(Table 1) Experimental shear strength values for IODP Exp315 and Exp316 holes

We investigate the mechanics of slope failures on the Nankai accretionary complex offshore Japan in the vicinity of a major out-of-sequence thrust fault (termed the "megasplay"). Incorporating laboratory-measured shear strength of slope sediments sampled during Integrated Ocean Drilling Project (IODP) Expeditions 315 and 316 with local seafloor slope angles from bathymetric data and constraints on in-situ effective stress conditions from drilling, we find that slopes in the study area are stable and submarine landslides are not expected to occur under static conditions. In order to assess the possibility of slope failure triggered by coseismic rupture of the megasplay fault, we use empirical relations for strong ground motion attenuation from earthquakes with Mw 6-9. We find that the slope sediments should be stable based on computations from one model, developed from a catalog of worldwide subduction zone earthquakes (Youngs et al., 1997, doi:10.1785/gssrl.68.1.58). However, using a different model developed primarily from a catalog of crustal earthquakes in Japan (Kanno et al., 2006, doi:10.1785/0120050138), we find that slopes should be unstable for earthquakes 8 <= Mw <= 9, and possibly unstable for events with 6 <= Mw < 8, depending on the proximity of rupture to the seafloor. Considering limitations of the models and geologic observations of slope failure recurrence, the true slope stability is likely to be in between the predictions of the two models, and we suggest that it may be modulated by long-term pore pressure fluctuations.

Deformation dynamics of SS-316 Between 1023-K TO 1223-K In The Framework of Cottrell-Stokes Law

Kocks' formalism for analysing steady state deformation data for the case where Cottrell-Stokes law is valid is extended to incorporate possible back stresses from solution and/or precipitation hardening, and dependence of pre-exponential factor on the applied stress. A simple graphical procedure for exploiting these equations is demonstrated by analyzing tensile steady state data for a type 316 austentic stainless steel for the temperature range 1023 to 1223 K. In this instance, the computed back stress values turned out to be negative, a physically meaningless result. This shows that for SS 316, deformation in this temperature regime can not be interpreted in terms of a mechanism that obeys Cottrell-Stokes law.

Investigation on the High Vacuum Tribological Characteristics of Surface Treated Nuclear Grade Stainless Steel Type AISI 316 LN at 25 to 500 degrees C

Although some researchers have published friction and wear data of Plasma Nitride (PN) coatings, the tribological behavior of PN/PN Pairs in high vacuum environment has not been published so far In order to bridge this knowledge gap, tribological tests under dry conditions have been conducted on PN/PN Pairs for varying temperatures of 25, 200, 400 and 500 degrees C in high vacuum (1.6 x 10(-4) bar) environment. The PN coatings showed good wear resistance layer on the ring surface. The PN coatings were removed only from the pin surface for all the tests since it contacts at a point. The friction and wear were low at lower temperatures and it eliminated adhesion between the contact surfaces until the coating was completely removed from the pin surface. (C) 2011 Journal of Mechanical Engineering. All rights reserved.

Mixed-mode fracture mechanisms near the fatigue threshold of aisi-316 stainless-steel

Near threshold, mixed mode (I and II), fatigue crack growth occurs mainly by two mechanisms, coplanar (or shear) mode and branch (or tensile) mode. For a constant ratio of ΔK_I/ΔK_II the shear mode growth shows a self-arrest character and it would only start again when ΔK_I and ΔK_II are increased. Both shear crack growth and the early stages of tensile crack growth, are of a crystallographic nature; the fatigue crack proceeds along slip planes or grain boundaries. The appearance of the fracture surfaces suggest that the mechanism of crack extension is by developing slip band microcracks which join up to form a macrocrack. This process is thought to be assisted by the nature of the plastic deformation within the reversed plastic zone where high back stresses are set up by dislocation pile-ups against grain boundaries. The interaction of the crack tip stress field with that of the dislocation pile-ups leads to the formation of slip band microcracks and subsequent crack extension. The change from shear mode to tensile mode growth probably occurs when the maximum tensile stress and the microcrack density in the maximum tensile plane direction attain critical values.

Diário da Constituinte [gravação de vídeo] : [programa n. 316]

Conclusão das votações na Comissão de Sistematização. Na discussão sobre Anisitia, foram rejeitadas as propostas que previam o pagamento de atrasados aos anistiados. Uma delas foi a emenda do Deputado Brandão Monteiro (PDT-RJ), que estendia os benefícios da Anistia aos membros da Marinha e Aeronáutica. Aprovada emenda do Deputado José Maria Eymael (PDC-SP) estabelecendo que a lei ordinária irá criar uma compesação financeira para os pilotos da Força Aérea Brasileira (FAB) cassados depois de março de 1964. Aprovado destaque do Deputado José Costa (PMDB-AL), que possibilita às vítimas cassadas após 1964, recorrerem à justiça para terem seus direitos revistos. A Anistia foi também estendida aos trabalhadores do setor privado com a emenda do Deputado João Paulo Vasconcellos (PT-MG). Aprovada a emenda de Nelson Carneiro (PMDB-RJ), que regula a aplicação do parlamentarismo nos Estados. A Deputada Raquel Cândido (PFL-RO) tem a sua emenda aprovada, que cria o Código de Defesa do Consumidor. A duração do mandato do Presidente José Sarney gera polêmica entre os constituintes. Opinam os Deputados: Elizer Moreira (PFL-MA), João Carlos Barcelar (PMDB-BA) e João Hermann Neto (PMDB-SP).