Field Testing of Railroad Flatcar Bridges Volume II: Multiple Spans, TR-498, 2007

Based on the conclusions of IHRB Project TR-444, Demonstration Project Using Railroad Flat Car Bridges for Low Volume Road Bridges, additional research on the use of RRFC bridges was undertaken. This portion of the project investigated the following: (1) Different design and rating procedures; (2) Additional single span configurations plus multiple span configurations; (3) Different mechanisms for connecting adjacent RRFCs and the resulting lateral load distribution factors; (4) Sheet pile abutments; and (5) Behavior RRFCs that had been strengthened so that they could be used on existing abutments. A total of eight RRFC bridges were tested (five single span bridges, two two-span bridges, and one three-span bridge). Based on the results of this study a simplified design and rating procedure has been developed for the economical replacement bridge alternative. In Volume 1, the results from the testing of four single span RRFC bridges are presented, while in Volume 2,this volume, the results from the testing of the strengthened single span bridge plus the three multiple span bridges are presented.

Field and Laboratory Evaluation of Precast Concrete Bridges, TR-440, 2001

Recent data compiled by the National Bridge Inventory revealed 29% of Iowa's approximate 24,600 bridges were either structurally deficient or functionally obsolete. This large number of deficient bridges and the high cost of needed repairs create unique problems for Iowa and many other states. The research objective of this project was to determine the load capacity of a particular type of deteriorating bridge – the precast concrete deck bridge – which is commonly found on Iowa's secondary roads. The number of these precast concrete structures requiring load postings and/or replacement can be significantly reduced if the deteriorated structures are found to have adequate load capacity or can be reliably evaluated. Approximately 600 precast concrete deck bridges (PCDBs) exist in Iowa. A typical PCDB span is 19 to 36 ft long and consists of eight to ten simply supported precast panels. Bolts and either a pipe shear key or a grouted shear key are used to join adjacent panels. The panels resemble a steel channel in cross-section; the web is orientated horizontally and forms the roadway deck and the legs act as shallow beams. The primary longitudinal reinforcing steel bundled in each of the legs frequently corrodes and causes longitudinal cracks in the concrete and spalling. The research team performed service load tests on four deteriorated PCDBs; two with shear keys in place and two without. Conventional strain gages were used to measure strains in both the steel and concrete, and transducers were used to measure vertical deflections. Based on the field results, it was determined that these bridges have sufficient lateral load distribution and adequate strength when shear keys are properly installed between adjacent panels. The measured lateral load distribution factors are larger than AASHTO values when shear keys were not installed. Since some of the reinforcement had hooks, deterioration of the reinforcement has a minimal affect on the service level performance of the bridges when there is minimal loss of cross-sectional area. Laboratory tests were performed on the PCDB panels obtained from three bridge replacement projects. Twelve deteriorated panels were loaded to failure in a four point bending arrangement. Although the panels had significant deflections prior to failure, the experimental capacity of eleven panels exceeded the theoretical capacity. Experimental capacity of the twelfth panel, an extremely distressed panel, was only slightly below the theoretical capacity. Service tests and an ultimate strength test were performed on a laboratory bridge model consisting of four joined panels to determine the effect of various shear connection configurations. These data were used to validate a PCDB finite element model that can provide more accurate live load distribution factors for use in rating calculations. Finally, a strengthening system was developed and tested for use in situations where one or more panels of an existing PCDB need strengthening.

Influence of the supply of reactive power in the calculation of the transfer capability

This paper presents some initial concepts for including reactive power in linear methods for computing Available Transfer Capability (ATC). It is proposed an approximation for the reactive power flows computation that uses the exact circle equations for the transmission line complex flow, and then it is determined the ATC using active power distribution factors. The transfer capability can be increased using the sensitivities of flow that show the best group of buses which can have their reactive power injection modified in order to remove the overload in the transmission lines. The results of the ATC computation and of the use of the sensitivities of flow are presented using the Cigré 32-bus system. © 2004 IEEE.

Simple mechanochemistry describes the dynamics of kinesin molecules

Recently, Block and coworkers [Visscher, K., Schnitzer, M. J., & Block, S. M. (1999) Nature (London) 400, 184–189 and Schnitzer, M. J., Visscher, K. & Block, S. M. (2000) Nat. Cell Biol. 2, 718–723] have reported extensive observations of individual kinesin molecules moving along microtubules in vitro under controlled loads, F = 1 to 8 pN, with [ATP] = 1 μM to 2 mM. Their measurements of velocity, V, randomness, r, stalling force, and mean run length, L, reveal a need for improved theoretical understanding. We show, presenting explicit formulae that provide a quantitative basis for comparing distinct molecular motors, that their data are satisfactorily described by simple, discrete-state, sequential stochastic models. The simplest (N = 2)-state model with fixed load-distribution factors and kinetic rate constants concordant with stopped-flow experiments, accounts for the global (V, F, L, [ATP]) interdependence and, further, matches relative acceleration observed under assisting loads. The randomness, r(F,[ATP]), is accounted for by a waiting-time distribution, ψ\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \setlength{\oddsidemargin}{-69pt} \begin{document} \begin{equation*}{\mathrm{_{1}^{+}}}\end{equation*}\end{document}(t), [for the transition(s) following ATP binding] with a width parameter ν ≡ 〈t〉2/〈(Δt)2〉≃2.5, indicative of a dispersive stroke of mechanicity ≃0.6 or of a few (≳ν − 1) further, kinetically coupled states: indeed, N = 4 (but not N = 3) models do well. The analysis reveals: (i) a substep of d0 = 1.8–2.1 nm on ATP binding (consistent with structurally based suggestions); (ii) comparable load dependence for ATP binding and unbinding; (iii) a strong load dependence for reverse hydrolysis and subsequent reverse rates; and (iv) a large (≳50-fold) increase in detachment rate, with a marked load dependence, following ATP binding.

Conformational analysis and dielectric relaxation of polycarbosilanes and related materials

The conformational characteristics of poly(dimethylsilmethylene), poly(dimethylsilethene), poly(dimethylsilethane) and a related material, poly(2,2,5,5-tetramethyl-1-oxa-2,5-disilapentane), have been investigated using the method of molecular mechanics. In this method, a quantitative analysis of the factors affecting the nature and magnitude of the bond rotation potentials governing their conformational behaviour has been undertaken. Along with their structural data, the results obtained were employed to calculate a variety of conformationally-dependent properties for these polymers, including the characteristic ratio, the dipole moment ratio and the mean-square radius of gyration. In addition, the dielectric relaxation behaviour of two samples of poly(2,2,5,5-tetramethyl-1-oxa-2,5-disilapentane) with molar masses Mw = 28000 and Mw = 46000 respectively, have been studied as a function of temperature (179K-205K) and frequency (100-105Hz). Activation energies for the α-relaxation process and Davidson-Cole empirical distribution factors have been calculated.

Dielectric relaxation of polysiloxanes and kerr effect of p-phenylene vinylene oligomers

The dielectric relaxation behaviour of a series of cyclic and linear poly(dimethylsiloxanes) with overline nn in the range 28 to 99 has been studied, as a function of temperature (142.0K-157.5K) and frequency (12-105Hz). Activation energies for the -relaxation process, Davidson-Cole empirical distribution factors, , and mean-square dipole moments per repeat unit, < 2> , have been calculated. Differences in values of H_act reflected restricted dipolar rotation for the cyclic structures, compared to the linear structures, over the range of molecular weights studied. The dielectric relaxation behaviour of a series of linear oligomers of methyl phenyl siloxane, with n in the range 4 to 10, a series of linear fractions of poly(methyl phenyl siloxane), with overline n_n in the range 31 to 1370, and a cyclic oligomer of mehyl phenyl siloxane, with n = 10, has been studied as a function of temperature (155.5K-264.0K) and frequency (12-105Hz). Activation energies for the -relaxation process, Davidson-Cole and Cole-Cole empirical distribution factors, and , respectively, and mean-square dipole moments per repeat unit have been calculated. The reduced flexibility of short methyl phenyl siloxane chains, compared to dimethyl siloxane chains, was apparent from a comparison of dipole moment ratios. The dilectric relaxation behaviour of poly(methyl hydrogen siloxane) and poly(n-hexyl methyl siloxane) has been studied as a function of temperature and frequency. A polysiloxane liquid crystal has been synthesised and its dielectric relaxation behaviour has been studied, as a function of temperature and frequency, in the liquid crystalline phase and below T_g. Poly(p-phenylene vinylene) and related oligomers have been synthesised and characterised by a variety of experimental techniques. The Kerr effect of two oligomeric fractions, in solution in PPG 2025, has been measured. The electrical conductivities of the undoped and I_2-doped polymer and oligomers have been measured.

Prevalence and social distribution of risk factors for chronic noncommunicable diseases in Brazil

OBJETIVOS: Evaluar los factores de riesgo de enfermedades crónicas no transmisibles (ECNT) e identificar las desigualdades sociales relacionadas con su distribución en la población adulta brasileña.MÉTODOS: Se estudiaron los factores de riesgo de ECNT (entre ellos el consumo de tabaco, el sobrepeso y la obesidad, el bajo consumo de frutas y vegetales [BCFV], la insuficiente actividad física en el tiempo de ocio [IAFTO], el estilo de vida sedentario y el consumo excesivo de alcohol) en una muestra probabilística de 54369 adultos de 26 capitales estatales de Brasil y el Distrito Federal en 2006. Se utilizó el Sistema de Vigilancia de los Factores Protectores y de Riesgo para Enfermedades Crónicas No Transmisibles por Entrevistas Telefónicas (VIGITEL), un sistema de encuestas telefónicas asistido por computadora, y se calcularon las prevalencias ajustadas por la edad para las tendencias en cuanto al nivel educacional mediante la regresión de Poisson con modelos lineales. RESULTADOS: Los hombres informaron mayor consumo de tabaco, sobrepeso, BCFV, estilo de vida sedentario y consumo excesivo de alcohol que las mujeres, pero menos IAFTO. En los hombres, la educación se asoció con un mayor sobrepeso y un estilo de vida sedentario, pero con un menor consumo de tabaco, BCFV e IAFTO. En las mujeres, la educación se asoció con un menor consumo de tabaco, sobrepeso, obesidad, BCFV e IAFTO, pero aumentó el estilo de vida sedentario CONCLUSIONES: En Brasil, la prevalencia de factores de riesgo para ECNT (excepto IAFTO) es mayor en los hombres que en las mujeres. En ambos sexos, el nivel de educación influye en la prevalencia de los factores de riesgo para ECNT

Biotic and Abiotic factors in the distribution of resident fish species : a case study from two islets and an adjacent shoreline in Terceira Island, Azores, Portugal

XV European Congress of Ichthyology, Porto, Portugal, 7 Sep - 11 Sep, 2015.

The influence of geometric factors on the wall shear stress distribution in realistic human coronary arteries

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia Biomédica. A presente dissertação foi desenvolvida no Erasmus Medical Center em Roterdão, Holanda

Candida esophagitis: species distribution and risk factors for infection

Although Candida albicans is the main cause of fungal esophagitis, other species such as C. tropicalis, C. krusei and C. stellatoidea have also been implicated. Several studies have identified risk factors for C. albicans esophagitis. However, data for non-C. albicans species is still sparse. The aim of this study was to determine the etiology of Candida esophagitis in our medical centre over an 18-month period. Additionally, we aimed to investigate predisposing conditions for esophageal candidosis caused by different Candida species. A total of 21,248 upper gastroscopies were performed in Santa Casa Complexo Hospitalar between January 2005 and July 2006. The prevalence of Candida esophagitis was 0.74% (n = 158). C. albicans caused the vast majority of infections (96.2%), followed by C. tropicalis (2.5%), C. lusitaniae (0.6%) and C. glabrata (0.6%). There were 81 women (51.3%) and 77 men (48.7%). No case of mixed infection occurred. Concomitant oral candidosis was documented for 10.8% (n = 17). Most of cases (55.1%) involved outpatients. Around one fifth of patients in our cohort had no identifiable risk factors for esophageal candidosis (20.8%). Since nearly all infections were caused by C. albicans we were not able to determine risk factors for esophagitis caused by other Candida species.

Distribution of risk factors in parents and siblings of patients with early coronary artery disease

OBJECTIVE: Early coronary artery disease (CAD) is associated with risk factors (RF). Offspring of parents with a RF have a greater prevalence of them. However, the distribution of RF in parents and siblings of patients with early CAD is unknown. METHODS: The study comprised the parents and siblings of 42 patients with early CAD (< 45 years), 29 males. Their mean age was 39.5±3.7 years. The following major RF were analyzed: smoking (> 5 cigarretes/day), hypercholesterolemia (total cholesterol > 200 mg/dL), hypertension (diastolic blood pressure > 90 mmHg), and diabetes (glycemia > 126 mg/dL). RESULTS: Of a total of 102 RF, 4, 3, 2, and 1 were observed in, respectively, 5, 15, 15, and 7 patients with early CAD, the most prevalent being smoking (86%) and hypercholesterolemia (83%). Diabetes was observed in 15 (36%) and hypertension in 16 (38%) patients. Smoking was more prevalent in the fathers (76%) and hypercholesterolemia in the mothers (30%). In 183 siblings, 131 RF were observed (1 patient with the disease had a mean of 4.7 siblings). The prevalences of smoking, hypertension, hypercholesterolemia, and diabetes in the siblings were, respectively, 32%, 18%, 14%, and 9%. The incidence of RF was as follows: 72 (39%) siblings had 1 RF, 25 (14%) siblings had 2 RF, and 3 (2%) siblings had 3 RF. In parents and their offspring, smoking was moderately correlated (r=0.43; P=0.02) with CAD. CONCLUSION: Smoking habit of parents is passed on to offspring, and, in association with hypercholesterolemia, it was the major cause of early CAD in offspring. High prevalence of smoking in offspring shows the potential responsibility of parents in the incidence of the disease in offspring.

Evaluation of Chemical and Physical-morphological Factors as Potential Determinants of Biomphalaria pfeifferi (Krauss, 1848) Distribution

This study was carried out in five sites along a small perennial river system in south-central Tanzania, which had been identified as the focus for transmission of intestinal schistosomiasis in the area. Malacological surveys preceding the study showed a focal distribution of Biomphalaria pfeifferi, intermediate host snail of Schistosoma mansoni, the snails being present in three sites but absent from the other two sites. The objective of this study was to evaluate to what extent chemical and/or physical-morphological factors determine the distribution of B. pfeifferi between these five sites. It was found that none of the chemical constituents in the waters examined were outside the tolerance range of B. pfeifferi snails. Moreover, the composition of water from B. pfeifferi-free sites was not different from that in those sites where snails occurred. Furthermore, none of the physical-morphological constituents seemed likely to be a determinant for the absence of B. pfeifferi. In view of these findings, and those of previous studies, it is concluded that the focal distribution of B. pfeifferi cannot be associated with a single environmental factor and is rather the result of more complex interactions of habitat factors

The distribution of Biomphalaria spp. in different habitats in relation to physical, biological, water contact and cognitive factors in a rural area in Minas Gerais, Brazil

A total of 256 sites in 11 habitats were surveyed for Biomphalaria in Melquiades rural area (State of Minas Gerais) in August and November 1999 and in March 2000. Of the 1,780 Biomphalaria collected, 1,721 (96.7%) were B. glabrata and 59 (3.3%) B. straminea. Snails were found in all habitats except in wells, with the largest mean numbers in tanks, seepage ponds and canals, and the smallest numbers in springs, rice fields and fishponds. People's knowledge of the occurrence of Biomphalaria at the collection sites and the presence of Biomphalaria ova were strongly correlated with the occurrence of snails, and distance between houses and collection sites, as well as water velocity were inversely correlated with Biomphalaria occurrence (p < 0.001). The strongest predictor o f Biomphalaria occurrence was the presence of tilapia fish in fishponds. Fourteen Biomphalaria (0.8% of all snails) found at 6 sites were infected with Schistosoma mansoni. Suggestions are made for the utilization of local people's knowledge in snail surveys and further studies are recommended on the possible use of tilapia for biological control of Biomphalaria in fishponds, as well as modeling of S. mansoni transmission and reinfection.

Prevalence of human papillomavirus infection, distribution of viral types and risk factors in cervical samples from human immunodeficiency virus-positive women attending three human immunodeficiency virus-acquired immune deficiency syndrome reference centres in northeastern Brazil

Human immunodeficiency virus (HIV)-positive patients have a greater prevalence of coinfection with human papillomavirus (HPV) is of high oncogenic risk. Indeed, the presence of the virus favours intraepithelial squamous cell lesion progression and may induce cancer. The aim of this study was to evaluate the prevalence of HPV infection, distribution of HPV types and risk factors among HIV-positive patients. Cervical samples from 450 HIV-positive patients were analysed with regard to oncotic cytology, colposcopy and HPV presence and type by means of polymerase chain reaction and sequencing. The results were analysed by comparing demographic data and data relating to HPV and HIV infection. The prevalence of HPV was 47.5%. Among the HPV-positive samples, 59% included viral types of high oncogenic risk. Multivariate analysis showed an association between HPV infection and the presence of cytological alterations (p = 0.003), age greater than or equal to 35 years (p = 0.002), number of partners greater than three (p = 0.002), CD4+ lymphocyte count < 200/mm3 (p = 0.041) and alcohol abuse (p = 0.004). Although high-risk HPV was present in the majority of the lesions studied, the low frequency of HPV 16 (3.3%), low occurrence of cervical lesions and preserved immunological state in most of the HIV-positive patients were factors that may explain the low occurrence of precancerous cervical lesions in this population.

Distribution of metals exposure and associations with cardiometabolic risk factors in the "Modeling the Epidemiologic Transition Study".

BACKGROUND: Metals are known endocrine disruptors and have been linked to cardiometabolic diseases via multiple potential mechanisms, yet few human studies have both the exposure variability and biologically-relevant phenotype data available. We sought to examine the distribution of metals exposure and potential associations with cardiometabolic risk factors in the "Modeling the Epidemiologic Transition Study" (METS), a prospective cohort study designed to assess energy balance and change in body weight, diabetes and cardiovascular disease risk in five countries at different stages of social and economic development. METHODS: Young adults (25-45 years) of African descent were enrolled (N = 500 from each site) in: Ghana, South Africa, Seychelles, Jamaica and the U.S.A. We randomly selected 150 blood samples (N = 30 from each site) to determine concentrations of selected metals (arsenic, cadmium, lead, mercury) in a subset of participants at baseline and to examine associations with cardiometabolic risk factors. RESULTS: Median (interquartile range) metal concentrations (μg/L) were: arsenic 8.5 (7.7); cadmium 0.01 (0.8); lead 16.6 (16.1); and mercury 1.5 (5.0). There were significant differences in metals concentrations by: site location, paid employment status, education, marital status, smoking, alcohol use, and fish intake. After adjusting for these covariates plus age and sex, arsenic (OR 4.1, 95% C.I. 1.2, 14.6) and lead (OR 4.0, 95% C.I. 1.6, 9.6) above the median values were significantly associated with elevated fasting glucose. These associations increased when models were further adjusted for percent body fat: arsenic (OR 5.6, 95% C.I. 1.5, 21.2) and lead (OR 5.0, 95% C.I. 2.0, 12.7). Cadmium and mercury were also related with increased odds of elevated fasting glucose, but the associations were not statistically significant. Arsenic was significantly associated with increased odds of low HDL cholesterol both with (OR 8.0, 95% C.I. 1.8, 35.0) and without (OR 5.9, 95% C.I. 1.5, 23.1) adjustment for percent body fat. CONCLUSIONS: While not consistent for all cardiometabolic disease markers, these results are suggestive of potentially important associations between metals exposure and cardiometabolic risk. Future studies will examine these associations in the larger cohort over time.