Nonlinear seismic behaviour of concrete arch bridges

Arch bridge structural solution has been known for centuries, in fact the simple nature of arch that require low tension and shear strength was an advantage as the simple materials like stone and brick were the only option back in ancient centuries. By the pass of time especially after industrial revolution, the new materials were adopted in construction of arch bridges to reach longer spans. Nowadays one long span arch bridge is made of steel, concrete or combination of these two as "CFST", as the result of using these high strength materials, very long spans can be achieved. The current record for longest arch belongs to Chaotianmen bridge over Yangtze river in China with 552 meters span made of steel and the longest reinforced concrete type is Wanxian bridge which also cross the Yangtze river through a 420 meters span. Today the designer is no longer limited by span length as long as arch bridge is the most applicable solution among other approaches, i.e. cable stayed and suspended bridges are more reasonable if very long span is desired. Like any super structure, the economical and architectural aspects in construction of a bridge is extremely important, in other words, as a narrower bridge has better appearance, it also require smaller volume of material which make the design more economical. Design of such bridge, beside the high strength materials, requires precise structural analysis approaches capable of integrating the combination of material behaviour and complex geometry of structure and various types of loads which may be applied to bridge during its service life. Depend on the design strategy, analysis may only evaluates the linear elastic behaviour of structure or consider the nonlinear properties as well. Although most of structures in the past were designed to act in their elastic range, the rapid increase in computational capacity allow us to consider different sources of nonlinearities in order to achieve a more realistic evaluations where the dynamic behaviour of bridge is important especially in seismic zones where large movements may occur or structure experience P - _ effect during the earthquake. The above mentioned type of analysis is computationally expensive and very time consuming. In recent years, several methods were proposed in order to resolve this problem. Discussion of recent developments on these methods and their application on long span concrete arch bridges is the main goal of this research. Accordingly available long span concrete arch bridges have been studied to gather the critical information about their geometrical aspects and properties of their materials. Based on concluded information, several concrete arch bridges were designed for further studies. The main span of these bridges range from 100 to 400 meters. The Structural analysis methods implemented in in this study are as following: Elastic Analysis: Direct Response History Analysis (DRHA): This method solves the direct equation of motion over time history of applied acceleration or imposed load in linear elastic range. Modal Response History Analysis (MRHA): Similar to DRHA, this method is also based on time history, but the equation of motion is simplified to single degree of freedom system and calculates the response of each mode independently. Performing this analysis require less time than DRHA. Modal Response Spectrum Analysis (MRSA): As it is obvious from its name, this method calculates the peak response of structure for each mode and combine them using modal combination rules based on the introduced spectra of ground motion. This method is expected to be fastest among Elastic analysis. Inelastic Analysis: Nonlinear Response History Analysis (NL-RHA): The most accurate strategy to address significant nonlinearities in structural dynamics is undoubtedly the nonlinear response history analysis which is similar to DRHA but extended to inelastic range by updating the stiffness matrix for every iteration. This onerous task, clearly increase the computational cost especially for unsymmetrical buildings that requires to be analyzed in a full 3D model for taking the torsional effects in to consideration. Modal Pushover Analysis (MPA): The Modal Pushover Analysis is basically the MRHA but extended to inelastic stage. After all, the MRHA cannot solve the system of dynamics because the resisting force fs(u; u_ ) is unknown for inelastic stage. The solution of MPA for this obstacle is using the previously recorded fs to evaluate system of dynamics. Extended Modal Pushover Analysis (EMPA): Expanded Modal pushover is a one of very recent proposed methods which evaluates response of structure under multi-directional excitation using the modal pushover analysis strategy. In one specific mode,the original pushover neglect the contribution of the directions different than characteristic one, this is reasonable in regular symmetric building but a structure with complex shape like long span arch bridges may go through strong modal coupling. This method intend to consider modal coupling while it take same time of computation as MPA. Coupled Nonlinear Static Pushover Analysis (CNSP): The EMPA includes the contribution of non-characteristic direction to the formal MPA procedure. However the static pushovers in EMPA are performed individually for every mode, accordingly the resulted values from different modes can be combined but this is only valid in elastic phase; as soon as any element in structure starts yielding the neutral axis of that section is no longer fixed for both response during the earthquake, meaning the longitudinal deflection unavoidably affect the transverse one or vice versa. To overcome this drawback, the CNSP suggests executing pushover analysis for governing modes of each direction at the same time. This strategy is estimated to be more accurate than MPA and EMPA, moreover the calculation time is reduced because only one pushover analysis is required. Regardless of the strategy, the accuracy of structural analysis is highly dependent on modelling and numerical integration approaches used in evaluation of each method. Therefore the widely used Finite Element Method is implemented in process of all analysis performed in this research. In order to address the study, chapter 2, starts with gathered information about constructed long span arch bridges, this chapter continuous with geometrical and material definition of new models. Chapter 3 provides the detailed information about structural analysis strategies; furthermore the step by step description of procedure of all methods is available in Appendix A. The document ends with the description of results and conclusion of chapter 4.

Avaliação em tempo real de forças em cabos

Dissertação elaborada para a obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Estruturas

Aplicación de la técnica de inyección del terreno por fracturación hidráulica a las cimentaciones de puentes en circunstancias de especial dificultad

La implantación de una gran obra de paso facilita en multitud de ocasiones la vida de aquellos que aprovechen las ventajas que ofrece esta estructura. Sin embargo, el camino que lleva a su construcción supone importantes y tortuosos retos cuando el terreno de cimentación presenta condiciones geotécnicas no compatibles con las grandes cargas que el viaducto necesita transmitirle para su buen funcionamiento. El trabajo que desarrolla esta Tesis Doctoral proporciona una herramienta eficaz y económica, por lo reducido de su extensión y medios, que permite allanar el camino que acomete la construcción de una estructura de tal envergadura. Mediante el análisis de la problemática del terreno y de las distintas soluciones de cimentación empleadas en la actualidad, se conduce al lector hacia una técnica de cimentación innovadora que combina la técnica del micropilotaje, para la canalización de las cargas estructurales, junto a la técnica de la inyección de fracturación hidráulica, que mejorará el terreno de implantación de los micropilotes, conformando así un medio capaz de recibir y transmitir grandes cargas en cualquier tipo de terreno. La técnica ya empleada del micropilotaje, por su trabajo esencialmente axil, requiere, aunque sin problema, la constitución de sistemas de fuerzas que equilibren el sistema de cargas provenientes del viaducto. Pero su capacidad resistente viene condicionada por el terreno circundante. Cuando la roca rodea el micropilote, su empleo se realiza sin problema y sin necesidad de mejorar el terreno. Pero sin terreno consistente, el empleo de inyecciones de fracturación hidráulica a través de los propios micropilotes, no sólo mejorará la capacidad resistente de los micropilotes, aumentando la inercia necesaria cuando las cargas son de origen sísmico o estructural ferroviario, sino que resolverá y eliminará los problemas de estabilidad que presentan las laderas que frecuentemente deben recibir las cargas de la obra de paso. Tras recoger el análisis ya realizado en el Trabajo de Investigación, donde se justificaba la alta capacidad resistente de un micropilote con terreno circundante mejorado por la inyección, en la actual Tesis se emplean modelos matemáticos sobre un caso real de viaducto sometido a un gran sismo e implantado en una enorme quebrada (500 m) de Colombia, sujeta a lluvias torrenciales y en la zona de mayor sismicidad del país. Con ello se comprueba la estabilización que se alcanza en el terreno de cimentación con el empleo de esta técnica de transmisión de carga y mejora del terreno. De esta forma se completa un ciclo que justifica las bondades de esta combinación de técnicas de cimentación, pero se abren las puertas a nuevos entornos de aplicación, como edificios antiguos de cualquier tipo que requieran recalces, y no sólo en la implantación de grandes obras de paso. ABSTRACT The establishment of a large bridge represents, in many cases, a better life for those who can take profit of the advantages provided by that structure. Nevertheless, the process of building this structure has to overcome important and difficult circumstances whenever the geotechnical conditions of the bridge site are not adequate to carry the large loads transmitted by the bridge structure. This study develops a method both effective and economical, due to the extension and means necessary for its application, which allows to solve properly the foundation of a structure of that importance. Considering the geotechnical problems inherent to the bridge site, along with the different foundation solutions that are presently used and their limitations, the study leads the reader to an innovative technique which combines the micropile system, for transmission of the structural loads of the bridge, with the technique of hydraulic fracture grouting for improvement of the ground around the micropiles, allowing to both stabilizing and transmitting large loads in any kind of ground. It is well known that the micropiles work axially, and this condition requires an adequate distribution of those units, in order to properly absorb the load system introduced by the viaduct. The resistance of the bridge foundation is, in any case, provided by the ground. When rock is encountered, the micropiles have been successfully used without improving the ground. However, as it is shown in this study, by using the micropiles as sleeve-pipes for hydraulic fracture grouting, not only the micropile resistance can be improved in any ground, but it is possible to develop grouted “solids” in the ground, whose inertia allows to absorb actions of structural and seismic origin. Additionally, as it is shown and analyzed in the Thesis, the ground improvement can give an adequate safety factor to the slopes frequently encountered in bridge sites. In order to properly justify those advantages of combining micropiles with ground improvement through fracture grouting around the micropiles, mathematical models have been developed and applied to a real case of a cable-stayed bridge installed on a very large ravine (500 m) in Colombia, located in the highest seismic zone of the country, and subject to torrential rains. The results of this numerical analysis show the high safety condition provided by the ground improvement to the viaduct site. In conclusion, the Thesis shows the important improvement that can be provided by the combination of micropiles and soil improvement, through fracture grouting, to the problem of founding bridges. However, it can be understood that this technique could be applied successfully to underpinning buildings, specially old buildings of any type, apart from its use in bridge foundations.

Passarela estaiada com tabuleiro de madeira laminada protendida em módulos curvos

É inegável a importância do desenvolvimento de tecnologias de uso racional da madeira e de solução de problemas de transportes em nossas cidades, principalmente por causa do processo crescente de urbanização do mundo. Existe também, a necessidade estética de se unir à alta tecnologia, o belo. As passarelas estaiadas com tabuleiro de madeira laminada protendida, em módulos curvos, atendem a todas estas exigências. A construção de um protótipo permitiu que a realização de ensaios estáticos e dinâmicos, cujos resultados evidenciaram a viabilidade técnica e econômica de passarelas estaiadas usando madeira de reflorestamento, de tabuleiros compostos apenas por placas de madeira laminada protendida e da construção de placas curvas de madeira laminada protendida. Também foi possível comprovar que as vibrações induzidas por pedestres são a condição mais crítica de projeto. A investigação da perda de curvatura do tabuleiro demonstrou o sucesso do projeto, embora mais estudos ao longo do tempo sejam necessários. Baseando-se nos resultados experimentais, realizou-se a calibração do modelo numérico, que permitiu realizar simulações para determinar quais variáveis definem a resposta da passarela construída. Sugestões de procedimentos de elaboração e construção de passarelas, assim como de criação de norma brasileira específica para pontes e passarelas de madeira, são apresentadas.

Pandeo simultáneo de pilas de puente: aplicación a un cálculo sísmico tipo push-over de las pilas del puente atirantado de Bucaramanga en Colombia

Se presenta el algoritmo implementado para probar la estabilidad de pilas de puente de forma global, es decir, integradas en la estructura más general del puente. El método planteado constituye una alternativa más general al método habitual de leyes momento-curvatura. Se describe su aplicación al puente atirantado de Bucaramanga de 292 m de luz y pilas de 50 y 70 m de altura (altura total de la torre mayor de 133 m). Su aplicación, considerando confinamiento en determinadas secciones de pilas permite tener en cuenta la generación de rótulas plásticas y demostrar el grado de ductilidad alcanzado en la estructura, constituyendo una aplicación practica del método de calculo sísmico por capacidad o push-over a pilas de puente.The relevance of this article is threefold: 1st It presents in detail the algorithm used to test the stability of bridge piers in a global model, i.e., integrated in the most general structure of the bridge. 2nd The method put forward represents a more general alternative to the commonly used moment-curvature method of sectional analysis for biaxial bending under constant axial force. 3rd It describes the algorithm’s application to a 292 m span cable-stayed bridge with piers of 50 and 70 m in height (total height of the biggest tower 133 m). Its application, considering confinement in some particular cross-sections of piers permits the taking into account of “plastic hinges” phenomena due to earthquakes and demonstrates the degree of ductility achieved in the structure. This constitutes a practical application of the push-over method to bridge piers.

Model updating using genetic algorithms with sequential niche technique

The authors would like to express their gratitude to organizations and people that supported this research. Piotr Omenzetter’s work within the Lloyd’s Register Foundation Centre for Safety and Reliability Engineering at the University of Aberdeen is supported by Lloyd’s Register Foundation. The Foundation helps to protect life and property by supporting engineering-related education, public engagement and the application of research. Ben Ryder of Aurecon and Graeme Cummings of HEB Construction assisted in obtaining access to the bridge and information for modelling. Luke Williams and Graham Bougen, undergraduate research students, assisted with testing.

Rescuing a telecom giant from the jaws of bankruptcy: a case study and an interview with Sir Richard Lapthorne, chairman of Cable & Wireless

Purpose – The purpose of this paper is to demonstrate key strategic decisions involved in turning around a large multinational operating in a dynamic market. Design/methodology/approach – The paper is based on analysis of archival documents and a semi-structured interview with the chairman of the company credited with its rescue. Findings – Turnaround is complex and involves both planned and emergent strategies. The progress is non-linear requiring adjustment and change in direction of travel. Top management credibility and vision is critical to success. Rescue is only possible if the company has a strong cash generative business among its businesses. The speed of decision making, decisiveness and the ability to implement strategy are among the key ingredients of success. Originality/value – Turnaround is an under-researched area in strategy. This paper contributes to a better understanding in this important area and bridges the gap between theory and practice. It provides a practical view and demonstrates how a leading executive with significant expertise and successful turnaround track record deals with inherent dilemmas of turnaround

Paul Bunyan Bridge Builders spinning cable wires across the Straits of Mackinac

verso: #1342 10/10/56 Adjusting cable wires, top of south tower, after passing of spinning wheel

Use of Fiber Reinforced Polymer Composite Cable for Post-tensioning Application

Corrosion of steel tendons is a major problem for post-tensioned concrete, especially because corrosion of the steel strands is often hard to detect inside grouted ducts. Non-metallic tendons can serve as an alternative material to steel for post-tensioning applications. Carbon fiber reinforced polymer (CFRP), given its higher strength and elastic modulus, as well as excellent durability and fatigue strength, is the most practical option for post-tensioning applications. The primary objective of this research project was to assess the feasibility of the use of innovative carbon fiber reinforced polymer (CFRP) tendons and to develop guidelines for CFRP in post-tensioned bridge applications, including segmental bridges and pier caps. An experimental investigation and a numerical simulation were conducted to compare the performance of a scaled segmental bridge model, post-tensioned with two types of carbon fiber strands and steel strands. The model was tested at different prestress levels and at different loading configurations. While the study confirms feasibility of both types of carbon fiber strands for segmental bridge applications, and their similar serviceability behavior, strands with higher elastic modulus could improve structural performance and minimize displacements beyond service loads. As the second component of the project, a side-by-side comparison of two types of carbon fiber strands against steel strands was conducted in a scaled pier cap model. Two different strand arrangements were used for post-tensioning, with eight and six strands, respectively representing an over-design and a slight under-design relative to the factored demand. The model was tested under service and factored loads. The investigation confirmed the feasibility of using carbon fiber strands in unbonded post-tensioning of pier caps. Considering both serviceability and overload conditions, the general performance of the pier cap model was deemed acceptable using either type of carbon fiber strands and quite comparable to that of steel strands. In another component of this research, creep stress tests were conducted with carbon fiber composite cable (CFCC). The anchorages for all the specimens were prepared using a commercially available expansive grout. Specimens withstood 95% of the guaranteed capacity provided by the manufacturer for a period of five months, without any sign of rupture.

ASSOCIATION OF A MYOSIN MOTOR WITH MEMBRANE-BOUNDED PIGMENT GRANULES IN FRESHWATER SHRIMP CHROMATOPHORES: EVIDENCE FROM THE NITELLA ACTIN-CABLE ASSAY

We have adapted an actin-mosin motility assay to examine the interactions in vitro between actin cables isolated from the giant internodal cells of the freshwater alga, Nitella, and pigment granules extracted from red ovarian chromatophores of the freshwater palaemonid shrimp, Macrobrachium olfersi. The chromatophore pigment mass consists of large (0.5-1.0-mu m diameter) membrane-bounded granules, and small (140-nm diameter), a membranous granules, both structurally continuous with the abundant smooth endoplasmic reticulum. Our previous immunocytochemical studies show a myosin motor to be stably associated with the pigment mass; however, to which granule type or membrane the myosin motor is attached is unclear. Here, we show that sodium vanadate, a myosin ATPase inhibitor, markedly increases the affinity of isolated, large, membrane-bounded granules for Nitella actin cables to which they become permanently attached. This interaction does not occur in granule preparations containing ATP with uninhibited, active myosin without vanadate. We propose that a stable state of elevated affinity is established between the granule-located myosin motor and the Nitella actin cables, resulting from a vanadate-inhibited acto-myosin-ADP complex. This finding provides further evidence for a myosin motor positioned on the surface of the membrane-bounded pigment granules in shrimp ovarian chromatophores.

The role of disulfide bridges in the 3-D structures of the antimicrobial peptides gomesin and protegrin-1: a molecular dynamics study

Some antimicrobial peptides have a broad spectrum of action against many different kinds of microorganisms. Gomesin and protegrin-1 are examples of such antimicrobial peptides, and they were studied by molecular dynamics in this research. Both have a beta-hairpin conformation stabilized by two disulfide bridges and are active against Gram-positive and Gram-negative bacteria, as well as fungi. In this study, the role of the disulfide bridge in the maintenance of the tertiary peptide structure of protegrin-1 and gomesin is analyzed by the structural characteristics of these peptides and two of their respective variants, gomy4 and proty4, in which the four cysteines are replaced by four tyrosine residues. The absence of disulfide bridges in gomy4 and proty4 is compensated by overall reinforcement of the original hydrogen bonds and extra attractive interactions between the aromatic rings of the tyrosine residues. The net effects on the variants with respect to the corresponding natural peptides are: i) maintenance of the original beta-hairpin conformation, with great structural similarities between the mutant and the corresponding natural peptide; ii) combination of positive F and. Ramachandran angles within the hairpin head region with a qualitative change to a combination of positive (F) and negative (.) angles, and iii) significant increase in structural flexibility. Experimental facts about the antimicrobial activity of the gomesin and protegrin-1 variants have also been established here, in the hope that the detailed data provided in the present study may be useful for understanding the mechanism of action of these peptides.

Fretting fatigue in overhead conductors: Rig design and failure analysis of a Grosbeak aluminium cable steel reinforced conductor

The performance optimisation of overhead conductors depends on the systematic investigation of the fretting fatigue mechanisms in the conductor/clamping system. As a consequence, a fretting fatigue rig was designed and a limited range of fatigue tests was carried out at the middle high cycle fatigue regime in order to access an exploratory S-N curve for a Grosbeak conductor, which was mounted on a mono-articulated aluminium clamping system. Subsequent to these preliminary fatigue tests, the components of the conductor/clamping system, such as ACSR conductor, upper and lower clamps, bolt and nuts, were subjected to a failure analysis procedure in order to investigate the metallurgical free variables interfering on the fatigue test results, aiming at the optimisation of the testing reproducibility. The results indicated that the rupture of the planar fracture surfaces observed in the external At strands of the conductor tested under lower bending amplitude (0.9 mm) occurred by fatigue cracking (I mm deep), followed by shear overload. The V-type fracture surfaces observed in some At strands of the conductor tested under higher bending amplitude (1.3 mm) were also produced by fatigue cracking (approximately 400 mu m deep), followed by shear overload. Shear overload fracture (45 degrees fracture surface) was also observed on the remaining At wires of the conductor tested under higher bending amplitude (1.3 mm). Additionally, the upper and lower Al-cast clamps presented microstructure-sensitive cracking, which was folowed by particle detachment and formation of abrasive debris on the clamp/conductor tribo-interface, promoting even further the fretting mechanism. The detrimental formation of abrasive debris might be inhibited by the selection of a more suitable class of as-cast At alloy for the production of clamps. Finally, the bolt/nut system showed intense degradation of the carbon steel nut (fabricated in ferritic-pearlitic carbon steel, featuring machined threads with 190 HV), with intense plastic deformation and loss of material. Proper selection of both the bolt and nut materials and the finishing processing might prevent the loss in the clamping pressure during the fretting testing. It is important to control the specification of these components (clamps, bolt and nuts) prior to the start of large scale fretting fatigue testing of the overhead conductors in order to increase the reproducibility of this assessment. (c) 2008 Elsevier Ltd. All rights reserved.

Modeling technique for honeycomb FRP deck bridges via finite elements

Honeycomb structures have been used in different engineering fields. In civil engineering, honeycomb fiber-reinforced polymer (FRP) structures have been used as bridge decks to rehabilitate highway bridges in the United States. In this work, a simplified finite-element modeling technique for honeycomb FRP bridge decks is presented. The motivation is the combination of the complex geometry of honeycomb FRP decks and computational limits, which may prevent modeling of these decks in detail. The results from static and modal analyses indicate that the proposed modeling technique provides a viable tool for modeling the complex geometry of honeycomb FRP bridge decks. The modeling of other bridge components (e.g., steel girders, steel guardrails, deck-to-girder connections, and pier supports) is also presented in this work.