Effective-fourth-order resonator based MASH bandpass sigma-delta modulators

Two novel effective-fourth-order (eighth-order) resonator based MASH (MultistAge noise SHaping) bandpass Σ-Δ modulators are introduced at the behavioural level and subsequently examined by simulations utilising the ALTA SPW environment. The considered bandpass configurations have in their loop filter a cascade of standard second-order resonator structures in order to achieve appropriate noise shaping. The quantisation noise in each stage is suppressed by feeding the error of each section into the input of the following stage. It is demonstrated in this paper that the quadruple effective-first-order cascade configuration has significantly better performance as well as conforming more closely with theory in comparison with the effective-second-order effective-second-order cascade. The superior performance of the former can be attributed to the cumulative effect of the multi-bit outputs as well as the presence of more notch filters.

MASH structures for bandpass sigma-delta modulators

The paper presents simulation results from investigating the behaviour of multistage (MASH) oversampled bandpass sigma-delta (Σ-Δ) modulators for use in analogue to digital converters for high frequency narrowband applications such as the signals out of the intermediate frequency (IF) section of a superheterodyne radio receiver. The bandpass configurations under consideration have in their loop filter a cascade of second-order resonator structures in order to achieve acceptable noise shaping. The quantisation noise in each stage is suppressed by feeding the error of each section into the input of the following stages. It is demonstrated that the triple effective-first-order bandpass MASH structure has significantly better performance compared with the effective-second-order effective-first-order bandpass MASH structure.

Compact high linearity switchable dual-mode microstrip bandpass filters

A compact highly linear microstrip dual-mode electronically switchable filter is presented. The key characteristics of the dual-mode switchable filter are investigated and described. A second order filter design procedure is outlined to facilitate the realisation of Butterworth and Chebyshev functions. The proposed filter was built and tested with NXP pin diode model BAP65-03. The measured and simulated results are in good agreement. The measured insertion loss in the ON state was 3.0 dB the isolation in the OFF state was 45 dB at the centre frequency. An evaluation of filter distortion is presented for digitally modulated 16 QAM and QPSK signals.

Ultra compact pseudo-elliptic inline waveguide bandpass filters using bypass coupling

This paper presents an ultra compact waveguide bandpass filter that exhibits a pseudo-elliptic response. The transmission zero created in the upper stopband to form a rapid roll off is produced through a bypass coupling with higher order modes. A 3rd order filter is designed at the centre frequency of 9.4 GHz with a 5.3% fractional bandwidth. The proposed structure's size is 38% smaller than one of a 3rd order E-plane extracted pole filter with comparable response. Additionally, this configuration allows larger span of different bandwidths. The filter has been fabricated and tested using E-plane waveguide technology, which has benefits of being inexpensive and having mass producible capabilities. Measurements of such a fabricated filter validate the simulated results.

Ultra compact inline E-plane waveguide extracted pole bandpass filters

This letter presents an ultra compact extracted pole E-plane filter. The proposed structure can achieve up to 65% size reduction in comparison with a standard extracted pole filter designed at 9.5 GHz centre frequency with a 3% fractional bandwidth. The filter has been fabricated and tested using E-plane waveguide technology. Measurements on a fabricated filter confirm the accuracy of the design method.

Miniaturised sharp rejection bandpass filter with reconfigurable bandwidth for UWB applications

A novel, compact and highly selective microstrip bandpass filter with bandwidth reconfigurability for ultra-wideband (UWB) applications is presented. The proposed design uses stepped impedance resonator (SIR) for realization of bandpass filter (BPF) and employs a single varactor diode (BB135-NXP) for the purpose of reconfiguring bandwidth. Additionally, to improve the selectivity between passband edges, a cross-coupling between I/O feed lines is introduced which generated pairs of attenuation poles at each side of the passband. Measurements on a fabricated reconfigurable filter confirm the accuracy of the design procedure. Measured responses show good agreement with simulation. The proposed filter is able to achieve significant size reduction (8.5 mm × 7.1 mm excluding the feeding ports) as compared to the conventional bandpass filters with reconfigurable bandwidth.

Achieving accurate FTIR measurements on high performance bandpass filters

The sources of ordinate error in FTIR spectrometers are reviewed with reference to measuring small out-of-band features in the spectra of bandpass filters. Procedures for identifying instrumental artefacts are described. It is shown that features well below 0.01%T can be measured reliably.

High-performance infrared narrow-bandpass filters for the Indian National Satellite System meteorological instrument (INSAT-3D)

This paper describes the design and manufacture of a set of precision cooled (210K) narrow-bandpass filters for the infrared imager and sounder on the Indian Space Research Organisation (ISRO) INSAT-3D meteorological satellite. We discuss the basis for the choice of multilayer coating designs and materials for 21 differing filter channels, together with their temperature-dependence, thin film deposition technologies, substrate metrology, and environmental durability performance. (C) 2008 Optical Society of America.

Spectral design of temperature-invariant narrow bandpass filters for the mid-infrared

The ability of narrow bandpass filters to discriminate wavelengths between closely-separated gas absorption lines is crucial in many areas of infrared spectroscopy. As improvements to the sensitivity of infrared detectors enables operation in uncontrolled high-temperature environments, this imposes demands on the explicit bandpass design to provide temperature-invariant behavior. The unique negative temperature coefficient (dn/dT<0) of Lead-based (Pb) salts, in combination with dielectric materials enable bandpass filters with exclusive immunity to shifts in wavelength with temperature. This paper presents the results of an investigation into the interdependence between multilayer bandpass design and optical materials together with a review on invariance at elevated temperatures.

Improving the pass-band return loss in liquid crystal dual-mode bandpass filters by microstrip patch reshaping

In this paper, the design and experimental characterization of a tunable microstrip bandpass filter based on liquid crystal technology are presented. A reshaped microstrip dual-mode filter structure has been used in order to improve the device performance. Specifically, the aim is to increase the pass-band return loss of the filter by narrowing the filter bandwidth. Simulations confirm the improvement of using this new structure, achieving a pass-band return loss increase of 1.5 dB at least. Because of the anisotropic properties of LC molecules, a filter central frequency shift from 4.688 GHz to 5.045 GHz, which means a relative tuning range of 7.3%, is measured when an external AC voltage from 0 Vrms to 15 Vrms is applied to the device.

Molecular bandpass amplifiers. Contract AF33(616)-7252. Interim scientific report no. 1- [of the] Development Laboratory, Semiconductor Division, Hughes Aircraft Co.

Mode of access: Internet.