Pesquisa e desenvolvimento de um sistema termoelétrico do tipo linear fresnel reflector

Dissertação para obtenção do Grau de Mestre em Energias Renováveis – Conversão Elétrica e Utilização Sustentável

Optimisation and design of post-tensioning anchorage corner blisters in concrete box girder bidges

The design of anchorage blisters of internal continuity post-tensioning tendons of bridges built by the cantilever method, presents some peculiarities, not only because they are intermediate anchorages but also because these anchorages are located in blisters, so the prestressing force has to be transferred from the blister the bottom slab and web of the girder. The high density of steel reinforcement in anchorage blisters is the most common reason for problems with concrete cast in situ, resulting in zones with low concrete compacity, leading to concrete crushing failures under the anchor plates. A solution may involve improving the concrete compression and tensile strength. To meet these requirements a high-performance fibre reinforced self-compacting mix- ture (HPFRC) was used in anchorage corner blisters of post-tensioning tendons, reducing the concrete cross-section and decreasing the reinforcement needed. To assess the ultimate capacity and the adequate serviceability of the local anchorage zone after reducing the minimum concrete cross-section and the confining reinforcement, specified by the anchorage device supplier for the particular tendon, load transfer tests were performed. To investigate the behaviour of anchorage blisters regarding the transmission of stresses to the web and the bottom slab of the girder, and the feasibility of using high performance concrete only in the blister, two half scale models of the inferior corner of a box girder existing bridge were studied: a reference specimen of ordinary reinforced concrete and a HPFRC blister specimen. The design of the reinforcement was based in the tensile forces obtained on strut-and-tie models. An experimental program was carried out to assess the models used in design and to study the feasibility of using high performance concrete only in the blister, either with casting in situ, or with precast solutions. A non-linear finite element analysis of the tested specimens was also performed and the results compared.

Estudio de las capas de acoplamiento y alternativas al reflector de Bragg en estructuras BAW-CRF

Las capas de acoplamiento son un elemento clave en los dispositivos BAW CRF. El factor de acoplamiento K de estas capas permite el diseño de una determinada respuesta. Debido al limitado número de materiales con las que implementarlas, las soluciones que utilizan capas de λ/4 ofrecen un rango discreto de K. Por otra parte, el reflector de Bragg es un mecanismo de aislamiento mecánico entre el sustrato y la estructura BAW que está formado por capas alternas de alta y baja impedancia acústica de λ/4. El problema que presenta es la reducción del factor de calidad asociado a las pérdidas producida por las ondas shear. Este proyecto presenta un método para la obtención de un rango continuo de factores de acoplamiento y estudia la mejora del factor de calidad de las estructuras BAW con reflector de Bragg partiendo de dos materiales con alta y baja impedancia acústica.

Gerdy tubercle osteotomy in surgical approach of posterolateral corner of the knee.

Posterolateral corner (PLC) injuries of the knee are uncommon injury patterns that may result in significant degrees of functional disability. When surgery is necessary to address this injury a good knowledge of anatomy and a good surgical exposure is the mainstay. This report reviews the complex anatomy of the posterolateral corner (PLC) of knee and describes the osteotomy of Gerdy tubercle as a technical variant to approach this anatomical region. This surgical step allowing a good mobilisation of the multiple layers of ilio-tibial tract from distal to proximal makes an excellent exposure of the PLC structures with absence of morbidity.

Anàlisi i disseny d'un reflector per banda W

Les ones passives mil·limètriques (30 a 300GHz) tenen la peculiaritat de propagar-se en medis com la boira o la roba, a diferència del rang visible o l’infraroig. D’aquesta peculiaritat, surt l’interès de reproduir imatges per diverses aplicacions (seguretat, vigilància, etc...). És per aquest motiu que es treballa en el disseny d’un reflector per aquest tipus d’aplicació, treballant a una de les finestres de propagació d’aquest rang, la de la banda W. Es dissenyen i analitzen tres tipus de reflector: parabòlic simètric, offset i Cassegrain. D’aquests, s’estudien les seves figures de mèrit i directivitats buscant que aquestes siguin el més elevades possibles per obtenir una bona resolució, així com l’escaneig de l’escena de la qual es vol obtenir una imatge, veient aquí els efectes de les aberracions més comunes.

Jurassic sedimentary record and tectonic evolution of the northwestern corner of Africa

The history of the opening seaway from the westernmost Tethys to the Central Atlantic is traced by the analysis of the sedimentary facies development in the external Rif basin of Northern Morocco and the geological and seismic data from the Moroccan Atlantic continental margin. In the Rif basin, after the early Sinemurian, sedimentary facies dated by ammonites, foraminifers and brachiopods, indicate a progression of rapid subsidence resulting from extensional tectonic (tilted blocks, escarpment fault breccias, neptunian dykes etc.) from the N and NE to the S and SW. From the Toarcian to the Bajocian, deltas progress from the W and SW into the `'Rides sud-rifaines'' realm. From the late Bathonian to the Oxfordian, deep-sea fans develop in the external Rif. During the same period, deltaic sediments fill in the Middle Atlas basin of Eastern Morocco and progress into the external Rif. The top of the Jurassic is characterised by carbonate deposits. At the northwestern corner of Africa, the subsidence of the sedimentary basins by rifting is initiated in the late Triassic; however, at the Mazagan transect of the Atlantic continental margin, the tectonic pattern characteristic of a passive continental margin appears clearly only in the early Jurassic. At the foot of the Mazagan escarpment, the sedimentary record shows a foundering of the first bloc during early to middle Lias. A thermal uplift phase is indicated by emersion of the African margin shoulder in late Liassic, and thermal relaxation starts in the middle Jurassic. The morphology of this transect, compared with the conjugate side of the American continent is most easily explained by the uniform sense simple shear model.

Proceedings at the Laying of the Corner Stone of the New Capitol Building at Des Moines, Iowa, November 23, 1871.

An act to provide the State of Iowa with a new state capitol building was enacted on April 14, 1870 and then on Thursday, the 23d day of November, 1871, the corner stone of the new capitol building, at the city of Des Moines, was laid with appropriate ceremonies

Four-corner bone arthrodesis with dorsal rectangular plate: series and personal technique.

Controversy exists about the best method to achieve bone fusion in four-corner arthrodesis. Thirty-five patients who underwent this procedure by our technique were included in the study. Surgical indications were stage II-III SLAC wrist, stage II SNAC wrist and severe traumatic midcarpal joint injury. Mean follow-up was 4.6 years. Mean active flexion and extension were 34 degrees and 30 degrees respectively; grip strength recovery was 79%. Radiological consolidation was achieved in all cases. The mean DASH score was 23 and the postoperative pain improvement by visual analogue scale was statistically significant. Return to work was possible at 4 months for the average patient. Complications were a capitate fracture in one patient and the need for hardware removal in four cases. Four-corner bone wrist arthrodesis by dorsal rectangular plating achieves an acceptable preservation of range of motion with good pain relief, an excellent consolidation rate and minimal complications.