Equilibrium studies of ammonium exchange with Australian natural zeolites

This paper is concerned with the study of the equilibrium exchange of ammonium ions with two natural zeolite samples sourced in Australia from Castle Mountain Zeolites and Zeolite Australia. A range of sorption models including Langmuir Vageler, Competitive Langmuir, Freundlich, Temkin, Dubinin Astakhov and Brouers–Sotolongo were applied in order to gain an insight as to the exchange process. In contrast to most previous studies, non-linear regression was used in all instances to determine the best fit of the experimental data. Castle Mountain natural zeolite was found to exhibit higher ammonium capacity than Zeolite Australia material when in the freshly received state, and this behavior was related to the greater amount of sodium ions present relative to calcium ions on the zeolite exchange sites. The zeolite capacity for ammonium ions was also found to be dependent on the solution normality, with 35–60% increase inuptake noted when increasing the ammonium concentration from 250 to 1000 mg/L. The optimal fit ofthe equilibrium data was achieved by the Freundlich expression as confirmed by use of Akaikes Information Criteria. It was emphasized that the bottle-point method chosen influenced the isotherm profile in several ways, and could lead to misleading interpretation of experiments, especially if the constant zeolite mass approach was followed. Pre-treatment of natural zeolite with acid and subsequently sodium hydroxide promoted the uptake of ammonium species by at least 90%. This paper highlighted the factors which should be taken into account when investigating ammonium ion exchange with natural zeolites.

Factors influencing kinetic and equilibrium behaviour of sodium ion exchange with strong acid cation resin

This study reports an investigation of the ion exchange treatment of sodium chloride solutions in relation to use of resin technology for applications such as desalination of brackish water. In particular, a strong acid cation (SAC) resin (DOW Marathon C) was studied to determine its capacity for sodium uptake and to evaluate the fundamentals of the ion exchange process involved. Key questions to answer included: impact of resin identity; best models to simulate the kinetics and equilibrium exchange behaviour of sodium ions; difference between using linear least squares (LLS) and non-linear least squares (NLLS) methods for data interpretation; and, effect of changing the type of anion in solution which accompanied the sodium species. Kinetic studies suggested that the exchange process was best described by a pseudo first order rate expression based upon non-linear least squares analysis of the test data. Application of the Langmuir Vageler isotherm model was recommended as it allowed confirmation that experimental conditions were sufficient for maximum loading of sodium ions to occur. The Freundlich expression best fitted the equilibrium data when analysing the information by a NLLS approach. In contrast, LLS methods suggested that the Langmuir model was optimal for describing the equilibrium process. The Competitive Langmuir model which considered the stoichiometric nature of ion exchange process, estimated the maximum loading of sodium ions to be 64.7 g Na/kg resin. This latter value was comparable to sodium ion capacities for SAC resin published previously. Inherent discrepancies involved when using linearized versions of kinetic and isotherm equations were illustrated, and despite their widespread use, the value of this latter approach was questionable. The equilibrium behaviour of sodium ions form sodium fluoride solution revealed that the sodium ions were now more preferred by the resin compared to the situation with sodium chloride. The solution chemistry of hydrofluoric acid was suggested as promoting the affinity of the sodium ions to the resin.

Environmental applications of inorganic-organic clays for recalcitrant organic pollutants removal: Bisphenol A

Bisphenol-A (BPA) adsorption onto inorganic-organic clays (IOCs) was investigated. For this purpose, IOCs synthesised using octadecyltrimethylammonium bromide (ODTMA, organic modifier) and hydroxy aluminium (Al13, inorganic modifier) were used. Three intercalation methods were employed with varying ODTMA concentration in the synthesis of IOCs. Molecular interactions of clay surfaces with ODTMA and Al13 and their arrangements within the interlayers were determined using Fourier transform infrared spectroscopy (FTIR). Surface area and porous structure of IOCs were determined by applying Brunauer, Emmett, and Teller (BET) method to N2 adsorption-desorption isotherms. Surface area decreased upon ODTMA intercalation while it increased with Al13 pillaring. As a result, BET specific surface area of IOCs was considerably higher than those of organoclays. Initial concentration of BPA, contact time and adsorbent dose significantly affected BPA adsorption into IOCs. Pseudo-second order kinetics model is the best fit for BPA adsorption into IOCs. Both Langmuir and Freundlich adsorption isotherms were applicable for BPA adsorption (R2 > 0.91) for IOCs. Langmuir maximum adsorption capacity for IOCs was as high as 109.89 mg g‒1 and it was closely related to the loaded ODTMA amount into the clay. Hydrophobic interactions between long alkyl chains of ODTMA and BPA are responsible for BPA adsorption into IOCs.

Abatement of fluoride from water using manganese dioxide-coated activated alumina

Batch adsorption of fluoride onto manganese dioxide-coated activated alumina (MCAA) has been studied. Adsorption experiments were carried out at various pH (3–9), time interval (0–6 h), adsorbent dose (1–16 g/l), initial fluoride concentration (1–25 mg/l) and in the presence of different anions. Adsorption isotherms have been modeled using Freundlich, Langmuir and Dubinin–Raduskevich isotherms and adsorption followed Langmuir isotherm model. Kinetic studies revealed that the adsorption followed second-order rate kinetics. MCAA could remove fluoride effectively (up to 0.2 mg/l) at pH 7 in 3 h with 8 g/l adsorbent dose when 10 mg/l of fluoride was present in 50 ml of water. In the presence of other anions, the adsorption of fluoride was retared. The mechanism of fluoride uptake by MCAA is due to physical adsorption as well as through intraparticle diffusion which was confirmed by kinetics, Dubinin–Raduskevich isotherm, zeta-potential measurements and mapping studies of energy-dispersive analysis of X-ray.

Adsorption of anionic dyes on chitosan grafted poly(alkyl methacrylate)s

Chitosan grafted poly(alkyl methacrylate)s (namely chitosan grafted poly(methyl methacrylate) (ChgPMMA), chitosan grafted poly(ethyl methacrylate)(ChgPEMA), chitosan grafted poly(butyl methacrylate) (ChgPBMA) and chitosan grafted poly(hexyl methacrylate) (ChgPHMA)) were synthesized and characterized by using FT-IR and C-13 NMR techniques. The adsorption batch experiments on these grafted copolymers were conducted by using an anionic sulfonated dye. Orange-G. A pseudo-second-order kinetic model was used to determine the kinetics of adsorption. The effect of grafting, effect of process variables and the effect of different sulfonated anionic dyes (Orange-C, Congo Red, Remazol Brill Blue R and Methyl Blue) on the adsorption kinetics was determined. The Langmuir and Freundlich models were used to fit the adsorption isotherms and from the values of correlation coefficients (R-2), it was observed that the experimental data fits very well to the Langmuir model. The values of the maximum adsorption capacity of the adsorbents follow the order: ChgPMMA > ChgPEMA > ChgPBMA > ChgPHMA > chitosan. (C) 2010 Elsevier B.V. All rights reserved.

Studies on interaction of colloidal Ag nanoparticles with Bovine Serum Albumin (BSA)

Biofunctionalization of noble metal nanoparticles like Ag, Au is essential to obtain biocompatibility for specific biomedical applications. Silver nanciparticles are being increasingly used in bio-sensing applications owing to excellent optoelectronic properties. Among the serum albumins, the most abundant proteins in plasma, a wide range of physiological functions of Bovine Serum Albumin (BSA) has made it a model system for biofunctionalization. In absence of adequate prior reports, this study aims to investigate the interaction between silver nanoparticles and BSA. The interaction of BSA [0.05-0.85% concentrations] with Ag nanoparticles [50 ppm concentration] in aqueous dispersion was Studied through UV-vis spectral changes, morphological and surface structural changes. At pH 7, which is More than the isoelectric point of BSA, a decrease in absorbance at plasmon peak of uninteracted nanciparticles (425 mn) was noted till 0.45% BSA, beyond that a blue shift towards 410 urn was observed. The blue shift may be attributed to enhanced electron density on the particle surfaces. Increasing pH to 12 enhanced the blue shift further to 400 rim. The conformational changes in BSA at alkaline pH ranges and consequent hydrophobic interactions also played an important role. The equilibrium adsorption data fitted better to Freundlich isotherm compared to Langmuir Curve. The X-ray diffraction study revealed complete coverage of Ag nanoparticles by BSA. The scanning electron microscopic study of the interacted nanoparticles was also carried Out to decipher morphological changes. This study established that tailoring the concentration of BSA and pH of the interaction it was possible to reduce aggregation of nanoparticles. Biofunctionalized Ag nanoparticles with reduced aggregation will be more amenable towards bio-sensing applications. (C) 2009 Elsevier B.V. All rights reserved.

Biosorption of iron(III) from aqueous solutions using the husk of Cicer arientinum

Iron is a major pollutant released as a by-product during several industrial operations especially during acid mining of metal ores. In this paper, the use of Bengal gram husk (husk of channa dal, Cicer arientinum) in the biosorption of Fe(III) from aqueous solutions is discussed. Parameters like agitation time, adsorbent dosage and pH were studied at different Fe(Ill) concentrations. The adsorption data fit well with Langmuir and Freundlich isotherm models. The adsorption capacity (q(max)) calculated from the Langmuir isotherm was 72.16 mg of Fe(III)/g of the biosorbent at an initial pH of 2.5. Desorption Studies were performed at different concentrations of hydrochloric acid showing that quantitative recovery of the metal ion is possible. The infrared spectra of the biomass before and after treatment with Fe(III), revealed that hydroxyl, carboxyl and amide bonds are involved in the uptake of Fe(III) ions.

Removal of hexavalent chromium using coffee husk

The potential to remove chromium(VI) from aqueous solutions through biosorption using coffee husk was investigated. The effects of pH, contact time, initial concentration and adsorbent dosage on the adsorption of Cr(VI) were studied. The data obeyed Langmuir and Freundlich adsorption isotherms. The Langmuir adsorption capacity was found to be 44.95 mg/g. The Freundlich constants K-f and n were 1.027 mg/g (litre/mg)(n)] and 1.493, respectively. Desorption studies indicated the removal of 60% of the hexavalent chromium. Infrared spectral studies revealed the presence of functional groups, such as hydroxyl and carboxyl groups, on the surface of the biomass, which facilitates biosorption of Cr(VI).

Rapid Synthesis of Ultrahigh Adsorption Capacity Zirconia by a Solution Combustion Technique

Tetragonal ZrO2 was synthesized by the solution combustion technique using glycine as the fuel. The compound was characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, infrared spectroscopy, and BET surface area analysis. The ability of this compound to adsorb dyes was investigated, and the compound had a higher adsorption capacity than commercially activated carbon. Infrared spectroscopic observations were used to determine the various interactions and the groups responsible for the adsorption activity of the compound. The effects of the initial concentration of the dye, temperature, adsorbent concentration, and pH of the solution were studied. The kinetics of adsorption was described as a first-order process, and the relative magnitudes of internal and external mass transfer processes were determined. The equilibrium adsorption was also determined and modeled by a composite Langmuir-Freundlich isotherm.

Purifying water containing both anionic and cationic species using a (Zn, Cu)O, ZnO, and Cobalt Ferrite based multiphase adsorbent system

For the purpose of water purification, novel and low-cost adsorbents which are promising replacements for activated carbon are being actively pursued. However, a single-phase material that adsorbs both cationic and anionic species remains elusive. Hence, a low-cost, multiphase adsorbent bed that purifies water containing both anionic and cationic pollutants is a desirable alternative. We choose anionic (Congo red, Orange G) and cationic (methylene blue, malachite green) dyes as model pollutants. These dyes are chosen since they are widely found in effluents from textile, leather, fishery, and pharmaceutical industries, and their carcinogenic, mutagenic, genotoxic, and cytotoxic impact on mammalian cells is well-established. We show that ZnO, (Zn0.24Cu0.76)O and cobalt ferrite based multiphase fixed adsorbent bed efficiently adsorbs model anionic (Congo red, Orange G) and cationic (methylene blue and malachite green) pollutants, and their complex mixtures. All adsorbent phases are synthesized using room-temperature, high-yield (similar to 96-100%), green chemical processes. The nanoadsorbents are characterized by using X-ray powder diffraction (XRD), scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET) surface area analysis, and zeta potential measurements. The constituent nanophases are deliberately chosen to be beyond 50 nm, in order to avoid the nanotoxic size regime of oxides. Adsorption characteristics of each of the phases are examined. Isotherm based analysis shows that adsorption is both spontaneous and highly favorable. zeta potential measurements indicate that electrostatic interactions are the primary driving force for the observed adsorption behavior. The isotherms obtained are best described using a composite Langmuir-Freundlich model. Pseudo-first-order, rapid kinetics is observed (with adsorption rate constants as high as 0.1-0.2 min(-1) in some cases). Film diffusion is shown to be the primary mechanism of adsorption.

Local stability of a gravitating filament: a dispersion relation

Filamentary structures are ubiquitous in astrophysics and are observed at various scales. On a cosmological scale, matter is usually distributed along filaments, and filaments are also typical features of the interstellar medium. Within a cosmic filament, matter can contract and form galaxies, whereas an interstellar gas filament can clump into a series of bead-like structures that can then turn into stars. To investigate the growth of such instabilities, we derive a local dispersion relation for an idealized self-gravitating filament and study some of its properties. Our idealized picture consists of an infinite self-gravitating and rotating cylinder with pressure and density related by a polytropic equation of state. We assume no specific density distribution, treat matter as a fluid, and use hydrodynamics to derive the linearized equations that govern the local perturbations. We obtain a dispersion relation for axisymmetric perturbations and study its properties in the (kR, kz) phase space, where kR and kz are the radial and longitudinal wavenumbers, respectively. While the boundary between the stable and unstable regimes is symmetrical in kR and kz and analogous to the Jeans criterion, the most unstable mode displays an asymmetry that could constrain the shape of the structures that form within the filament. Here the results are applied to a fiducial interstellar filament, but could be extended for other astrophysical systems, such as cosmological filaments and tidal tails.

Stability of Filaments in Star-Forming Clouds and the Formation of Prestellar Cores in Them

The exact process(es) that generate(s) dense filaments which then form prestellar cores within them is unclear. Here we study the formation of a dense filament using a relatively simple set-up of a pressure-confined, uniform-density cylinder. We examine if its propensity to form a dense filament and further, to the formation of prestellar cores along this filament, bears on the gravitational state of the initial volume of gas. We report a radial collapse leading to the formation of a dense filamentary cloud is likely when the initial volume of gas is at least critically stable (characterised by the approximate equality between the mass line-density for this volume and its maximum value). Though self-gravitating, this volume of gas, however, is not seen to be in free-fall. This post-collapse filament then fragments along its length due to the growth of a Jeans-like instability to form prestellar cores. We suggest dense filaments in typical star-forming clouds classified as gravitationally super-critical under the assumption of: (i) isothermality when in fact, they are not, and (ii) extended radial profiles as against pressure-truncated, that significantly over-estimates their mass line-density, are unlikely to experience gravitational free-fall. The radial density and temperature profile derived for this post-collapse filament is consistent with that deduced for typical filamentary clouds mapped in recent surveys of nearby star-forming regions.

Biossorção de tório e urânio pela macroalga marinha sargassum filipendula

Por ser um material de baixo custo e apresentar propriedades ligantes, a macroalga marinha Sargassum filipendula vem sendo utilizada como material biossorvente no processo de biossorção de metais. No presente trabalho a alga marrom foi utilizada no estudo cinético e de equilíbrio dos íons de tório e urânio individuais e os resultados comparados à biossorção desses metais em sistema binário. Os testes foram realizados nas concentrações 1 e 10 mg/L e pH= 1,0 e 4,0 na temperatura de 25 1C. A melhor condição para biossorção de tório foi encontrada para 1 mg/L e pH= 1,0, enquanto que para urânio foi em 1 mg/L e pH= 4,0. O estudo cinético de biossorção de tório mostrou que o modelo de segunda ordem descreve melhor os dados experimentais em 1 mg/L (R2= 0,9987) e 10 mg/L (R2= 0,9919) em pH= 1,0 e 1 mg/L (R2= 0,9976) em pH= 4,0, enquanto em 10 mg/L (R2= 0,9787) pH= 4,0 a curva encontrada representou uma cinética de primeira ordem. Para a cinética de urânio os dois modelos se adequaram bem aos dados em ambas as condições experimentais. O estudo de equilíbrio mostrou um perfil crescente de captação de tório, com uma remoção de 96% e 54% do metal em pH= 1,0 e 4,0, respectivamente, a partir da Co= 1 mg/L. A melhor eficiência de captação dos íons de urânio foi de 33% para Co= 100 mg/L em pH= 1,0 e 71% para Co= 1 mg/L em pH= 4,0. Os dados experimentais da isoterma de tório mostraram-se mais adequados ao modelo de Freundlich para pH= 1,0, enquanto que para o pH= 4,0 esses foram melhor representados pelo modelo de Langmuir, com valores de coeficiente de determinação superiores. Em relação à isoterma do urânio, o modelo de Freundlich representou bem os dados experimentais. Os parâmetros de equilíbrio calculados a partir do modelo de Langmuir (kL, qmax ) e Freundlich (kF, n) indicaram uma maior afinidade da biomassa pelos íons de tório em ambas as condições experimentais. O estudo de equilíbrio do sistema binário mostrou que a biossorção dos íons de tório não é afetada pela presença do urânio em solução. Por outro lado, a sorção do urânio foi fortemente afetada pela coexistência com os íons de tório.

Biossorção de vanádio pela macroalga marinha Sargassum filipendula

Muitos biossorventes naturais têm sido pesquisados por possuírem baixo custo e apresentarem propriedades ligantes, como é o caso da macroalga marinha Sargassum filipendula (S. filipendula) que vem sendo utilizada como material biossorvente no processo de biossorção de metais pesados. No presente trabalho a alga marrom foi utilizada para estudos realizados em batelada, onde se determinou o pH ideal de biossorção de vanádio, a relação sólido/líquido ideal e a importância da velocidade de agitação. O estudo cinético e de equilíbrio dos íons metálicos também foram realizados em bateladas nas seguintes condições de ensaio: (1) 0,10 g de biomassa, 25,0 mL de solução de vanádio igual a 18,0 mg L-1, temperatura 25,0 C e 150 rpm de agitação; (2) 0,10 g de biomassa, 25,0 mL de solução de vanádio igual a 36,0 mg L-1, temperatura 25,0 C e 150 rpm de agitação. A melhor condição para biossorção de vanádio foi encontrada para 36,0 mg L-1 e pH= 2,0. O estudo cinético de biossorção de vanádio mostrou que o modelo de segunda ordem descreve melhor os dados experimentais em 36,0 mg L-1 (R2= 0,9825). O estudo de equilíbrio mostrou um perfil crescente de remoção de vanádio. A melhor eficiência de captação dos íons de vanádio foi de 61,0 % para Co= 40,0 mg L-1 em pH= 2,0. Os dados experimentais da isoterma de vanádio mostraram-se mais adequados ao modelo de Langmuir para pH= 2,0, Os parâmetros de equilíbrio calculados a partir do modelo de Langmuir (b, qmax ) 0,009 e 43,3 mg/g, respectivamente, corroboram melhor para a interpretação dos resultados quando comparados com o modelo de Freundlich (kF, n) 1,56 e 2,41, visto que o coeficiente de correlação é maior para Langmuir

Biossorção de tório com emprego de Sargassum filipendula

Com o aumento do rigor para descarte de efluentes contaminado com metais pesados, as pesquisas têm se intensificado na busca de métodos de remoção, que tragam bons resultados de captação dos metais, aliado a um baixo custo. O uso de biomassas como bactérias, fungos e algas marinhas como material adsorvente, tem se apresentado como uma alternativa, principalmente para soluções com baixo teor de metais. Neste trabalho, a alga marinha Sargassum filipendula foi avaliada na sua capacidade de remoção do metal tório de uma solução sintética e do efluente dos laboratórios de análises ambientais do IRD. A cinética desta biossorção foi estudada em regime de batelada e o equilíbrio foi alcançado com 180 min de reação. Dois modelos cinéticos foram utilizados nesta avaliação, um de primeira ordem e um modelo de pseudo segunda ordem, tendo o modelo de segunda ordem apresentado um melhor ajuste dos dados. Na avaliação da capacidade máxima de captação do tório pela biomassa marinha em regime de batelada, foi construída a isoterma que apresentou um perfil crescente na captação alcançando um máximo de 2,59 mol/g. Os modelos de Langmuir e Freundlich foram utilizados para ajustar os dados da isoterma, tendo apresentado maior correlação com os dados o modelo de Langmuir, resultando num valor de captação máxima calculado pelo modelo de 2,92 mol/g. A capacidade de remoção do metal tório da alga Sargassum filipendula também foi avaliada em regime contínuo. Um estudo de altura crítica de leito foi realizado preenchendo-se uma coluna com diferentes massas de alga correspondendo a diferentes alturas de leito. A concentração de tório residual foi quantificada na solução de saída e a menor concentração na saída foi alcançada com 40 cm de leito ou 96 g de biomassa. Após este estudo um sistema contínuo com duas colunas, com 96 g de biomassa cada, e uma bomba peristáltica foi utilizado para o tratamento do efluente real do IRD, contendo não apenas o metal tório, mas outros metais como urânio, cálcio, cromo, ferro, chumbo, etc. Cento e cinco litros de efluente foram tratados numa concentração de 6 mg/L, a concentração do efluente de saída foi de 3,75 mg/L. A caracterização do efluente quanto aos metais presentes foi realizada em ICP-MS, os resultados demonstraram que não houve competição pelos sítios ligantes da biomassa entre o tório e os demais metais. Além disso, alguns metais como cálcio, ferro e magnésio, tiveram um aumento na concentração de saída indicando a presença do mecanismo de troca iônica na biossorção do tório por Sargassum filipendula