岩心200cm和LV39-40H岩心180cm的沉积物中。dsrAB基因文库分析表明硫酸盐还原细菌种类丰富，表层沉积物中硫酸盐还原细菌多样性最高。在两个岩心所有层位的沉积物中都有一定数量的克隆属于DSS簇，它们可能与ANME共生催化甲烷的厌氧氧化作用。总之，所有数据表明在鄂霍次克海天然气水合物区存在着较活跃的甲烷厌氧氧化作用，揭示了参与甲烷厌氧氧化作用的微生物群落结构和多样性。 为研究东海内陆架闽浙沿岸泥质区不同深度沉积物中古菌群落垂向分布特征，通过古菌16S rRNA 基因文库共得到473个有效克隆50个OTUs (Operational Taxonomic Units)。16S rRNA基因序列系统进化和统计分析发现古菌分别归属于泉古生菌（Crenarchaeota）和广古生菌（Euryarchaeota），其中以Miscellaneous Crenarchaeotic Group（MCG）为主，仅含少量的MBG-B、South African Gold Mine Euryarchaeotic Group(SAGMEG)、 ANME-3、MG- I和MBG-D。该泥质区沉积物可能存在由ANME-3催化的甲烷厌氧氧化作用，同源序列分析表明其古菌群落分布与周边环境有较大联系。UniFrac与沉积物环境因子分析表明该泥质区古菌群落垂向分布与沉积物有机质含量和粒度变化密切相关。 通过对比发现，鄂霍次克海天然气水合物区甲烷厌氧氧化古菌主要为ANME-2和少量的ANME-1，而东海内陆架泥质区甲烷厌氧氧化古菌仅为极少量的ANME-3；鄂霍次克海天然气水合物区广古生菌和泉古生菌数量各占一半，主要为MBG-D、MBG-B、MG-I。东海内陆架泥质区沉积物古菌序列主要为泉古生菌（MCG）。海域类型的不同以及有机碳含量等环境因子的差异可能是这两个海域古菌群落结构差异的主要原因.

海底金属矿床充水条件及矿坑突水的断层效应研究

The Xinli mine area of Sanshandao mine is adjacent to the Bohai Sea and its main exploitable ore deposit occurs in the undersea rock mass. The mine is the biggest undersea gold mine of China after production. The mine area faces a latent danger of water bursting, even sudden seawater inrush. There is no mature experience in undersea mining in China so far. The vein ore deposit is located in the lower wall of a fault; its possible groundwater sources mainly include bittern, Quaternary pore water and modern seawater. To ensure the safety of undersea mining, to survey the flooding conditions of the ore deposit using proper measures and study the potential seawater inrush pattern are the key technical problems. With the Xinli mine area as a case study, the engineering geological conditions of the Xinli mine area are surveyed in situ, the regional structural pattern and rock mass framework characteristics are found out, the distribution of the structural planes are modeled by a Monte Carlo method and the connectivity coefficients of rock mass structural planes are calculated. The regional hydro-geological conditions are analyzed and the in-situ hydro-geological investigation and sampling are performed in detail, the hydrochemistry and isotopes testing and groundwater dynamic monitoring are conducted, the recharge, runoff, discharge conditions are specified and the sources of flooding are distinguished. Some indices are selected from the testing results to calculate the proportion of each source in some water discharge points and in the whole water discharge of the Xinli mine area. The temporal and spatial variations of each water source of the whole ore deposit flooding are analyzed. According to the special project conditions in the Xinli mine area, the permeability coefficient tensors of the rock mass in Xinli mine area are calculated based on a fracture geometry measurement method, in terms of the connectivity and a few hydraulic testing results, a modified synthetic permeability coefficient are calculated. The hydro-geological conceptual and mathematical model are established，the water yield of mine is predicted using Visual Modflow code. The spreading law of surrounding rock mass deformation and secondary stress are studied by numerical analysis; the intrinsic mechanism of the faults slip caused by the excavation of ore deposit is analyzed. The results show that the development of surrounding rock mass deformation and secondary stress of vein ore deposit in the lower wall of a fault, is different from that in a thick-big ore deposit. The secondary stress caused by the excavation of vein ore deposit in the lower wall of a fault, is mainly distributed in the upper wall of the fault, one surface subsidence center will occur. The influences of fault on the rock mass movement, secondary stress and hydro-geological structures are analyzed; the secondary stress is blocked by the fault and the tensile stress concentration occurs in the rock mass near the fault, the original water blocking structure is destructed and the permeable structure is reconstructed, the primary structural planes begin to expand and newborn fissures occur, so the permeability of the original permeable structure is greatly enhanced, so the water bursting will probably occur. Based on this knowledge, the possible water inrush pattern and position of the Xinli mine area are predicted. Some computer programs are developed using object-oriented design method under the development platform Visual Studio.Net. These programs include a Monte Carlo simulation procedure, a joint diagrammatizing procedure, a structural planes connectivity coefficient calculating procedure, a permeability tensor calculating procedure, a water chemical formula edit and water source fixture conditions calculating procedure. A new computer mapping algorithm of joint iso-density diagram is raised. Based on the powerful spatial data management and icon functions of Geographic Information System, the pit water discharge dynamic monitoring data management information systems are established with ArcView.

胶东蓬家夼式金矿床矿床成因模型与找矿模型研究

The dynamic environments of mineralization in Mesozoic Jiaodong gold mine concentrated area can be devided into two types, compressive environment which related to intracontinental collision and extensional environment which related to intracontinental volcanic rift. The altered rock type (Jiaojia type) and quartz vein type (Linglong type) which related to the former one, were discovered for several years, and became the main types of gold deposits in recent years. A new type gold deposit, syn-detachment altered tectonic breccia type gold deposit, such as Pengjiakuang gold deposit and Songjiagou gold deposit has been discovered on the northeastern margin of Jiaolai Basin. In this paper, the new type of gold deposit has been studied in detail. The study area is located at the northeastern boundaries of Jiaolai Basin, and between the Taocun-Jimo Fault and Wji-Haiyang Fault, in the eastern part of the Jiaodong Block. Pengjiakuang gold deposit and Songjiagou gold deposit occur in a arc-shape detachment fault zone between conglomerate of Lower Cretaceous Laiyang Formation and metamorphic complex of Lower Proterozoic Jingshan Group. Regional geological studies show that Kunyuanshan and Queshan granite intrusions and Qingshanian volcanism were formed in different period of lithospheric thinning of East China in Mesozoic. Granite intrusions were formed in compressive environment, while Qingshanian volcanism were formed in extensional environment. They are all related to the detachment of Sulu Orogenic Belt and the sinistral motion of Tanlu Fault. The Pengjiakuang detachment systems which were formed in the the sinistral motion of Tanlu Fault are the important ore-controlling and ore-containing structure. The Pengjiakuang type gold deposit, controlled by detachment structure, was formed before Yanshanian volcanic period concerning with mixture of meteoric water and magmatic water found in fluid inclusions of gold ores. The minerogenetic epoch has been proposed in 90～120Ma. the host rocks have been extensively subjected to pyritization, silicification, sericitization and carbonatization. Individual ore-body has maximum length of 800m, oblique extension of 500～700m and gold grade of 1～43 * 10~(-6). Native gold is disseminated in silicified, phyllic or carbonatized tectonic breccia. Sulfur, carbon and lead isotope studies on gold ores and wall rocks show that the sulfur come from the metamorphic complex of Lower Proterozoic Jingshan Group, carbon comes from the marble in Jingshan Group, while a part of lead comes from the mantle. The mineralizing fluid is rich in Na~+ and Cl~-, but relatively impoverished in K~+ and F~-. According to the date from hydrogen and oxygen isotopic compositions (δ~(18)OH_2O = 0.59%～4.03%, δDH_2O = -89.5%～97.9%), the conclusion can be reached that the mineralizing fluid of Pengjiakuang gold deposit was a kind of mixed hydrothermal solution which was mainly composed of meteoric water and magmatic water. A genetical model has been formulated. Some apparent anomaly features which show low in the central part and high in the both sides corresponding to the gold-bearing structure, were sum up after analying a vast amount of date by prospecting the orebodies using gamma-ray spectrometer, electrogeochemical parameter technique, controlled source audio magnetic telluric (CSAMT) and shallow surface thermometry in Pengjiakuang gold deposit. The location forecasting problem of buried orebodies has been solved according to these features, and the successful rate is very high in well-drilling. The structural geological-geophysical-geochemical prospecting model has been formulated on the base of the study of geological, geophysical and geochemical characteristics of Pengjiakuang type gold deposit, and the optimum combinational process of geophysical and geochemical prospecting techniques has been summed up. A comparative study shows that the Pengjiakuang type gold deposit, the syn-detachment altered tectonic breccia type gold deposit, is different from Jiaojia type gold deposits and Linglong type gold deposits, in Jiaodong Block. In general, if formed under an extensional tectonic condition and located at detachment fault zone along the margin of Mesozoic Jiaolai basin, and the gold mineralization has also close genetic relationship with alkaline magamtism. Being a new type of gold deposit in Jiaodong gold mine concentrated area, it could be potential to explore in the same regions which processed the same ore-forming geological conditions and mineralization informations.

地球化学新方法在隐状矿床找矿预测中的应用研究

With the progress of prospecting, the need for the discovery of blind ore deposits become more and more urgent. To study and find out the method and technology for the discovery of blind and buried ores is now a priority task. New geochemical methods are key technology to discover blind ores. Information of mobile components related to blind ores were extracted using this new methods. These methods were tested and applied based on element' s mobile components migrating and enriched in geophysical-geochemical process. Several kinds of partial extraction techniques have tested based on element' s occurrence in hypergenic zone. Middle-large scale geochemical methods for exploration in forest and swamp have been tested. A serious of methods were tested and applied effetely about evaluation of regional geochemical anomaly, 1:25000 bedrock or soil geochemical methods sampling based on the net in dendritic water system instead of the normal net. 1. Element related with ores can be mobiled to migrate upwards and be absorpted by surface soil. These abnomal components can be concentrated by natural or artificial methods. These trace metalic ions partially exist in dissovlvable ion forms of active state, and partially have been absorbed by Fe-Mn oxide, soil and organic matter in the soil so that a series of reaction such as complex reaction have take place. Employing various partial extraction techniques, metallic ions related with the phase of the blind ores can be extracted, such as the technique of organic complex extraction, Fe-Mn oxide extraction and the extraction technique of metallic ions of various absorption phases. 2.1:200000 regional geochemical evaluation anomaly methods: Advantageous ore-forming areas were selected firstly. Center, concentration, morphological feature, belt of anomaly were choosed then. Geological and geochemical anomalies were combined. And geological and geochemical background information were restrained. Xilekuduke area in Fuyun sheet , Zhaheba area in Qiakuerte sheet, the west-north part in Ertai sheet and Hongshanzui anomaly in Daqiao sheet were selected as target areas, in Alertai, in the north of Xinjiang. in Xilekuduke area, 1:25000 soil geochemical methods sampling based on the net in dendritic water system was carried out. Cu anomaly and copper mineralization were determined in the center area. Au , Cu anomalies and high polarization anomaly were determined in the south part. Prospecting by primary halo and organic complex extraction were used to prognosis blind ore in widely rang outcrop of bedrock. 1:25000 bedrock or soil geochemical methods sampling based on the net in dendritic water system were used in transported overburden outside of mining area. Shallow seismic method and primary halo found a new blind orebody in mining area. A mineralization site was fou and outside of Puziwan gold mine, in the north of Shanxi province. Developing middle-large scale geochemical exploration method is a key technique based 1:200000 regional geochemical exploration. Some conditions were tested as Sampling density , distribution sites of sample, grain size of sample and occurrence of element for exploration. 1:50000 exploration method was advanced to sample clast sediment supplement clast sediment in valley. 1:25000 bedrock or soil geochemical methods sampling based on the net in dendritic water system was applied to sample residual material in A or C horizon. 1:2000 primary or soil halo methods used to check anomalies and determine mineralization. Daliang gold mineralization in the northern Moerdaoga was found appling these methods. Thermomagnetic method was tested in miniqi copper-polymetallic ore. Process methods such as grain size of sample, heated temperature, magnetic separating technique were tested. A suite of Thermomagnetic geochemical method was formed. This method was applied in Xiangshan Cu~Ni deposit which is cover by clast or Gobi in the eastern Xinjiang. Element's content and contrast of anomaly with Thermomagnetic geochemical method were higher than soil anomaly. Susceptibility after samples were heated could be as a assessment conference for anomaly. In some sectors thermo-magnetic Cu, Ni, Ti anomalious were found outside deposits area. There were strong anomal ies response up ore tested by several kind of partial extraction methods include Thermomagnetic, enzyme leach and other partial extractions in Kalatongke Cu-Ni deposit in hungriness area in the northern of Xinjiang. Element's anomalies of meobile were mainly in Fe-Mn oxide and salt. A Copper mineralization site in Xilekuduke anomaly area had been determined. A blind ore was foung by shallow seismic and geochemical method and a mineralization site was found outside this mining area in Puziwan gold deposit in shanxi province. A Gold mineralization site was found by 1:50000 geochemical exploration in Daliang, Inner Mongolia.

Produção, qualidade e estado nutricional de meloeiro cultivado em Paraipaba-CE utilizando condicionador de solo sob diferentes lâminas de água.

Avaliação do efeito de um polímero hidrorretentor de umidade em diferentes lâminas de irrigação por gotejamento, na cultura do meloeiro híbrido amarelo Gold Mine.