Transcriptional changes in U343 MG-a glioblastoma cell line exposed to ionizing radiation

Glioblastoma multiforme (GBM) is a highly invasive and radioresistant brain tumor. Aiming to study how glioma cells respond to gamma-rays in terms of biological processes involved in cellular responses, we performed experiments at cellular context and gene expression analysis in U343-MG-a GBM cells irradiated with 1 Gy and collected at 6 h post-irradiation. The survival rate was approximately 61% for 1 Gy and was completely reduced at 16 Gy. By performing the microarray technique, 859 cDNA clones were analyzed. The Significance Analysis of Microarray algorithm indicated 196 significant expressed genes (false discovery rate (FDR) = 0.42%): 67 down-regulated and 97 up-regulated genes, which belong to several classes: metabolism, adhesion/cytoskeleton, signal transduction, cell cycle/apoptosis, membrane transport, DNA repair/DNA damage signaling, transcription factor, intracellular signaling, and RNA processing. Differential expression patterns of five selected genes (HSPA9B, INPP5A, PIP5K1A, FANCG, and TPP2) observed by the microarray analysis were further confirmed by the quantitative real time RT-PCR method, which demonstrated an up-regulation status of those genes. These results indicate a broad spectrum of biological processes (which may reflect the radio-resistance of U343 cells) that were altered in irradiated glioma cells, so as to guarantee cell survival.

Eutectic solidification mode in sodium modified Al-7 mass %Si-3.5 mass %Cu-0.2 mass %Mg casting alloys

The influence of sodium (Na) on nucleation and growth of the Al-Si eutectic in a commercial hypoeutectic Al-Si-Cu-Mg foundry alloy has been investigated. The microstructural evolution during eutectic solidification was studied by a quenching technique. By comparing the orientation of the aluminium in the eutectic to that of the surrounding primary aluminium dendrites by EBSD, the eutectic solidification mode could be determined. The results show that the eutectic solidification starts near the mould wall and evolves with front growth opposite the thermal gradient on a macro-scale, and on a micro-scale with independent heterogeneous nucleation of eutectic grains in interdendritic spaces. Na-modified alloys therefore behave significantly differently from those modified by other elemental additions.

The effect of trace elements on the sintering of an Al-Zn-Mg-Cu alloy

Trace elements can have a significant effect on the processing and properties of aluminium alloys, including sintered alloys. As little as 0.07 wt% (100 ppm) lead, tin or indium promotes sintering in an Al-Zn-Mg-Cu alloy produced from mixed elemental powders. This is a liquid phase sintering system and thin liquid films form uniformly throughout the alloy in the presence of the trace elements, but liquid pools develop in their absence. Analytical transmission electron microscopy indicates that the trace elements are confined to the interparticle and grain boundary regions. The sintering enhancement is attributed to the segregation of the microalloying addition to the liquid-vapour interface. Because the microalloying elements have a low surface tension, they lower the effective surface tension of the liquid. This reduces the wetting angle and extends the spreading of the liquid through the matrix. An improvement in sintering results. (C) 2001 Acta Materialia Inc. Published by Elsevier Science Ltd. All rights reserved.

Mass balance characterisation of Al-7Si-Mg alloy microstructures as a function of solution treatment time

Mass balance calculations were performed to model the effect of solution treatment time on A356 and A357 alloy microstructures. Image analysis and electron probe microanalysis were used to characterise microstructures and confirm model predictions. In as-cast microstructures, up to 8 times more Mg is tied up in the pi-phase than in Mg2Si. The dissolution of pi is accompanied by a corresponding increase in the amount of beta-phase. This causes the rate of pi dissolution to be limited by the rate of beta formation. It is predicted that solution treatments of the order of tens of minutes at 540degreesC produce near-maximum T6 yield strengths, and that Mg contents in excess of 0.52 wt% have no advantage.

An age hardening model for Al-7Si-Mg casting alloys

Yield strength (YS) ageing curves have been modelled for A356 and A357 aluminium casting alloys below the solvus temperature of the main hardening precipitate. Predictions are based on the Shercliff and Ashby methodology (Acta MetaH. Mater. 38 (1990) 1789) for wrought alloys. Differences between strengthening in wrought and cast Al-Si-Mg alloys are considered. A Brinell hardness to YS conversion incorporating strain hardening has been established to enable YS ageing curves to be predicted with reduced experimental effort. (C) 2002 Elsevier Science B.V. All rights reserved.

Characteristic zirconium-rich coring structures in Mg-Zr alloys

The most characteristic feature of the microstructure of a magnesium alloy that contains more than a few tenths per cent soluble zirconium is the zirconium-rich cores that exist in most grains. The morphology, distribution and composition of cores observed in a Mg-0.56%Zr alloy and the small particles present in them were investigated. (C) 2002 Acta Materialia Inc. Published by Elsevier Science Ltd. All rights reserved.

The strength of concentrated Mg-Zn solid solutions

Solid solution effects on the hardness and flow stress have been studied for zinc contents between 0.2 and 2.4 at% (0.5 and 6.9 wt%) in Mg. The alloys were grain refined with 0.6 wt% zirconium to ensure a similar grain size at all compositions. The hardness increases with the zinc content as Hv(10) (kg mm(-2)) = 9 Zn (at%) + 33. At low solute concentrations the (0.2%) proof strength does not change significantly with concentration. At concentrations above 0.7 at%, within the supersaturated solid solution region, the rate of solid solution hardening is high, following a c(2) rule, where c is the atom fraction of Zn. It is suggested that short-range order may account for most of the observed strengthening in concentrated Mg-Zn alloys.

O papel da cidade de Viçosa-MG na rede urbana : a especialização funcional de uma cidade média mineira

Rede é o nome dado para se referenciar qualquer forma que seja composta por linhas interligadas por pontos, sendo assim essa denominação é utilizada para participar de nomes e conceitos em diversas área do conhecimento. Na geografia isso não ocorre de forma diferente. As redes geográficas são a denominação dada as ligações feitas no espaço articuladas por pontos, notadamente são usadas para se fazer referência a redes materiais, mas podem ser mais imateriais ou abstratas a depender do objeto de pesquisa e do adjetivo adotado. A noção de redes urbanas nasceu vinculada aos objetos materiais, entretanto com a evolução da técnica passou a abranger objetos cada vez mais virtuais. As redes urbanas são compostas pelo conjunto de cidades, cada qual com sua centralidade representadas por pontos ou nós na rede, e pelas ligações entre elas, rodovias, hidrovias, infovias etc. As cidades que compõem a rede, por mais semelhanças que possam ter entre si, tem diferentes tipos e graus de centralidade, de poder de atração de pessoas, de recursos; sendo uma região de influência singular, que muda de tempos em tempos, face a evolução do território onde se insere. Tanto as centralidades quanto as redes de urbanas estão em constante mudança, necessitando sempre de atualização tornando o estudo das redes e das centralidades uma questão sempre nova; em especial quando considerado um território tão vasto e complexo como o brasileiro. Neste trabalho relatamos os resultados do estudo das especificidades da centralidade da cidade de Viçosa, que está localizada no interior do estado de Minas Gerais, Brasil. Este estudo fez uso de dados numéricos, fotográficos e cartográficos coletados em diversos momentos da evolução do município e da região onde este se insere, que revelaram as mudanças de qualidade e de intensidade na centralidade dessa cidade, hoje tipificada como média ou intermediária, inserida na rede urbana mineira. No período compreendido entre os anos de 1850 e 1930, Viçosa passou de uma inexpressiva localidade rural, a importante centro de produção de café, galgando ganhos políticos nesse período. Seguiu-se um período de menor pujança, por cerca de setenta anos, para depois, na virada do século XX para XXI, ressurgi como uma localidade especializada em oferecer serviços, notadamente vinculados ao ensino superior e à produção de ciência e tecnologia. Essa nova centralidade, ao contrário do que muitas vezes ocorre, não foi fruto nem de um recurso natural inerente ao território e nem, tão pouco, pela atuação de grandes grupos capitalistas. Foi galgado principalmente pela atuação do Estado que construiu ali as bases de uma especialização funcional, através da implantação de uma universidade pública.