Calcários albianos de campo petrolífero na Bacia de Campos: fácies, diagênese e modelo deposicional

Pós-graduação em Geologia Regional - IGCE

Modelo deposicional de carbonatos albianos da Formação Quissamã: análise faciológica, diagenética e estratigráfica de um campo de óleo na porção meridional da Bacia de Campos

Pós-graduação em Geologia Regional - IGCE

Caracterização da distribuição física dos dolomitos do membro Búzios no Campo de Badejo - Bacia de Campos

In the region of Badejo oil Ffeld (Campos Basin) lies an Lower Albian dolomitic layer that shows reservoir rock and seal conditions, among others and, it is occasionally karstified. This work applies geostatistical techniques of ordinary and indicatior kriging, in an attempt to determine a method that assists the analysis of different scenarios offered for petroleum drilling from a quantitative point of view this fact is justified, because there are different visions and strategies that would be adopted under different dolomite conditions (stable - low porosity and high density; reservoir - high porosity and medium density; instable - high porosity and low dentisty). The main objective is a methodological introduction that has not been tested in dolomites before aiming to characterize the distribution of the three conditions described above by ordinary and indicatior kriging, which was based on the obtained data from the dolomite layer identification through well logs interpretation and correlation, followed by seismic interpretation. In addition, it was generated structural contour maps, based on 2D and 3D seismic data interpretation, and then, seismic attributes maps were calculated, in order to transform them into pseudo-density maps, i.e., maps that correlate the density values with the attribute values. As primary results, structural contour maps and seismic attributes were obtained and ordinary and indicatior kriging maps were done, on which it is possible to interpret the distribution of the main reservoir and risk probability for drilling of exploration wells obtaining trends N35E and N10W direction for areas of stability or reservoir levels, while the central part of the map presents a higher risk for loss of drilling fluid. The cut-off values levels were based on the values of first and third quartiles of cumulative histogram (instable and stable zones, respectively), as well as the reservoir level was set as the interval...

Análise paleopalinológica do Albiano (Cretáceo inferior) da Bacia de Campos, com ênfase no estudo de dinoflagelados

Pós-graduação em Geociências e Meio Ambiente - IGCE

The Oligocene-Neogene deep-sea Columbia Channel system in the South Brazilian Basin: Seismic stratigraphy and environmental changes

The Columbia Channel (CCS) system is a depositional system located in the South Brazilian Basin, south of the Vitoria-Trindade volcanic chain. It lies in a WNW-ESE direction on the continental rise and abyssal plain, at a depth of between 4200 and 5200 m. It is formed by two depocenters elongated respectively south and north of the channel that show different sediment patterns. The area is swept by a deep western boundary current formed by AABW. The system has been previously interpreted has a mixed turbidite-contourite system. More detailed study of seismic data permits a more precise definition of the modern channel morphology, the system stratigraphy as well as the sedimentary processes and control. The modern CCS presents active erosion and/or transport along the channel. The ancient Oligo-Neogene system overlies a ""upper Cretaceous-Paleogene"" sedimentary substratum (Unit U1) bounded at the top by a major erosive ""late Eocene-early Oligocene"" discordance (D2). This ancient system is subdivided into 2 seismic units (U2 and U3). The thick basal U2 unit constitutes the larger part of the system. It consists of three subunits bounded by unconformities: D3 (""Oligocene-Miocene boundary""), D4 (""late Miocene"") and D5 (""late Pliocene""). The subunits have a fairly tabular geometry in the shallow NW depocenter associated with predominant turbidite deposits. They present a mounded shape in the deep NE depocenter, and are interpreted as forming a contourite drift. South of the channel, the deposits are interpreted as a contourite sheet drift. The surficial U3 unit forms a thin carpet of deposits. The beginning of the channel occurs at the end of U1 and during the formation of D2. Its location seems to have been determined by active faults. The channel has been active throughout the late Oligocene and Neogene and its depth increased continuously as a consequence of erosion of the channel floor and deposit aggradation along its margins. Such a mixed turbidite-contourite system (or fan drift) is characterized by frequent, rapid lateral facies variations and by unconformities that cross the whole system and are associated with increased AABW circulation. (C) 2009 Elsevier B.V. All rights reserved.

Correlações nos dfa de diversos perfis geológicos. estudo de caso: Bacia de Campos - RJ

This work aims to study the fluctuation structure of physical properties of oil well profiles. It was used as technique the analysis of fluctuations without trend (Detrended Fluctuation Analysis - DFA). It has been made part of the study 54 oil wells in the Campo de Namorado located in the Campos Basin in Rio de Janeiro. We studied five sections, namely: sonic, density, porosity, resistivity and gamma rays. For most of the profiles , DFA analysis was available in the literature, though the sonic perfile was estimated with the aid of a standard algorithm. The comparison between the exponents of DFA of the five profiles was performed using linear correlation of variables, so we had 10 comparisons of profiles. Our null hypothesis is that the values of DFA for the various physical properties are independent. The main result indicates that no refutation of the null hypothesis. That is, the fluctuations observed by DFA in the profiles do not have a universal character, that is, in general the quantities display a floating structure of their own. From the ten correlations studied only the profiles of density and sonic one showed a significant correlation (p> 0.05). Finally these results indicate that one should use the data from DFA with caution, because, in general, based on geological analysis DFA different profiles can lead to disparate conclusions

Effects of drill cuttings discharge on meiofauna communities of a shelf break site in the southwest Atlantic

The present study investigates the effects of drill cutting discharges on the structure of meiofauna communities in an area of the shelf break at Campos Basin, Southeast Brazil. Drilling activities were operated, in a first phase, with water-based fluid and, in a second phase, with synthetic fluid paraffin-based (NAF-III). A total of 135 samples taken at a pre-drilling situation (MS1) and two post-drilling moments (MS2 and MS3-3 and 22 months post-drilling, respectively) were analyzed. Effects on meiofauna were dependent on two main factors: 1-the impact received during drilling operation, if water-based or synthetic/water-based drilling fluid and 2-the background state, if it already presented signs of previous drilling activities or not. Based on univariate and multivariate analysis, there were evidences that the most affected area after drilling was those under the influence of synthetic-based fluid and that already had signs of previous drillings activities. The region impacted only by water-based fluid was less affected and the only one that completely recovered after 22 months. Nematodes and copepods had different responses to the impact. While copepods flourish in the impacted area and recovered 22 months after drilling, nematodes were adversely affected shortly after drilling and the community structure only recovered where hydrocarbons had been depleted.

Directional Wave Spectrum Estimation Based on Vessel`s 1st-order Motions: Field Results

In this paper, 2 different approaches for estimating the directional wave spectrum based on a vessel`s 1st-order motions are discussed, and their predictions are compared to those provided by a wave buoy. The real-scale data were obtained in an extensive monitoring campaign based on an FPSO unit operating at Campos Basin, Brazil. Data included vessel motions, heading and tank loadings. Wave field information was obtained by means of a heave-pitch-roll buoy installed in the vicinity of the unit. `two of the methods most widely used for this kind of analysis are considered, one based on Bayesian statistical inference, the other consisting of a parametrical representation of the wave spectrum. The performance of both methods is compared, and their sensitivity to input parameters is discussed. This analysis complements a set of previous validations based on numerical and towing-tank results and allows for a preliminary evaluation of reliability when applying the methodology at full scale.

Determinação de fósforo orgânico em águas de produção petrolífera por ICP- AES e ICP- MS após pré-concentração em coluna de sílica-C18

Results on the optimization of analytical methods for the determination of phosphorus in phosphino-polycarboxylate (PPCA), used frequently as scale inhibitor during oil production, by ICP-AES and ICP-MS are presented. Due to the complex matrix of production waters (brines) and their high concentration in inorganic phosphorus, the separation of organic phosphorus prior to its determination is necessary. In this work, minicolumns of silica immobilized C18 were used. Optimization of the separation step resulted in the following working conditions: (1) prewashing of the column with methanol (80% v/v); (2) use of a flow rate of 5 mL/min and 10 mL/min, respectively, for the preconditioning step and for percolation of the water sample; (3) final elution of organic phosphorus with 7 mL of buffer of H3BO3/NaOH (0.05 M, pH 9) with a flow rate of 1 mL/min. Sample detection limits (3s) for different combinations of nebulizers and spectrometric methods, based on 10 mL water aliquots, are: ICP-AES -Cross flow (47 mg/L) and Ultrasonic (18 mug/L); ICP-MS -Cross flow (1.2 mug/L), Cyclonic (0.7 mug/L) and Ultrasonic (0.5 mug/L). Typical recoveries of organic phosphorus are between 90 and 95% and the repeatability of the whole procedure is better than 10%. The developed methodology was applied successfully to samples from the oil-well NA 46, platform PNA 2, Campos basin, Brazil. Assessment of the PPCA inhibitor was possible at lower concentrations than achieved by current analytical methods, resulting in benefits such as reduced cost of chemicals, postponed oil production and lower environmental impacts.

Remoção do íon amônio de águas produzidas na exploração de petróleo em áreas offshore por adsorção em clinoptilolita

This work describes the use of clinoptilolite for removal of ammonium ions present in waters produced at the Campos' Basin. Samples were previously treated in order to remove organic compounds and metals. Experiments were run in fixed- and fluidized-bed systems, at room temperature. The fluidized-bed systems did not remove efficiently the ammonium ion. The best operational conditions were obtained with clinoptilolite particle size in the range 0.30-0.50 mm, under ascendant flow (3 mL min-1), in a fixed-bed system. The best zeolite performance was found when it was pretreated with 0.5 mol L-1 NaOH. Na+ was the most important interfering ion due to its high concentration in the water. Clinoptilolite lost partially its capacity to retain ammonium ions after several regeneration cycles with NaOH.

Identification of lift-off mechanism failure for salt drill-in drilling fluid containing polymer filter cake through adsorption/desorption studies

Drilling fluid`s contact with the productive zone of horizontal or complex wells can reduce well productivity by fluid invasion in the borehole wall. Salted drilling drill-in fluid containing polymers has often been applied in horizontal or complex petroleum wells in the poorly consolidated sandstone reservoirs of the Campos basin, Rio de Janeiro, Brazil. This fluid usually consists of natural polymers such as starch and xanthan gum, which are deposited as a filter cake on the wellbore wall during the drilling. Therefore, the identification of a lift-off mechanism failure, which can be detachment or blistering and pinholing, will enable formulation improvements. increasing the chances of success during filter cake removal in open hole operations. Likewise, knowledge of drill-in drilling fluid adsorption/desorption onto sand can help understand the filter cake-rock adhesion mechanism and consequently filter cake lift-off mechanism failures. The present study aimed to identify the lift-off failure mechanism for this type of fluid filter cake studying adsorption/desorption onto SiO(2) using solutions of natural polymers, lubricants, besides the fluid itself. Ellipsometry was employed to measure this process. The adsorption/desorption studies showed that the adsorbed layer of drilling fluid onto the walls of the rock pores is made up of clusters of polymers, linked by hydrogen bonds, which results in a force of lower cohesion compared to the electrostatic interaction between silica and polymers. Consequently, it was found that the most probable filter cake failure mechanism is rupture (blistering and pinholing), which results in the formation of ducts within the filter cake. (C) 2009 Elsevier B.V. All rights reserved.

A evolução das receitas provenientes dos royalties do petróleo e seus impactos na arrecadação dos tributos de competência municipal (2002 – 2007): o caso do município de Cabo Frio/RJ

Há cerca de dez anos os municípios confrontantes com a Bacia de Campos vem registrando contínuo e vigoroso aumento das receitas oriundas das participações governamentais incidentes sobre a exploração e produção de petróleo e gás natural em função da Lei Federal n° 9.478/98 que, entre outras medidas, ampliou as alíquotas básicas de royalties de 5% para até 10% do valor da produção bem como instituiu o pagamento de participações especiais sobre o lucro obtido em campos de grande produção ou rentabilidade. Nesse trabalho buscamos analisar o comportamento, na Prefeitura Municipal de Cabo Frio, das receitas em epígrafe durante o período compreendido entre os exercícios financeiros de 2002 a 2007, verificando os efeitos quantitativos produzidos nos tributos arrecadados por aquele Executivo, bem como avaliando as gestões, através da análise dos dados coletados, no sentido de determinar em qual delas houve maior efetividade na arrecadação tributária. O estudo em tela pretende ser uma fonte de informações para futuros gestores, auxiliando-os na condução de políticas fiscais e administrativas que visem incrementar a arrecadação.

DFA e análise de agrupamento aplicadas a perfis de porosidade neutrônico em poços de petróleo

Peng was the first to work with the Technical DFA (Detrended Fluctuation Analysis), a tool capable of detecting auto-long-range correlation in time series with non-stationary. In this study, the technique of DFA is used to obtain the Hurst exponent (H) profile of the electric neutron porosity of the 52 oil wells in Namorado Field, located in the Campos Basin -Brazil. The purpose is to know if the Hurst exponent can be used to characterize spatial distribution of wells. Thus, we verify that the wells that have close values of H are spatially close together. In this work we used the method of hierarchical clustering and non-hierarchical clustering method (the k-mean method). Then compare the two methods to see which of the two provides the best result. From this, was the parameter � (index neighborhood) which checks whether a data set generated by the k- average method, or at random, so in fact spatial patterns. High values of � indicate that the data are aggregated, while low values of � indicate that the data are scattered (no spatial correlation). Using the Monte Carlo method showed that combined data show a random distribution of � below the empirical value. So the empirical evidence of H obtained from 52 wells are grouped geographically. By passing the data of standard curves with the results obtained by the k-mean, confirming that it is effective to correlate well in spatial distribution

Determinação da distribuição de um nível de turbidito na formação Macaé no campo de Namorado através de uso de atributos sísmicos

This study was developed on the basis of petrophysics characterization, 3D seismic interpretation, and rock-wire-log integration. The results were integrated with amplitude attribute through cross plot (rock attribute x amplitude value). 3D seismic data also allowed inteipreting the top of Lagoa Feia, Macaé, and Carapebus formations, and Outeiro Member. The analyses of the maps of structures and attributes, integrated with wire-log data, suggest that Namorado turbidite level is candidate to be mapped with stratigraphic attributes like AverageTroughAmplitude, RMS velocity and Total AbsoluteAmplitude. Lagoa Feia Formation attribute maps (Dip-Azimuth and TotalEnergy) allows to interpret a low fault density at the carbonate coquina level in the Namorado field. This level is also considered one at the best seismic reflector and an important reservoir of the Campos Basin.

Análise estratigráfica dos reservatórios turbidíticos do Campo de Namorado

Pós-graduação em Geologia Regional - IGCE