Usinagem da liga de níquel inconel 718 com pastilhas de cerâmica

The machining of super alloys resistant to high temperatures such as nickel alloys, inconel 718 specifically, is a very difficult job to obtain improvements in the process, due to the difficulty of machining at high cutting speeds, the use of these alloys in industries showed great developments in recent years, its application in aeronautical industry spread being used in vane turbo, compressor parts, props and set elements. The automotive, chemical, medical and others also took advantage of the great features of inconel 718 and has used the material. The high temperature resistant alloys have high machining difficulty, a fact that is associated with high cutting forces generated during machining which result in high temperatures. High levels of temperatures can cause deterioration of the cutting edge, with subsequent deformation or breakage, wear most common obtained in machining such materials are flank wear the formation of built-up edge for cutting and notch wear. The experimental part of the work consists in machining of nickel-based alloy Inconel 718 heat treated for hardness, using a tool based ceramic silicon nitride Sandvik (Si3N4) in order to compare the best results obtained in the master's thesis of SANTOS (2010) who used a tool ceramics also the basis of silicon nitride which was developed in the doctoral thesis of SOUZA (2005). Assays were performed on a CNC lathe and was noted for each cutting edge results obtained. Tests were made starting from an initial condition of the tool with cutting speed of 200 m/min, feed 0.5 mm and 0.5 mm depth of cut was reduced cutting speed for the subsequent tests with the same conditions of feed and depth of cut. The tool presented wear instant under two 200 m/min and 100 m/min, premature rupture of 50 m/min and finally cut provided with difficulty... (Complete abstract click electronic access below)

Na 50 Nachlass Arthur Schopenhauer - 'Schopenhauer-Archiv', 718 - Mitteilung zur geleisteten Unterschrift unter dem Leibrentenvertrag des Bankhauses Muhl

u.a.: Angaben zur erwarteten Rendite; Umzug Arthur Schopenhauers nach Berlin;

Chemistry of interstitial waters of ODP Site 166-718

Preliminary data are presented on dissolved heavy metals in interstitial water samples collected at Site 718 of Ocean Drilling Program Leg 118. The heavy metals at this site are divided into three groups: Group I (B, K, Mn, Ni, Pb, total Si, total P, V) behaves like Mg, which decrease with depth; Group II (Ba, Cu, Sr, Ti) behaves like Ca, which increases with depth; and Group 111 (Cd, Co, Cr, Fe, Na, Mo, Zn) contains metals that are independent of depth. Mg decreases with depth from 50 mM at the seafloor to 21 mM at 900 mbsf. Mn in the sulfate reduction zone (1.0 to 2.8 ppm) is more highly concentrated than in the methane fermentation zone (0.23 to 0.50 ppm), except for Section 116-718-1H-1. A similar behavior is also observed for V and Pb. Ni, B, and K decrease non-uniformly with depth. Ca and Sr increase with depth at the same rates, indicating the dissolution of inorganic calcium carbonate by anaerobic oxidation of organic matter (Sayles, 1981, doi:10.1016/0016-7037(81)90132-0). The distribution of Ba with depth is very similar to those of Ca and Sr. Cu and Ti profiles trend to increase non-uniformly with depth. Fe is constant with depth. The sharp decrease in total silicate concentration at the seafloor probably indicates a decrease in the decomposition of siliceous biological matter (e.g., diatoms) and production of opal. The constant levels of Group 111, except for Na and Fe, may reveal equal sources of supply from surface seawater and the Himalayas over time.

An experimental and numerical study of ductile failure under quasi-static and impact loadings of Inconel 718 nickel-base superalloy

A numerical and experimental study of ballistic impacts at various temperatures on precipitation hardened Inconel 718 nickel-base superalloy plates has been performed. A coupled elastoplastic-damage constitutive model with Lode angle dependent failure criterion has been implemented in LS-DYNA non-linear finite element code to model the mechanical behaviour of such an alloy. The ballistic impact tests have been carried out at three temperatures: room temperature (25 °C), 400 °C and 700 °C. The numerical study showed that the mesh size is crucial to predict correctly the shear bands detected in the tested plates. Moreover, the mesh size convergence has been achieved for element sizes on the same order that the shear bands. The residual velocity as well as the ballistic limit prediction has been considered excellent for high temperature ballistic tests. Nevertheless, the model has been less accurate for the numerical simulations performed at room temperature, being though in reasonable agreement with the experimental data. Additionally, the influence that the Lode angle had on quasi-static failure patterns such as cup-cone and slanted failure has been studied numerically. The study has revealed that the combined action of weakened constitutive equations and Lode angle dependent failure criterion has been necessary to predict the previously-mentioned failure patterns