An apparatus for evaluating adhesion between soils and solid surfaces

An apparatus in the direct shear mode has been developed to conduct soil-soil and soil-solid material interface tests in the undrained condition. Evaluation of the apparatus showed that all the requirements for simulating the undrained condition of shear are satisfied. The interface test results show that the adhesion factor a increases with the surface roughness of the solid material. In the case of the normally consolidated state, alpha is practically independent of the undrained shear strength of the clay for a given surface. For the overconsolidated state, alpha depends on the undrained shear strength and the overconsolidation ratio for smooth surfaces but for rough surfaces; alpha is independent of both undrained shear strength and overconsolidation ratio.

Apparatus and method for heat-run test on high-power PWM converters with low energy expenditure

Before installation, a voltage source converter is usually subjected to heat-run test to verify its thermal design and performance under load. For heat-run test, the converter needs to be operated at rated voltage and rated current for a substantial length of time. Hence, such tests consume huge amount of energy in case of high-power converters. Also, the capacities of the source and loads available in the research and development (R&D) centre or the production facility could be inadequate to conduct such tests. This paper proposes a method to conduct heat-run tests on high-power, pulse width modulated (PWM) converters with low energy consumption. The experimental set-up consists of the converter under test and another converter (of similar or higher rating), both connected in parallel on the ac side and open on the dc side. Vector-control or synchronous reference frame control is employed to control the converters such that one draws certain amount of reactive power and the other supplies the same; only the system losses are drawn from the mains. The performance of the controller is validated through simulation and experiments. Experimental results, pertaining to heat-run tests on a high-power PWM converter, are presented at power levels of 25 kVA to 150 kVA.

海流-管道-海床之间动力相互作用的量纲分析及实验模拟装置研制=Dimensional Analysis and Experimental Apparatus on Interaction between Ocean Current-Pipeline and Seabed

海底管道涡激振动和管道周围海床冲刷是海流--管道--海床之间复杂的动力耦合问题.文章应用量纲分析方法对海流、管道与海床之间的动力耦合作用进行了分析,确定了在实验模拟中应遵循的相似准则.在此基础上,研制了一套能模拟海流、海床与海底管道之间相互作用的实验模拟装置.初步实验结果表明文中研制的实验模拟装置能够模拟典型海洋环境下海底管道的涡激振动和管道周围海床冲刷等问题.

A possible alchemist apparatus from the early islamic period excavated at Ramla, Israel

Abstract: During extensive salvage excavations carried out during the years 2004-2008 in a large Early Islamic industrial area at the vicinities of Ramla, in Central Israel, an unparalleled industrial device was unearthed. The star-shaped, soil embedded installation, whose lower part was preserved, consisted of a central pottery jar surrounded by five minor jars, linked by ceramic pipes. Evidence of heat was observed mainly around the central vessel, and metal hollow cones perforated in the tip were found inside the surrounding jars. Although the manufacturing procedures and operation techniques of the installation are not completely clear, it is proposed that the installation is part of an industrial workshop or an alchemy laboratory. Both industry and alchemy were well-developed during the Early Islamic period and very often closely related, to the point that sometimes it is difficult to distinguish between them. The identification proposed is based on comparisons with tools described in literary sources, and somewhat later drawings and etchings. Circumstantial ceramic evidence was found, as well as the proximity of a bathhouse whose guests could have been the consumers of perfumes and unguents seem to reinforce this possibility. Due to the poor state of preservation of the device and the lack of available comparisons, the identification proposed here is tentative, and future research coupled with eventual new discoveries is needed in order to clarify this matter.

Performance of a small high-speed liquid jet apparatus

The performance of a small high-speed liquid jet apparatus is described. Water jets of 200m/s to 700m/s have been obtained by firing a deformable lead slug from an air rifle into a stainless steel nozzle containing water sealed with a rubber diaphragm. Nozzle devices of using the impact extrusion (IE) method and cumulation (CU) method are designed to generate jets. The injection sequences are visualized using schlieren photography. The difference between the IE and CU methods in the jet generation is found.

Feeding of larval Cricotopus silvestris F. in relation to characters of structure of oral apparatus [Translation from: C.R.Acad.Sci.USSR.100, 1191-1193, 1955]

Laboratory research was done in order to study the feeding of larval Cricotopus silvestris F. in relation to characters of structure of oral apparatus. Results of the experiments are summarised and the oral apparatus morhologically described.