Análise teórica e experimental de superfícies seletivas de freqüência e suas aplicações em antenas planares

This work presents a theoretical and numerical analysis of structures using frequency selective surfaces applied on patch antennas. The FDTD method is used to determine the time domain reflected fields. Applications of frequency selective surfaces and patch antennas cover a wide area of telecommunications, especially mobile communications, filters and WB antennas. scattering parameters are obteained from Fourier Transformer of transmited and reflected fields in time domain. The PML are used as absorbing boundary condition, allowing the determination of the fields with a small interference of reflections from discretized limit space. Rectangular patches are considered on dielectric layer and fed by microstrip line. Frequency selective surfaces with periodic and quasi-periodic structures are analyzed on both sides of antenna. A literature review of the use of frequency selective surfaces in patch antennas are also performed. Numerical results are also compared with measured results for return loss of analyzed structures. It is also presented suggestions of continuity to this work

VCO Banda Larga Integrado para Receptor a Cinco Portas

This work presents an wideband ring VCO for cognitive radio five-port based receivers. A three-stage differential topology using transmission gate was adopted in order to maintain wide and linear tuning range and a low phase-noise. Monte-Carlo analysis were performed for phase-shift response of individual stages, which is an important figure of merit in five-port works. It was observed a fairly linear correlation between control voltage and oscillation frequency in the range between 200 MHz and 1800 MHz. The VCO was preliminarily designed for IBM 130nm CMOS technology

Análise e projeto de superfícies seletivas em frequência multibanda e/ou banda larga

Frequency selective surfaces (Frequency Selective Surface - FSS) are often used in various applications in telecommunications. Some of these applications may require that these structures have response with multiple resonance bands. Other applications require that the FSS response have large frequency range, to meet the necessary requirements. FSS to design with these features there are numerous techniques cited in the scientific literature. Thus, the purpose of this paper is to examine some common techniques such as: Overlap of FSS; Elements combined; Elements Elements convolucionados and fractals. And designing multiband FSS and / or broadband selecting simple ways in terms of construction and occupy the smallest possible space, aiming at practical applications. Given these requirements, three projects FSS were performed: a technology applied to IEEE 802.11 a/b/g/n and two projects for application in UWB. In project development, commercial software Ansoft DesignerTM and experimental results were satisfactory was used

Estudo da viabilidade econômica para implantação de redes de acesso banda larga em cenários amazônicos: um estudo de caso baseado no custo do bit aplicado ao programa NAVEGAPARÁ

Esta dissertação de mestrado propõe um estudo comparativo relacionado ao custo do bit gerado entre o programa NAVEGAPARÁ e as concessionárias prestadoras do serviço de telecomunicações nos municípios relacionados. Vários estudos são realizados analisando apenas o desempenho de tais sistemas, levando em consideração algumas métricas de avaliação de desempenho, entretanto, não relacionam o custo real para o usuário final. Três cenários reais foram utilizados no estudo de caso. Em cada cenário foi proposta a utilização de uma tecnologia ou mais combinadas para transmissão da informação, levando em consideração, alguns parâmetros como infraestrutura existente, distância entre usuários finais, taxa de transmissão, dentre outros. Algumas tecnologias de acesso, utilizadas neste trabalho, são comparadas com as soluções disponibilizadas pelas concessionárias prestadoras dos serviços existentes e atuantes nos cenários descritos.

Implementazione su fpga di un pre-distorsore digitale a banda larga per sistemi a microonde di backhaul

The development of next generation microwave technology for backhauling systems is driven by an increasing capacity demand. In order to provide higher data rates and throughputs over a point-to-point link, a cost-effective performance improvement is enabled by an enhanced energy-efficiency of the transmit power amplification stage, whereas a combination of spectrally efficient modulation formats and wider bandwidths is supported by amplifiers that fulfil strict constraints in terms of linearity. An optimal trade-off between these conflicting requirements can be achieved by resorting to flexible digital signal processing techniques at baseband. In such a scenario, the adaptive digital pre-distortion is a well-known linearization method, that comes up to be a potentially widely-used solution since it can be easily integrated into base stations. Its operation can effectively compensate for the inter-modulation distortion introduced by the power amplifier, keeping up with the frequency-dependent time-varying behaviour of the relative nonlinear characteristic. In particular, the impact of the memory effects become more relevant and their equalisation become more challenging as the input discrete signal feature a wider bandwidth and a faster envelope to pre-distort. This thesis project involves the research, design and simulation a pre-distorter implementation at RTL based on a novel polyphase architecture, which makes it capable of operating over very wideband signals at a sampling rate that complies with the actual available clock speed of current digital devices. The motivation behind this structure is to carry out a feasible pre-distortion for the multi-band spectrally efficient complex signals carrying multiple channels that are going to be transmitted in near future high capacity and reliability microwave backhaul links.

Progetto e realizzazione di un sistema di test per sensori a effetto hall a banda larga

Un ambito di largo interesse nel campo dell’elettronica, è quello delle misure di corrente a larga banda, in cui la richiesta per sistemi a basso costo è aumentata sensibilmente nel corso del tempo. La causa di questo interessamento è dovuto al più frequente utilizzo di sistemi switched power ad alta frequenza, che necessitano di sensori di correnti isolati e ad alte prestazioni. L’intero lavoro prende in considerazione un sensore di nuova generazione per le misure di corrente, capace di raggiungere prestazioni oltre lo stato dell’arte. L’elaborato presentato vede, quindi, come obiettivo la creazione di un setup stabile per effettuare misure sui chip prodotti. Partendo dallo studio di fattibilità, della componentistica necessaria e dei compromessi per mantenere i costi, si giunge ad una soluzione flessibile e adatta alle misurazioni richieste. L’elaborato partirà con una introduzione sugli effetti fisici e la descrizione del componente fondamentale, passando a test funzionali effettuati su setup provvisori atti a ottenere informazioni basilari per la prosecuzione del lavoro. Infine verranno concepite e realizzate due schede a circuiti stampati per rispondere alle esigenze di progetto.