Field effect and light-assisted a-Si:H sensors for detection of ions in solution

In this paper we present an amorphous silicon device that can be used in two operation modes to measure the concentration of ions in solution. While crystalline devices present a higher sensitivity, their amorphous counterpart present a much lower fabrication cost, thus enabling the production of cheap disposable sensors for use, for example, in the food industry. The devices were fabricated on glass substrates by the PECVD technique in the top gate configuration, where the metallic gate is replaced by an electrolytic solution with an immersed Ag/AgCl reference electrode. Silicon nitride is used as gate dielectric enhancing the sensitivity and passivation layer used to avoid leakage and electrochemical reactions. In this article we report on the semiconductor unit, showing that the device can be operated in a light-assisted mode, where changes in the pH produce changes on the measured ac photocurrent. In alternative the device can be operated as a conventional ion selective field effect device where changes in the pH induce changes in the transistor's threshold voltage.

Handheld-assisted field data collection for occupational risk assessment.

A computerized handheld procedure is presented in this paper. It is intended as a database complementary tool, to enhance prospective risk analysis in the field of occupational health. The Pendragon forms software (version 3.2) has been used to implement acquisition procedures on Personal Digital Assistants (PDAs) and to transfer data to a computer in an MS-Access format. The data acquisition strategy proposed relies on the risk assessment method practiced at the Institute of Occupational Health Sciences (IST). It involves the use of a systematic hazard list and semi-quantitative risk assessment scales. A set of 7 modular forms has been developed to cover the basic need of field audits. Despite the minor drawbacks observed, the results obtained so far show that handhelds are adequate to support field risk assessment and follow-up activities. Further improvements must still be made in order to increase the tool effectiveness and field adequacy.

Advantages of using nested collision induced dissociation/post-source decay with matrix-assisted laser desorption/ionization time-of-flight mass spectrometry: sequencing of novel peptides from wasp venom

We have examined the applicability of the 'nested' collision induced dissociation/post-source decay (CID/PSD) method to the sequencing of novel peptides from solitary wasps which have neurotoxic venom for paralyzing other insects. The CID/PSD spectrum of a ladder peptide derived from an exopeptidase digest was compared with that of the intact peptide. The mass peaks observed only in the CID/PSD spectrum of a ladder peptide were extracted as C-terminal fragment ions. Assignment of C-terminal fragment ions enabled calculation of N-terminal fragment masses, leading to differentiation between N-terminal fragment ions and internal fragment ions. This methodology allowed rapid and sensitive identification by removing ambiguity in the assignment of the fragment ions, and proved useful for sequencing unknown peptides, in particular those available as natural products with a limited supply. Copyright (C) 2000 John Wiley & Sons, Ltd.

Numerical study of the laser-tip coupling in surface plasmon assisted stacked-double-gate field emitter arrays

Recently, sub-wavelength-pitch stacked double-gate metal nanotip arrays have been proposed to realize high current, high brightness electron bunches for ultrabright cathodes for x-ray free-electron laser applications. With the proposed device structure, ultrafast field emission of photoexcited electrons is efficiently driven by vertical incident near infrared laser pulses, via near field coupling of the surface plasmon polariton resonance of the gate electrodes with the nanotip apex. In this work, in order to gain insight in the underlying physical processes, the authors report detailed numerical studies of the proposed device. The results indicate the importance of the interaction of the double-layer surface plasmon polariton, the position of the nanotip, as well as the incident angle of the near infrared laser pulses.

Plasma diagnostics and ITO film deposition by RF-assisted closed-field dual magnetron system

Deposition of indium tin oxide (ITO) among various transparent conductive materials on flexible organic substrates has been intensively investigated among academics and industrials for a whole new array of imaginative optoelectronic products. One critical challenge coming with the organic materials is their poor thermal endurances, considering that the process currently used to produce industry-standard ITO usually involves relatively high substrate temperature in excess of 200°C and post-annealing. A lower processing temperature is thus demanded, among other desires of high deposition rate, large substrate area, good uniformity, and high quality of the deposited materials. For this purpose, we developed an RF-assisted closed-field dual magnetron sputtering system. The “prototype” system consists of a 3-inch unbalanced dual magnetron operated at a closed-field configuration. An RF coil was fabricated and placed between the two magnetron cathodes to initiate a secondary plasma. The concept is to increase the ionization faction with the RF enhancement and utilize the ion energy instead of thermal energy to facilitate the ITO film growth. The closed-field unbalanced magnetrons create a plasma in the intervening region rather than confine it near the target, thus achieving a large-area processing capability. An RF-compensated Langmuir probe was used to characterize and compare the plasmas in mirrored balanced and closed-field unbalanced magnetron configurations. The spatial distributions of the electron density ne and electron temperature Te were measured. The density profiles reflect the shapes of the plasma. Rather than intensively concentrated to the targets/cathodes in the balanced magnetrons, the plasma is more dispersive in the closed-field mode with a twice higher electron density in the substrate region. The RF assistance significantly enhances ne by one or two orders of magnitude higher. The effect of various other parameters, such as pressure, on the plasma was also studied. The ionization fractions of the sputtered atoms were measured using a gridded energy analyzer (GEA) combined with a quartz crystal microbalance (QCM). The presence of the RF plasma effectively increases the ITO ionization fraction to around 80% in both the balanced and closed-field unbalanced configurations. The ionization fraction also varies with pressure, maximizing at 5-10 mTorr. The study of the ionization not only facilitates understanding the plasma behaviors in the RF-assisted magnetron sputtering, but also provides a criterion for optimizing the film deposition process. ITO films were deposited on both glass and plastic (PET) substrates in the 3-inch RF-assisted closed-field magnetrons. The electrical resistivity and optical transmission transparency of the ITO films were measured. Appropriate RF assistance was shown to dramatically reduce the electrical resistivity. An ITO film with a resistivity of 1.2×10-3 Ω-cm and a visible light transmittance of 91% was obtained with a 225 W RF enhancement, while the substrate temperature was monitored as below 110°C. X-ray photoelectron spectroscopy (XPS) was employed to confirm the ITO film stoichiometry. The surface morphology of the ITO films and its effect on the film properties were studied using atomic force microscopy (AFM). The prototype of RF-assisted closed-field magnetron was further extended to a larger rectangular shaped dual magnetron in a flat panel display manufacturing system. Similar improvement of the ITO film conductivities by the auxiliary RF was observed on the large-area PET substrates. Meanwhile, significant deposition rates of 25-42 nm/min were achieved.

Supercritical Carbon Dioxide Extraction Of Capsaicinoids From Malagueta Pepper (capsicum Frutescens L.) Assisted By Ultrasound.

Extracts from malagueta pepper (Capsicum frutescens L.) were obtained using supercritical fluid extraction (SFE) assisted by ultrasound, with carbon dioxide as solvent at 15MPa and 40°C. The SFE global yield increased up to 77% when ultrasound waves were applied, and the best condition of ultrasound-assisted extraction was ultrasound power of 360W applied during 60min. Four capsaicinoids were identified in the extracts and quantified by high performance liquid chromatography. The use of ultrasonic waves did not influence significantly the capsaicinoid profiles and the phenolic content of the extracts. However, ultrasound has enhanced the SFE rate. A model based on the broken and intact cell concept was adequate to represent the extraction kinetics and estimate the mass transfer coefficients, which were increased with ultrasound. Images obtained by field emission scanning electron microscopy showed that the action of ultrasonic waves did not cause cracks on the cell wall surface. On the other hand, ultrasound promoted disturbances in the vegetable matrix, leading to the release of extractable material on the solid surface. The effects of ultrasound were more significant on SFE from larger solid particles.

Dynamics of trapped Bose-Einstein condensates: Beyond the mean-field

Since dilute Bose gas condensates were first experimentally produced, the Gross-Pitaevskii equation has been successfully used as a descriptive tool. As a mean-field equation, it cannot by definition predict anything about the many-body quantum statistics of condensate. We show here that there are a class of dynamical systems where it cannot even make successful predictions about the mean-field behavior, starting with the process of evaporative cooling by which condensates are formed. Among others are parametric processes, such as photoassociation and dissociation of atomic and molecular condensates.

Development of biocompatible and “smart” porous structures using CO2-assisted processes

Dissertação apresentada para a obtenção do grau de Doutor em Engenharia Química, especialidade Engenharia da Reacção Química, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

InOx thin films deposited by plasma assisted evaporation: application in light shutters

An integration of undoped InOx and commercial ITO thin films into laboratory assembled light shutter devices is made. Accordingly, undoped transparent conductive InOx thin films, about 100 nm thick, are deposited by radiofrequency plasma enhanced reactive thermal evaporation (rf-PERTE) of indium teardrops with no intentional heating of the glass substrates. The process of deposition occurs at very low deposition rates (0.1-0.3 nm/s) to establish an optimized reaction between the oxygen plasma and the metal vapor. These films show the following main characteristics: transparency of 87% (wavelength, lambda = 632.8 nm) and sheet resistance of 52 Omega/sq; while on commercial ITO films the transparency was of 92% and sheet resistance of 83 Omega/sq. The InOx thin film surface characterized by AFM shows a uniform grain texture with a root mean square surface roughness of Rq similar to 2.276 nm. In contrast, commercial ITO topography is characterized by two regions: one smoother with Rq similar to 0.973 nm and one with big grains (Rq similar to 3.617 nm). For the shutters assembled using commercial ITO, the light transmission coefficient (Tr) reaches the highest value (Tr-max) of 89% and the lowest (Tr-min) of 1.3% [13], while for the InOx shutters these values are 80.1% and 3.2%, respectively. Regarding the electric field required to achieve 90% of the maximum transmission in the ON state (E-on), the one presented by the devices assembled with commercial ITO coated glasses is 2.41 V/mu m while the one presented by the devices assembled with InOx coated glasses is smaller, 1.77 V/mu m. These results corroborate the device quality that depends on the base materials and fabrication process used. (C) 2014 Elsevier Ltd. All rights reserved.

Atomic force microscopy assisted with electron and ion beam microscopy for the direct measurement of biostructures and DNA samples

Dissertation to obtain a Master degree in Biotechnology

eHealth e a adoção da inovação em assisted living technologies : o caso das demências

RESUMO - Assistimos hoje a um contexto marcado (i) pelo progressivo envelhecimento das sociedades ocidentais, (ii) pelo aumento da prevalência das doenças crónicas, de que as demências são um exemplo, (iii) pelo significativo aumento dos custos associados a estas patologias, (iv) por orçamentos públicos fortemente pressionadas pelo controlo da despesa, (v) por uma vida moderna que dificulta o apoio intergeracional, tornando o suporte proporcionado pelos filhos particularmente difícil, (vi) por fortes expectativas relativamente à prestação de cuidados de saúde com qualidade. Teremos assim de ser capazes de conseguir melhorar os serviços de saúde, ao mesmo tempo que recorremos a menos recursos financeiros e humanos, pelo que a inovação parece ser crítica para a sustentabilidade do sistema. Contudo a difusão das Assistive Living Technologies, apesar do seu potencial, tem sido bastante baixa, nomeadamente em Portugal. Porquê? Hamer, Plochg e Moreira (2012), no editorial do International Journal of Healthcare Management, enquadram a Inovação como “podendo ser imprevisível e mesmo dolorosa, pelo que talvez possamos não ficar surpreendidos se surgirem resistências e que, inovações bastante necessárias, capazes de melhorar os indicadores de saúde, tenham sido de adoção lenta ou que tenham mesmo sido insustentáveis”. Em Portugal não há bibliografia que procure caracterizar o modelo de difusão da inovação em eHealth ou das tecnologias de vivência assistida. A bibliografia internacional é igualmente escassa. O presente projeto de investigação, de natureza exploratória, tem como objetivo principal, identificar barreiras e oportunidades para a implementação de tecnologias eHealth, aplicadas ao campo das demências. Como objetivos secundários pretendemse identificar as oportunidades e limitações em Portugal: mapa de competências nacionais, e propor medidas que possa acelerar a inovação em ALT, no contexto nacional. O projeto seguirá o modelo de um estudo qualitativo. Para o efeito foram conduzidas entrevistas em profundidade junto de experts em ALT, procurando obter a visão daqueles que participam do lado da Oferta- a Indústria; do lado da Procura- doentes, cuidadores e profissionais de saúde; bem como dos Reguladores. O instrumento utilizado para a recolha da informação pretendida foi o questionário não estruturado. A análise e interpretação da informação recolhida foram feitas através da técnica de Análise de Conteúdo. Os resultados da Análise de Conteúdo efetuada permitiram expressar a dicotomia barreira/oportunidade, nas seguintes categorias aqui descritas como contextos (i) Contexto Tecnológico, nas subcategorias de Acesso às Infraestruturas; Custo da Tecnologia; Interoperabilidade, (ii) Contexto do Valor Percecionado, nas subcategorias de Utilidade; Eficiência; Divulgação, (iii) Contexto Político, compreendendo a Liderança; Organização; Regulação; Recursos, (iv) Contexto Sociocultural, incluindo nomeadamente Idade; Literacia; Capacidade Económica, (v) Contexto Individual, incluindo como subcategorias, Capacidade de Adaptação a Novas tecnologias; Motivação; Acesso a equipamentos (vi) Contexto Específico da Doença, nomeadamente o Impacto Cognitivo; Tipologia Heterogénea e a Importância do Cuidador. Foi proposto um modelo exploratório, designado de Modelo de Contextos e Forças, que estudos subsequentes poderão validar. Neste modelo o Contexto Tecnológico é um Força Básica ou Fundamental; o Contexto do Valor Percecionado, constitui-se numa Força Crítica para a adoção de inovação, que assenta na sua capacidade para oferecer valor aos diversos stakeholders da cadeia de cuidados. Temos também o Contexto Político, com capacidade de modelar a adoção da inovação e nomeadamente com capacidade para o acelerar, se dele emitir um sinal de urgência para a mudança. O Contexto Sociocultural e Individual expressam uma Força Intrínseca, dado que elas são características internas, próprias e imutáveis no curto-prazo, das sociedade e das pessoas. Por fim há que considerar o Contexto Específico da Doença, nesta caso o das demências. Das conclusões do estudo parece evidente que as condições tecnológicas estão medianamente satisfeitas em Portugal, com evidentes progressos nos últimos anos (exceção para a interoperabilidade aonde há necessidade de maiores progressos), não constituindo portanto barreira à introdução de ALT. Aonde há necessidade de investir é nas áreas do valor percebido. Da análise feita, esta é uma área que constitui uma barreira à introdução e adoção das ALT em Portugal. A falta de perceção do valor que estas tecnologias trazem, por parte dos profissionais de saúde, doentes, cuidadores e decisores políticos, parece ser o principal entrave à sua adoção. São recomendadas estratégias de modelos colaborativos de Investigação e Desenvolvimento e de abordagens de cocriação com a contribuição de todos os intervenientes na cadeia de cuidados. Há também um papel que cabe ao estado no âmbito das prioridades e da mobilização de recursos, sendo-lhe requerida a expressão do sentido de urgência para que esta mudança aconteça. Foram também identificadas oportunidades em diversas áreas, como na prevenção, no diagnóstico, na compliance medicamentosa, na terapêutica, na monitorização, no apoio à vida diária e na integração social. O que é necessário é que as soluções encontradas constituam respostas àquilo que são as verdadeiras necessidades dos intervenientes e não uma imposição tecnológica que só por si nada resolve. Do estudo resultou também a perceção de que há que (i) continuar a trabalhar no sentido de aproximar a comunidade científica, da clínica e do doente, (ii) fomentar a colaboração entre centros, com vista à criação de escala a nível global. Essa colaboração já parece acontecer a nível empresarial, tendo sido identificadas empresas Portuguesas com vocação global. A qualidade individual das instituições de ensino, dos centros de investigação, das empresas, permite criar as condições para que Portugal possa ser país um piloto e um case-study internacional em ALT, desde que para tal pudéssemos contar com um trabalho colaborativo entre instituições e com decisões políticas arrojadas.

Light-controlled resistive switching in laser-assisted annealed Ba0.8Sr0.2TiO3 thin films

In this work, Ba0.8Sr0.2TiO3 (BST)/ITO structures were grown on glass substrate and laser assisted annealing (LAA) was performed to promote the crystallization of BST. Atomic force microscopy and X-ray diffraction studies confirm the crack free and polycrystalline perovskite phase of BST. White light controlled resistive switching (RS) effect in Au/BST/ITO device is investigated. The device displays the electroforming-free bipolar RS characteristics and are explained by the modulationof the width and height of barrier at the BST/ITO interface via ferroelectric polarization. Moreover, the RS effect is signifi- cantly improved under white light illumination compared to that in the dark. The enhanced RS and photovoltaic effects are explained by considering depolarization field and charge distribution at the interface. The devices exhibit stable retention characteristics with low currents (mA), which make them attractive for non volatile memory devices.

The category 'natural' in the discourse of couples who used medically assisted procreation

As a constantly evolving set of complex biotechnologies, medically assisted procreation (MAP) jeopardises a category that seems to be taken for granted: that of 'natural'. What is 'natural' or not when MAP is used to procreate? What are the boundaries between a 'natural' and a 'non-natural' fertilisation? Drawing upon a dialogical approach to language and cognition, our study examined the semantic field of the category 'natural' as expressed in interviews between a psychiatrist and seven couples who resorted to MAP and had to decide whether to keep their frozen pre-embryonic cells (zygotes) for further procreation or to allow them be destroyed. We examined how these couples evoked the category 'natural' and showed that in their argumentation, the category 'natural' encompassed a wide variety of phenomena, which shifted the boundaries between the 'natural' and 'non-natural'. In so doing, the couples 'renaturalised' MAP, normalized it, moved the boundaries between what is legitimate or not, and showed their accountability. Hence, reference to the category 'natural' seemed to act both as an argumentative and a psychological resource in the elaboration of the person's experience in resorting to MAP.

Dissociation of allocentric and egocentric orientation: Effect on hippocampal place cells and place navigation

Navigation by means of cognitive maps appears to require the hippocampus; hippocampal place cells (PCs) appear to store spatial memories because their discharge is confined to cell-specific places called firing fields (FFs). Experiments with rats manipulated idiothetic and landmark-related information to understand the relationship between PC activity and spatial rotation. Rotating a circular arena in the caused a discrepancy between these cuse. This discrepancy caused most FFs to disappear in both the arena and room reference frames. However, FFs persisted in the rotating arena frame when the discrepancy was reduced by darkness or by a card in the arena. The discrepancy was increased by "field clamping" the rat in a room-defined FF location by rotations that countered its locomotion. Most FFs disspared and reappeared an hour or more after the clamp. Place-avoidance experiments showed that navigation uses independent idiothetic and exteroceptive memories. Rats learned to avoid the unmarked footshock region within a circular arena. When acquired on the stable arena in the light, the location of the punishment was learned by using both room and idiothetic cues; extinction in the dark transferred to the following session in the light. If, however, extinction occured during rotation, only the arena-frame avoidance was extinguished in darkness; the room-defined location was avoided when the light were turned back on. Idiothetic memory of room-defined avoidance was not formed during rotation in light; regardless of rotation with a randomly dispersed pellet. The resulting behaviour alternated between random pellet searching and target-directed navigation, making it possible to examine PC correlates of these two classes of spatial behaviour. The independence of idiothetic and exteroceptive spatial memories and the disruption of PC firing during rotation suggest that PCs may not be necessary for spatial cognition; this idea can be tested by recording during place-avoidance and preference tasks.