Análise experimental de lajes lisas nervuradas de concreto armado com armadura de cisalhamento

Lajes lisas nervuradas bidirecionais são elementos estruturais de concreto armado apoiados diretamente sobre pilares, sujeitas a solicitações importantes nas duas direções, possibilitam maior velocidade na execução da obra e economia considerável de formas e concreto e, conseqüentemente, mão-de-obra. Este trabalho visa contribuir para o estudo do comportamento deste tipo de laje, quanto a resistência ao cisalhamento nas nervuras e à punção na região maciça das lajes, através de ensaios de 8 lajes lisas nervuradas bidirecionais de concreto armado. Foram realizadas análises comparativas entre os resultados obtidos experimentalmente e os fornecidos por normas técnicas nacionais e internacionais. As lajes eram quadradas de lado igual a 1.800 mm de comprimento e altura total de 140 mm. A seção transversal das lajes foi formada por nervuras de 50 mm de largura na base menor e 100 mm na base maior e os vazios entre as nervuras foram preenchidos com blocos de EPS (poliestireno expandido). As principais variáveis consideradas foram o tipo de armadura de cisalhamento nas nervuras (treliça, estribo vertical fechado e estribo aberto inclinado a 45) e a utilização de estribo aberto inclinado a 45 como armadura de punção na região maciça. Foram apresentados e analisados os resultados observados para os deslocamentos verticais, deformação nas armaduras de cisalhamento e de flexão, e a propagação das fissuras. Os valores observados para cargas últimas foram comparados com os resultados estimados. Observou-se que as armaduras de cisalhamento nas nervuras não ocasionaram ganhos significativos na resistência última e que a armadura de punção elevou significativamente a resistência das lajes.

Dimensionamento de armaduras longitudinais sujeitas à fadiga em vigas de pontes ferroviárias de concreto armado

As pontes ferroviárias de concreto armado estão sujeitas às ações dinâmicas variáveis devido ao tráfego de veículos. Estas ações podem resultar no fenômeno de fadiga do aço e do concreto dessas estruturas. No dimensionamento de estruturas de concreto armado sujeitas à carregamento cíclico, de modo geral, a fadiga é considerada simplificadamente, por meio de um coeficiente kf, denominado coeficiente de fadiga. Esse coeficiente majora a área de aço inicialmente calculada para atender ao Estado Limite Último (ELU), com a finalidade de limitar, em serviço, as variações de tensões no aço de modo a garantir uma vida útil de no mínimo 2.000.000 de ciclos. O presente trabalho apresenta melhorias nas hipóteses utilizadas pelo coeficiente de fadiga kf, permitindo o dimensionamento de armaduras longitudinais sujeitas à fadiga, para números de ciclos superiores a 2 milhões, que é o valor proposto pelo EB-3/67, e também de forma a atender a vida útil à fadiga especificada em projeto. Neste caso, foi necessário propor um método simplificado para a estimativa do número de ciclos operacionais, apartir de um ciclo padrão obtido pela máxima variação de momentos fletores provocados pelo tremtipo carregado. O estudo foi desenvolvido tomando-se como protótipo um viaduto ferroviário isostático em concreto armado da Estrada de Ferro Carajás (EFC). Os trens-tipo utilizados foram os quais operam atualmente na EFC, que correspondem ao trem de minério Carregado e Descarregado. Para determinação dos esforços solicitantes na estrutura foi elaborado um modelo numérico no programa SAP 2000. A vida útil à fadiga das armaduras longitudinais foram determinadas apartir da regra de dano de Miner e das curvas S-N da NBR 6118. A metodologia proposta neste trabalho permitiu o dimensionamento nas armaduras longitudinais à fadiga satisfatoriamente em relação à vida útil especificada no projeto, sendo que as vidas úteis que tiveram maior divergência em relação ao valor estipulado foram as de 300 e 400 anos.

Avaliação de momentos fletores em estruturas de fundação tipo radier em concreto armado

It aims the comparison of these moments between an analytical plates theory and a computational numerical simulation. It is accented the details of studies about analytical theory as well the process, step by step, of a program that has as an influence the method of finite elements. The theory of plates has an extremely importance when it is talked about slabs and it takes as a base some fundamental hypotheses (that the middle point of the plate is considered flat and under formable) the points that are normal in relation to the middle surface is not considered because of its intensity that is irrelevant in comparison to the rest. The computational programs offer good results when they are applied in a correct way and, it resolves numerous functions in a short period of time. The objective is to highlight the importance of bending moments, its points of maximum and minimum, that has the objective of realize a good reinforcement sizing for a reinforced concrete. Furthermore, it can propitiate an economy in places that is demanded a small quantity of steel, before dimensioned for a load that is distributed in all the surface of the plate, at the same intensity

Determinação do posicionamento ótimo de apoios em pontes

This paper presents a study to determine the optimal support positions in bridges, as well as the optimal relation between the spans of beams, aiming both the reduction and the unifirmization of the efforts in these structures. The mathematical problem is formulated in order to minimize the maximum bending moments, taking the coordinate of each internal support as design variable. To take into account possible location limitations, size constraints are also considered in the formulation. The software developed based on this study determines the efforts in each support for load shifting along the structure by the usage of the Displacement Method, and the optimization is performed with a mathematical programming technique. The structures analyzed from the computational implementation of the idealized model point to the validation and efficiency of the proposed procedure.

Projeto estrutural de galpão metálico segundo recomendações da NBR8800

This work deals in a general way, the history and advantages of steel buildings, as well as its increasing usage in Brazil in the last century. This work also generally describes some types and its uses of metal frame. It also demonstrates the use of the NBR 8800: 2008 standard and its calculation methods through the scale out materials regulated in Brazil for an industrial warehouse project small and simple portico metal frame. Given that the construction requirements include a locational influence following the normative indications of the NBR 6123, for the winding scale out, since this effect combined with the permanent loads must be seriously evaluated due to the shape type effort about acting simultaneous axial force and bending moments obeying the limitations applied to the structure according to NBR 8800. As it has been explained the calculations that ensures mechanical stability and suggesting an analysis of the efficiency of the used materials

Projeto estrutural de galpão metálico segundo recomendações da NBR8800

This work deals in a general way, the history and advantages of steel buildings, as well as its increasing usage in Brazil in the last century. This work also generally describes some types and its uses of metal frame. It also demonstrates the use of the NBR 8800: 2008 standard and its calculation methods through the scale out materials regulated in Brazil for an industrial warehouse project small and simple portico metal frame. Given that the construction requirements include a locational influence following the normative indications of the NBR 6123, for the winding scale out, since this effect combined with the permanent loads must be seriously evaluated due to the shape type effort about acting simultaneous axial force and bending moments obeying the limitations applied to the structure according to NBR 8800. As it has been explained the calculations that ensures mechanical stability and suggesting an analysis of the efficiency of the used materials

Contribution to assessing the stiffness reduction of structural elements in the global stability analysis of precast concrete multi-storey buildings

This study deals with the reduction of the stiffness in precast concrete structural elements of multi-storey buildings to analyze global stability. Having reviewed the technical literature, this paper present indications of stiffness reduction in different codes, standards, and recommendations and compare these to the values found in the present study. The structural model analyzed in this study was constructed with finite elements using ANSYS® software. Physical Non-Linearity (PNL) was considered in relation to the diagrams M x N x 1/r, and Geometric Non-Linearity (GNL) was calculated following the Newton-Raphson method. Using a typical precast concrete structure with multiple floors and a semi-rigid beam-to-column connection, expressions for a stiffness reduction coefficient are presented. The main conclusions of the study are as follows: the reduction coefficients obtained from the diagram M x N x 1/r differ from standards that use a simplified consideration of PNL; the stiffness reduction coefficient for columns in the arrangements analyzed were approximately 0.5 to 0.6; and the variation of values found for stiffness reduction coefficient in concrete beams, which were subjected to the effects of creep with linear coefficients from 0 to 3, ranged from 0.45 to 0.2 for positive bending moments and 0.3 to 0.2 for negative bending moments.

Kinematic internal forces in deep foundations with inclined piles

[EN] This paper presents a parametric study that looks into the influence of pile rake angle on the kinematic internal forces of deep foundations with inclined piles. Envelopes of maximum kinematic bending moments, shear forces and axial loads are presented along single inclined piles and 2X2 symmetrial square pile groups with inclined elements subjected to an earthquake generated by vertically-incident shear waves.

Glacier Calving: A Numerical Model of Forces in the Calving-Speed/Water-Depth Relation

Empirical data suggest that the race of calving of grounded glaciers terminating in water is directly proportional to the water depth. Important controls on calving may be the extent to which a calving face tends to become oversteepened by differential flow within the ice and the extent to which bending moments promote extrusion and bottom crevassing at the base of a calving face. Numerical modelling suggests that the tendency to become oversteepened increases roughly linearly with water depth. In addition, extending longitudinal deviatoric stresses at the base of a calving face increase with water depth. These processes provide a possible physical explanation for the observed calving-rate/water-depth relation.

Beitrag zur Entwicklung der Querschnittsgestaltung im Verbundbrückenbau

Die grafische Darstellung des Verbundquerschnittes mit einer oberen Betonplatte und einem darunter liegenden Stahlträger war seit seiner Vorstellung in den 1950er Jahren ein Symbol, das weit über die Theorie hinausging und weite Verbreitung in der Praxis des Verbundbrückenbaus fand. Seit den 1970er bzw. 1980er Jahren hat dieses Bild – bedingt durch neue und freiere Formen, Beton und Stahl miteinander zu kombinieren – seine Symbolhaftigkeit verloren. In Deutschland und Spanien wurde der Doppelverbund mit unten liegenden Betonplatten in Bereichen mit negativen Momenten eingeführt, in Frankreich werden Stahlträger auch in vorgespannten Betonquerschnitten eingebettet. Beide Ansätze haben dazu beigetragen, dass in der Gegenwart die Materialien Stahl und Beton im Verbundbau frei miteinander kombiniert werden können. On the development of sections in composite bridges. A comprehensive theory of composite construction was established in Germany by Sattler in 1953. The theoretical image of the composite section with a superior concrete slab and a lower metallic structure was shaped in addition to the analytical resolution. Theory and graphical representation were going to be known together in Europe. This figure was repeated in all theoretical and academic publications, so becoming an authentic icon of the composite section. Its translation to the bridge deck in flexion was obvious: the superior slab defines the tread platform, while the metallic structure was left off-hook at the bottom. Nevertheless, in continuous decks the section is not optimal at all in zones of negative bending moments. But the overcoming of the graphical representation of the theory did not happen immediately. It was produced after a process in which several European countries played an active role and where different mechanisms of technological transference were developed. One approach to this overcoming is the “double composite action”, with a lower concrete slab in areas of a negative bending moment. The first accomplishments, a bridge in Orasje built in 1968 with 134 m span, as well as the publications of the system proposed by Fabrizio de Miranda in 1971 did not extend nor had continuity. Spanish bridges by Fernández Ordoñez and Martínez Calzón used double composite action for the first time in 1979. The German team of Leonhard, Andrä und partners, has used it since the end of the 1980's to solve bridges of great span. Once the technology has been well known thanks to the ASCE International Congress and the Spanish International Meetings organised by the “Colegio de Ingenieros de Caminos”, double composite action has been integrated well into the structural vocabulary everywhere. In France the approach was different. What Michel Virlogeux calls “double floor composite section” was reached as an evolution of prestressed concrete bridges. In an experimental process widely known, the external prestressing allows weight reduction by diminishing the thickness of the concrete webs. The following step, in the 1980's, was the substitution of the webs by metallic elements: stiffened plates, trusses or folded plates. A direct result of this development is the Brass de la Plaine Bridge in the Reunion Island in 2001 with 280 m span. Both approaches have contributed to a freedom of design in composite construction in steel and concrete today.

Influence of the Second Flexural Mode on the Response of High-Speed Bridges

This paper deals with the assessment of the contribution of the second flexural mode to the dynamic behaviour of simply supported railway bridges. Alluding to the works of other authors, it is suggested in some references that the dynamic behaviour of simply supported bridges could be adequately represented taking into account only the contribution of the fundamental flexural mode. On the other hand, the European Rail Research Institute (ERRI) proposes that the second mode should also be included whenever the associated natural frequency is lower than 30 Hz]. This investigation endeavours to clarify the question as much as possible by establishing whether the maximum response of the bridge, in terms of displacements, accelerations and bending moments, can be computed accurately not taking account of the contribution of the second mode. To this end, a dimensionless formulation of the equations of motion of a simply supported beam traversed by a series of equally spaced moving loads is presented. This formulation brings to light the fundamental parameters governing the behaviour of the beam: damping ratio, dimensionless speed $ \alpha$=VT/L, and L/d ratio (L stands for the span of the beam, V for the speed of the train, T represents the fundamental period of the bridge and d symbolises the distance between consecutive loads). Assuming a damping ratio equal to 1%, which is a usual value for prestressed high-speed bridges, a parametric analysis is conducted over realistic ranges of values of $ \alpha$ and L/d. The results can be extended to any simply supported bridge subjected to a train of equally spaced loads in virtue of the so-called Similarity Formulae. The validity of these formulae can be derived from the dimensionless formulation mentioned above. In the parametric analysis the maximum response of the bridge is obtained for one thousand values of speed that cover the range from the fourth resonance of the first mode to the first resonance of the second mode. The response at twenty-one different locations along the span of the beam is compared in order to decide if the maximum can be accurately computed with the sole contribution of the fundamental mode.

Simplified longitudinal seismic analysis of buried tunnels

In this paper an analytical static approach to analyse buried tunnels under seismic surface waves (Rayleigh and Love waves), propagating parallel to the tunnels axis, is provided. In the proposed method, the tunnel is considered as a beam on elastic foundation by using a Winkler model to represent the subgrade reaction and the soil-structure interaction. The seismic load is imposed by giving at the base of the soil springs a determined configuration corresponding to the free-field motion. From the solution of the differential governing equations of the problem, results are obtained in form of relative displacements between points of tunnel, and therefore the seismic bending moments and shearing forces, acting on the tunnel cross section, can be computed.

A nonlinear analysis of laying a floating pipeline on the seabed

In this article, a model for the determination of displacements, strains, and stresses of a submarine pipeline during its construction is presented. Typically, polyethylene outfall pipelines are the ones treated by this model. The process is carried out from an initial floating situation to the final laying position on the seabed. The following control variables are considered in the laying process: the axial load in the pipe, the flooded inner length, and the distance of the control barge from the coast. External loads such as self-weight, dead loads, and forces due to currents and small waves are also taken into account.This paper describes both the conceptual framework for the proposed model and its practical application in a real engineering situation. The authors also consider how the model might be used as a tool to study how sensitive the behavior of the pipeline is to small changes in the values of the control variables. A detailed description of the actions is considered, especially the ones related to the marine environment such as buoyancy, current, and sea waves. The structural behavior of the pipeline is simulated in the framework of a geometrically nonlinear dynamic analysis. The pipeline is assumed to be a two-dimensional Navier_Bernoulli beam. In the nonlinear analysis an updated Lagrangian formulation is used, and special care is taken regarding the numerical aspects of sea bed contact, follower forces due to external water pressures, and dynamic actions. The paper concludes by describing the implementation of the proposed techniques, using the ANSYS computer program with a number of subroutines developed by the authors. This implementation permits simulation of the two-dimensional structural pipe behavior of the whole construction process. A sensitivity analysis of the bending moments, axial forces, and stresses for different values of the control variables is carried out. Using the techniques described, the engineer may optimize the construction steps in the pipe laying process

Refuerzo de vigas de hormigón armado mediante la aplicación de fuerzas exteriores introducidas por predeformación de perfiles metálicos

Una técnica de refuerzo de elementos flectados en general y, en particular, de vigas y forjados de hormigón armado, consiste en la disposición de perfiles metálicos por debajo de los elementos a reforzar y retacados a ellos. En muchos casos este refuerzo se diseña con un planteamiento pasivo, es decir, los perfiles no entran en carga hasta que no se incrementan las acciones sobre el elemento reforzado, o lo hacen sólo ligeramente y de forma cuantitativamente no controlada efectuando el retacado mediante cuñas metálicas. En el presente trabajo se estudia la alternativa del refuerzo de vigas de hormigón armado frente a momentos flectores con un planteamiento activo, introduciendo unas fuerzas (por ejemplo, mediante gatos o barras roscadas) entre el perfil y el elemento a reforzar, y retacando posteriormente el perfil a la viga en los puntos de introducción de las fuerzas, mediante cuñas metálicas, mortero, etc. La propuesta que formulamos en el presente trabajo de investigación para el control de las fuerzas introducidas consiste en la medida de las flechas que se producen en el perfil metálico al hacerlo reaccionar contra la viga. Esto permite el empleo de procedimientos sencillos para la predeformación del perfil que no dispongan de dispositivos de medida de la carga introducida, o bien controlar la veracidad de las medidas de las fuerzas que dan tales dispositivos. La gran fiabilidad que tiene el cálculo de flechas en jácenas metálicas hace que con este procedimiento se puedan conocer con gran precisión las fuerzas introducidas. Las medidas de las flechas se pueden llevar a cabo mediante los procedimientos de instrumentación habituales en pruebas de carga, con una precisión más que suficiente para conocer y controlar con fiabilidad el valor de las fuerzas que el perfil ejerce sobre la viga. Los perfiles necesarios para el refuerzo con esta técnica son netamente inferiores a los que se precisarían con el planteamiento pasivo antes indicado. En el trabajo de investigación se recoge un estudio sobre el número, posición y valor de las fuerzas de refuerzo a introducir, en función de la carga para la que se diseña el refuerzo y la capacidad resistente del elemento a reforzar, y se analizan los valores máximos que pueden tener dichas fuerzas, en función de la capacidad de la pieza frente a momentos de signo contrario a los debidos a las cargas gravitatorias. A continuación se analiza la interacción viga-perfil al incrementarse las cargas sobre la viga desde el instante de la ejecución del refuerzo, interacción que hace variar el valor de las fuerzas que el perfil ejerce sobre la viga. Esta variación permite contar con un incremento en las fuerzas de refuerzo si, con las cargas permanentes presentes al reforzar, no podemos introducirlas inicialmente con el valor necesario, o si se producen pérdidas en las propias fuerzas. Este es uno de los criterios a la hora de seleccionar las características del perfil. Por el contrario, dicha variación puede suponer que en algunos puntos a lo largo del vano se supere la capacidad a flexión frente a momentos de signo contrario a los debidos a las cargas gravitatorias, lo que también debe ser tenido en cuenta. Seguidamente se analizan diferentes aspectos que producen una variación en el valor de las fuerzas de refuerzo, como son las deformaciones diferidas del hormigón (fluencia y retracción), los gradientes de temperatura en la pieza, o la actuación de sobrecargas en los vanos adyacentes. Se concluye los efectos de estos fenómenos, que en ocasiones tienen gran influencia, pueden ser cuantificados por el proyectista, recogiéndose propuestas sencillas para su consideración en casos habituales. Posteriormente recogemos una propuesta de metodología de comprobación del refuerzo, en cuanto a cómo considerar la fisuración y evolución del módulo de deformación de la viga, la introducción de la seguridad, la influencia de las tolerancias de laminación en el perfil sobre el valor calculado de las flechas necesarias en el perfil para introducir las fuerzas iniciales proyectadas, o la situación accidental de fuego, entre otros aspectos. Por último, se exponen las conclusiones más relevantes de la investigación realizada, y se proponen futuras líneas de investigación. One technique for strengthening flexural members in general, and reinforced concrete beams and slabs in particular, entails caulking the underside of these members with steel shapes. This sort of strengthening is often designed from a passive approach; i.e., until the load is increased, the shapes are either not loaded or are only slightly loaded to some unquantified extent by caulking with steel shims. The present study explored the possibility of actively strengthening the capacity of reinforced concrete beams to resist bending moments by applying forces (with jacks or threaded bars, for instance) between the shape and the member to be strengthened. The shape is subsequently caulked under the beam at the points where the forces are applied with steel shims, mortar or similar. The proposal put forward in the present study to monitor the forces applied consists in measuring the deflection on the steel shape as it reacts against the beam. With this technique, the shape can be pre-strained using simple procedures that do not call for devices to measure the force applied, or the accurancy of the respective measurements can be verified. As deflection calculations in steel girders are extremely reliable, the forces applied with this procedure can be very precisely determined. Standard instrumental procedures for load testing can be used to measure deflection with more than sufficient precision to reliably determine and monitor the value of the forces exerted on the beam by the shape. Moreover, the shapes required to strengthen members with this technique are substantially smaller than the ones needed in the aforementioned passive approach. This study addressed the number, position and value of the strengthening forces to be applied in terms of the load for which strengthening was designed and the bearing capacity of the member to be strengthened. The maximum value of such forces was also analysed as a function of the capacity of the member to resist counter-gravity moments. An analysis was then conducted of beam-shape interaction when the load on the beam raises since the instant that strengthening is applied, interaction that alters the forces applied to the beam by the shape. This variation can provide an increment in the forces if we cannot introduce them initially with the value calculated as necessary because they were limited by the permanent loads existing when strengthening, or if losses occur in the forces themselves. This is one of the criteria for defining shape specifications. Conversely, such variation may cause the forces to exceed beam counter-gravity bending strength at some points in the span, a development that must also be taken into consideration. Other factors inducing variations in the strengthening force values were then analysed, including deferred concrete strain (creep and shrinkage), temperature gradients in the member and the live loads acting on adjacent spans. The inference drawn was that these developments, which may on occasion have a heavy impact, can be quantified by the design engineer, particularly in ordinary situations, for which simple procedures are proposed. Methodology is likewise proposed for verifying strength in terms of how to appraise beam's cracking and variations in modulus of deformation; safety concerns; the effect of shape lamination tolerance on the calculated deflection necessary for the shape to apply the design forces; and fire-induced situations, among others. Lastly, the most prominent conclusions are discussed and future lines of research are suggested.

Análisis del comportamiento de uniones metálicas viga-soporte mediante modelo de elementos finitos y comparación de resultados con el modelo de nudos y barras

Para el proyecto y cálculo de estructuras metálicas, fundamentalmente pórticos y celosías de cubierta, la herramienta más comúnmente utilizada son los programas informáticos de nudos y barras. En estos programas se define la geometría y sección de las barras, cuyas características mecánicas son perfectamente conocidas, y sobre las cuales obtenemos unos resultados de cálculo concretos en cuanto a estados tensionales y de deformación. Sin embargo el otro componente del modelo, los nudos, presenta mucha mayor complejidad a la hora de establecer sus propiedades mecánicas, fundamentalmente su rigidez al giro, así como de obtener unos resultados de estados tensionales y de deformación en los mismos. Esta “ignorancia” sobre el comportamiento real de los nudos, se salva generalmente asimilando a los nudos del modelo la condición de rígidos o articulados. Si bien los programas de cálculo ofrecen la posibilidad de introducir nudos con una rigidez intermedia (nudos semirrígidos), la rigidez de cada nudo dependerá de la geometría real de la unión, lo cual, dada la gran variedad de geometrías de uniones que en cualquier proyecto se nos presentan, hace prácticamente inviable introducir los coeficientes correspondientes a cada nudo en los modelos de nudos y barras. Tanto el Eurocódigo como el CTE, establecen que cada unión tendrá asociada una curva momento-rotación característica, que deberá ser determinada por los proyectistas mediante herramientas de cálculo o procedimientos experimentales. No obstante, este es un planteamiento difícil de llevar a cabo para cada proyecto. La consecuencia de esto es, que en la práctica, se realizan extensas comprobaciones y justificaciones de cálculo para las barras de las estructuras, dejando en manos de la práctica común la solución y puesta en obra de las uniones, quedando sin justificar ni comprobar la seguridad y el comportamiento real de estas. Otro aspecto que conlleva la falta de caracterización de las uniones, es que desconocemos como afecta el comportamiento real de éstas en los estados tensionales y de deformación de las barras que acometen a ellas, dudas que con frecuencia nos asaltan, no sólo en la fase de proyecto, sino también a la hora de resolver los problemas de ejecución que inevitablemente se nos presentan en el desarrollo de las obras. El cálculo mediante el método de los elementos finitos, es una herramienta que nos permite introducir la geometría real de perfiles y uniones, y nos permite por tanto abordar el comportamiento real de las uniones, y que está condicionado por su geometría. Por ejemplo, un caso típico es el de la unión de una viga a una placa o a un soporte soldando sólo el alma. Es habitual asimilar esta unión a una articulación. Sin embargo, el modelo por elementos finitos nos ofrece su comportamiento real, que es intermedio entre articulado y empotrado, ya que se transmite un momento y el giro es menor que el del apoyo simple. No obstante, la aplicación del modelo de elementos finitos, introduciendo la geometría de todos los elementos estructurales de un entramado metálico, tampoco resulta en general viable desde un punto de vista práctico, dado que requiere invertir mucho tiempo en comparación con el aumento de precisión que obtenemos respecto a los programas de nudos y barras, mucho más rápidos en la fase de modelización de la estructura. En esta tesis se ha abordado, mediante la modelización por elementos finitos, la resolución de una serie de casos tipo representativos de las uniones más comúnmente ejecutadas en obras de edificación, como son las uniones viga-pilar, estableciendo el comportamiento de estas uniones en función de las variables que comúnmente se presentan, y que son: •Ejecución de uniones viga-pilar soldando solo por el alma (unión por el alma), o bien soldando la viga al pilar por todo su perímetro (unión total). •Disposición o no de rigidizadores en los pilares •Uso de pilares de sección 2UPN en cajón o de tipo HEB, que son los tipos de soporte utilizados en casi el 100% de los casos en edificación. Para establecer la influencia de estas variables en el comportamiento de las uniones, y su repercusión en las vigas, se ha realizado un análisis comparativo entre las variables de resultado de los casos estudiados:•Estados tensionales en vigas y uniones. •Momentos en extremo de vigas •Giros totales y relativos en nudos. •Flechas. Otro de los aspectos que nos permite analizar la casuística planteada, es la valoración, desde un punto de vista de costos de ejecución, de la realización de uniones por todo el perímetro frente a las uniones por el alma, o de la disposición o no de rigidizadores en las uniones por todo el perímetro. Los resultados a este respecto, son estrictamente desde un punto de vista económico, sin perjuicio de que la seguridad o las preferencias de los proyectistas aconsejen una solución determinada. Finalmente, un tercer aspecto que nos ha permitido abordar el estudio planteado, es la comparación de resultados que se obtienen por el método de los elementos finitos, más próximos a la realidad, ya que se tiene en cuenta los giros relativos en las uniones, frente a los resultados obtenidos con programas de nudos y barras. De esta forma, podemos seguir usando el modelo de nudos y barras, más versátil y rápido, pero conociendo cuáles son sus limitaciones, y en qué aspectos y en qué medida, debemos ponderar sus resultados. En el último apartado de la tesis se apuntan una serie de temas sobre los que sería interesante profundizar en posteriores estudios, mediante modelos de elementos finitos, con el objeto de conocer mejor el comportamiento de las uniones estructurales metálicas, en aspectos que no se pueden abordar con los programas de nudos y barras. For the project and calculation of steel structures, mainly building frames and cover lattices, the tool more commonly used are the node and bars model computer programs. In these programs we define the geometry and section of the bars, whose mechanical characteristics are perfectly known, and from which we obtain the all calculation results of stresses and displacements. Nevertheless, the other component of the model, the nodes, are much more difficulty for establishing their mechanical properties, mainly the rotation fixity coefficients, as well as the stresses and displacements. This "ignorance" about the real performance of the nodes, is commonly saved by assimilating to them the condition of fixed or articulated. Though the calculation programs offer the possibility to introducing nodes with an intermediate fixity (half-fixed nodes), the fixity of every node will depend on the real connection’s geometry, which, given the great variety of connections geometries that in a project exist, makes practically unviable to introduce the coefficients corresponding to every node in the models of nodes and bars. Both Eurocode and the CTE, establish that every connection will have a typical moment-rotation associated curve, which will have to be determined for the designers by calculation tools or experimental procedures. Nevertheless, this one is an exposition difficult to carry out for each project. The consequence of this, is that in the practice, in projects are extensive checking and calculation reports about the bars of the structures, trusting in hands of the common practice the solution and execution of the connections, resulting without justification and verification their safety and their real behaviour. Another aspect that carries the lack of the connections characterization, is that we don´t know how affects the connections real behaviour in the stresses and displacements of the bars that attack them, doubts that often assault us, not only in the project phase, but also at the moment of solving the execution problems that inevitably happen in the development of the construction works. The calculation by finite element model is a tool that allows us to introduce the real profiles and connections geometry, and allows us to know about the real behaviour of the connections, which is determined by their geometry. Typical example is a beam-plate or beam-support connection welding only by the web. It is usual to assimilate this connection to an articulation or simple support. Nevertheless, the finite element model determines its real performance, which is between articulated and fixed, since a moment is transmitted and the relative rotation is less than the articulation’s rotation. Nevertheless, the application of the finite element model, introducing the geometry of all the structural elements of a metallic structure, does not also turn out to be viable from a practical point of view, provided that it needs to invest a lot of time in comparison with the precision increase that we obtain opposite the node and bars programs, which are much more faster in the structure modelling phase. In this thesis it has been approached, by finite element modelling, the resolution of a representative type cases of the connections commonly used in works of building, since are the beam-support connections, establishing the performance of these connections depending on the variables that commonly are present, which are: •Execution of beam-support connections welding only the web, or welding the beam to the support for the whole perimeter. •Disposition of stiffeners in the supports •Use 2UPN in box section or HEB section, which are the support types used in almost 100% building cases. To establish the influence of these variables in the connections performance, and the repercussion in the beams, a comparative analyse has been made with the resulting variables of the studied cases: •Stresses states in beams and connections. •Bending moments in beam ends. •Total and relative rotations in nodes. •Deflections in beams. Another aspect that the study allows us to analyze, is the valuation, from a costs point of view, of the execution of connections for the whole perimeter opposite to the web connections, or the execution of stiffeners. The results of this analyse, are strictly from an economic point of view, without prejudice that the safety or the preferences of the designers advise a certain solution. Finally, the third aspect that the study has allowed us to approach, is the comparison of the results that are obtained by the finite element model, nearer to the real behaviour, since the relative rotations in the connections are known, opposite to the results obtained with nodes and bars programs. So that, we can use the nodes and bars models, more versatile and quick, but knowing which are its limitations, and in which aspects and measures, we must weight the results. In the last part of the tesis, are relationated some of the topics on which it would be interesting to approach in later studies, with finite elements models, in order to know better the behaviour of the structural steel connections, in aspects that cannot be approached by the nodes and bars programs.