Effect of microwave on formation/decomposition of natural gas hydrate

Natural gas hydrate (NGH) reservoirs have been considered as a substantial future clean energy resource and how to recover gas from these reservoirs feasibly and economically is very important. Microwave heating will be taken as a promising method for gas production from gas hydrates for its advantages of fast heat transfer and flexible application. In this work, we investigate the formation/decomposition behavior of natural gas hydrate with different power of microwave (2450MHZ), preliminarily analyze the impact of microwave on phase equilibrium of gas hydrate,and make calculation based on van der Waals-Platteeuw model. It is found that microwave of a certain amount of power can reduce the induction time and sub-cooling degree of NGH formation, e.g., 20W microwave power can lead to a decrease of about 3A degrees C in sub-cooling degree and the shortening of induction time from 4.5 hours to 1.3 hours. Microwave can make rapid NGH decomposition, and water from NGH decomposition accelerates the decomposition of NGH with the decomposition of NGH. Under the same pressure, microwave can increase NGH phase equilibrium temperature. Different dielectric properties of each composition of NGH may cause a distinct difference in temperature in the process of NGH decomposition. Therefore, NGH decomposition by microwave can be affected by many factors.

Control mechanisms for gas hydrate production by depressurization in different scale hydrate reservoirs

The methane hydrate was formed in a pressure vessel 38 mm in id and 500 mm in length. Experimental works on gas production from the hydrate-bearing core by depressurization to 0.1, 0.93, and 1.93 MPa have been carried out. The hydrate reservoir simulator TOUGH-Fx/Hydrate was used to simulate the experimental gas production behavior, and the intrinsic hydration dissociation constant (K-0) fitted for the experimental data was on the order of 104 mol m(-2) Pa-1 s(-1), which was one order lower than that of the bulk hydrate dissociation. The sensitivity analyses based on the simulator have been carried out, and the results suggested that the hydrate dissociation kinetics had a great effect on the gas production behavior for the laboratory-scale hydrate-bearing core. However for a field-scale hydrate reservoir, the flow ability dominated the gas production behavior and the effect of hydrate dissociation kinetics on the gas production behavior could be neglected.

Thermally induced evolution of phase transformations in gas hydrate sediment

Thermally induced evolution of phase transformations is a basic physical-chemical process in the dissociation of gas hydrate in sediment (GHS). Heat transfer leads to the weakening of the bed soil and the simultaneous establishment of a time varying stress field accompanied by seepage of fluids and deformation of the soil. As a consequence, ground failure could occur causing engineering damage or/and environmental disaster. This paper presents a simplified analysis of the thermal process by assuming that thermal conduction can be decoupled from the flow and deformation process. It is further assumed that phase transformations take place instantaneously. Analytical and numerical results are given for several examples of simplified geometry. Experiments using Tetra-hydro-furan hydrate sediments were carried out in our laboratory to check the theory. By comparison, the theoretical, numerical and experimental results on the evolution of dissociation fronts and temperature in the sediment are found to be in good agreement.

Geophysical signatures associated with fluid flow and gas hydrate occurrence in a tectonically quiescent sequence, Qiongdongnan Basin, South China Sea

Interpretation of high-resolution two-dimensional (2D) and three-dimensional (3D) seismic data collected in the Qiongdongnan Basin, South China Sea reveals the presence of polygonal faults, pockmarks, gas chimneys and slope failure in strata of Pliocene and younger age. The gas chimneys are characterized by low-amplitude reflections, acoustic turbidity and low P-wave velocity indicating fluid expulsion pathways. Coherence time slices show that the polygonal faults are restricted to sediments with moderate-amplitude, continuous reflections. Gas hydrates are identified in seismic data by the presence of bottom simulating reflectors (BSRs), which have high amplitude, reverse polarity and are subparallel to seafloor. Mud diapirism and mounded structures have variable geometry and a great diversity regarding the origin of the fluid and the parent beds. The gas chimneys, mud diapirism, polygonal faults and a seismic facies-change facilitate the upward migration of thermogenic fluids from underlying sediments. Fluids can be temporarily trapped below the gas hydrate stability zone, but fluid advection may cause gas hydrate dissociation and affect the thickness of gas hydrate zone. The fluid accumulation leads to the generation of excess pore fluids that release along faults, forming pockmarks and mud volcanoes on the seafloor. These features are indicators of fluid flow in a tectonically-quiescent sequence, Qiongdongnan Basin. Geofluids (2010) 10, 351-368.

Gas hydrate associated with mud diapirs in southern Okinawa Trough

Many mud diapirs have been recognized in southern Okinawa Trough by a multi-channel seismic surveying on R/V KEXUE I in 2001. Gas hydrates have been identified, by the seismic reflection characteristics, the velocity analysis and the impedance inversion. Geothermal heat flow around the central of the mud diapir has been determined theoretically by the Bottom Simulating Reflectors (BSRs). Comparing the BSR derived and the measured heat flow values, we infer that the BSR immediately at the top of the mud diapirs indicate the base of the saturated gas hydrate formation zone (BSGHFZ), but not, as we ordinarily know, the base of the gas hydrate stability zone (BGHSZ), which could be explained by the abnormal regional background heat flow and free gas flux associated with mud diapirs. As a result, it helps us to better understand the generation mechanism of the gas hydrates associated with mud diapirs and to predict the gas hydrate potential in the southern Okinawa Trough. (C) 2008 Elsevier Ltd. All rights reserved.

Gas hydrate occurrence on the continental slope of the northern South China Sea

High-resolution multi-channel seismic data and geological samples were collected during two research cruises of the R/V FENDOU 4 in 1999 and 2000. Studies on these data and samples together with results from sites 1143-1145 and 1148 of ODP Leg 184 suggest that the geological structure on the continental slope of the northern South China Sea is favorable for the formation of gas hydrates. Bottom simulating reflectors (BSRs) and geochemical anomalies which indicate the existence of gas hydrates have been recognized in sediments of the Xisha Trough, the Dongsha Rise and the accretionary wedge of the Manila subduction zone. These gas hydrates are generated by two different mechanisms depending on the tectonic regime and the seismic and geochemical characteristics. The first applies to the passive continental margin of the nor-them South China Sea on the Dongsha Rise and in the Xisha Trough. The gas hydrates are associated with diapiric structures, active faults, slumps and gravity flows as well as high Late Cenozoic sedimentation rates. Their seismic expression includes BSRs, seismic blanking zones and velocity anomalies. The second mechanism is operative on the active continental margin along the Manila subduction zone, especially in the accretionary wedge. Here, gas hydrate occurrence is marked by widespread BSRs and acoustic 'pull-down' possibly related to the existence of free gas in the sediments beneath the BSR. The thickness of the seismic blanking zones averages 250 m, suggesting that the stable gas hydrate zone has about the same thickness. (c) 2005 Elsevier Ltd. All rights reserved.

The stability zone of gas hydrate in the slope of East China Sea and neighboring trough basin area

We analyze the distribution of temperature and heat flow of the sea floor sediment in the area of East China Sea slope and West basin area of the Okinawa Trough. Based on the Sonar Buoy and OBS data, 6 velocity layers are recognized, each of which has velocity of 1.8(1.8 similar to 2.2) km/s,2.2(2.0 similar to 2.5)km/s,2.8 (2.7 similar to 3.2)km/s,3.4 similar to 3.6km/s,4.2(4.1 similar to 4.7)km/s and 5.1km/s, respectively. The upper velocity layer of 1.8 similar to 2.2 km/s corresponds to the Quaternary sediment stratum. The layer with velocity 3.4 similar to 4.2km/s is the Pliocene sediment stratum. The area that is suitable for stable existence of gas hydrate by the temperature and pressure is 70,000km(2) about 1/10 the total area of East China Sea. The thickness of the stability zone ranges from 400m (Middle Part of Okinawa Trough) to 1100m (North and South Part of Okinawa Trough). The Quaternary and Pliocene layers are suitable for stable exitence of gas hydrate. According to the tectonic stability and heat flow, the north part and south part of the Okinawa Trough are the most perspective area for the gas hydrate explorations.

Characteristics of shallow gas hydrate in Okhotsk Sea

Multidisciplinary field investigations were carried out in Okhotsk Sea by R/V Akademik M.A. Lavrentyev (LV) of the Russian Academy of Sciences (RAS) in May 2006, supported by funding agencies from Korea, Russia, Japan and China. Geophysical data including echo-sounder, bottom profile, side-scan-sonar, and gravity core sample were obtained aimed to understand the characteristics and formation mechanism of shallow gas hydrates. Based on the geophysical data, we found that the methane flare detected by echo-sounder was the evidence of free gas in the sediment, while the dome structure detected by side-scan sonar and bottom profile was the root of gas venting. Gas hydrate retrieved from core on top of the dome structure which was interbedded as thin lamination or lenses with thickness varying from a few millimeters to 3 cm. Gas hydrate content in hydrate-bearing intervals visually amounted to 5%-30% of the sediment volume. This paper argued that gases in the sediment core were not all from gas hydrate decomposition during the gravity core lifting process, free gases must existed in the gas hydrate stability zone, and tectonic structure like dome structure in this paper was free gas central, gas hydrate formed only when gases over-saturated in this gas central, away from these structures, gas hydrate could not form due to low gas concentration.

Authigenic sulfide minerals and their sulfur isotopes in sediments of the northern continental slope of the South China Sea and their implications for methane flux and gas hydrate formation

This is a report of the study of the authigenic sulfide minerals and their sulfur isotopes in a sediment core (NH-1) collected on the northern continental slope of the South China Sea, where other geophysical and geochemical evidence seems to suggest gas hydrate formation in the sediments. The study has led to the findings: (1) the pyrite content in sediments was relatively high and its grain size relatively large compared with that in normal pelagic or hemipelagic sediments; (2) the shallowest depth of the acid volatile sulfide (AVS) content maximum was at 437.5 cm (> 2 mu mol/g), which was deeper than that of the authigenic pyrite content maximum (at 141.5-380.5 cm); (3) delta S-34 of authigenic pyrite was positive (maximum: +15 parts per thousand) at depth interval of 250-380 cm; (4) the positive delta S-34 coincided with pyrite enrichment. Compared with the results obtained from the Black Sea sediments by Jorgensen and coworkers, these observations indicated that at the NH-1 site, the depth of the sulfate-methane interface (SMI) would be or once was at about 437.5-547.5 cm and the relatively shallow SMI depth suggested high upward methane fluxes. This was in good agreement with the results obtained from pore water sulfate gradients and core head-space methane concentrations in sediment cores collected in the area. All available evidence suggested that methane gas hydrate formation may exist or may have existed in the underlying sediments.

Low-amplitude BSRs and gas hydrate concentration on the northern margin of the South China Sea

The passive northern continental margin of the South China Sea is rich in gas hydrates, as inferred from the occurrence of bottom-simulating reflectors (BSR) and from well logging data at Ocean Drilling Program (ODP) drill sites. Nonetheless, BSRs on new 2D multichannel seismic reflection data from the area around the Dongsha Islands (the Dongsha Rise) are not ubiquitous. They are confined to complex diapiric structures and active fault zones located between the Dongsha Rise and the surrounding depressions, implying that gas hydrate occurrence is likewise limited to these areas. Most of the BSRs have low amplitude and are therefore not clearly recognizable. Acoustic impedance provides information on rock properties and has been used to estimate gas hydrate concentration. Gas hydrate-bearing sediments have acoustic impedance that is higher than that of the surrounding sediments devoid of hydrates. Based on well logging data, the relationship between acoustic impedance and porosity can be obtained by a linear regression, and the degree of gas hydrate saturation can be determined using Archie's equation. By applying these methods to multichannel seismic data and well logging data from the northern South China Sea, the gas hydrate concentration is found to be 3-25% of the pore space at ODP Site 1148 depending on sub-surface depth, and is estimated to be less than values of 5% estimated along seismic profile 0101. Our results suggest that saturation of gas hydrate in the northern South China Sea is higher than that estimated from well resistivity log data in the gas hydrate stability zone, but that free gas is scarce beneath this zone. It is probably the scarcity of free gas that is responsible for the low amplitudes of the BSRs.

Estimation of gas hydrate saturation using constrained sparse spike inversion: Case study from the northern South China Sea

Bottom-simulating reflectors (BSRs) were observed beneath the seafloor in the northern continental margin of the South China Sea (SCS). Acoustic impedance profile was derived by Constrained Sparse Spike Inversion (CSSI) method to provide information on rock properties and to estimate gas hydrate or free gas saturations in the sediments where BSRs are present. In general, gas hydrate-bearing sediments have positive impedance anomalies and free gas-bearing sediments have negative impedance anomalies. Based on well log data and Archie's equation, gas hydrate saturation can be estimated. But in regions where well log data is not available, a quantitative estimate of gas hydrate or free gas saturation is inferred by fitting the theoretical acoustic impedance to sediment impedance obtained by CSSI. Our study suggests that gas hydrate saturation in the Taixinan Basin is about 10 - 20% of the pore space, with the highest value of 50%, and free gas saturation below BSR is about 2 - 3% of the pore space, that can rise to 8 - 10% at a topographic high. The free gas is non-continuous and has low content in the southeastern slope of the Dongsha Islands. Moreover, BSR in the northern continental margin of the SCS is related to the presence of free gas. BSR is strong where free gas occurs.

Factors affecting the estimation of gas hydrate and free gas saturation

Attenuations of different types of gas hydrate cementation in fluid-saturated porous solids are discussed. The factors affecting estimation of gas hydrate and free gas saturation are analyzed. It is suggested that porosity of sediment, the P wave velocity model and methods of calculating elastic modulus are key factors in the estimation of gas hydrate and free gas saturations. Attenuation of gas hydrate-bearing sediment is closely related with the cementation types of gas hydrate. Negative anomalies of quality factors indicate that gas hydrate deposits away from grain as part of fluid. Positive anomalies of the quality factors indicate that gas hydrate contacts with solid and changes the elastic modulus of matrix. Low frequency velocity and high frequency velocity models are used to estimate gas hydrate and free gas saturation in the Blake Ridge area according to the well log data of the hole 995 in ODP leg 164. The gas hydrate saturation obtained by low frequency velocity is 10% similar to 20% of the pore space and free gas saturation is 0.5% similar to 1% of the pore space. The gas hydrate saturation obtained by high frequency velocity is 5% similar to 10% of the pore space and free gas saturation is 1% similar to 2% of the pore space.

Bottom simulating reflector and gas seepage in Okinawa Trough: Evidence of gas hydrate in an active back-arc basin

To look for gas hydrate, 22 multi-channel and 3 single-channel seismic lines on the East China Sea (ECS) shelf slope and at the bottom of the Okinawa Trough were examined. It was found that there was indeed bottom simulating reflector (BSR) occurrence, but it is very rare. Besides several BSRs, a gas seepage was also found. As shown by the data, both the BSR and gas seepage are all related with local geological structures, such as mud diapir, anticline, and fault-controlled graben-like structure. However, similar structural "anomalies" are quite common in the tectonically very active Okinawa Trough region, but very few of them have developed BSR or gas seepage. The article points out that the main reason is probably the low concentration of organic carbon of the sediment in this area. It was speculated that the rare occurrence of gas hydrates in this region is governed by structure-controlled fluid flow. Numerous faults and fractures form a network of high-permeability channels in the sediment and highly fractured igneous basement to allow fluid circulation and ventilation. Fluid flow in this tectonic environment is driven primarily by thermal buoyancy and takes place on a wide range of spatial scales. The fluid flow may play two roles to facilitate hydrate formation: to help gather enough methane into a small area and to modulate the thermal regime.

Gas Hydrate Inhibition: A Review of the Role of Ionic Liquids

Ionic liquids (ILs) are popular designer green chemicals with great potential for use in diverse energy-related applications. Apart from the well-known low vapor pressure, the physical properties of ILs, such as hydrogen-bond-forming capacity, physical state, shape, and size, can be fine-tuned for specific applications. Natural gas hydrates are easily formed in gas pipelines and pose potential problems to the oil and natural gas industry, particularly during deep-sea exploration and production. This review summarizes the recent advances in IL research as dual-function gas hydrate inhibitors. Almost all of the available thermodynamic and kinetic inhibition data in the presence of ILs have been systematically reviewed to evaluate the efficiency of ILs in gas hydrate inhibition, compared to other conventional thermodynamic and kinetic gas hydrate inhibitors. The principles of natural gas hydrate formation, types of gas hydrates and their inhibitors, apparatuses and methods used, reported experimental data, and theoretical methods are thoroughly and critically discussed. The studies in this field will facilitate the design of advanced ILs for energy savings through the development of efficient low-dosage gas hydrate inhibitors.