Inelastic torsional seismic response of nominally symmetric reinforced concrete frame structures: shaking table tests

This paper discusses the torsional response of a scaled reinforced concrete frame structure subjected to several uniaxial shaking table tests. The tested structure is nominally symmetric in the direction of shaking and exhibits torsion attributable to non-uniform yielding of structural components and uncertainties in the building process. Asymmetric behavior is analyzed in terms of displacement, strain in reinforcing bars, energy dissipated at plastic hinges, and damage at section and frame levels. The results show that for low levels of seismic hazard, for which the structure is expected to perform basically within the elastic range, the accidental eccentricity is not a concern for the health of the structure, but it significantly increases the lateral displacement demand in the frames (about 30%) and this might cause significant damage to non-structural components. For high levels of seismic hazard the effects of accidental torsion become less important. These results underline the need to consider accidental eccentricity in evaluating the performance of a structure for very frequent or frequent earthquakes, and suggest that consideration of torsion may be neglected for performance levels associated with rare or very rare earthquakes.

The folded plate model in structural analysis. Elastic, plastic and dynamic formulations for nonprismatic structures

A specific numerical procedure for the analysis of arbitrary nonprismatic folded plate structures is presented. An elastic model is studied and compared with a harmonic solution for a prismatic structure. An extension to the plastic analysis is developed, and the influence of the structural geometry and loading pattern is analyzed. Nonprismatic practical cases, with arbitrary geometry and loading are shown, as well in the elastic range as in the plastic one. Finally, a dynamic formulation is outlined

Piezoelectric sensing and non-parametric statistical signal processing for health monitoring of hysteretic dampers used in seismic-resistant structures

The paper proposes a new application of non-parametric statistical processing of signals recorded from vibration tests for damage detection and evaluation on I-section steel segments. The steel segments investigated constitute the energy dissipating part of a new type of hysteretic damper that is used for passive control of buildings and civil engineering structures subjected to earthquake-type dynamic loadings. Two I-section steel segments with different levels of damage were instrumented with piezoceramic sensors and subjected to controlled white noise random vibrations. The signals recorded during the tests were processed using two non-parametric methods (the power spectral density method and the frequency response function method) that had never previously been applied to hysteretic dampers. The appropriateness of these methods for quantifying the level of damage on the I-shape steel segments is validated experimentally. Based on the results of the random vibrations, the paper proposes a new index that predicts the level of damage and the proximity of failure of the hysteretic damper

In situ damage detection in frame structures through coupled response measurements

Due to the existence of global modes and local modes of the neighbouring members, damage detection on a structure is more challenging than damage on isolated beams. Detection of an artificial circumferential crack on a joint in a frame-like welded structure is studied in this paper using coupled response measurements. Similarity to real engineering structures is maintained in the fabrication of the test frame. Both the chords and the branch members have hollow sections and the branch members have smaller sizes. The crack is created by a hacksaw on a joint where a branch meets the chord. The methodology is first demonstrated on a single hollow section beam. The test results are then presented for the damaged and undamaged frame. The existence of the damage is clearly observable from the experimental results. It is suggested that this approach offers the-potential to detect damage in welded structures such as cranes, mining equipment, steel-frame bridges, naval and offshore structures. (C) 2003 Elsevier Ltd. All rights reserved.

Crack detection in welded mechanical structures using coupled vibrations

Detection of a fatigue crack in a welded frame structure is studied in this paper using coupled response measurements. Similarity to real engineering structures is maintained in the fabrication of the test frame with hollow section chords and branch members. The fatigue crack was created by a special reciprocating mechanism that generates cyclic stress on a beam member of the structure. The methodology of coupled response measurements is first demonstrated on a single hollow section beam by analytical simulation and experimental validation. The issues of using this approach for fatigue crack detection in real structures are then examined. Finally, the experimental results of the frame under different scenarioes are presented. The existence of the crack is clearly observable from the FRF plots. It is suggested that this approach offers the potential to detect cracks in welded frame structures and is a useful tool for routine maintenance work and health assessment.

Reliability-based evaluation of design code provisions for circular concrete-filled steel columns

This paper presents an investigation of design code provisions for steel-concrete composite columns. The study covers the national building codes of United States, Canada and Brazil, and the transnational EUROCODE. The study is based on experimental results of 93 axially loaded concrete-filled tubular steel columns. This includes 36 unpublished, full scale experimental results by the authors and 57 results from the literature. The error of resistance models is determined by comparing experimental results for ultimate loads with code-predicted column resistances. Regression analysis is used to describe the variation of model error with column slenderness and to describe model uncertainty. The paper shows that Canadian and European codes are able to predict mean column resistance, since resistance models of these codes present detailed formulations for concrete confinement by a steel tube. ANSI/AISC and Brazilian codes have limited allowance for concrete confinement, and become very conservative for short columns. Reliability analysis is used to evaluate the safety level of code provisions. Reliability analysis includes model error and other random problem parameters like steel and concrete strengths, and dead and live loads. Design code provisions are evaluated in terms of sufficient and uniform reliability criteria. Results show that the four design codes studied provide uniform reliability, with the Canadian code being best in achieving this goal. This is a result of a well balanced code, both in terms of load combinations and resistance model. The European code is less successful in providing uniform reliability, a consequence of the partial factors used in load combinations. The paper also shows that reliability indexes of columns designed according to European code can be as low as 2.2, which is quite below target reliability levels of EUROCODE. (C) 2009 Elsevier Ltd. All rights reserved.

Analysis of the behavior of transverse walls of socket base connections

This paper presents a theoretical and experimental analysis of socket base connections of precast concrete structures with regard to the behavior of transverse walls. The experimental program included seven specimens, for which the type of interface in contact with cast-in-place concrete, the load eccentricities and the embedded lengths were all varied, A design model was proposed to calculate the reinforcements of the transverse walls. Based on the obtained results, some conclusions can be drawn: (a) The top of the transverse wall on the compression side of the smooth connections and the top of the two transverse walls of the rough connections are submitted to a bending-tension and this tension prevails on the bending; (b) The design model proposed for the calculation of the reinforcement of the transverse wall on the compression side provides the best prediction of the experimental results for all specimens when compared to the current design models; (c) For rough interfaces, the top of the transverse wall on the tension side is more requested than the top of transverse wall on the compression side; (d) The results of the proposed design model for the reinforcement of the transverse wall on the tension side of rough connections were in close agreement with the experimental results. (C) 2008 Elsevier Ltd. All rights reserved.

Parametrical study of masonry walls subjected to in-plane loading through numerical modeling

This paper deals with the numerical assessment of the influence of parameters such as pre-compression level, aspect ratio, vertical and horizontal reinforcement ratios and boundary conditions on the lateral strength of masonry walls under in-plane loading. The numerical study is performed through the software DIANA (R) based on the Finite Element Method. The validation of the numerical model is carried out from a database of available experimental results on masonry walls tested under cyclic lateral loading. Numerical results revealed that boundary conditions play a central role on the lateral behavior of masonry walls under in-plane loading and determine the influence of level of pre-compression as well as the reinforcement ratio on the wall strength. The lateral capacity of walls decreases with the increase of aspect ratio and with the decrease of pre-compression. Vertical steel bars appear to have almost no influence in the shear strength of masonry walls and horizontal reinforcement only increases the lateral strength of masonry walls if the shear response of the walls is determinant for failure, which is directly related to the boundary conditions. (C) 2011 Elsevier Ltd. All rights reserved.

Numerical modeling of ductile crack extension in high pressure pipelines with longitudinal flaws

This study examines the applicability of a micromechanics approach based upon the computational cell methodology incorporating the Gurson-Tvergaard (GT) model and the CTOA criterion to describe ductile crack extension of longitudinal crack-like defects in high pressure pipeline steels. A central focus is to gain additional insight into the effectiveness and limitations of both approaches to describe crack growth response and to predict the burst pressure for the tested cracked pipes. A verification study conducted on burst testing of large-diameter, precracked pipe specimens with varying crack depth to thickness ratio (a/t) shows the potential predictive capability of the cell approach even though both the CT model and the CTOA criterion appear to depend on defect geometry. Overall, the results presented here lend additional support for further developments in the cell methodology as a valid engineering tool for integrity assessments of pipelines with axial defects. (C) 2011 Elsevier Ltd. All rights reserved,

Métodos de estimativa de descarga sólida em rios : análise comparativa

Transporte de sedimentos em bacias hidrográficas está relacionado com geomorfologia, ecologia fluvial, estabilidade das estruturas de engenharia e condições de navegação, dentre outros aspectos importantes para o planejamento e o controle de recursos hídricos. Existência de inúmeras variáveis envolvidas na mecânica de transporte de sedimentos e complexidade nas interações de processos físicos tornam difícil o estabelecimento de metodologias indiretas para estimativa de transporte de sedimentos em rios. Desta forma, não existe ainda metodologia universalmente aceita. O principal objetivo do presente trabalho é a análise comparativa de diferentes métodos empíricos disponíveis na literatura para estimativa de descargas sólidas em rios, considerando suas características específicas e resultados de aplicações às bacias dos rios Santa Joana e Santa Maria do Doce e microbacias Sossego e Santa Júlia, inseridas na porção da bacia do rio Doce localizada no Espírito Santo. Foram aplicados os métodos de estimativa indireta de descarga sólida: Einstein Modificado por Colby e Hembree (1955); Colby Simplificado (1957); Engelund & Hansen (1967); Ackers & White (1973); Yang (1973), Karim (1998) e Cheng (2002). Considerando as médias das estimativas de descarga sólida de material de leito (Qsml) relativas às campanhas realizadas em período chuvoso para a seção transversal do rio Doce, de maior porte, o método de Karim (1998), seguido pelo método de Ackers & White (1973), apresentou o maior valor, enquanto que o método de Yang (1973) apresentou o menor. Para os rios Santa Maria do Doce e Santa Joana e os córregos Santa Júlia e Sossego, verificou-se que o método de Ackers & White (1973), seguido de Karim (1998) e Yang (1973) apresentaram as maiores médias, enquanto que os métodos de Cheng (2002) e Engelund & Hansen (1967) apresentaram as menores. O método Simplificado de Colby apresentou as maiores estimativas de descargas sólidas totais (Qst) para todas as seções transversais de todos os cursos d'água monitorados. Concluiu-se que os diferentes métodos indiretos podem resultar em grandes diferenças em estimativas de transporte de sedimento em rios e que, desta forma, resultados de aplicação destes métodos devem ser considerados com muita cautela. Os resultados mostraram a grande importância de realização de campanhas de medição sedimentométricas para avaliação do transporte de sedimentos e definição dos melhores métodos indiretos de estimativa para cursos d'água específicos.

Projecto de execução de fundações e estruturas de uma ponte em betão armado pré-esforçado

Este Trabalho refere-se ao Projecto de Execução de Fundações e Estruturas de uma Ponte Rodoviária em betão armado pré-esforçado, realizado no âmbito do Trabalho Final de Mestrado em Engenharia Civil – Especialização em Estruturas, do Instituto Superior de Engenharia de Lisboa. O Projecto de Execução é composto de Peças Escritas e Peças Desenhadas. Nas Peças Escritas estão incluídos: Memória Justificativa e Descritiva; Cálculos Justificativos e Anexos. A ponte é composta por dois tabuleiros paralelos com 10,28m de largura cada um e afastados entre si de 0,10m. A obra é constituída de 8 tramos; os tramos correntes com 31m de comprimento e os tramos extremos com 25 e 20m de comprimento, perfazendo um comprimento total de 231m. A obra foi parcialmente isolada dos sismos pela introdução, em todos os pilares, de aparelhos de apoio de elevado amortecimento sísmico do tipo HDRB (High Damping Rubber Bearings). Encontram-se particularmente discriminadas e detalhadas neste projecto as seguintes situações: - Cálculo do Pré-esforço e respectivas perdas; - Acção das sobrecargas rodoviárias; - Diferença de comportamento da obra na entrada em serviço e no longo prazo; - Análise sísmica e do isolamento sísmico; - Estudo dos efeitos diferidos: retracção e fluência. Tendo as abordagens de cálculo e as verificações de segurança seguido a regulamentação nacional em vigor, nomeadamente RSA e REBAP, foi no entanto feita uma aproximação às regras do “Capacity Design” previstas no EC8, em que se privilegia a actuação do projectista sobre o comportamento da estrutura, procurando uma resposta não linear da mesma, visando garantir que: - A rotura não ocorrerá nos elementos de fundação; - Nos pilares a dissipação de energia se faz através de rótulas plásticas, evitando-se roturas associadas a esforços transversos. A aplicação destas regras neste Projecto demonstrou haver um agravamento substancial na definição dos esforços a que devem resistir alguns dos componentes da estrutura, designadamente os pilares e as fundações, originando soluções de secções de betão e armaduras bem mais exigentes do que aqueles que resultariam da simples verificação de segurança, pela comparação entre esforços actuante e esforços resistentes “secção a secção”, imposta pela actual regulamentação nacional.

Seismic resistance of earth construction in Portugal

This paper presents an assessment of the potential seismic performance of new earth construction in Portugal. Results of a parametric study on a properly designed rammed earth construction, considering several strengthening solutions, are presented and discussed. It is concluded that single storey houses can have acceptable seismic performance even in high seismicity areas, provided that the structure is adequately strengthened by reinforced concrete columns and beams. Improvement of the characteristics of the structural material (earth) may be necessary to reduce damage.

Direcção de obra – obras de arte auto-estrada Transmontana – área 3

Este relatório diz respeito ao trabalho desenvolvido em ambiente de estágio académico numa Empreitada compreendendo Obras de Arte Correntes e Obras de Arte Especiais inseridas em traçado actual do IP4 que está a ser transformado em Auto-Estrada. As Obras de Arte Correntes compreendem Passagens Superiores, Passagens Inferiores e Passagens superiores de Nó. As Obras de Arte Especiais compreendem duas Pontes com vãos distintos. Todas as Obras de Arte referidas neste relatório contemplam uma solução mista de betão armado “in situ” e tabuleiros com vigas e pré-lajes em betão pré-fabricado. Além da descrição de todas as actividades realizadas em betão armado “in situ”, desde as fundações até ao tabuleiro, descreve também a execução dos diversos tipos de trabalhos de acabamentos. Além das actividades de construção civil, é efectuada uma descrição das actividades a cujo processo de realização estão associados trabalhos de concepção e desenvolvimento, como é o caso dos cimbres. Este relatório faz uma descrição abrangente das funções da Direcção de Obra numa Empreitada de Obras de Arte, que para além da execução da obra, com todas as actividades que lhe são inerentes, compreende várias áreas funcionais que fazem parte de uma empresa de construção civil, como a área comercial, financeira, planeamento, aprovisionamento, controlo orçamental, gestão contratual, gestão de subempreitadas e gestão da qualidade, ambiente e segurança.

Geotecnia urbana da zona ribeirinha de Vila Nova de Gaia (Cais de Gaia, Santa Marinha – Lavadores, Canidelo): uma avaliação preliminar

Mestrado em Engenharia Geotécnica e Geoambiente

Avaliação em tempo real de forças em cabos

Dissertação elaborada para a obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Estruturas