Implications of Longterm Diameter-Limit Harvesting: Effects on Radial Growth of Red Spruce (Picea rubens) and Genetic Diversity of White Pine (Pinus strobus)

For over 3 centuries, diameter-limit harvesting has been a predominant logging method in the northeastern United States. Silvicultural theory asserts that such intensively selective harvesting can lead to genetic degradation. A decrease in softwood productivity has recently been reported in Maine - has a long history of dysgenic selection degraded the genetic resources of Maine softwoods, contributing to a decrease in growth and productivity? This study examines two aspects of potential implications of diameter-limit harvesting: effects on residual phenotypes of red spruce and impacts on genetic diversity of white pine. Radial growth of residual red spruce trees in stands experiencing 50 years of fixed diameter-limit harvesting was measured using annual increment rings and compared with residual red spruce trees in positive selection stands. Trees remaiaing after several rounds of diameter-limit harvesting exhibited sigdicantl y smaller radial sizes throughout their lives, and displayed significantly slower growth rates for the first 80 years of measured growth. These results strongly suggest that the largest and fastest-growing genotypes and their respective gene complexes determining good radial growth have been removed from the diameter-limit stand. Dysgenic selection can be observed in fixed diarneter-limit stands, resulting in a diminished genetic resource and decreased residual stand value. To examine more direct genetic implications of long-term diameter-limit harvesting, microsatellite DNA markers were implemented to study genetic diversity of eastern white pine in Maine. Three age groups of trees were studied: mature trees older than 200 years, juvenile trees 5-30 years old, and embryos. Trees were genotyped at 10 microsatellite loci. Overall genetic diversity levels of eastern white pine in Maine were extremely high, with an average observed heterozygosity of 0.762. Genetic differentiation was minimal among and between all three age groups, although an excess of heterozygotes was shown in the mature and juvenile groups that was not reflected in the embryo group, which actually had a slight heterozygote deficiency. Allele frequencies did not differ significantly between age groups, but did reveal more rare and low frequency alleles in the embryo groups than in the mature group. Overall, low frequency alleles comprise the largest portion of alleles in the sample population, with no common alleles evident overall. These results suggest that significant genetic degradation has either not occurred for white pine, or that the results of dysgenic selection have not yet emerged. It is clear, however, that selective harvesting could result in a loss of low frequency alleles, which are a primary reserve of evolutionary potential in a species. Implications of these studies affect industrial forestry, regional economics, and ecological concerns for the northeast. Long-term diameter-limit harvesting can lead to a degradation of residual phenotypes, and an overall decrease in stand quality. Potentially, a loss of low frequency, locally adapted alleles could result in a decrease of allelic richness and degradation of the regidnal genetic resource. Decreased genetic variation can lead to seriously limited evolutionary potential of species and ecosystems, particularly in rapidly changing environments. Based on these findings, I recommend a reassessment of any harvesting prescription that includes fixed diameter-limit removals, particularly for species that have low natural genetic diversity levels or a limited natural range, such as red spruce. Maintenance of a healthy genetic reserve can avoid effects of dysgenic harvesting.

Acupuncture Increases The Diameter And Reorganisation Of Collagen Fibrils During Rat Tendon Healing.

Our previous study showed that electroacupuncture (EA) increases the concentration and reorganisation of collagen in a rat model of tendon healing. However, the ultrastructure of collagen fibrils after acupuncture is unknown. To assess the effect of acupuncture protocols on the ultrastructure of collagen fibrils during tendon healing. Sixty-four rats were divided into the following groups: non-tenotomised (normal group), tenotomised (teno group), tenotomised and subjected to manual acupuncture at ST36 (ST36 group), BL57 (BL57 group) and ST36+BL57 (SB group) and EA at ST36+BL57 (EA group). The mass-average diameter (MAD) and the reorganisation of collagen fibril diameters were determined during the three phases of tendon healing (at 7, 14 and 21 days). The MAD increased during the three phases of healing in the SB group. In the EA group, MAD increased initially but was reduced at day 21. The reorganisation of collagen fibrils was improved in the EA and SB groups at days 14 and 21, respectively. EA at day 21 appeared to reduce the reorganisation. These results indicate that the use of EA up to day 14 and manual acupuncture at ST36+BL57 up to day 21 improve the ultrastructure of collagen fibrils, indicating strengthening of the tendon structure. These data suggest a potential role for acupuncture in rehabilitation protocols.

Influence Of Successive Light-activation On Degree Of Conversion And Knoop Hardness Of The First Layered Composite Increment.

To evaluate the influence of light-activation of second, third and fourth increments on degree of conversion (DC) and microhardness (KHN) of the top (T) and bottom (B) surface of the first increment. Forty samples (n = 5) were prepared. In groups 1-4, after each increment light-activation (multiple irradiation), T and B of the first increment were measured in DC and KHN. In groups 5-8, only the first increment was made (single irradiation) and measurements of DC and KHN were taken at 15 min intervals. The light-activation modes were (XL) 500 mW/cm(2) × 38 s (G1/G5); (S) 1000 mW/cm(2) × 19 s (G2/G6), (HP) 1400 mW/cm(2) × 14 s (G3/G7); (PE) 3200 mW/cm(2) × 6 s (G4/G8). Data for DC and KHN were analyzed separately by using PROC MIXED for repeated measures and Tukey-Kramer test (α = 0.05). For KHN, B showed lower values than T. PE resulted in lower values of KHN in B surface. For single and multiple irradiations, T and B of first measurement showed the lowest KHN and the fourth measurement showed the highest, with significant difference between them. For single irradiation, first and second increments presented similar KHN, different from the third and fourth increment, which did not differ between them. For multiple irradiations, the second light-activation resulted in KHN similar to first, third and fourth increments. For DC, except QTH, T presented higher DC than B. The light-activation of successive increments was not able to influence the KHN and DC of the first increment.

INFLUENCE OF ALTITUDE, AGE AND DIAMETER ON YIELD AND ALPHA-BISABOLOL CONTENT OF CANDEIA TREES (Eremanthus erythropappus)

The heartwood of candeia tree is a source of essential oil rich in alpha-bisabolol, a substance widely used in the cosmetic and pharmaceutical industry. Bearing in mind the economic importance of alpha-bisabolol, this work aimed to evaluate the influence of tree age on the yield and content of alpha-bisabolol present in essential oil from candeia, considering two distinct reliefs and three diameter classes, in Aiuruoca region, south Minas Gerais state. The two distinct reliefs correspond respectively to one section of the stand growing at 1,000m of altitude (Area 1) and another section growing at 1,100m of altitude (Area 2). In each section, 15 trees were felled from among 3 different diameter classes. Discs were removed from the base of each tree to estimate their age by doing growth ring count. Soil samples were taken and Subjected to physical and chemical analysis. The logs were reduced into chips and random samples were taken for distillation to extract essential oil. The method used was steam distillation at a pressure of 2 kgf/cm(2)/2.5 h. The chemical analysis was performed in a gas chromatograph (GC) based on the alpha-bisabolol standard reference. The yield of essential oil from trees in Area I was higher than that from trees in Area 2, with the same pattern of influence for older trees. In Area 2, the alpha-bisabolol content was higher in younger trees. No differences were found between the relevant parameters in relation to diameter classes.

The Lobel-Komlos-Sos conjecture for trees of diameter 5 and for certain caterpillars

Loebl, Komlos, and Sos conjectured that if at least half the vertices of a graph G have degree at least some k is an element of N, then every tree with at most k edges is a subgraph of G. We prove the conjecture for all trees of diameter at most 5 and for a class of caterpillars. Our result implies a bound on the Ramsey number r( T, T') of trees T, T' from the above classes.

Influence of concrete strength and length/diameter on the axial capacity of CFT columns

This paper presents an experimental analysis of the confinement effects in steel-concrete composite columns regarding two parameters: concrete compressive strength and column slenderness. Sixteen concrete-filled steel tubular columns with circular cross section were tested under axial loading. The tested columns were filled by concrete with compressive strengths of 30, 60. 80, and 100 MPa, and had length/diameter ratios of 3, 5, 7, and 10. The experimental values of the columns` ultimate load were compared to the predictions of 4 code provisions: the Brazilian Code NBR 8800:2008, Eurocode 4 (EN 1994-1-1:2004), AINSI/AISC 360:2005, and CAN/CSA S16-01:2001. According to the results, the load capacity of the composite columns increased with increasing concrete strength and decreased with increasing length/diameter ratio. In general, the code provisions were highly accurate in the prediction of column capacity. Among them, the Brazilian Code was the most conservative, while Eurocode 4 presented the values closest to the experimental results. (C) 2009 Elsevier Ltd. All rights reserved.

Friction factor for small diameter polyethylene pipes

On this paper, the results of an experimental study oil the hydraulic friction loss for small-diameter polyethylene pipes are reported. The experiment was carried out using a range of Reynolds number between 6000 to 72000, obtained by varying discharge at 20 degrees C water temperature, with internal pipe diameters of 10.0 mm, 12.9 mm, 16.1 mm, 17.4 mm and 19.7 mm. According to the analysis results and experimental conditions, the friction factor 0 of the Darcy-Weisbach equation call be estimated with c = 0.300 and m = 0.25. The Blasius equation (c = 0.316 and m = 0.25) gives an overestimate of friction loss, although this fact is non-restrictive for micro-irrigation system designs. The analysis shows that both the Blasius and the adjusted equation parameters allow for accurate friction factor estimates, characterized by low mean error (5.1%).

Tree-ring formation, radial increment periodicity, and phenology of tree species from a seasonal semi-deciduous forest in southeast Brazil

Many tropical tree species produce growth rings in response to seasonal environmental factors that influence the activity of the vascular cambium. We applied the following methods to analyze the annual nature of treering formation of 24 tree species from a seasonal semi-deciduous forest of southeast Brazil: describing wood anatomy and phenology, counting tree rings after cambium markings, and using permanent dendrometer bands. After 7 years of systematic observations and measurements, we found the following: the trees lost their leaves during the dry season and grew new leaves at the end of the same season; trunk increment dynamics corresponded to seasonal changes in precipitation, with higher increment (active period) during the rainy season (October-April) and lower increment (dormant period) during the dry season (May-September); the number of tree rings formed after injuries to the cambium coincided with the number of years since the extraction of the wood samples. As a result of these observations, it was concluded that most study trees formed one growth ring per year. This suggests that tree species from the seasonal semi-deciduous forests of Brazil have an annual cycle of wood formation. Therefore, these trees have potential for use in future studies of tree age and radial growth rates, as well as to infer ecological and regional climatic conditions. These future studies can provide important information for the management and conservation of these endangered forests.

Effect of density on spatial distribution, pit formation and pit diameter of Myrmeleon acer Walker, (Neuroptera : Myrmeleontidae): patterns and processes

The effect of increasing population density on the formation of pits, their size and spatial distribution, and on levels of mortality was examined in the antlion Myrmeleon acer Walker. Antlions were kept at densities ranging from 0.4 to 12.8 individuals per 100 cm(2). The distribution of pits was regular or uniform across all densities, but antlions constructed proportionally fewer and smaller pits as density increased. Mortality through cannibalism was very low and only occurred at densities greater than five individuals per 100 cm(2). Antlions in artificially crowded situations frequently relocated their pits and when more space became available, individuals became more dispersed with time. Redistribution of this species results from active avoidance of other antlions and sand throwing associated with pit construction and maintenance, rather than any attempt to optimise prey capture per se.

Infrarenal aortic diameter predicts all-cause mortality

Objective - To assess the relationship between infrarenal aortic diameter and subsequent all-cause mortality in men aged 65 years or older. Methods and Results - Aortic diameter was measured using ultrasound in 12 203 men aged 65 to 83 years as part of a trial of screening for abdominal aortic aneurysms. A range of cardiovascular risk factors was also documented. Mortality over the next 3 to 7 years was assessed using record linkage. Initial aortic diameter was categorized into 10 intervals, and the relationship between increasing diameter and subsequent mortality was explored using Cox proportional hazard models. Median diameter increased from 21.4 mm in the youngest men to 22.1 mm in the oldest men. The cumulative all-cause mortality increased in a graded fashion with increasing aortic diameter. Using the diameter interval 19 to 22 mm as the reference, the adjusted hazard ratio for all-cause mortality increased from 1.26 (95% CI: 1.09, 1.44; P = 0.001) for aortic diameters of 23 to 26 mm to 2.38 (95% CI: 1.22, 4.61; P = 0.011) for aortic diameters of 47 to 50 mm. Analysis of causes of death indicated that cardiovascular disease was an important contributor to this increase. Conclusion - Infrarenal aortic diameter is an independent marker of subsequent all-cause mortality.

Morphometric Study on the Anatomy of the Fetal Cricoid Cartilage and Comparison Between Its Inner Diameter and Endotracheal Tube Sizes

Objectives: The high incidence of respiratory disorders is one of the main problems in perinatal medical care. With the increased use of intubation, the incidence of laryngeal injury causing stenosis has also increased. The principal constriction point in the infant`s larynx is the midcricoid area. We sought to provide detailed morphometric data on the anatomy of the cricoid cartilage and its relationship with growth and body characteristics of fetuses at 5 to 9 months of gestational age. Methods: Nineteen larynges obtained from 17 stillborn infants and 2 newborn infants ranging in gestational age from 5 to 9 months were studied. Measurements of the cricoid cartilage were made with a millimeter-graded caliper. Results: Weight was the variable most correlated with cricoid measurements. The cricoid lumen configuration showed an almost elliptic shape and did not change with gestational age. The mean inner subglottic cricoid area was 19.27 +/- 9.62 mm(2) and was related to weight and body surface area. Cricoid growth was more pronounced at the outer portion of the cartilage. Conclusions: The cricoid lumen configuration was elliptic, and its mean area was smaller than that of available endotracheal tubes. This lumen area was most influenced by weight and height.

Oocyte diameter as a predictor of fertilization and embryo quality in assisted reproduction cycles

Objective: To assess the impact of the mean oocyte diameter (MOD) on occurrence of fertilization and embryo quality in assisted reproduction cycles. Design: Prospective observational study. Setting: Sector of Human Reproduction of the University Hospital, Faculty of Medicine of Ribeirao Preto, University of Sao Paulo (HCFMRP-USP). Patient(s): Thirty-five women undergoing intracytoplasmic sperm injection (ICSI) at the University Hospital of Ribeirao Preto from May to October 2007. Intervention(s): MOD assessment. Main Outcome Measure(s): Occurrence of fertilization and qualitative embryo classification on 2nd and 3rd day after ICSI. Result(s): We divided 160 metaphase II oocytes according to MOD into groups A (MOD below the 25th percentile), B (MOD between 25th and 75th percentile), and C (MOD above the 75th percentile). There was no statistically significant association between MOD and the occurrence of fertilization or the qualitative embryo classification on days 2 and 3. There was no statistically significant difference between groups regarding number of cells or the qualitative embryo classification on days 2 and 3. Conclusion(s): The MOD of mature oocytes does not seem to be related to the occurrence of fertilization or to the developmental quality of human embryos on days 2 and 3 after ICSI. (Fertil Steril(R) 2010;93:621-5. (C)2010 by American Society for Reproductive Medicine.)

Argon ion laser and halogen lamp activation of a dark and light resin composite: microhardness after long-term storage

The objective of this study was to evaluate in vitro light activation of the nano-filled resin composite Vita shade A1 and A3 with a halogen lamp (QTH) and argon ion laser by Knoop microhardness profile. Materials and methods: Specimens of nanofilled composite resin (Z350-3 M-ESPE) Vita shade A1 and A3 were prepared with a single increment inserted in 2.0-mm-thick and 3-mm diameter disc-shaped Teflon mold. The light activation was performed with QTH for 20 s (with an intensity of approximately 1,000 mW/cm(2) and 700 mW/cm(2)) and argon ion laser for 10 s (with a power of 150 mW and 200 mW). Knoop microhardness test was performed after 24 h and 6 months. The specimens were divided into the 16 experimental groups (n = 10), according to the factors under study: photoactivation form, resin shade, and storage time. Knoop microhardness data was analyzed by a factorial ANOVA and TukeyA ` s tests at the 0.05 level of significance. Results: Argon ion laser was not able to photo-activate the darker shade of the nanofilled resin composite evaluated but when used with 200 mW it can be as effective as QTH to photo-activate the lighter shade with only 50% of the time exposure. After 6 months storage, an increase in the means of Knoop microhardness values were observed. Conclusions: Light-activation significantly influenced the Knoop microhardness values for the darker nanofilled resin composite.