Determination of rare and rare earth elements in soils and sediments by ICP-MS using Ti(OH)(4)-Fe(OH)(3) co-precipitation preconcentration

A method was developed for the determination of trace and ultratrace amounts of REE. Cd. In. Tl. Th. Nb, Ta. Zr and Hf in soils and sediments. With NaOH-Na2O2 as the flux. Ti(OH)(4)-Fe(OH)(3) co-precipitation as the preconcentration technique and inductively coupled plasma mass spectrometry (ICP-MS) for measurement, the whole procedure was concise and suitable for batch analysis of multi-element solutions. An investigation was carried out of the Ti(OH)(4)-Fe(OH)(3) co-precipitation system, and the results obtained showed that the natural situation of Ti tightly coexisting with Nb. Ta, Zr and Hf in geological samples plays a very important role in the complete co-precipitation of the four elements. The accuracy of this procedure was established using six Chinese soil and sediment certified reference materials (GSS and GSD). and the relative errors between the found and certified values were mostly below 10%.

Studies on the transport of lanthanides ions through the membrane of human erythrocyte in vitro by ICP-MS

A method was developed for the determination of lanthanum in the cytoplasm of human erythrocytes after they were incubated in lanthanum nitrate or citrate solutions. The lanthanum concentration in the cytoplasm of incubated erythrocytes is much higher than that in normal erythrocytes. It is suggested lanthanum can transport through the membrane of erythrocyte in vitro. Solutions containing chelator are unsuitable to be washing buffer in the investigation.

Determination of multiple trace elements in seawater using chelation ion chromatography and ICP-MS

An off-line chelation system combined with ICP-MS technique was developed for the quantitative determination of trace elements in seawater, namely V, Co, Ni, Cu, Zn, Mo, Cd, Pb, U and rare earth elements(REEs). The system was built based on an ion chromatography equipped with MetPac((R)) CC-I chelation columns which had a strong selective chelation to these target elements within a pH range 5.2-5.6. Acidified seawater samples and NH4Ac(2 mol/L) were blended to meet suitable pH before being injected into the chelation column, thus target elements were retained while alkali and alkaline metals were excluded. Then chelated elements were eluted by HNO3 (1 mol/L) and samples were collected for ICP-MS analysis. Varying the ratio of input( gen. 200 mL) to output( gen. 5 mL), the target elements which were concentrated as 40 times as their concentrations were far beyond instrumental quantification limits. At last, a certificated seawater CASS-4 was introduced and our detected values were in good agreement with those certified values.

利用MC-ICP-MS测定硼同位素及其在西藏地热和盐湖中的初步应用

Based on previous studies, boron can be separated from aqueous samples with Amberlite IRA-743 resin. Experiments on the elute temperature, elute volume and the dynamic resin exchange capacity have been performed in this study. Results show that the dynamic exchange capacity of the resin is 4.2mg B/g and at room temperature, boron fixed on the resin within this capacity level can be extracted quantitatively by using 5ml 2%HNO3. A new procedure has been developed for the measurement of boron isotope ratios in water samples using a Neptune MC-ICP-MS, after resolving the memory effect, which is a key problem, and investigating the impacts of mass bias and Si matrix effect. Using this method, it usually takes 20 min to perform one measurement on 0.1ppm boron solution with a precision of 0.23‰ (SD). If the relative deviation between a sample and the standard is large, the washout time needs to be doubled to achieve a higher precision. δ11B values of water samples from Yangbajing geothermal field vary from -10.53 to -9.13‰. Owing to the large difference B concentration and the small B isotope difference between deep geothermal water and surface water, B isotope ratios of the shallow geothermal fluids are dominated by the deep end member rather than the shallower one in the mixing process. As a consequence, δ11B-B relation is indicative basically of a dilution process. Vapor-liquid separation and calcite scaling also greatly influence B isotope fractionation. δ11B values of water samples from Dagejia geothermal field are from -15.98‰ to -11.67‰. Boron in Changma River near the field has two sources, freshwater lakes (Dajiamang Lake and Canke Lake) and geothermal waters. Finally, a preliminary discussion is included on boron geochemical characteristics of the salt lakes in Shuanghu area and other geothermal fields, to provide information for future studies on boron isotope geochemistry of geothermal systems and salt lakes in Tibet.

Lu-Hf同位素的MC-ICP-MS实验方法及其在华北克拉通典型火山岩研究中的应用

Over past ten years, a great development has been made in the Lu-Hf isotopic system with the advent of MC-ICP-MS. Based on a comprehensive review of available references in the related field, a novel analytical protocol of three exchange chromatographies after one mixed acid attacking geological samples was developed in this work, which not only avoids common multiple sample treatments for natural inhomegeneous samples, but also is useful for Rb-Sr, Sm-Nd and Lu-Hf isotopic system simultaneously, especially for the garnet- and apatite-bearing rocks for the Sm-Nd and Lu-Hf geochronology. An analytical procedure for the Lu and Hf concentration in geological samples determined by by ID-MC-ICP-MS was detailedly investigated. The Hf yield is > 90 % and total procedural blank is less than. 50 pg for Hf and 10 pg for Lu, respectively. The developed method was successfully applied to the determination of Lu and Hf concentrations for USGS geological materials. A one-column procedure for Hf purification in geological samples using common anion exchange chromatography and its isotopic analyses by MC-ICP-MS were also established. Multiple analyses of Standard Reference Materials demonstrate that this method was simple, time-saving, cheap and efficient, especially suitable for the Hf isotopic compositions of young samples. Finally, the measurements of Sr and Nd isotopic compositions using Neptune MC-ICP-MS were described briefly, which indicates that Neptune MC-ICP-MS can precisely measure Sr and Nd isotopic compositions as the TIMS does, even more efficient and less time-consuming than the TIMS method. The Hf isotopic characteristics of typical volcanic rocks (Cenozoic Changle-Linqu basalts, Mesozoic Fangcheng basalts, Mesozoic Jianguo basalts, Mesozoic Wulahada high-Mg andesite, Cenozoic Fanshi, Zuoquan and Xiyang-Pingding basalts of the Taihang Mountains, Paleozoic diamondiferous Menyin and Fuxian Kimblites) from the North China Craton were firstly studied in this work. Coupled with Nd isotopic compositions, it shows that the Hf isotopes could be a better tracer for mantle sources than the Nd isotopes. Individual kimberlite fields from both the Mengyin and Fuxian regions have quite uniform Hf isotopic compositions, similar to the situation for the Nd isotopes.

ICP-MS测定表生水体稀土过程中pH值对酸性膦萃取稀土效率的影响

针对目前最常用的液- 液萃取、ICP- M S 测定法检测表生水体中微量稀土元素方法, 研究了不同pH值条件下, 酸性膦(65%HDEHP 和35%H2M EHP) 自表生水体中萃取稀土元素(REEs) 的回收率。结果表明, 在pH1～ 4 的范围内, 不同性质的水体(湖泊、河流、地下水) 有不同的REEs 回收率。其中湖水在pH 118～ 317 有90% 以上的回收率, 最高回收率为93164%; 河水在pH 211～ 315 范围内有90% 以上的回收率, 最高回收率为95152%; 地下水仅在pH 113～ 115 时回收率超过90% , 最高回收率为97161%。说明在萃取不同表生水体中稀土元素时, 需要调到特定的pH 值才能得到最好的萃取效果。

硒、锌同位素MC-ICP-MS分析方法研究及其在生物和环境样品中的应用

一定元素的同位素组成被认为是该元素特有的“指纹”，同位素组成测量是地球化学、生命科学、环境化学、地质科学和核科学等领域重要的研究手段。利用同位素技术开展生命过程，地球系统中的物理、化学、生物过程及其资源、环境与灾害效应，资源勘探，污染物溯源等方面的研究，既是该技术的前沿研究主题，也使相关领域的研究更加“精细量化”，从而在新的科学纵深揭示出更加清晰的规律。 1992年多接收电感耦合等离子体质谱仪(MC-ICP-MS)的问世，为同位素分析提供了一种强有力的技术手段，与传统的热电离同位素质谱相比，MC-ICP-MS具有测量速度快、操作简便、灵敏度高等优点。而且，由于等离子体源产生的高温，在理论上能测量所有的金属元素和一些非金属元素，并已很好地解决了一些高电离电位元素同位素测量的难题（如Se, Zn, Hf等），用MC-ICP-MS准确、精密测量各种元素同位素组成的方法正在逐渐得到发展和完善。目前，MC-ICP-MS比较成熟的方法主要是针对核和地质科学研究中应用较多的U, Pb, Sm, Nd, Sr, Hf, B, Li等，在硒和锌同位素测量方法学的研究还相对较少（尤其是硒），对一些测量中受各种干扰较为严重的、原子量小于80 的元素同位素的测量技术还有待进一步深入探索和研究。锌、硒元素不仅与人类健康息息相关，而且随着质谱分析技术的发展，使其在环境地球化学、生命科学等领域有着广泛的应用前景。准确测量生物、食品、环境、地质等样品中的锌、硒元素含量、各种形态及其同位素组成受到越来越多的关注。锌、硒同位素准确测量的方法学研究，不仅可以广泛应用于各相关领域，也为锌和硒同位素基、标准物质研制奠定技术基础，从而为锌、硒元素含量和同位素测量提供量值溯源保障。 本工作针对锌和硒元素同位素组成以及生物、环境等样品中成分量准确测量存在的问题，通过使用六极杆碰撞室MC-ICP-MS进行准确测量锌和硒元素同位素的技术研究，结合在化学计量研究中的长期实践及相关文献，从方法学角度和应用方面得出以下结论： 1.MC-ICP-MS仪器测量主要参数，如炬管轴向位置、载气流量、碰撞气流量、仪器稳定性等对测量结果影响很大，要获得高精度的测量结果，须优化和固定参数设置，保持仪器的稳定状态。在六极杆碰撞室MC-ICP-MS测量锌同位素时，高纯氩气碰撞气模式是较为理想的模式，64Zn/66Zn、67Zn/66Zn、68Zn/66Zn同位素丰度比测量精度达到0.002－0.008％，70Zn/66Zn 测量精度达到0.01％；在高纯氢气和氩气碰撞气按一定比例混合的模式下， 76Se/80Se、77Se/80Se、78Se/80Se、82Se/80Se同位素丰度比测量精度达到0.004－0.005%。 2.采用高纯、高浓缩64Zn和66Zn配制了8个校正样品 (64Zn/66Zn：0.6－2.2)；用高纯、高浓缩同位素76Se和82Se配制了16个校正样品（76Se/82Se： 0.05－11.8），用这些样品分别测量并计算了仪器系统误差校正系数K，这些校正样品的K64/66 和 K76/82的相对标准偏差分别为0.034％和0.03％，均在仪器的测量不确定度范围内，说明在校正样品同位素变化范围内，仪器测量同位素丰度比的校正系数没有发生明显变化。 3.在硒同位素丰度比值测量中，氢气碰撞气的使用是SeH产生的重要原因之一，Ar/H在2－7之间都可以满足硒同位素比值测量的要求，即保证较高的硒灵敏度、较小的SeH生成比例、稳定的同位素比值测量结果。本工作建立了SeH的校正计算公式，在对测量结果的质量歧视进行校正时，77Se和78Se的校正更为复杂，因为它们除自身产生的SeH外，还分别受到了来自76SeH和77SeH的影响，故校正质量偏移时应首先对SeH进行校正。对于不同的SeH生成比例，经过校正后，硒的同位素丰度比校正值是一致的，并不受SeH生成比例变化影响。 4.通过对IDMS过程中的关键技术研究，明确了如何正确使用该方法以获得准确测量结果。IDMS方法在测量步骤中引入的不确定度影响因素相对于其它化学分析方法较少，并且可以被明确地表达出来，测量结果可直接溯源到国际单位，因此，该方法对化学计量学研究具有十分重要的意义。 5.建立了适用于ICP-MS测量血清、大豆粉、金枪鱼等多种复杂基体中锌和硒元素的样品前处理方法，建立了锌和硒的ICP-IDMS测量方法。将建立的方法应用于人血清标准物质研制、国家计量院之间的国际比对和合作研究中，取得的优异成绩验证了所建方法的可靠性和可比性。IDMS方法在样品前处理上不怕样品损失和高精度同位素丰度比测量的优点，使其在复杂基体中硒、锌的准确测量方面较其它分析方法具有独特的优势，可在生物、临床、环境、食品等方面的分析研究中广泛应用。

运用MC-ICP-MS测定天然样品的锂同位素组成

自然界锂同位素分馏强烈，这使得它在很多方面都得到了应用，如地球化学、天体化学和核工业等。所有这些领域都要求精确的测定6Li/7Li的比值。但由于锂是微量元素，而且在测试过程中还存在明显的干扰，因此在进行锂同位素比值测定之前必须对样品进行分离和富集。本文以锂元素标准样品和钾、钠、钙、镁元素标准样品的混合溶液为主要研究对象，采用阳离子交换树脂AG-50W-X8来分离富集锂，探索在不同淋洗介质条件下锂分离纯化的最佳介质条件。初步得出以下结论： 1、本次研究建立了相对简单、高效的锂同位素分离方法。用单一的柱子分离、提纯样品锂；用低浓度的盐酸（0.15M HCl）直接作为淋洗介质，操作过程简单。 2、对锂同位素比值测定产生潜在影响因素，如基体效应、回收率、流程空白等进行了实验研究，证实这些影响因素对于本次研究所建立的方法来说都是可以忽略不计的。 3、用MC-ICP-MS测定样品的锂同位素组成，分析结果的准确度和精度与现阶段所报道数据相同。测定海水的锂同位素组成（+31.6±1.0‰，2σ）与Tomoscak 等（+31.8±1.9‰，2σ）的分析值相近。 4、该方法也适用于低含量的样品。我们分离并测定了不同类型样品的锂同位素组成，样品锂含量在0.064µg/g和132µg/g之间，说明该方法也同样适用于低含量地质样品的分析测定。

Investigation into mercury bound to biothiols:structural identification using ESI-ion-trap MS and introduction of a method for their HPLC separation with simultaneous detection by ICP-MS and ESI-MS

Mercury in plants or animal tissue is supposed to occur in the form of complexes formed with biologically relevant thiols (biothiols), rather than as free cation. We describe a technique for the separation and molecular identification of mercury and methylmercury complexes derived from their reactions with cysteine (Cys) and glutathione (GS): Hg(Cys)(2), Hg(GS)(2), MeHgCys, MeHgGS. Complexes were characterised by electrospray mass spectrometry (MS) equipped with an ion trap and the fragmentation pattern of MeHgCys was explained by using MP2 and B3LYP calculations, showing the importance of mercury-amine interactions in the gas phase. Chromatographic baseline separation was performed within 10 min with formic acid as the mobile phase on a reversed-phase column. Detection was done by online simultaneous coupling of ES-MS and inductively coupled plasma MS. When the mercury complexes were spiked in real samples (plant extracts), no perturbation of the separation and detection conditions was observed, suggesting that this method is capable of detecting mercury biothiol complexes in plants.

Can we trust mass spectrometry for determination of arsenic peptides in plants:comparison of LC-ICP-MS and LC-ES-MS/ICP-MS with XANES/EXAFS in analysis of Thunbergia alata

The weakest step in the analytical procedure for speciation analysis is extraction from a biological material into an aqueous solution which undergoes HPLC separation and then simultaneous online detection by elemental and molecular mass spectrometry (ICP-MS/ES-MS). This paper describes a study to determine the speciation of arsenic and, in particular, the arsenite phytochelatin complexes in the root from an ornamental garden plant Thunbergia alata exposed to 1 mg As L(-1) as arsenate. The approach of formic acid extraction followed by HPLC-ES-MS/ICP-MS identified different As(III)-PC complexes in the extract of this plant and made their quantification via sulfur (m/z 32) and arsenic (m/z 75) possible. Although sulfur sensitivity could be significantly increased when xenon was used as collision gas in ICP-qMS, or when HR-ICP-MS was used in medium resolution, the As:S ratio gave misleading results in the identification of As(III)-PC complexes due to the relatively low resolution of the chromatography system in relation to the variety of As-peptides in plants. Hence only the parallel use of ES-MS/ICP-MS was able to prove the occurrence of such arsenite phytochelatin complexes. Between 55 and 64% of the arsenic was bound to the sulfur of peptides mainly as As(III)(PC(2))(2), As(III)(PC(3)) and As(III)(PC(4)). XANES (X-ray absorption near-edge spectroscopy) measurement, using the freshly exposed plant root directly, confirmed that most of the arsenic is trivalent and binds to S of peptides (53% As-S) while 38% occurred as arsenite and only 9% unchanged as arsenate. EXAFS data confirmed that As-S and As-O bonds occur in the plants. This study confirms, for the first time, that As-peptides can be extracted by formic acid and chromatographically separated on a reversed-phase column without significant decomposition or de-novo synthesis during the extraction step.

Record of natural and anthropogenic changes in reef environments (Barbados West Indies) using laser ablation ICP-MS and sclerochronology on coral cores

Coral growth rate can be affected by environmental parameters such as seawater temperature, depth, and light intensity. The natural reef environment is also disturbed by human influences such as anthropogenic pollutants, which in Barbados are released close to the reefs. Here we describe a relatively new method of assessing the history of pollution and explain how these effects have influenced the coral communities off the west coast of Barbados. We evaluate the relative impact of both anthropogenic pollutants and natural stresses. Sclerochronology documents framework and skeletal growth rate and records pollution history (recorded as reduced growth) for a suite of sampled Montastraea annularis coral cores. X-radiography shows annual growth band patterns of the corals extending back over several decades and indicates significantly lower growth rate in polluted sites. Results using laser-ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) on the whole sample (aragonite, organic matter, trapped particulate matter, etc.), have shown contrasting concentrations of the trace elements (Cu, Sn, Zn, and Pb) between corals at different locations and within a single coral. Deepwater corals 7 km apart, record different levels of Pb and Sn, suggesting that a current transported the metal pollution in the water. In addition, the 1995 hurricanes are associated with anomalous values for Sn and Cu from most sites. These are believed to result from dispersion of nearshore polluted water. We compared the concentrations of trace elements in the coral growth of particular years to those in the relevant contemporaneous seawater. Mean values for the concentration factor in the coral, relative to the water, ranged from 10 for Cu and Ni to 2.4 and 0.7 for Cd and Zn, respectively. Although the uncertainties are large (60-80%), the coral record enabled us to demonstrate the possibility of calculating a history of seawater pollution for these elements from the 1940s to 1997. Our values were much higher than those obtained from analysis of carefully cleaned coral aragonite; they demonstrate the incorporation of more contamination including that from particulate material as well as dissolved metals.

The direct determination of rare earth elements in basaltic and related rocks using ICP-MS: Testing the efficiency of microwave oven sample decomposition procedures

Tests are described showing the results obtained for the determination of REE and the trace elements Rb, Y, Zr, Nb, Cs, Ba, Hf, Ta, Pb, Th and U with ICP-MS methodology for nine basaltic reference materials, and thirteen basalts and amphibolites from the mafic-ultramafic Niquelandia Complex, central Brazil. Sample decomposition for the reference materials was performed by microwave oven digestion (HF and HNO(3), 100 mg of sample), and that for the Niquelandia samples also by Parr bomb treatment (5 days at 200 degrees C, 40 mg of sample). Results for the reference materials were similar to published values, thus showing that the microwave technique can be used with confidence for basaltic rocks. No fluoride precipitates were observed in the microwave-digested solutions. Total recovery of elements, including Zr and Hf, was obtained for the Niquelandia samples, with the exception of an amphibolite. For this latter sample, the Parr method achieved a total digestion, but not so the microwave decomposition; losses, however, were observed only for Zr and Hf, indicating difficulty in dissolving Zr-bearing minerals by microwave acid attack.

Emprego de nebulizador pneumático de ICP-MS como câmara de diluição em sistemas de injeção em fluxo para determinações multielementares

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)