Um novo conceito de monitoramento e comunicação ambiental: a rede européia para a avaliação da qualidade do ar usando plantas bioindicadoras (EuroBionet)

Apesar de todo o progresso alcançado na redução da emissão de poluentes atmosféricos durante as últimas décadas, a poluição do ar ainda representa um dos principais problemas ambientais nos centros urbanos da Europa. Plantas bioindicadoras têm um papel cada vez maior no controle da qualidade do ar, já que seu uso comprova e demonstra os efeitos negativos da poluição em seres vivos de uma maneira facilmente inteligível, inclusive para leigos. Em uma rede de municípios, o projeto pan-europeu EuroBionet utiliza plantas bioindicadoras para a avaliação de possíveis efeitos da poluição aérea. Através de um conceito de comunicação específico, os resultados científicos do projeto são traduzidos e divulgados de uma forma que chama a atenção do público em geral e que sensibiliza a população urbana. Desta forma, pretende-se induzir a uma mudança no comportamento e aumentar a aceitação de medidas corretivas. No presente trabalho, os objetivos científicos e de comunicação do projeto EuroBionet são apresentados. Os primeiros resultados da exposição de plantas de tabaco em dez cidades européias, durante os meses de agosto e setembro de 2000, demonstram um gradiente de impacto de ozônio do norte para o sul e centro da Europa, com efeitos leves na Escócia e Dinamarca e fortes nas plantas expostas na Itália, França, Áustria e sul da Alemanha.

Projeto de um protótipo de um veículo elétrico

Os veículos movidos com combustíveis fósseis são, hoje em dia, os veículos mais utilizados em transportes. Estes meios de transporte caracterizam-se pelo seu baixo rendimento e por serem poluentes, pelo que, nos últimos anos, tem havido um esforço em criar ou melhorar meios de transporte, através do aumento do seu rendimento e eliminando a emissão de poluentes. A utilização de máquinas elétricas como meio de locomoção é uma das soluções alternativas, uma vez que, estas apresentam um rendimento elevado e não emitem diretamente gases tóxicos, apesar das baterias serem uma das principais dificuldades, no que diz respeito à relação peso/densidade de energia. Por outro lado, as baterias, devido à sua capacidade de armazenamento de energia, podem ser utilizadas para armazenar energia da rede elétrica, contribuindo para uma melhor gestão, e também para armazenar num veículo elétrico a energia gerada em modo de travagem e que posteriormente pode ser utilizada para fazer mover o motor elétrico. Neste trabalho fez-se um projeto de um veículo elétrico (VE) e estudou-se o impacto da utilização em massa de veículos elétricos na gestão da rede de energia elétrica. A verificação experimental fez-se com um conversor DC/DC bidirecional com uma configuração em ponte H e com um conversor DC/DC redutor unidirecional. Utilizaram-se compensadores clássicos para, em malha fechada, regular o binário, a velocidade e a corrente, através de compensadores Proporcional Integrativo (PI) e Proporcional Integrativo Derivativo (PID). No desenvolvimento deste projeto, fez-se uma análise teórica, realizaram-se simulações na ferramenta MATLAB/Simulink onde foram criados modelos do veículo elétrico para verificar o seu comportamento, e seguidamente analisaram-se experimentalmente estes resultados. O controlo deste veículo foi feito com a utilização de microcontroladores de baixo custo, recorrendo a uma arquitetura de processamento distribuído/partilhado, constituindo esse estudo uma nova contribuição. Os resultados demonstraram que o rendimento dos veículos elétricos em média encontram-se nos 85-90 %, superior aos atuais 40% dos veículos a combustão interna, eliminando também a emissão de poluentes.

Estudo térmico dos resíduos gerados da destilação atmosférica das misturas diesel/biodiesel de dendê

The growing world demand for energy supplied by fossil fuels, a major contributor to the emission of pollutants into the atmosphere and causing environmental problems, has been encouraging governments and international organizations to reflect and encourage the use of alternative renewable sources. Among these new possibilities deserves attention biodiesel, fuel cleaner and easy to reproduce. The study of new technologies involving that source is necessary. From this context, the paper aims at analyzing the thermal stability by thermogravimetric analysis, of the waste generated from atmospheric distillation of mixtures with ratios of 5, 10, 15 and 20% palm biodiesel in diesel with and without addition of BHT antioxidant. It was synthesized biodiesel through palm oil, via homogeneous catalysis in the presence of KOH, with and without the use of BHT and subsequently added to the diesel common indoor type (S1800) from a gas station BR. The diesel was already added with 5% biodiesel, and thus the proportions used for these blends were subtracted from the existing ratio in diesel fuel, resulting in the following proportions palm oil biodiesel: 0% (B5), 5% (B10), 10 % (B15) and 15% (B20). From atmospheric distillation analysis, performed in mixtures with and without BHT were collected residue generated by each sample and performed a thermal study from the thermogravimetric analysis at a heating rate of 10 °C.min-1, nitrogen atmosphere and heating to 600 ° C. According to the specifications of Resolution No. 7/2008 for biodiesel, it was found that the material was synthesized in accordance with the specifications. For mixtures, it was noted that the samples were in accordance with the ANP Resolution No. 42/2009. Given the TG / DTG curves of the samples of waste mixtures with and without BHT antioxidant was able to observe that they showed a single stage of thermal decomposition attributed to decomposition of heavy hydrocarbons and esters and other heavier constituents of the waste sample weighed. The thermal behavior of residues from atmospheric distillation of mixtures of diesel / biodiesel is very important to understand how this affects the proper functioning of the engine. A large amount of waste can generate a high content of particulate material, coke formation and carbonaceous deposits in engine valves, compromising their performance

Desenvolvimento de metodologia para avaliação de desempenho ambiental em edifícios adaptada à realidade do Nordeste brasileiro

This research refers to the production of green buildings, defined, mainly, based on the use of sources of alternative energies, smaller emission of pollutant, use of recyclable materials, systems of recycling of the waters, maximization of the natural illumination, preservation of green areas or native, and appropriate quality of the internal air. From the conception of those buildings, it appears the needs of evaluating them, creating the methodologies for the evaluation of environmental performance of buildings. In that way, this work can be divided in two moments: the first one when it identifies the methodologies for the evaluation of environmental performance for buildings existents in the literature, defining their categories, criteria and sub-criteria to be appropriate to the reality of the Brazilian Northeast; and the second one when starting from the analysis of the systems of existent evaluation. It defines a methodological base and it generates a new evaluation system, denominated MEDACNE (Methodology of Evaluation of Environmental Acting for Construction in the Northeast). In that moment, the process of framing of the section of the building site is verified under the maintainable optics, stimulated mainly by the pressures of the society - conferences, protocols and agreements. Finally, the proposed methodology was applied in a case study, a residential building, called Maria José Gurgel , located in Natal-RN, Brazil, for its validation. This methodological proposition should increase the patterns environmental places for the production of new buildings, and it will be a reference guide for architects, engineers and planners to develop their constructions considering the criteria of the sustainability. This study made use of bibliographical research in books and specialized magazines and the analysis of the data was realized in an interpretative way

Produção de metano entérico em pastagens tropicais

Na presente revisão, buscou-se apresentar os principais impactos ambientais causados pela pecuária, sobretudo, em relação às emissões de gases efeito estufa (GEE). Além disso, buscou-se apresentar possíveis formas de mitigar essas externalidades. A criação de bovinos, no Brasil, acontece de forma extensiva, muitas vezes em áreas com pastagem degradada e, portanto, de baixa produtividade. Isso possibilita à atividade uma oportunidade de redução do impacto causado ao meio ambiente, uma vez que ações tomadas, no sentido de melhorar o rendimento animal, devem resultar em um menor consumo de recursos naturais (terra e água) e maior eficiência do sistema digestivo animal. Os principais problemas apontados pelos pesquisadores, no que tange à pecuária extensiva, são o metano emitido pela fermentação entérica dos ruminantes, o óxido nitroso emitido pelos dejetos dos animais em pastejo e o dióxido de carbono trocado pelo solo e vegetação. Muitos fatores influenciam a produção de CH4 entérico dos ruminantes, inclusive o tipo de carboidrato fermentado, o sistema digestivo do animal, a quantidade e o tipo de alimentos consumidos. Diante do exposto, pesquisadores têm desenvolvido tecnologias para reduzir a emissão de metano, através da melhoria das práticas de manejo alimentar, manipulação ruminal, por meio de suplementação com monensina, lipídios, ácidos orgânicos e compostos de plantas. Outras estratégias de redução de metano que foram investigadas são: defaunação e vacinas, que buscam inibir micro-organismos metanogênicos e a metanogênese. Assim, a busca por sistemas de produção eficientes tem sido uma das perspectivas da pecuária mundial para reduzir a emissão de poluentes e intensificar a produção animal.

Análise estatística das emissões de CO e HC produzidas por gases da exaustão veicular oriundos de gasolina, GNV e mistura álcool/gasolina

The vehicles are the main mobile sources of carbon monoxide (CO) and unburned hydrocarbons (HC) released into the atmosphere. In the last years the increment of the fleet of vehicles in the municipal district of Natal-RN it is contributing to the increase of the emissions of those pollutants. The study consisted of a statistical analysis of the emissions of CO and HC of a composed sample for 384 vehicles with mechanization Gasoline/CNG or Alcohol/Gasoline/CNG of the municipal district of Natal-RN. The tests were accomplished in vehicles submitted to Vehicular Safety's Inspection, in the facilities of INSPETRANS, Organism of Vehicular Inspection. An partial gases analyzer allowed to measure, for each vehicle, the levels of CO and HC in two conditions of rotation of the motor (900 and 2500 rpm). The statistical analysis accomplished through the STATISTICA software revealed a sensitive reduction in the efficiency of the converters catalytic after 6 years of use with emission average it is of 0,78% of CO and 156 (ppm) of HC, Which represents approximately 4 (four) times the amount of CO and the double of HC in comparison with the newest vehicles. The result of a Student s t-test, suggests strongly that the average of the emissions of HC (152 ppm), at 900 rpm, is 40% larger than at 2500 rpm, for the motor without load. This result reveals that the efficiency of the catalytic conversion is limited kinetically in low engine speeds. The Study also ends that when comparing the emissions of CO and HC considering the influence of the fuels, it was verified that although the emissions of CO starting from CNG are 62% smaller than arising from the gasoline, there are not significant differences among the emissions of HC originating from of CNG and of the gasoline. In synthesis, the results place the current criteria of vehicular inspection, for exhaust gases, in doubt, leading the creation of emission limits of pollutant more rigorous, because the efficiency of the converters catalytic is sensibly reduced starting from 6 years of use. It is also raised the possibility of modifications in the test conditions adopted by the current norms, specifically in the speed engine, have seen that in the condition without load the largest emission indexes were registered in slow march. That fact that allows to suggest the dismissal of the tests in high speed engine, reducing the time of inspection in half and generating economy of fuel

Análise preditiva a partir da caracterização das emissões gasosas e do óleo lubrificante em frotas com motorização a diesel

This work was motivated by the importance of conducting a study of vehicle emissions in captive fleets with diesel engine, coupled with the predictive maintenance plan. This type of maintenance includes techniques designed to meet the growing market demand to reduce maintenance costs by increasing the reliability of diagnoses, which has increased interest in automated predictive maintenance on diesel engines, preventing problems that might evolve into routine turn into serious situations, solved only with complex and costly repairs, the Reliability Centered Maintenance, will be the methodology that will make our goal is reached, beyond maintaining the vehicles regulated as fuel consumption and emissions. To Therefore, technical improvements were estimated capable of penetrating the automotive market and give the inshore fleet emission rates of opacity of the vehicles, being directly related to the conditions of the lubricating oil thus contributing to reducing maintenance costs by contributing significantly to emissions of pollutants and an improvement in the air in large cities. This criterion was adopted and implemented, em 241 buses and produced a diagnosis of possible failures by the correlation between the characterization of used lubricating oils and the analysis of opacity, with the objective of the aid the detection and solution of failures for the maintenance of sub-systems according to design criteria, and for this to be a deductive methodology to determine potential causes of failures, has been automated to implement a predictive maintenance system for this purpose was used in our study a mobile unit equipped with a opacimeter and a kit for collection and analysis of lubricating oil and the construction of the network diagnostics, we used a computer program in Microsoft Office Access 2007 platform tool is indispensable for creating a database data, this method is being used and successfully implemented in seven (7) bus companies from the city of Natal (RN) Brazil

Análise de desempenho de um fogão solar com parabola fabricada em material compósito

It is presented a solar cooker made with a parabolic reflector composed by a composite material. For this purpose, it was utilized a cast concrete with a parabolic profile obtained by means of modeling. It will be demonstrated the manufacturing process and settings, as well as tests results, in order to determine the contact temperature and cooking time of some foods. This solar cooker presents the following main characteristics: the concentration method, low cost and easy manufacturing process. It was performed by employing recycled materials such as cement, plaster, crushed polystyrene and wheels. The captation area measures 1 square meter and its parabole was covered with a mirrors measuring 25 cm2. A temperature higher than 650°C was obtained. Furthermore, it has been demonstrated that the cooking viability for several type of foods such as beans, potatoes, rice, yams and pasta can be used in two meals for a family of four. In addition, the advantages of this cooker were analysed in comparison with others described in literature as well as those operating on gas. Especially in Northeast of Brazil, where there is a potential for solar energy, this prototype is an important tool, because it avoids not only desertification, but also pollutants from burning firewoods which cause ecological imbalance

Novas alternativas de remoção de enxofre do óleo diesel utilizando tensoativos e microemulsões

The diesel combustion form sulfur oxides that can be discharged into the atmosphere as particulates and primary pollutants, SO2and SO3, causing great damage to the environment and to human health. These products can be transformed into acids in the combustion chamber, causing damage to the engines. The worldwide concern with a clean and healthy environment has led to more restrictive laws and regulations regulating the emission levels of pollutants in the air, establishing sulfur levels increasingly low on fuels. The conventional methods for sulfur removal from diesel are expensive and do not produce a zero-level sulfur fuel. This work aims to develop new methods of removing sulfur from commercial diesel using surfactants and microemulsion systems. Its main purpose is to create new technologies and add economic viability to the process. First, a preliminary study using as extracting agent a Winsor I microemulsion system with dodecyl ammonium chloride (DDACl) and nonyl phenol ethoxylated (RNX95) as surfactant was performed to choose the surfactant. The RNX95 was chosen to be used as surfactant in microemulsioned systems for adsorbent surface modification and as an extracting agent in liquid-liquid extraction. Vermiculite was evaluated as adsorbent. The microemulsion systems applied for vermiculite surface modification were composed by RNX95 (surfactant), n-butanol (cosurfactant), n-hexane (oil phase), and different aqueous phases, including: distilled water (aqueous phase),20ppm CaCl2solution, and 1500ppm CaCl2solution. Batch and column adsorption tests were carried out to estimate the ability of vermiculite to adsorb sulfur from diesel. It was used in the experiments a commercial diesel fuel with 1,233ppm initial sulfur concentration. The batch experiments were performed according to a factorial design (23). Two experimental sets were accomplished: the first one applying 1:2 vermiculite to diesel ratio and the second one using 1:5 vermiculite to diesel ratio. It was evaluated the effects of temperature (25°C and 60°C), concentration of CaCl2in the aqueous phase (20ppm and 1500ppm), and vermiculite granule size (65 and 100 mesh). The experimental response was the ability of vermiculite to adsorb sulfur. The best results for both 1:5 and 1:2 ratios were obtained using 60°C, 1500ppm CaCl2solution, and 65 mesh. The best adsorption capacities for 1:5 ratio and for 1:2 ratio were 4.24 mg sulfur/g adsorbent and 2.87 mg sulfur/g adsorbent, respectively. It was verified that the most significant factor was the concentration of the CaCl2 solution. Liquid-liquid extraction experiments were performed in two and six steps using the same surfactant to diesel ratio. It was obtained 46.8% sulfur removal in two-step experiment and 73.15% in six-step one. An alternative study, for comparison purposes, was made using bentonite and diatomite asadsorbents. The batch experiments were done using microemulsion systems with the same aqueous phases evaluated in vermiculite study and also 20ppm and 1500 ppm BaCl2 solutions. For bentonite, the best adsorption capacity was 7.53mg sulfur/g adsorbent with distilled water as aqueous phase of the microemulsion system and for diatomite the best result was 17.04 mg sulfur/g adsorbent using a 20ppm CaCl2solution. The accomplishment of this study allowed us to conclude that, among the alternatives tested, the adsorption process using adsorbents modified by microemulsion systems was considered the best process for sulfur removal from diesel fuel. The optimization and scale upof the process constitutes a viable alternative to achieve the needs of the market

Craqueamento termocatalítico de óleo de girassol na presença da peneira molecular SAPO-5

The catalytic cracking of triglycerides presents itself as a possible alternative to the production of biofuels with low emission of pollutants. In this work were synthesized the SAPO-5, the catalysts for the cracking reaction of soybean oil is presented. The solids were powder X-ray diffraction (XRD), thermogravimetric analysis (TG/DTG) and infrared spectroscopy (FTIR). The analyses indicated that the synthesis method has employed to obtain materials with high surface area and high acid. The soybean oil thermal and thermal catalytic cracking, realized from the room temperature to 450 ºC in a simple distillation system, has allowed obtaining two liquid fractions, each consisting of two phases, one aqueous and another organic, organic liquid (OL). The OL obtained from first fractions has shown high acid index, even in the thermal catalytic process. The products obtained in the cracking of soybean oil were analyzed by distillation, acid number, infra-red spectroscopy, density, viscosity, carbon residue, cetane number determination and characterization. The analysis of the products obtained in the presence and in the absence of the SAPO-5 permitted to conclude that all the solids tested presented catalytic activity in the deoxygenation of final products only at the second step of the cracking process

The Chemical Percolation Devolatilization Model Applied to the Devolatilization of Coal in High Intensity Acoustic Fields

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Investigação e aplicação de métodos primal - dual pontos interiores em problemas de despacho econômico e ambiental

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Método previsor-corretor primal-dual de pontos interiores em problemas multiobjetivo de despacho econômico e ambiental

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influências do protocolo agroambiental do setor sucroalcooleiro na produção de açúcar, álcool e energia: estudo de caso em uma usina no interior do Estado de São Paulo

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Metodologia para avaliação de desempenho ambiental em aeroportos e sua aplicação no Aeroporto Internacional de Viracopos, Campinas (SP)

Pós-graduação em Geologia Regional - IGCE