Mechanical behavior of ceramic veneer in zirconia-based restorations: a 3-dimensional finite element analysis using microcomputed tomography data

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fast sequential multi-element determination of Ca, Mg, K, Cu, Fe, Mn and Zn for foliar diagnosis using high-resolution continuum source flame atomic absorption spectrometry: Feasibility of secondary lines, side pixel registration and least-squares background correction

The fast sequential multi-element determination of Ca, Mg, K, Cu, Fe, Mn and Zn in plant tissues by high-resolution continuum source flame atomic absorption spectrometry is proposed. For this, the main lines for Cu (324.754 nm), Fe (248.327 nm), Mn (279.482 nm) and Zn (213.857 nm) were selected, and the secondary lines for Ca (239.856 nm), Mg (202.582 nm) and K (404.414 nm) were evaluated. The side pixel registration approach was studied to reduce sensitivity and extend the linear working range for Mg by measuring at wings (202.576 nm; 202.577 nm; 202.578 nm; 202.580 nm: 202.585 nm; 202.586 nm: 202.587 nm; 202.588 nm) of the secondary line. The interference caused by NO bands on Zn at 213.857 nm was removed using the least-squares background correction. Using the main lines for Cu, Fe, Mn and Zn, secondary lines for Ca and K, and line wing at 202.588 nm for Mg, and 5 mL min(-1) sample flow-rate, calibration curves in the 0.1-0.5 mg L-1 Cu, 0.5-4.0 mg L-1 Fe, 0.5-4.0 mg L-1 Mn, 0.2-1.0 mg L-1 Zn, 10.0-100.0 mg L-1 Ca, 5.0-40.0 mg L-1 Mg and 50.0-250.0 mg L-1 K ranges were consistently obtained. Accuracy and precision were evaluated after analysis of five plant standard reference materials. Results were in agreement at a 95% confidence level (paired t-test) with certified values. The proposed method was applied to digests of sugar-cane leaves and results were close to those obtained by line-source flame atomic absorption spectrometry. Recoveries of Ca, Mg, K, Cu, Fe, Mn and Zn in the 89-103%, 84-107%, 87-103%, 85-105%, 92-106%, 91-114%, 96-114% intervals, respectively, were obtained. The limits of detection were 0.6 mg L-1 Ca, 0.4 mg L-1 Mg, 0.4 mg L-1 K, 7.7 mu g L-1 Cu, 7.7 mu g L-1 Fe, 1.5 mu g L-1 Mn and 5.9 mu g L-1 Zn. (C) 2009 Elsevier B.V. All rights reserved.

A simple method based on HR-CS FAAS for multi-element determination of Cu, Fe, Mn and Zn in medicinal plants

A simple method to determine Cu, Fe, Mn and Zn in single aliquots of medicinal plants by HR-CS FAAS is proposed. The main lines for Cu, Mn and Zn, and the alternate line measured at the wing of the main line for Fe at 248.327 nm allowed calibration within the 0.025 - 2.0 mg L-1 Cu, 1.0 - 20.0 mg L-1 Fe, 0.05 - 2.0 mg L-1 Mn, 0.025 - 0.75 mg L-1 Zn ranges. Nineteen medicinal plants and two certified plant reference materials were analyzed. Results were in agreement at a 95% confidence level (paired t-test) with reference values. Limits of detection were 0.12 μg L-1 Cu, 330 μg L-1 Fe, 1.42 μg L-1 Mn and 8.12 μg L-1 Zn. Relative standard deviations (n=12) were ≤ 3% for all analytes. Recoveries in the 89 - 105% (Cu), 95 - 108% (Fe), 94 - 107% (Mn), and 93 - 110% (Zn) ranges were obtained.

Finite element simulation of a local scale air quality model over complex terrain

[EN]In this paper we propose a finite element method approach for modelling the air quality in a local scale over complex terrain. The area of interest is up to tens of kilometres and it includes pollutant sources. The proposed methodology involves the generation of an adaptive tetrahedral mesh, the computation of an ambient wind field, the inclusion of the plume rise effect in the wind field, and the simulation of transport and reaction of pollutants. We apply our methodology to simulate a fictitious pollution episode in La Palma island (Canary Island, Spain)...

Entwicklung einer online-Chromatographie für Element 106 (Seaborgium)

Das Studium chemischer Eigenschaften der schwersten Elemente, der Transactiniden, erfordert immer leistungsfähigere Apparaturen. Wegen ihrer kurzen Halbwertszeiten müssen diese Elemente schnell von der Targetkammer mittels Gasjet zur Apparatur transportiert und dort in die wässrige Phase überführt werden. Das sollte zur Vermeidung von Verlusten durch vorzeitigen Zerfall möglichst online betrieben werden, d.h. die in der Kernreaktion gebildeten Atome werden kontinuierlich aus der Targetkammer ausgespült und in der Apparatur in die wässrige Phase überführt. Dabei stellt sich das Problem, die kleinen Aerosol-Partikel (100-200 nm und etwa 1010 Teilchen pro Liter) bei einem Gasfluss von 2 bis 3 Liter Jet-Gas pro min in eine mit 1 bis 2 mL/min fließende wässrige Lösung zu überführen. Hierzu wurden zwei verschiedene Systeme am TRIGA-Reaktor Mainz entwickelt und in Experimenten an den Schwerionenbeschleunigern am PSI und der GSI erfolgreich eingesetzt. Da die diskontinuierlich arbeitende Chemieapparatur ARCA, mit der bisher chemische Eigenschaften der Elemente 101, 103, 104, 105 und 106 bestimmt wurden, wegen niedriger Produktionsraten bei Element 106 an ihre technologischen Grenzen stößt, bestand eine weitere Aufgabe der vorliegenden Arbeit darin, ein kontinuierlich arbeitendes Chromatographiesystem aufzubauen, mit dem Verteilungskoeffizienten des Elements 106 gemessen werden können. Bei der in dieser Arbeit entwickelten und in Versuchen mit kurzlebigen Hafnium-, Wolfram- und Rutherfordium-Isotopen getesten, kontinuierlich arbeitenden Mehrsäulentechnik wird der direkte Nachweis des Transactinids aufgegeben, und die Retentionszeit in dem chromatographischen System über die Menge der während der Retention zerfallenen Atome bestimmt. Neben der apparativen Entwicklung dieser Technik, die geringste Totvolumina im System erfordert, mussten bei der Auswahl des geeigneten chemischen Systems die engen Grenzen dieser Methode beachtet werden, was umfangreiche Kenntnisse zur trägerfreien Chemie der homologen Elemente erfordert. Neben Batchexperimenten mit trägerfrei produzierten Nukliden wurde für offline-Experimente auch ARCA erfolgreich eingesetzt. Der Vergleich von Kd-Werten, die in Batchexperimenten, mit ARCA und mit der prinzipiell neuen Methode der Mehrsäulentechnik bestimmt wurden, zeigten dabei gute Übereinstimmungen. Für die Anwendbarkeit der Mehrsäulentechnik sind aber auch geeignete radioaktive Zerfallsketten notwendig, die in einem langlebigen Isotop enden sollten, welches über lange Experimentierzeiten akkumuliert werden kann. Dabei ist die Diskriminierung von einzelnen Atomen langlebiger Actiniden als Endglieder der Zerfallskette der Transactiniden gegen den natürlichen und elektronischen Untergrund sehr anspruchsvoll und möglicherweise der limitierende Faktor dieser Technik. Neben Beiträgen zur Fluoridkomplexierung von Elementen der 4. Nebengruppe (inklusive Rutherfordium) und der 6. Nebengruppe, wurde die Hydrolyse von Elementen der 6. Nebengruppe untersucht. Hier zeigen sich bei Verwendung von trägerfreien Aktivitäten abweichende Resultate gegenüber der Literatur.Auf der Grundlage dieser Daten wurde ein Mehrsäulenexperiment für 7,4-s 265Sg (Element 106) vorbereitet, für dessen Einsatz sowohl ein drehendes Targetradsystem für eine erhöhte Produktionsrate getestet wurde, als auch der Einsatz von speziell funktionalisierten Ionenaustauscherharzen.

Finite element 3D reconstruction of the pulmonary acinus imaged by synchrotron X-ray tomography

The alveolated structure of the pulmonary acinus plays a vital role in gas exchange function. Three-dimensional (3D) analysis of the parenchymal region is fundamental to understanding this structure-function relationship, but only a limited number of attempts have been conducted in the past because of technical limitations. In this study, we developed a new image processing methodology based on finite element (FE) analysis for accurate 3D structural reconstruction of the gas exchange regions of the lung. Stereologically well characterized rat lung samples (Pediatr Res 53: 72-80, 2003) were imaged using high-resolution synchrotron radiation-based X-ray tomographic microscopy. A stack of 1,024 images (each slice: 1024 x 1024 pixels) with resolution of 1.4 mum(3) per voxel were generated. For the development of FE algorithm, regions of interest (ROI), containing approximately 7.5 million voxels, were further extracted as a working subunit. 3D FEs were created overlaying the voxel map using a grid-based hexahedral algorithm. A proper threshold value for appropriate segmentation was iteratively determined to match the calculated volume density of tissue to the stereologically determined value (Pediatr Res 53: 72-80, 2003). The resulting 3D FEs are ready to be used for 3D structural analysis as well as for subsequent FE computational analyses like fluid dynamics and skeletonization.

Carbon chemistry of ODP Leg 105 sites

The quantity and quality of organic carbon of Eocene to Holocene sediments from ODP Sites 645, 646, and 647 were investigated to reconstruct depositional environments. Results were based on organic-carbon and nitrogen determinations, Rock-Eval pyrolysis, and kerogen microscopy. The sediments at Site 645 in Baffin Bay are characterized by relatively high organic-carbon values, most of which range from 0.5% to almost 3%, with maximum values in the middle Miocene. Distinct maxima of organic-carbon accumulation rates occur between 18 and 12.5 Ma and between 3.4 and 0 Ma. At Sites 646 and 647 in the Labrador Sea, organic-carbon contents vary between 0.1% and 0.75%. Cyclic 'Milankovitch-type' changes in organic-carbon deposition imply climate-controlled mechanisms that cause these fluctuations. The composition of organic matter at Site 645 is dominated by terrigenous components throughout the entire sediment sequence. An increased content of marine organic carbon was recorded only in the late-middle Miocene. At Sites 646 and 647, the origin of the organic matter most probably is marine. Oceanic paleoproductivity values were estimated, based on the amount of marine organic carbon. During most of the Neogene time interval at Site 645, productivity was low, i.e., similar or less than that measured in Baffin Bay today. Higher values of up to 150 (200) gC/m**2/y may have occurred only in the Miocene. At Sites 646 and 647, mean paleoproductivity values vary between 90 and 170 gC/m**2/y; i.e., these are also similar to those measured in the Labrador Sea today. Lower values of 40 to 70 gC/m**2/y were estimated for the early Eocene and (middle) Miocene.

Trace-element geochemistry of tholeiitic basalts from DSDP Hole 55-433C

Hole 433C, a multiple re-entry hole drilled in 1862 meters of water on Suiko Seamount in the central Emperor Seamounts, penetrated 387.5 meters of lava flows overlain by 163.0 meters of sediments. The recovered volcanic rocks consist of three flow units (1-3) of alkalic basalt underlain by more than 105 flows or flow lobes (Flow Units 4-67) of tholeiitic basalt. This study reports trace-element, including rare-earth element (REE), data for 25 samples from 24 of the least altered tholeiitic flows. These data are used to evaluate the origin and evolution of tholeiitic basalts from Suiko Seamount and to evaluate changes in the mantle source between the time when Suiko Seamount formed, 64.7 ± 1.1 m.y. ago (see Dalrymple et al., 1980), and the present day. Stearns (1946), Macdonald and Katsura (1964) and Macdonald (1968) have established that chemically distinct lavas erupt during four eruptive stages of development of a Hawaiian volcano. These stages, from initial to final, are shield-building, caldera-filling, post-caldera, and post-erosional. The lavas of the shield-building stage are tholeiitic basalts, which erupt rapidly and in great volume. The shield-building stage is quickly followed by caldera collapse and by the caldera-filling stage, during which the caldera is filled by tholeiitic and alkalic lavas. During the post-caldera stage, a relatively thin veneer of alkalic basalts and associated differentiated lavas are erupted, sometimes accompanied by minor eruptions of tholeiitic lava. After a period of volcanic quiescence and erosion, lavas of the nephelinitic suite, which include both alkalic basalts and strongly SiO2-undersaturated nephelinitic basalts, may erupt from satellite vents during the post-erosional stage. Many Hawaiian volcanoes develop through all four stages; but individual volcanoes have become extinct before the cycle is complete. We interpret the tholeiitic lavas drilled on Suiko Seamount to have erupted during either the shield-building or the caldera-filling stage, and the overlying alkalic flows to have erupted during either the caldera-filling or the post-caldera stage (see Kirkpatrick et al., 1980).

Rare earth and other element contents and speciations in samples from Core AKO26-35, Pacific Ocean, Southwest Basin

Ferromanganese micro- and macronodules in eupelagic clays at Site AKO26-35 in the Southwest Pacific Basin were studied in order to check REE distribution during ferromanganese ore formation in non-productive zones of the Pacific Ocean. Host sediments and their labile fraction, ferromanganese micronodules (in size fractions 50-100, 100-250, 250-500, and >500 ?m) from eupelagic clays (horizons 37-10, 105-110, 165-175, and 189-190 cm), and buried ferromanganese micronodules (horizons 64-68, 158-159, and 165-166 cm) were under study. Based on partition analysis data anomalous REE enrichment in eupelagic clays from Site AKO26-35 is related to accumulation of rare earth elements in iron hydroxophosphates. Concentration of Ce generally bound with manganese oxyhydroxides is governed by oxidation of Mn and Ce in ocean surface waters. Micronodules (with Mn/Fe from 0.7 to 1.6) inherit compositional features of the labile fraction of bottom sediments. Concentrations of Ce, Co, and Th depend on micronodule sizes. Enrichment of micronodules in hydrogenic or hydrothermal matter is governed by their sizes and by a dominant source of suspended oxyhydroxide material. The study of buried ferromanganese micronodules revealed general regularities in compositional evolution of oxyhydroxide matrices of ferromanganese micro- and macronodules. Compositional variation of micro- and macronodules relative to the labile fraction of sediments in the Pacific non-productive zone dramatically differs from the pattern in bioproductive zones where micronodule compositions in coarser fractions are similar to those in associated macronodules and labile fractions of host sediments due to more intense suboxidative diagenesis.

A numerical discrete element study on the influence of an embedded viscoelastic-plastic layer at different viscosity values

The major aim of this study was to examine the influence of an embedded viscoelastic-plastic layer at different viscosity values on accretionary wedges at subduction zones. To quantify the effects of the layer viscosity, we analysed the wedge geometry, accretion mode, thrust systems and mass transport pattern. Therefore, we developed a numerical 2D 'sandbox' model utilising the Discrete Element Method. Starting with a simple pure Mohr Coulomb sequence, we added an embedded viscoelastic-plastic layer within the brittle, undeformed 'sediment' package. This layer followed Burger's rheology, which simulates the creep behaviour of natural rocks, such as evaporites. This layer got thrusted and folded during the subduction process. The testing of different bulk viscosity values, from 1 × 10**13 to 1 × 10**14 (Pa s), revealed a certain range where an active detachment evolved within the viscoelastic-plastic layer that decoupled the over- and the underlying brittle strata. This mid-level detachment caused the evolution of a frontally accreted wedge above it and a long underthrusted and subsequently basally accreted sequence beneath it. Both sequences were characterised by specific mass transport patterns depending on the used viscosity value. With decreasing bulk viscosities, thrust systems above this weak mid-level detachment became increasingly symmetrical and the particle uplift was reduced, as would be expected for a salt controlled forearc in nature. Simultaneously, antiformal stacking was favoured over hinterland dipping in the lower brittle layer and overturning of the uplifted material increased. Hence, we validated that the viscosity of an embedded detachment strongly influences the whole wedge mechanics, both the respective lower slope and the upper slope duplex, shown by e.g. the mass transport pattern.

Sedimentary facies, clay mineralogy and geochemistry of the Paleogene sediments of ODP Site 105-647

Claystones immediately overlying the early Eocene age ocean-floor basalt, cored at Ocean Drilling Program (ODP) Site 647, underwent hydrothermal and thermal alterations originating from the basalt, which resulted in changes in both the mineralogical and chemical composition of the sediments. Chlorites and higher magnesium and iron concentrations were found in the lowermost sediment sequence. Upcore, changes in the bulk chemical composition of the sediments become smaller, when compensated for variations in the carbonate content originating from biogenic and authigenic components. Chlorite disappears upcore, but still only part of the swelling clay minerals have survived the thermal influence. Thirty meters above the basalt, the clay mineralogy and chemical composition become uniform throughout the Paleogene section. Iron-rich smectites (i.e., nontronitic types), totally dominate the clay mineral assemblage. Biogenic components, responsible for the dominant part of the calcite and cristobalite contents, vary in amount in the upper part, and so do the authigenic carbonate and sulfide contents. Detrital components, such as kaolinite, illite, quartz, and feldspars, make up a very small proportion of the sediment record. The nontronitic smectites are believed to be authigenic, formed by a supply of iron from the continuous formation of ocean-floor basalt in the ridge area that reacted with the detrital and biogenic silicates and alumina silicates.

Geochemical characterizations of the Cretaceous formations at DSDP Holes 93-603B and 11-105

Geochemical characterizations of the Cretaceous formations at Site 603 are quite comparable with those at Site 105. In the Blake-Bahama and the Hatteras formations, the petroleum potential is medium (<5 kg HC/t of rock) to very low (<0.5 kg HC/t of rock), and the organic matter is mainly of type III origin, that is, terrestrial. At the top of the Hatteras Formation, there is a condensed series, which chiefly contains organic matter of type II origin, with up to 20 wt.% total organic carbon content in Core 603B-34 and 25 wt.% in Core 105-9. This accumulation corresponds to the Cenomanian/Turonian boundary event. An examination of dinoflagellates in the kerogen concentration assigns dates to the samples studied by organic geochemistry. The Cenomanian and Turonian age of the organic-matter-rich black claystones indicates a low rate of sedimentation, about 1 m/Ma. Furthermore, the occurrence of type II organic matter indicates an anoxic environment with insufficient oxygen renewal to oxidize the sinking hemipelagic organic matter. This organic enrichment is not related to local phenomena but to sedimentation over an extended area, because deposits are well known in various areas with different paleodepths in the North Atlantic.