Graphene from Graphite by Chemical and Physical Techniques.

Graphene is a material with extraordinary properties. Its mechanical and electrical properties are unparalleled but the difficulties in its production are hindering its breakthrough in on applications. Graphene is a two-dimensional material made entirely of carbon atoms and it is only a single atom thick. In this work, properties of graphene and graphene based materials are described, together with their common preparation techniques and related challenges. This Thesis concentrates on the topdown techniques, in which natural graphite is used as a precursor for the graphene production. Graphite consists of graphene sheets, which are stacked together tightly. In the top-down techniques various physical or chemical routes are used to overcome the forces keeping the graphene sheets together, and many of them are described in the Thesis. The most common chemical method is the oxidisation of graphite with strong oxidants, which creates a water-soluble graphene oxide. The properties of graphene oxide differ significantly from pristine graphene and, therefore, graphene oxide is often reduced to form materials collectively known as reduced graphene oxide. In the experimental part, the main focus is on the chemical and electrochemical reduction of graphene oxide. A novel chemical route using vanadium is introduced and compared to other common chemical graphene oxide reduction methods. A strong emphasis is placed on electrochemical reduction of graphene oxide in various solvents. Raman and infrared spectroscopy are both used in in situ spectroelectrochemistry to closely monitor the spectral changes during the reduction process. These in situ techniques allow the precise control over the reduction process and even small changes in the material can be detected. Graphene and few layer graphene were also prepared using a physical force to separate these materials from graphite. Special adsorbate molecules in aqueous solutions, together with sonic treatment, produce stable dispersions of graphene and few layer graphene sheets in water. This mechanical exfoliation method damages the graphene sheets considerable less than the chemical methods, although it suffers from a lower yield.

Chemical Evaluation of Selected Organics and Trace Metals in the Mangrove Macroflora Of Cochin

Mangroves are considered to play a significant role in global carbon cycling. Themangrove forests would fix CO2 by photosynthesis into mangrove lumber and thus decrease the possibility of a catastrophic series of events - global warming by atmospheric CO2, melting of the polar ice caps, and inundation of the great coastal cities of the world. The leaf litter and roots are the main contributors to mangrove sediments, though algal production and allochthonous detritus can also be trapped (Kristensen et al, 2008) by mangroves due to their high organic matter content and reducing nature are excellent metal retainers. Environmental pollution due to metals is of major concern. This is due to the basic fact that metals are not biodegradable or perishable the way most organic pollutants are. While most organic toxicants can be destroyed by combustion and converted into compounds such as C0, C02, SOX, NOX, metals can't be destroyed. At the most the valance and physical form of metals may change. Concentration of metals present naturally in air, water and soil is very low. Metals released into the environment through anthropogenic activities such as burning of fossils fuels, discharge of industrial effluents, mining, dumping of sewage etc leads to the development of higher than tolerable or toxic levels of metals in the environment leading to metal pollution. Of course, a large number of heavy metals such as Fe, Mn, Cu, Ni, Zn, Co, Cr, Mo, and V are essential to plants and animals and deficiency of these metals may lead to diseases, but at higher levels, it would lead to metal toxicity. Almost all industrial processes and urban activities involve release of at least trace quantities of half a dozen metals in different forms. Heavy metal pollution in the environment can remain dormant for a long time and surface with a vengeance. Once an area gets toxified with metals, it is almost impossible to detoxify it. The symptoms of metal toxicity are often quite similar to the symptoms of other common diseases such as respiratory problems, digestive disorders, skin diseases, hypertension, diabetes, jaundice etc making it all the more difficult to diagnose metal poisoning. For example the Minamata disease caused by mercury pollution in addition to affecting the nervous system can disturb liver function and cause diabetes and hypertension. The damage caused by heavy metals does not end up with the affected person. The harmful effects can be transferred to the person's progenies. Ironically heavy metal pollution is a direct offshoot of our increasing ability to mass produce metals and use them in all spheres of existence. Along with conventional physico- chemical methods, biosystem approachment is also being constantly used for combating metal pollution

The development of indigo reduction methods and pre-reduced indigo products

The continuing importance of blue denim maintains indigo as an important vat dye industrially. In this review, we examine the various methods that have been used in the past and are currently used to reduce and dissolve indigo for dyeing. We discuss recent insights into the bacterial fermentation technology, the advantages and disadvantages of the direct chemical methods that have predominated for the last century and potentially cleaner technologies of catalytic hydrogenation and electrochemistry, which are becoming increasingly important. With considerations of environmental impact high on the dyeing industry's agenda, we also discuss the developments that have led to the production of pre-reduced indigo.

Electroluminescence of zinc oxide thin-films prepared via polymeric precursor and via sol-gel methods

Zinc oxide (ZnO) is an electroluminescent (EL) material that can emit light in different regions of electromagnetic spectrum when electrically excited. Since ZnO is chemically stable, inexpensive and environmentally friendly material, its EL property can be useful to construct solid-state lamps for illumination or as UV emitter. We present here two wet chemical methods to prepare ZnO thin-films: the Pechini method and the sol-gel method, with both methods resulting in crystalline and transparent films with transmittance > 85% at 550 nm. These films were used to make thin-film electroluminescent devices (TFELD) using two different insulator layers: lithium fluoride (LiF) or silica (SiO2). All the devices exhibit at least two wide emission bands in the visible range centered at 420 nm and at 380 nm attributed to the electronic defects in the ZnO optical band gap. Besides these two bands, the device using SiO2 and ZnO film obtained via sol-gel exhibits an additional band in the UV range centered at 350 nm which can be attributed to excitonic emission. These emission bands of ZnO can transfer their energy when a proper dopant is present. For the devices produced the voltage-current characteristics were measured in a specific range of applied voltage. (C) 2007 Elsevier B.V. All rights reserved.

Internally contracted multireference coupled-cluster methods

This thesis details the development of quantum chemical methods for the accurate theoretical description of molecular systems with a complicated electronic structure. In simple cases, a single Slater determinant, in which the electrons occupy a number of energetically lowest molecular orbitals, offers a qualitatively correct model. The widely used coupled-cluster method CCSD(T) efficiently includes electron correlation effects starting from this determinant and provides reaction energies in error by only a few kJ/mol. However, the method often fails when several electronic configurations are important, as, for instance, in the course of many chemical reactions or in transition metal compounds. Internally contracted multireference coupled-cluster methods (ic-MRCC methods) cure this deficiency by using a linear combination of determinants as a reference function. Despite their theoretical elegance, the ic-MRCC equations involve thousands of terms and are therefore derived by the computer. Calculations of energy surfaces of BeH2, HF, LiF, H2O, N2 and Be3 unveil the theory's high accuracy compared to other approaches and the quality of various hierarchies of approximations. New theoretical advances include size-extensive techniques for removing linear dependencies in the ic-MRCC equations and a multireference analog of CCSD(T). Applications of the latter method to O3, Ni2O2, benzynes, C6H7NO and Cr2 underscore its potential to become a new standard method in quantum chemistry.

Planktological-chemical observation during the International Indian Ocean Expedition (IIOE) with RV "Meteor" in 1964/65

The present volume contains the planktological data collected during the expedition of the "Meteor" to the Indian Ocean in 1964/65. It was the main objective of the expedition to study the up- and downwelling conditioned along the western and eastern coasts of the Arabian Sea by the northeastern monsoon. It is from these areas that the greater part of the data here presented was obtained. A few values from the Red Sea have been added. As the title "Planktological-Chemical Data" implies, it was chiefly with the help of chemical methods that the planktological investigations, with the exception of the particle size analysis and phytoplankton counting conducted optically, were carried out. These investigations were above all devoted to a quantitative survey of particulate matter and plankton, the latter being sampled by water-bottle and net. The zooplankton hauls were taken with the Indian Ocean Standard Net according to the international guidelines laid down for the expedition. As a rule, double catches were made at every station, one sample being intended for laboratory analysis at the Indian Ocean Biological Centre in Ernakulam, South India, and the other for the Institut für Meereskunde in Kiel. In addition to determining the standing stock, the production rate of phytoplankton was measured by the 14C method. These experiments were mainly conducted during the latter half of the expedition. The planktological studies primarily covered the euphotic zone, extending into the underlying water layers up to a depth of 600 m. The investigations were above all directed towards ascertaining the quantity of organic substance, formed by primary production, in its relation to environmental conditions and determining whether or not organic substance is actively transported from the surface into the deeper layers by the periodically migration organisms of the deep scattering layers. Depending on the station time available, a few samples could now and then be taken from deeper layers. The present volume of planktological-chemical data addresses itself to all those concerned processing the extensive material collected during the International Indian Ocean Expedition. As a readily accessible work of reference, it hopes to serve as an aid in the evaluation and interpretation of the expedition results. The complementary ecological data such as temperature, salinity, and oxygen content as well as the figures obtained on abundance and distribution in depth of the nutrients essential for primary production may be found in the volume of physical-chemical data published in Series A of the "Meteor"-Forschungsergebnisse No. 2, 1966 (Dietrich et al., 1966).

The Hitch case - saving ampoules for a defendant from a chemical test for alcoholic intoxication. Final report.

National Highway Traffic Safety Administration, Office of Driver and Pedestrian Programs, Washington, D.C.

Chemical Stabilization and Physicochemical Properties of Soils, HR-97, Special Report, 1966

This project was initiated to gain a better understanding of the phenomena which affect the engineering behavior of soils containing colloidal size particles and to find chemical methods of treatment which could improve the engineering performance of such soils.

Chemical Stabilization and Physicochemical Properties of Soils, HR-97, Final Report, 1966

This project was initiated to gain a better understanding of the phenomena which affect the engineering behavior of soils containing colloidal size particles and to find chemical methods of treatment which could improve the engineering performance of such soils.

Breaking Oil-in-water Emulsions Stabilized By Yeast.

Several biotechnological processes can show an undesirable formation of emulsions making difficult phase separation and product recovery. The breakup of oil-in-water emulsions stabilized by yeast was studied using different physical and chemical methods. These emulsions were composed by deionized water, hexadecane and commercial yeast (Saccharomyces cerevisiae). The stability of the emulsions was evaluated varying the yeast concentration from 7.47 to 22.11% (w/w) and the phases obtained after gravity separation were evaluated on chemical composition, droplet size distribution, rheological behavior and optical microscopy. The cream phase showed kinetic stability attributed to mechanisms as electrostatic repulsion between the droplets, a possible Pickering-type stabilization and the viscoelastic properties of the concentrated emulsion. Oil recovery from cream phase was performed using gravity separation, centrifugation, heating and addition of demulsifier agents (alcohols and magnetic nanoparticles). Long centrifugation time and high centrifugal forces (2h/150,000×g) were necessary to obtain a complete oil recovery. The heat treatment (60°C) was not enough to promote a satisfactory oil separation. Addition of alcohols followed by centrifugation enhanced oil recovery: butanol addition allowed almost complete phase separation of the emulsion while ethanol addition resulted in 84% of oil recovery. Implementation of this method, however, would require additional steps for solvent separation. Addition of charged magnetic nanoparticles was effective by interacting electrostatically with the interface, resulting in emulsion destabilization under a magnetic field. This method reached almost 96% of oil recovery and it was potentially advantageous since no additional steps might be necessary for further purifying the recovered oil.

DFT and electrochemical studies on nortriptyline oxidation sites

A study on the possible sites of oxidation and epoxidation of nortriptyline was performed using electrochemical and quantum chemical methods; these sites are involved in the biological responses (for example, hepatotoxicity) of nortriptyline and other similar antidepressants. Quantum chemical studies and electrochemical experiments demonstrated that the oxidation and epoxidation sites are located on the apolar region of nortriptyline, which will useful for understanding the molecule`s activity. Also, for the determination of the compound in biological fluids or in pharmaceutical formulations, we propose a useful analytical methodology using a graphite-polyurethane composite electrode, which exhibited the best performance when compared with boron-doped diamond or glassy carbon surfaces.

Flyash as support for Ni catalysts in carbon dioxide reforming of methane

A series of Ni catalysts supported on flyash treated by various chemical methods was tested for carbon dioxide reforming of methane. Ni catalyst on the flyash treated with CaO (Ni/Ash-CaO) shows high conversion and stability, being close to those of the well-reported Ni/Al2O3 and Ni/SiO2 catalysts with conversions approaching thermodynamic equilibrium levels.

Degradation of phenanthrene and pyrene in soil slurry reactors with immobilized bacteria Zoogloea sp.

The environmental fate of polycyclic aromatic hydrocarbons (PAHs) in soils is motivated by their wide distribution, high persistence, and potentially deleterious effect on human health. Polycyclic aromatic hydrocarbons constitute the largest group of environmental contaminants released in the environment. Therefore, the potential biodegradation of these compounds is of vital importance. A biocarrier suitable for the colonization by micro-organisms for the purpose of purifying soil contaminated by polycyclic aromatic hydrocarbons was developed. The optimized composition of the biocarrier was polyvinyl alcohol (PVA) 10%, sodium alginate (SA) 0.5%, and powdered activated carbon (PAC) 5%. There was no observable cytotoxicity of biocarriers on immobilized cells and a viable cell population of 1.86 x 10(10) g(-1) was maintained for immobilized bacterium. Biocarriers made from chemical methods had a higher biodegradation but lower mechanical strengths. Immobilized bacterium Zoogloea sp. had an ideal capability of biodegradation for phenanthrene and pyrene over a relative wide concentration range. The study results showed that the biodegradation of phenanthrene and pyrene reached 87.0 and 75.4%, respectively, by using the optimal immobilized method of Zoogloea sp. cultivated in a sterilized soil. Immobilized Zoogloea sp. was found to be effective for biodegrading the soil contaminated with phenanthrene and pyrene. Even in natural (unsterilized) soil, the biodegradation of phenanthrene and pyrene using immobilized Zoogloea sp. reached 85.0 and 67.1%, respectively, after 168 h of cultivation, more than twice that achieved if the cells were not immobilized on the biocarrier. Therefore, the immobilization technology enhanced the competitive ability of introduced micro-organisms and represents an effective method for the biotreatment of soil contaminated with phenanthrene and pyrene.

Estudo do potencial antioxidante de vegetais em produção aquapónica

Dissertação de Mestrado, Tecnologia e Segurança Alimentar, 14 de Dezembro de 2015, Universidade dos Açores.

Mechanism of extracellular silver nanoparticles synthesis by Stereum hirsutum and Fusarium oxysporum

The increasing interest for greener and biological methods of synthesis has led to the development of non-toxic and comparatively more bioactive nanoparticles. Unlike physical and chemical methods of nanoparticle synthesis, microbial synthesis in general and mycosynthesis in particular is cost-effective and environment-friendly. However, different aspects, such as the rate of synthesis, monodispersity and downstream processing, need to be improved. Many fungal-based mechanisms have been proposed for the formation of silver nanoparticles (AgNPs), mainly those involving the presence of nitrate reductase, which has been detected in filtered fungus cell used for AgNPs production. There is a general acceptance that nitrate reductase is the main responsible for the reduction of Ag ions for the formation of AgNPs. However, this generally accepted mechanism for fungal AgNPs production is not totally understood. In order to elucidate the molecules participating in the mechanistic formation of metal nanoparticles, the current study is focused on the enzymes and other organic compounds involved in the biosynthesis of AgNPs. The use of each free fungal mycelium of both Stereum hirsutum and Fusarium oxysporum will be assessed. In order to identify defective mutants on the nitrate reductase structural gene niaD, fungal cultures of S.hirsutum and F.oxysporum will be selected by chlorate resistance. In addition, in order to verify if each compound identified as key-molecule influenced on the production of nanoparticles, an in vitro assay using different nitrogen sources will be developed. Lately, fungal extracellular enzymes will be measured and an in vitro assay will be done. Finally, The nanoparticle formation and its characterization will be evaluated by UV-visible spectroscopy, electron microscopy (TEM), X-ray diffraction analysis (XRD), Fourier transforms infrared spectroscopy (FTIR), and LC-MS/MS.