Métodos geofísicos aplicados ao ultramafito da Serra de Quatipuru - Estado do Pará

O objetivo deste trabalho foi a aplicação de métodos geofísicos para a avaliação econômica de ocorrência de níquel, cromo e amianto, em uma área de 6,25 km² - Malha 2 - Serra de Quatipuru, localizada a cerca de 50 km a SW de Conceição do Araguaia, no sul do Estado do Pará. Inicialmente foi aplicado o método magnético em caráter de reconhecimento, usando magnetômetros de campo total e componente vertical visando localizar zonas anômalas de amianto e cromita, uma vez que estes minerais se encontram associados com a magnetita. Em seguida foi usado o método eletromagnético de "dip angle" com o objetivo de definir zonas condutoras associadas a possíveis depósitos minerais ou características estruturais. Com base na interpretação destes dois métodos, definiu-se os locais de aplicação do método de polarização elétrica induzida-resistividade, que teve caráter de detalhe visando como alvo principal depósitos de sulfetos disseminados. As possíveis ocorrências minerais na área foram correlacionadas com anomalias geofísicas e confirmadas através de testemunhos de sondagem concluindo-se não serem de importância econômica. Contudo a aplicação destes métodos geofísicos foi útil, pois possibilitou o levantamento detalhado da área, que de outra forma só poderia ser realizado por meio dos métodos mais convencionais, tais como sondagem mecânica através de perfurações, os quais são muito caros e demorados.

Desempenho, qualidade de carcaça e da carne de cordeiros alimentados com dietas contendo silagens de milho consorciadas ou não com capins tropicais

Pós-graduação em Ciência e Tecnologia Animal - FEIS

Análise do circuito de água de refrigeração de uma unidade de regeneração de solventes

A EGEO Solventes S.A. é uma empresa com atividade na área da gestão de resíduos, focando-se na regeneração de solventes. Na unidade industrial da empresa recorre-se à destilação de misturas de solventes usados para obtenção do solvente regenerado. Esta operação exige água para o arrefecimento e condensação dos destilados das misturas de solventes, que, posteriormente, é arrefecida em torres de refrigeração instaladas na unidade. Durante o tempo de operação da unidade foram identificados problemas na condensação dos solventes limpos, obrigando a que se ligassem dois condensadores em série para assegurar a condensação do vapor produzido na destilação e à necessidade de caudais maiores de utilidade fria. Outro dos problemas identificados foi a baixa eficiência das torres de refrigeração, uma vez que a diferença de temperaturas da água à entrada e à saída do equipamento é muito baixa. Assim sendo, o objetivo principal deste trabalho é identificar as principais causas para a baixa eficiência dos equipamentos e propor alterações aos equipamentos ou soluções de melhoria do processo. Para diagnosticar estes problemas foram recolhidas amostras para determinação da composição do solvente limpo obtido e registadas as condições de operação para obtenção da mistura ECOSOLVE MET. Recorrendo a metodologias de projeto determinou-se o fator de resistência do fouling no condensador C1 e seguidamente a geometria, a alocação de correntes e a orientação do condensador mais adequadas e concluiu-se que este está sujeito a uma forte acumulação de material nas paredes e que a melhor opção seria recorrer a um permutador horizontal com condensação na carcaça, mas aumentando o número de passagens da água nos tubos. No que diz respeito à operação da torre de arrefecimento, determinou-se o caudal mínimo de ar para determinadas condições de operação e verificou-se que o caudal de ar alimentado à torre era superior ao mínimo determinado. Foram observadas diferenças quando comparadas as condições de operação experimentais com a performance da unidade usando oito enchimentos estruturados e aleatórios para os quais há dados na literatura São também apresentadas alternativas de operação e o projeto de uma torre de arrefecimento de água, sustentada numa análise económica de todo o processo. As simulações foram realizadas com recurso ao AspenPlus®.

Gestão Técnica Centralizada em Edifícios da Força Aérea

A investigação centra-se na aplicação da Gestão Técnica Centralizada como instrumento para a melhoria da eficiência energética dos edifícios e infraestruturas da Força Aérea Portuguesa e diminuição de pessoal afeto à sua manutenção, tendo por base, dois casos de estudo, o edifício QC12 do Centro de Formação Militar e Técnica da Força Aérea e o ECOTERMOLAB, pertencente ao Instituto de Soldadura e Qualidade. Da análise desenvolvida conclui-se que o funcionamento dos edifícios ECOTERMOLAB e QC12, com controlo por GTC, representam anualmente uma diminuição de consumo energético em 30% e 44% respetivamente e, uma redução de 50% nos recursos humanos afetos à instalação do QC12. Da viabilidade económica obtiveram-se as métricas de Valor Atual Líquido e a Taxa Interna de Rentabilidade positivos e um Período de Recuperação do Investimento, de 11,5 anos para ECOTERMOLAB e 10,7 anos para QC12. Por fim, teceram-se algumas recomendações, dirigidas à Força Aérea Portuguesa, com o intento de melhorar a eficiência energética elétrica e a redução de recursos humanos afetos. Abstract: The research is focused in the application of the Centered Technique Management as an instrument to improve the Portuguese Air Force buildings and infrastructures’ energetic efficiency and to reduce the staff in charge of its maintenance, based on two study cases, QC 12 building in The Air Force Military and Technique Training Center and ECOTERMOLAB, which belongs to Instituto de Soldadura e Qualidade (Quality and Welding Institute). From the analysis, one can conclude that the functioning of the ECOTERMOLAB and QC12 buildings, with GTC control, represents an annual consumption of less 30% and 44% respectively and a 50% reduction in the human resources of the QC 12. From the economical viability, it was possible to get the figures of the Net Present Value and the Internal Rate of Return and a Period of Return on Investment of 11,5 years for ECOTERMOLAB and 10,7 years for QC 12. Finally, some recommendations to the Portuguese Air Force were made, aiming the improvement of the electrical energetic efficiency and a reduction in human resources.

The significant role of third-party logistics (3pl) operators as fosterers of organizational performance in colombian companies

La eliminación de barreras entre países es una consecuencia que llega con la globalización y con los acuerdos de TLC firmados en los últimos años. Esto implica un crecimiento significativo del comercio exterior, lo cual se ve reflejado en un aumento de la complejidad de la cadena de suministro de las empresas. Debido a lo anterior, se hace necesaria la búsqueda de alternativas para obtener altos niveles de productividad y competitividad dentro de las empresas en Colombia, ya que el entorno se ha vuelto cada vez más complejo, saturado de competencia no sólo nacional, sino también internacional. Para mantenerse en una posición competitiva favorable, las compañías deben enfocarse en las actividades que le agregan valor a su negocio, por lo cual una de las alternativas que se están adoptando hoy en día es la tercerización de funciones logísticas a empresas especializadas en el manejo de estos servicios. Tales empresas son los Proveedores de servicios logísticos (LSP), quienes actúan como agentes externos a la organización al gestionar, controlar y proporcionar actividades logísticas en nombre de un contratante. Las actividades realizadas pueden incluir todas o parte de las actividades logísticas, pero como mínimo la gestión y ejecución del transporte y almacenamiento deben estar incluidos (Berglund, 2000). El propósito del documento es analizar el papel de los Operadores Logísticos de Tercer nivel (3PL) como promotores del desempeño organizacional en las empresas colombianas, con el fin de informar a las MIPYMES acerca de los beneficios que se obtienen al trabajar con LSP como un medio para mejorar la posición competitiva del país.

Design of an Efficient Hybrid System for Electricity Production with Supervisory Control

This chapter aims to develop a new method for the economical evaluation of Hybrid Systems for electricity production. The different types of renewable sources are specifically evaluated in the economical performance of the overall equipment. The presented methodology was applied to evaluate the design of a photovoltaic-wind-diesel hybrid system to produce electricity for a community in the neighbourhood of Luanda, Angola. Once the hybrid generator is selected, it is proposed to provide the system with a supervisory control strategy to maximize its operating efficiency.

Performance load testing and structural adequacy evaluation of road bridge decks

Many ageing road bridges, particularly timber bridges, require urgent improvement due to the demand imposed by the recent version of the Australian bridge loading code, AS 5100. As traffic volume plays a key role in the decision of budget allocations for bridge refurbishment/ replacement, many bridges in low volume traffic network remain in poor condition with axle load and/ or speed restrictions, thus disadvantaging many rural communities. This thesis examines an economical and environmentally sensible option of incorporating disused flat rail wagons (FRW) in the construction of bridges in low volume, high axle load road network. The constructability, economy and structural adequacy of the FRW road bridge is reported in the thesis with particular focus of a demonstration bridge commissioned in regional Queensland. The demonstration bridge comprises of a reinforced concrete slab (RCS) pavement resting on two FRWs with custom designed connection brackets at regular intervals along the span of the bridge. The FRW-RC bridge deck assembly is supported on elastomeric rubber pads resting on the abutment. As this type of bridge replacement technology is new and its structural design is not covered in the design standards, the in-service structural performance of the FRW bridge subjected to the high axle loadings prescribed in AS 5100 is examined through performance load testing. Both the static and the moving load tests are carried out using a fully laden commonly available three-axle tandem truck. The bridge deck is extensively strain gauged and displacement at several key locations is measured using linear variable displacement transducers (LVDTs). A high speed camera is used in the performance test and the digital image data are analysed using proprietary software to capture the locations of the wheel positions on the bridge span accurately. The wheel location is thus synchronised with the displacement and strain time series to infer the structural response of the FRW bridge. Field test data are used to calibrate a grillage model, developed for further analysis of the FRW bridge to various sets of high axle loads stipulated in the bridge design standard. Bridge behaviour predicted by the grillage model has exemplified that the live load stresses of the FRW bridge is significantly lower than the yield strength of steel and the deflections are well below the serviceability limit state set out in AS 5100. Based on the results reported in this thesis, it is concluded that the disused FRWs are competent to resist high axle loading prescribed in AS 5100 and are a viable alternative structural solution of bridge deck in the context of the low volume road networks.

A simulation framework for smart meter security evaluation

The evolution of classic power grids to smart grids creates chances for most participants in the energy sector. Customers can save money by reducing energy consumption, energy providers can better predict energy demand and environment benefits since lower energy consumption implies lower energy production including a decrease of emissions from plants. But information and communication systems supporting smart grids can also be subject to classical or new network attacks. Attacks can result in serious damage such as harming privacy of customers, creating economical loss and even disturb the power supply/demand balance of large regions and countries. In this paper, we give an overview about the German smart measuring architecture, protocols and security. Afterwards, we present a simulation framework which enables researchers to analyze security aspects of smart measuring scenarios.

Evaluation of k-epsilon and RNG turbulence models for confined swirling and non-swirling flow

In a very recent study [1] the Renormalisation Group (RNG) turbulence model was used to obtain flow predictions in a strongly swirling quarl burner, and was found to perform well in predicting certain features that are not well captured using less sophisticated models of turbulence. The implication is that the RNG approach should provide an economical and reliable tool for the prediction of swirling flows in combustor and furnace geometries commonly encountered in technological applications. To test this hypothesis the present work considers flow in a model furnace for which experimental data is available [2]. The essential features of the flow which differentiate it from the previous study [1] are that the annular air jet entry is relatively narrow and the base wall of the cylindrical furnace is at 90 degrees to the inlet pipe. For swirl numbers of order 1 the resulting flow is highly complex with significant inner and outer recirculation regions. The RNG and standard k-epsilon models are used to model the flow for both swirling and non-swirling entry jets and the results compared with experimental data [2]. Near wall viscous effects are accounted for in both models via the standard wall function formulation [3]. For the RNG model, additional computations with grid placement extending well inside the near wall viscous-affected sublayer are performed in order to assess the low Reynolds number capabilities of the model.

Performance evaluation of nonthermal plasma reactors for NO oxidation in diesel engine exhaust gas treatment

The discharge plasma-chemical hybrid process for NOinfinity removal from the flue gas emissions is an extremely effective and economical approach in comparison with the conventional selective catalytic reduction system. In this paper we bring out a relative comparison of several discharge plasma reactors from the point of NO removal efficiency. The reactors were either energized by ac or by repetitive pulses. Ferroelectric pellets were used to study the effect of pellet assisted discharges on gas cleaning. Diesel engine exhaust, at different loads; is used to approximately simulate the flue gas composition. Investigations were carried out at room temperature with respect to the variation of reaction products against the discharge power. Main emphasis is laid on the oxidation of NO to NO2, without reducing NOx concentration (i.e., minimum reaction byproducts), with least power consumption. The produced NO2 will be totally converted to N-2 and Na-2 SO4 using Na-2 SO3. The ac packed-bed reactor and pelletless pulsed corona reactor showed better performance, with minimum reaction products for a given power, when the NO concentration was low (similar to 100 ppm). When the engine load exceeds 50% (NO > 300 ppm) there was not much decrease in NO reduction and more or less all the reactors performed equally. The total operating cost of the plasma-chemical hybrid system becomes $4010/ton of NO, which is 1/3-1/5 of the conventional selective catalytic process.

Performance evaluation of nonthermal plasma reactors for NO oxidation in diesel engine exhaust gas treatment

The discharge plasma-chemical hybrid process for NO/sub x/ removal from the due gas emissions is an extremely effective and economical approach in comparison with the conventional selective catalytic reduction system. In this paper we bring out a relative comparison of several discharge plasma reactors from the point of NO removal efficiency. The reactors were either energized by AC or by repetitive pulses. Ferroelectric pellets were used to study the effect of pellet assisted discharges on gas cleaning. Diesel engine exhaust, at different loads, is used to approximately simulate the due gas composition. Investigations were carried out at room temperature with respect to the variation of reaction products against the discharge power. Main emphasis is laid on the oxidation of NO to NO/sub 2/, without reducing NOx concentration (i.e., minimum reaction byproducts), with least power consumption. The produced NO/sub 2/ will be totally converted to N/sub 2/ and Na/sub 2/SO/sub 4/ using Na/sub 2/SO/sub 3/. The AC packed bed reactor and pelletless pulsed corona reactor showed better performance, with minimum reaction products for a given power, when the NO concentration was low (/spl sim/100 ppm). At high engine loads (NO>300 ppm) there was not much decrease in NO/sub x/ reduction and more or less all the reactors performed equally. The paper discusses these observations in detail.

An Evaluation of the Effectiveness of a Charged Bilayered Conducting Fine Mesh as a Dust Filter

Aim: To develop a mesh meant to be mounted on a windowpane that will act as a barrier for dust, while allowing wind to pass freely. Materials and Methods: Two small metal meshes separated at 1 cm, connected to an electrostatic generator and holding opposite charges are used. A videographic analysis has been performed. Results: The charged bilayered mesh was able to prevent a large portion of dust from passing through. Conclusion: The device is a simple, economical, and reliable way of reducing the entry of dust into a room, easing the need for periodic cleaning, and thus creating a healthier environment for the inhabitants of the building. It also has potential space applications.

Evaluation of macrophyte control in 38 Florida lakes using triploid grass carp

Florida’s large number of shallow lakes, warm climate and long growing season have contributed to the development of excessive growths of aquatic macrophytes that have seriously interfered with many water use activities. The introduction of exotic aquatic macrophyte species such as hydrilla ( Hydrilla verticillata ) have added significantly to aquatic plant problems in Florida lakes. The use of grass carp ( Ctenopharyngodon idella ) can be an effective and economical control for aquatic vegetation such as hydrilla. Early stocking rates (24 to 74 grass carp per hectare of lake area) resulted in grass carp consumption rates that vastly exceeded the growth rates of the aquatic plants and often resulted in the total loss of all submersed vegetation. This study looked at 38 Florida lakes that had been stocked with grass carp for 3 to 10 years with stocking rates ranging from < 1 to 59 grass carp per hectare of lake and 1 to 207 grass carp per hectare of vegetation to determine the long term effects of grass carp on aquatic macrophyte communities. The median PAC (percent area coverage) value of aquatic macrophytes for the study lakes after they were stocked with grass carp was 14% and the median PVI (percent volume infested) value of aquatic macrophytes was 2%. Only lakes stocked with less than 25 to 30 fish per hectare of vegetation tended to have higher than median PAC and PVI values. When grass carp are stocked at levels of > 25 to 30 fish per hectare of vegetation the complete control of aquatic vegetation can be achieved, with the exception of a few species of plants that grass carp have extreme difficulty consuming. If the management goal for a lake is to control some of the problem aquatic plants while maintaining a small population of predominately unpalatable aquatic plants, grass carp can be stocked at approximately 25 to 30 fish per hectare of vegetation.

Economic evaluation of proposed pure and mixed stands in Central Vietnam highlands

In comparison with mixed forest stands, the cultivation of pure plantations in Vietnam entails serious ecological consequences such as loss of biodiversity and higher rate of soil erosion. The economic evaluation is elaborated between pure plantations and mixed forests where the fast-growing tree species are mixed with slow growing tree species which are planted in stripes separating the segments with fast-growing tree species (Acacia sp.). For the evaluation, the input values were used from local costs of goods, services and labour. The results show that the internal rate of return is the highest in the case of pure plantation in comparison with mixed forests – 86% to 77%(first planting pattern: Acacia sp. + noble hardwood species) and 54% (second planting pattern: Acacia + Dipterocarpus sp. + Sindora sp.). The average profit per hectare and year is almost five times higher in the case of mixed stands. The first planting pattern reaches 2,650 $, the second planting pattern 2,280 $ and the pure acacia plantation only 460 $. From an economic point of view, the cultivation of mixed forests that corresponds to the principles of sustainable forestry generates a good economical profit while maintaining habitat complexity and biodiversity.