Enhancing the high temperature plasticity of a Cu-containing austenitic stainless steel through grain boundary strengthening

The addition of 3 wt% Cu to heat-resistant SUS 304H austenitic steel enhances its high temperature mechanical properties. To further improve the properties, particularly the creep resistance and ductility at high temperatures, a post-solutionizing heat-treatment method that involves an intermediated annealing either at 700 or 800 degrees C after solutionizing for durations up to 180 min was employed. The purpose this heat-treatment is to precipitate planar Cr23C6 at the grain boundaries, which results in the boundaries getting serrated. Detailed microstructural analyses of these `grain boundary engineered' alloys was conducted and their mechanical performance, both at room temperature and at 750 degrees C, was evaluated. While the grain size and texture are unaffected due to the high temperature hold, the volume fraction of Sigma 3 twin boundaries was found to increase significantly. While the strength enhancement was only marginal, the ductility was found to increase significantly, especially at high temperature. A marked increase in the creep resistance was also noted, which is attributed to the reduction of the grain boundary sliding by the grain boundary serrations and the suppression of grain boundary cavitation through the optimization of the volume fraction and spacing of the Cr23C6 precipitates. The special heat-treatment performed with holding time of 3 h at 700 degrees C resulted in the optimum combination of strength, ductility and creep resistance at high temperature. (C) 2014 Elsevier B.V. All rights reserved.

Correlation of microstructure and creep behaviour of MRI230D Mg alloy developed by two different casting technologies

The relationship between the as-cast microstructure and creep behaviour of the heat-resistant MRI230D Mg alloy produced by two different casting technologies is investigated. The alloy in both ingot-casting (IC) and high pressure die-casting (HPDC) conditions consists of alpha-Mg, 06 ((Mg,AI)(2)Ca), Al-Mn and Sn-Mg-Ca rich phases. However, the HPDC alloy resulted in relatively finer grain size and higher volume fraction of finer, denser network of eutectic C36 phase in the as-cast microstructure as compared to that of the IC alloy. The superior creep resistance exhibited by the HPDC alloy at all the stress levels and temperatures employed in the present investigation was attributed to the more effective dispersion strengthening effect caused by the presence of finer and denser network of the C36 phase. The increased amount of the eutectic C36 phase was the only change observed in the microstructures of both alloys following creep tests. (C) 2015 Elsevier B.V. All rights reserved.

耐热Mg-Gd基合金的研究和应用

本研究从二元Mg-Gd体系出发，研究了添加不同稀土元素对Mg-Gd基合金的组织、时效行为和力学性能的影响。优化出多种力学性能优异、加工性能良好和耐热性突出的新型Mg-Gd-RE-Zn-Zr系合金。在探讨Mg-Gd基合金强化机理的同时，提出了强化模型，并进行了定量分析。 在Mg-Gd二元体系中，通过对不同Gd含量的合金组织，时效行为和力学性能的研究，发现Gd不仅可以细化晶粒，还可以细化枝晶。合金中Gd的含量大于8 wt.%开始表现出时效硬化现象，Gd含量超过12wt.％时效硬化效果显著。在二元体系研究结果的基础上，选用Mg-8Gd基合金，研究了不同轻稀土元素LRE(La, Ce和Nd)和重稀土元素HRE (Y, Dy, Ho 和Er)对合金组织和性能的影响。结果表明，轻稀土中Nd的作用效果最好，其次为Ce和La。重稀土中Y和Dy的作用效果较好，其次为Ho和Er。将轻、重稀土综合考虑，在Mg-8Gd-3RE(Nd+Y)-Zr合金中，变化Nd和Y的添加量，发现Nd和Y的添加量分别为1 和2或2和1时，能够明显改善合金的综合力学性能。 研究了Mg-8Gd-2Y-1Nd-0.3Zn和Mg-8Gd-1Dy-0.3Zn压铸合金的组织和性能。研究表明，两种合金的铸造性能好，而且具有优异的抗拉性能和蠕变性能，可以满足在250℃~275℃环境下使用。进一步研究了挤压变形Mg-8Gd-2Y-1Nd-0.3Zn合金。合金成形性能好，抗拉强度和伸长率明显提高，而且改善了合金的高温抗蠕变性能，比压铸合金提高了近一个数量级。 发明了一种新型的分步固溶处理方法——振荡热处理方法，这种方法比传统的T6热处理方法更加有效，振荡热处理的主要作用是改变了凝固过程中析出相的尺寸和分布。 研究了Mg-Gd基合金凝固过程中的相析出和相转变。在合金的凝固过程中，容易生成块状的化学组成为Mg5RE（fcc结构）的共晶相；加入Zn后，凝固中容易出现片状的Mg3RE（14H型）沉淀；时效强化的主要原因是在过饱和固溶体时效过程中析出针状的50 nm~100 nm的Mg15RE3相，它与基体具有半共格的位相关系，能够有效阻止位错滑移。但随着时效时间的延长，针状析出相长大，共格关系被破坏，导致强化作用降低。而对于压铸和挤压变形合金，合金析出相的种类不变，主要的不同是挤压变形合金析出化合物的分布更加均匀，尺寸更小。 开发了高强度耐热Mg-12Gd-4Y-2Nd-0.4Zn-0.6Zr合金，这种合金经过热处理后，力学性能优良，热稳定性突出。在300 ℃的抗拉强度约为300 MPa，400 ℃的抗拉强度在100 MPa以上。本合金流动性能良好，适合于砂型铸造，在具有高温、高强度要求的镁合金制品方面极具潜力。 从金属材料强化原理出发，建立了Mg-Gd基合金的强化模型，并进行了定量分析。结果表明，析出强化是Mg-Gd基合金的主要强化方式，但实际试验值和理论值略有偏差，分析认为主要是由于β'相体积分数的变化区间较宽，且合金制备过程中不可避免地产生一些微观缺陷所致。 采用新型合金制备出了一些工业用品部件，探索了该类合金在机械、汽车和高技术等工业领域中的潜在应用

含钇的耐热稀土镁合金的结构和性能研究

耐热、高强和抗高温蠕变的稀土镁合金是镁合金研究与开发的重要研究课题之一。本论文主要集中于对Y和其它稀土元素复合加入镁后的镁合金结构和性能的研究。探讨了Y与其它重稀土元素如Gd、Ho复合加入镁后的镁合金的时效硬化行为和结构性能，也研究了Y与混合轻稀土金属如富铈、富镧复合加入镁后对镁合金性能的影响。还对新型Mg-Y压铸镁合金的开发为目标，探讨了这一新型合金开发的可行性。具体结果如下： 1. 研究了Y加入到Mg-10Gd-0.4Zr合金中对合金的时效硬化和性能的影响规律和Mg-10Gd-6Y-0.4Zr合金在225℃和250℃时效210h内的沉淀析出相的转变以及合金的时效硬化行为。随着Y含量的增加，合金的时效硬化反应显著增强，合金的高温拉伸强度随Y含量的增加而线性增强，其原因是合金中的β'相有好的热稳定性。 2. 研究了Y和Ho元素复合加入镁后镁合金的时效硬化反应和组织性能。研究发现，在250℃时效时，当Y和Ho元素复合加入镁后，合金固溶体的时效分解速度加快，促进了合金的时效硬化，并且，随着Y含量的增加，合金的时效硬化反应增强，力学性能也相应提高。β-Mg24Y(Ho)5和（或）β'相对合金的时效硬化起了主要的作用，而且，位错密度增加也是合金性能提高的重要原因。 3. 探讨了Y和混合轻稀土富铈（和富镧）复合加入镁后对镁合金的性能影响。富铈和富镧在镁中低的固溶度导致单独加入镁后的时效硬化反应很弱，当Y和混合轻稀土富铈（和富镧）复合加入后，合金的时效硬化反应明显增强，并随着Y含量的增加，时效硬化的反应也相应增强。富铈和富镧对Mg-Y合金固溶体的时效分解有明显的促进作用。除了基体中的沉淀强化外，仍然停留在晶界上的Mg12RE稀土相对合金的晶界也有明显的强化作用。 4. 研究开发了具有良好的力学性能和高温抗蠕变性能、低含量Y、Gd的稀土镁合金，实验结果表明该合金是一种有良好应用前景的压铸镁合金。

Kinetic analysis of interaction between lipopolysaccharide and biomolecules

Lipopolysaccharide ( LPS) is a major component of the outer membrane of all gram-negative bacteria. It is a heat-resistant toxin which can cause toxic shock in animals. LPS interacts with some biomolecules and triggers its toxic reaction. In this study, the interaction between LPS from Salmonella Minnesota and some biomolecules using syrface okasnib resibabce ( SPR) biosensor. biomolecules were imobilized on CM5 sensor-chip suing amion coupling method and LPS was injected over the immobilized surfaces.

Syntheses and properties of polyimides derived from diamines containing 2,5-disubstituted pyridine group

A Series of novel homo- and copolyimides containing pyridine units were prepared from the heteroaromatic diamines, 2,5-bis (4-aminophenyl) pyridine and 2-(4aminophenyl)-5-aminopyridine, with pyromelltic dianhydride (PMDA), and 3,3',4,4'-biphenyl tertracarboxylic dianhydride (BPDA) via a conventional two-step thermal imidizaton method. The poly(amic acid) precursors have inherent viscosities of 1.60-9.64 dL/g (c = 0.5 g/dL in DMAC, 30 degrees C) and all of them can be cast and thermally converted into flexible and tough polyimide films. All of the polyimides show excellent thermal stability and mechanical properties. The polyimides have 10% weight loss temperature in the range of 548-598 degrees C in air. The glass transition temperatures of the PMDA-based samples are in the range of 395-438 degrees C, while the BPDA-based polyimides show two glass transition temperatures (T(g)1 and T(g)2), ranging from 268 to 353 degrees C and from 395 to 418 degrees C, respectively. The flexible films possess tensile modulus in the range of 3.42-6.39 GPa, strength in the range of 112-363 MPa and an elongation at break in the range of 1.2-69%. The strong reflection peaks in the wide-angle X-ray diffraction patterns indicate that the polyimides have a high packing density and crystallinity.

Syntheses and properties of novel polyimides derived from 2-(4-aminophenyl)-5-aminopyrimidine

2-(4-Aminophenyl)-5-aminopyrimidine (4) is synthesized via a condensation reaction of vinamidium salts and amidine chloride salts, followed by hydrazine palladium catalyzed reduction. A series of novel homo- and copolyimides containing pyrimidine unit are prepared from the diamine and 1,4-phenylenediamine (PDA) with pyromellitic dianhydride (PMDA) or 3,3',4,4'-biphenyl tertracarboxylic dianhydride (BPDA) via a conventional two-step thermal imidization method. The poly(amic acid) precursors had inherent viscosities of 0.97-4.38 dL/g (c = 0.5 g/dL, in DMAc, 30 degrees C) and all of them could be cast and thermally converted into flexible and tough polyimide films. All of the polyimides showed excellent thermal stability and mechanical properties. The glass transition temperatures of the resulting polyimides are in the range of 307-434 degrees C and the 10% weight loss temperature is in the range of 556-609 degrees C under air. The polyimide films possess strength at break in the range of 185-271 MPa, elongations at break in the range of 6.8-51%, and tensile modulus in the range of 3.5-6.46 GPa. The polymer films are insoluble in common organic solvents, exhibiting high chemical resistance.

STRUCTURE AND PROPERTIES OF SEQUENTIALLY POLYMERIZED PROPYLENE-B-[ETHYLENE-CO-PROPYLENE]-B-PROPYLENE COPOLYMERS

The structure and properties of presumed block copolymers of polypropylene (PP) with ethylene-propylene random copolymers (EPR), i.e., PP-EPR and PP-EPR-PP, have been investigated by viscometry, transmission electron microscopy, dynamic mechanical analysis, differential scanning calorimetry, gel permeation chromatography, wide-angle x-ray diffraction, and other techniques testing various mechanical properties. PP-EPR and PP-EPR-PP were synthesized using delta-TiCl3-Et2AlCl as a catalyst system. The results indicate that the intrinsic viscosity of these polymers increases with each block-building step, whereas the intrinsic viscosity of those prepared by chain transfer reaction (strong chain-transfer reagent hydrogen was introduced between block-building steps during polymerization) hardly changes with the reaction time. Compared with PP / EPR blends, PP-EPR-PP block copolymers have lower PP and polyethylene crystallinity, and lower melting and crystallization temperatures of crystalline EPR. Two relaxation peaks of PP and EPR appear in the dynamic spectra of blends. They merge into a very broad relaxation peak with block sequence products of the same composition, indicating good compatibility between PP and EPR in the presence of block copolymers. Varying the PP and EPR content affects the crystallinity, density, and morphological structure of the products, which in turn affects the tensile strength and elongation at break. Because of their superior mechanical properties, sequential polymerization products containing PP-EPR and PP-EPR-PP block copolymers may have potential as compatibilizing agents for isotactic polypropylene and polyethylene blends or as potential heat-resistant thermoplastic elastomers.

Relationship between Laves phase and the impact brittleness of P92 steel reevaluated

Laves phase has been widely accepted to cause the impact brittleness of 9–12Cr martensitic heat-resistant steels after long time aging at elevated temperatures. However, in the present research, the impact toughness of the already brittle P92 steel aged at 600 °C for 2035 h could be restored to the original level by reheating at 700 °C for 1 h, with Laves phase barely changed. This interesting result strongly indicated that the presence of Laves phase might not be the real reason for the impact brittleness.

On the anharmonic, multi-phonon, Debye-Waller contributions to the phonon-limited resistivity of metals : applications to Na and K

The anharmonic, multi-phonon (MP), and Oebye-Waller factor (OW) contributions to the phonon limited resistivity (;0) of metals derived by Shukla and Muller (1979) by the doubletime temperature dependent Green function method have been numerically evaluated for Na and K in the high temperature limit. The anharmonic contributions arise from the cubic and quartic shift of phonons (CS, QS), and phonon width (W) and the interference term (1). The QS, MP and OW contributions to I' are also derived by the matrix element method and the results are in agreement with those of Shukla and Muller (1979). In the high temperature limit, the contributions to;O from each of the above mentioned terms are of the type BT2 For numerical calculations suitable expressions are derived for the anharmonic contributions to ~ in terms of the third and fourth rank tensors obtained by the Ewald procedure. The numerical calculation of the contributions to;O from the OW, MP term and the QS have been done exactly and from the CS, Wand I terms only approximately in the partial and total Einstein approximations (PEA, TEA), using a first principle approach (Shukla and Taylor (1976)). The results obtained indicate that there is a strong pairwise cancellation between the: OW and MP terms, the QS and CS and the Wand I terms. The sum total of these contributions to;O for Na and K amounts to 4 to 11% and 2 to 7%, respectively, in the PEA while in the TEA they amount to 3 to 7% and 1 to 4%, respectively, in the temperature range.

Modèles cellulaires pour étudier les interactions entre Actinobacillus pleuropneumoniae et le virus du syndrome reproducteur et respiratoire porcin

Durant une infection pulmonaire, les porcs sont souvent infectés par plus d’un microorganisme. Actinobacillus pleuropneumoniae et le virus du syndrome reproducteur et respiratoire porcin (VSRRP) sont des pathogènes qui peuvent infecter de manière simultanée les porcs. L’objectif du présent projet est d’étudier l’interaction entre ces pathogènes. Les deux lignées cellulaires permissives au VSRRP utilisées sont les cellules « St-Jude porcine lung » (SJPL) et MARC-145. Les cellules ont été pré-infectées avec le VSRRP, puis infectées avec A. pleuropneumoniae. Un dosage de la lactate déshydrogénase a montré qu’une co-infection VSRRP-A. pleuropneumoniae comparée à une infection simple augmente significativement la cytotoxicité. Dans les mêmes conditions expérimentales, une pré-infection virale ne semble pas affecter l’adhérence d’A. pleuropneumoniae aux cellules. À l’aide de tests ELISA, il a été possible de démontrer la production d’IL-8 et d’INF-γ lorsqu’il y a infection des cellules. Pour ce qui est du TNF-α, d’IL-6 et d’IL-10, ces cytokines ne sont pas détectées en présence des pathogènes étudiés. Des expériences de pré-infection bactérienne suivie d’infection virale ont également été réalisées. Il a été démontré que la pré-infection avec A. pleuropneumoniae diminuait la réplication du VSRRP chez la lignée cellulaire SJPL, mais cela n’est pas observé avec la lignée cellulaire MARC-145. Les résultats préliminaires ont démontré que cette diminution de la réplication serait causée par une molécule de faible poids moléculaire sécrétée dans le surnageant bactérien et celle-ci serait résistante à la chaleur. Les lignées cellulaires SJPL et MARC-145 représentent de bons modèles pour l’étude des infections mixtes des voies respiratoires du porc.

Detection and quantification of staphylococcus aureus enterotoxin B in food product using isotopic dilution techniques and mass spectrometry

L’entérotoxine B staphylococcique (SEB) est une toxine entérique hautement résistante à la chaleur et est responsable de plus de 50 % des cas d’intoxication d’origine alimentaire par une entérotoxine. L’objectif principal de ce projet de maîtrise est de développer et valider une méthode basée sur des nouvelles stratégies analytiques permettant la détection et la quantification de SEB dans les matrices alimentaires. Une carte de peptides tryptiques a été produite et 3 peptides tryptiques spécifiques ont été sélectionnés pour servir de peptides témoins à partir des 9 fragments protéolytiques identifiés (couverture de 35 % de la séquence). L’anhydride acétique et la forme deutérée furent utilisés afin de synthétiser des peptides standards marqués avec un isotope léger et lourd. La combinaison de mélanges des deux isotopes à des concentrations molaires différentes fut utilisée afin d’établir la linéarité et les résultats ont démontré que les mesures faites par dilution isotopique combinée au CL-SM/SM respectaient les critères généralement reconnus d’épreuves biologiques avec des valeurs de pente près de 1, des valeurs de R2 supérieure à 0,98 et des coefficients de variation (CV%) inférieurs à 8 %. La précision et l’exactitude de la méthode ont été évaluées à l’aide d’échantillons d’homogénat de viande de poulet dans lesquels SEB a été introduite. SEB a été enrichie à 0,2, 1 et 2 pmol/g. Les résultats analytiques révèlent que la méthode procure une plage d’exactitude de 84,9 à 91,1 %. Dans l’ensemble, les résultats présentés dans ce mémoire démontrent que les méthodes protéomiques peuvent être utilisées efficacement pour détecter et quantifier SEB dans les matrices alimentaires. Mots clés : spectrométrie de masse; marquage isotopique; protéomique quantitative; entérotoxines

L’entérotoxine STb d’Escherichia coli déloge la claudine-1 des jonctions serrées

Escherichia coli produit diverses entérotoxines thermolabiles et thermostables. STb est une toxine de faible poids moléculaire résistant à la chaleur chargée de la diarrhée chez les animaux de la ferme. Une étude antérieure a montré que les cellules ayant internalisé la toxine STb provoquent un dysfonctionnement de la barrière épithéliale par des changements dans les protéines des jonctions serrées (TJ). Ces modifications contribuent probablement à la diarrhée observée. Pour mieux comprendre le mécanisme de l'augmentation de la perméabilité intestinale, nous avons traité les cellules du côlon humain (T84) avec la toxine purifiée STb une fois que les cellules ont été récoltées et les protéines extraites. Après l'utilisation d'une solution contenant 1% de Nonidet P-40 (un détergent non dénaturant, non ionique), nous avons étudié la distribution de la claudine -1, une protéine majeure des TJs, responsable de l'imperméabilité de l'épithélium, entre la membrane (NP40-insoluble) et le cytoplasme (NP40-soluble). En utilisant l’immunoblot et la microscopie confocale, nous avons observé que le traitement des monocouches de cellules T84 avec STb induit la redistribution de la claudine-1. Après 24h, les cellules cultivées en milieu faible en Ca+ (5 uM) et traitées par STb, ont montré qu’environ 40 % de plus de la claudine-1 se sont délogées dans le cytoplasme par comparaison au contrôle. En passant d’un milieu faible à un milieu contenant des quantités physiologiques de Ca++ (1,8 mM) nous avons observé une augmentation du taux de claudine- 1 délogé, comme la délocalisation comparable et ce, après 6h. Un milieu supplémenté avec la même concentration de Mg++ ou Zn++ n'a pas affecté le taux de délogement comparé au milieu contenant une faible teneur en Ca++. En utilisant des anticorps anti-phosphosérine et anti-phosphothréonine, nous avons observé que la perte des claudines-1 de la membrane a été accompagnée par une déphosphorylation de cette protéine des TJs. Dans l'ensemble, nos résultats ont montré une importante redistribution de la claudine-1 dans les cellules traitées par la toxine STb. La perte de la claudine-1 phosphorylée de la membrane est susceptible d'être impliquée dans la perméabilité accrue observée. Les mécanismes par lesquels ces changements sont provoqués restent à élucider.

Actinobacillus pleuropneumoniae Possesses an Antiviral Activity against Porcine Reproductive and Respiratory Syndrome Virus

Pigs are often colonized by more than one bacterial and/or viral species during respiratory tract infections. This phenomenon is known as the porcine respiratory disease complex (PRDC). Actinobacillus pleuropneumoniae (App) and porcine reproductive and respiratory syndrome virus (PRRSV) are pathogens that are frequently involved in PRDC. The main objective of this project was to study the in vitro interactions between these two pathogens and the host cells in the context of mixed infections. To fulfill this objective, PRRSV permissive cell lines such as MARC-145, SJPL, and porcine alveolar macrophages (PAM) were used. A pre-infection with PRRSV was performed at 0.5 multiplicity of infection (MOI) followed by an infection with App at 10 MOI. Bacterial adherence and cell death were compared. Results showed that PRRSV preinfection did not affect bacterial adherence to the cells. PRRSV and App co-infection produced an additive cytotoxicity effect. Interestingly, a pre-infection of SJPL and PAM cells with App blocked completely PRRSV infection. Incubation of SJPL and PAM cells with an App cell-free culture supernatant is also sufficient to significantly block PRRSV infection. This antiviral activity is not due to LPS but rather by small molecular weight, heat-resistant App metabolites (,1 kDa). The antiviral activity was also observed in SJPL cells infected with swine influenza virus but to a much lower extent compared to PRRSV. More importantly, the PRRSV antiviral activity of App was also seen with PAM, the cells targeted by the virus in vivo during infection in pigs. The antiviral activity might be due, at least in part, to the production of interferon c. The use of in vitro experimental models to study viral and bacterial co-infections will lead to a better understanding of the interactions between pathogens and their host cells, and could allow the development of novel prophylactic and therapeutic tools.

Photothermal and photoacoustic investigations on certain polymers and semi conducting materials

Material synthesizing and characterization has been one of the major areas of scientific research for the past few decades. Various techniques have been suggested for the preparation and characterization of thin films and bulk samples according to the industrial and scientific applications. Material characterization implies the determination of the electrical, magnetic, optical or thermal properties of the material under study. Though it is possible to study all these properties of a material, we concentrate on the thermal and optical properties of certain polymers. The thermal properties are detennined using photothermal beam deflection technique and the optical properties are obtained from various spectroscopic analyses. In addition, thermal properties of a class of semiconducting compounds, copper delafossites, arc determined by photoacoustic technique.Photothermal technique is one of the most powerful tools for non-destructive characterization of materials. This forms a broad class of technique, which includes laser calorimetry, pyroelectric technique, photoacollstics, photothermal radiometric technique, photothermal beam deflection technique etc. However, the choice of a suitable technique depends upon the nature of sample and its environment, purpose of measurement, nature of light source used etc. The polynler samples under the present investigation are thermally thin and optically transparent at the excitation (pump beam) wavelength. Photothermal beam deflection technique is advantageous in that it can be used for the detennination of thermal diffusivity of samples irrespective of them being thermally thick or thennally thin and optically opaque or optically transparent. Hence of all the abovementioned techniques, photothemlal beam deflection technique is employed for the successful determination of thermal diffusivity of these polymer samples. However, the semi conducting samples studied are themlally thick and optically opaque and therefore, a much simpler photoacoustic technique is used for the thermal characterization.The production of polymer thin film samples has gained considerable attention for the past few years. Different techniques like plasma polymerization, electron bombardment, ultra violet irradiation and thermal evaporation can be used for the preparation of polymer thin films from their respective monomers. Among these, plasma polymerization or glow discharge polymerization has been widely lIsed for polymer thin fi Im preparation. At the earlier stages of the discovery, the plasma polymerization technique was not treated as a standard method for preparation of polymers. This method gained importance only when they were used to make special coatings on metals and began to be recognized as a technique for synthesizing polymers. Thc well-recognized concept of conventional polymerization is based on molecular processcs by which thc size of the molecule increases and rearrangemcnt of atoms within a molecule seldom occurs. However, polymer formation in plasma is recognized as an atomic process in contrast to the above molecular process. These films are pinhole free, highly branched and cross linked, heat resistant, exceptionally dielectric etc. The optical properties like the direct and indirect bandgaps, refractive indices etc of certain plasma polymerized thin films prepared are determined from the UV -VIS-NIR absorption and transmission spectra. The possible linkage in the formation of the polymers is suggested by comparing the FTIR spectra of the monomer and the polymer. The thermal diffusivity has been measured using the photothermal beam deflection technique as stated earlier. This technique measures the refractive index gradient established in the sample surface and in the adjacent coupling medium, by passing another optical beam (probe beam) through this region and hence the name probe beam deflection. The deflection is detected using a position sensitive detector and its output is fed to a lock-in-amplifIer from which the amplitude and phase of the deflection can be directly obtained. The amplitude and phase of the deflection signal is suitably analyzed for determining the thermal diffusivity.Another class of compounds under the present investigation is copper delafossites. These samples in the form of pellets are thermally thick and optically opaque. Thermal diffusivity of such semiconductors is investigated using the photoacoustic technique, which measures the pressure change using an elcctret microphone. The output of the microphone is fed to a lock-in-amplificr to obtain the amplitude and phase from which the thermal properties are obtained. The variation in thermal diffusivity with composition is studied.