Low temperature response of nanostructured tungsten oxide thin films toward hydrogen and ethanol

Semiconducting metal oxide based gas sensors usually operate in the temperature range 200–500 °C. In this paper, we present a new WO3 thin film based gas sensor for H2 and C2H5OH, operating at 150 °C. Nanostructured WO3 thin films were synthesized by thermal evaporation method. The properties of the as-deposited films were modified by annealing in air at 300 °C and 400 °C. Various analytical techniques such as AFM, TEM, XPS, XRD and Raman spectroscopy have been employed to characterize their properties. A clear indication from TEM and XRD analysis is that the as-deposited WO3 films are highly amorphous and no improvement is observed in the crystallinity of the films after annealing at 300 °C. Annealing at 400 °C significantly improved the crystalline properties of the films with the formation of about 5 nm grains. The films annealed at 300 °C show no response to C2H5OH (ethanol) and a little response to H2, with maximum response obtained at 280 °C. The films annealed at 400 °C show a very good response to H2 and a moderate response to C2H5OH (ethanol) at 150 °C. XPS analysis revealed that annealing of the WO3 thin films at 400 °C produces a significant change in stoichiometry, increasing the number of oxygen vacancies in the film, which is highly beneficial for gas sensing. Our results demonstrate that gas sensors with significant performance at low operating temperatures can be obtained by annealing the WO3 films at 400 °C and optimizing the crystallinity and nanostructure of the as-deposited films.

Stochastic demography and population dynamics in the red kangaroo Macropus rufus

1. Many organisms inhabit strongly fluctuating environments but their demography and population dynamics are often analysed using deterministic models and elasticity analysis, where elasticity is defined as the proportional change in population growth rate caused by a proportional change in a vital rate. Deterministic analyses may not necessarily be informative because large variation in a vital rate with a small deterministic elasticity may affect the population growth rate more than a small change in a less variable vital rate having high deterministic elasticity. 2. We analyse a stochastic environment model of the red kangaroo (Macropus rufus), a species inhabiting an environment characterized by unpredictable and highly variable rainfall, and calculate the elasticity of the stochastic growth rate with respect to the mean and variability in vital rates. 3. Juvenile survival is the most variable vital rate but a proportional change in the mean adult survival rate has a much stronger effect on the stochastic growth rate. 4. Even if changes in average rainfall have a larger impact on population growth rate, increased variability in rainfall may still be important also in long-lived species. The elasticity with respect to the standard deviation of rainfall is comparable to the mean elasticities of all vital rates but the survival in age class 3 because increased variation in rainfall affects both the mean and variability of vital rates. 5. Red kangaroos are harvested and, under the current rainfall pattern, an annual harvest fraction of c. 20% would yield a stochastic growth rate about unity. However, if average rainfall drops by more than c. 10%, any level of harvesting may be unsustainable, emphasizing the need for integrating climate change predictions in population management and increase our understanding of how environmental stochasticity translates into population growth rate.

Water and thermal regimes for field pea in Australia and their implications for breeding.

There is a large gap between the refined approaches to characterise genotypes and the common use of location and season as a coarse surrogate for environmental characterisation of breeding trials. As a framework for breeding, the aim of this paper is quantifying the spatial and temporal patterns of thermal and water stress for field pea in Australia. We compiled a dataset for yield of the cv. Kaspa measured in 185 environments, and investigated the associations between yield and seasonal patterns of actual temperature and modelled water stress. Correlations between yield and temperature indicated two distinct stages. In the first stage, during crop establishment and canopy expansion before flowering, yield was positively associated with minimum temperature. Mean minimum temperature below similar to 7 degrees C suggests that crops were under suboptimal temperature for both canopy expansion and radiation-use efficiency during a significant part of this early growth period. In the second stage, during critical reproductive phases, grain yield was negatively associated with maximum temperature over 25 degrees C. Correlations between yield and modelled water supply/demand ratio showed a consistent pattern with three phases: no correlation at early stages of the growth cycle, a progressive increase in the association that peaked as the crop approached the flowering window, and a progressive decline at later reproductive stages. Using long-term weather records (1957-2010) and modelled water stress for 104 locations, we identified three major patterns of water deficit nation wide. Environment type 1 (ET1) represents the most favourable condition, with no stress during most of the pre-flowering phase and gradual development of mild stress after flowering. Type 2 is characterised by increasing water deficit between 400 degree-days before flowering and 200 degree-days after flowering and rainfall that relieves stress late in the season. Type 3 represents the more stressful condition with increasing water deficit between 400 degree-days before flowering and maturity. Across Australia, the frequency of occurrence was 24% for ET1, 32% for ET2 and 43% for ET3, highlighting the dominance of the most stressful condition. Actual yield averaged 2.2 t/ha for ET1, 1.9 t/ha for ET2 and 1.4 t/ha for ET3, and the frequency of each pattern varied substantially among locations. Shifting from a nominal (i.e. location and season) to a quantitative (i.e. stress type) characterisation of environments could help improving breeding efficiency of field pea in Australia.

Direction of arrival estimation in the presence of distributed noise sources: Cumulant based approach

In the past few years there have been attempts to develop subspace methods for DoA (direction of arrival) estimation using a fourth?order cumulant which is known to de?emphasize Gaussian background noise. To gauge the relative performance of the cumulant MUSIC (MUltiple SIgnal Classification) (c?MUSIC) and the standard MUSIC, based on the covariance function, an extensive numerical study has been carried out, where a narrow?band signal source has been considered and Gaussian noise sources, which produce a spatially correlated background noise, have been distributed. These simulations indicate that, even though the cumulant approach is capable of de?emphasizing the Gaussian noise, both bias and variance of the DoA estimates are higher than those for MUSIC. To achieve comparable results the cumulant approach requires much larger data, three to ten times that for MUSIC, depending upon the number of sources and how close they are. This is attributed to the fact that in the estimation of the cumulant, an average of a product of four random variables is needed to make an evaluation. Therefore, compared to those in the evaluation of the covariance function, there are more cross terms which do not go to zero unless the data length is very large. It is felt that these cross terms contribute to the large bias and variance observed in c?MUSIC. However, the ability to de?emphasize Gaussian noise, white or colored, is of great significance since the standard MUSIC fails when there is colored background noise. Through simulation it is shown that c?MUSIC does yield good results, but only at the cost of more data.

Synthesis of isotactic polystyrene with a rare-earth catalyst

Polymerization of styrene with the neodymium phosphonate Nd(P-507)/H2O/Al(i-Bu)(3) catalytic system has been examined. The polymer obtained was separated into a soluble and an insoluble fraction by 2-butanone extraction. C-13-NMR spectra indicate that the insoluble fraction is isotactic polystyrene and the soluble one is syndiotactic-rich atactic polystyrene. The polymerization features are described and discussed. The optimum conditions for the polymerization are as follows: [Nd] = (3.5-5.0) x 10(-2) mol/L; [styrene] = 5 mol/L; [Al]/[Nd] = 6-8 mol/mol; [H2O]/[Al] = 0.05-0.08 mol/mol; polymerization temperature around 70 degrees C. The percent yield of isotactic polystyrene (TY) is markedly affected by catalyst aging temperature. With increase of the aging temperature from 40 to 70 degrees C, TY increases from 9% to 48%. Using AlEt3 and Al(i-Bu)(2)H instead of Al(i-Bu)(3) decreases the yield of isotactic polystyrene. Different neodymium compounds give the following activity order: Nd(P-507)(3) > Nd(P-204)(3) > Nd(OPri)(3) > NdCl3 + C2HF5OH > Nd(naph)(3). With Nd(naph)(3) as catalyst, only atactic polystyrene is obtained. (C) 1998 John Wiley & Sons, Inc.

THE COMPOSITIONS AND STRUCTURES OF SOME COMPOUNDS IN THE SYSTEM CA-SR-CU-O

The system of Ca-Sr-Cu-O have been investigated. Two new compounds with compositions Sr3Cu5O8+alpha and CaSrCu3O5+alpha have been discovered. Both are orthorhombic with a = 6.489, b = 11.280, c = 12.240 angstrom for CaSrCu3O5+alpha and a = 3.950, b = 11.479, c = 13.420 angstrom for Sr3Cu5O8+alpha. The X-ray powder data for CaSrCu3O5+alpha, Sr3Cu5O8+alpha, Sr2CuO3 and SrCuO2 are presented. The oxidation state of Cu ion and oxygen contents are analyzed by iodometric titration. Sr0.5Ca0.5CuO2 that has a similar structure with SrCuO2 has been found and its X-ray data are presented also.

Ca-Sr-Cu-O系中若干化合物的组成和结构的研究

研究了Ca-Sr-Cu-O三元金属复合氧化物体系,发现了两个新化合物Sr_3Cu_5O_(8+x)和CaSrCu_3·O_(5+x),两者都属正交晶系,前者a=3.950,b=11479,c=13.420 A.后者a=6.489,b=11.280,c=12.240A.文中给出了这两个化合物和SrCuO_2、Sr_2CuO_3的XRD谱.用碘量法测定了化合物中的氧含量.此外还发现了结构与SrCuO_2相似的固溶体Sr_(0.5)Ca_(0.5)CuO_2,也测定了它的XRD谱.

天然有机质与多环芳烃相互作用的荧光光谱学研究—以苝、菲和蒽为例

自然界水体（如地下水、湖泊、河流及海洋）中的天然有机质（NOM）因具有显著的生态及环境功能而受到人们的广泛关注。NOM作为全球碳循环的主要组成部分，是水体中异养型微生物生长所需碳及能量的重要来源。此外，NOM对湖泊生态系统中的多种物理、化学过程具有不同程度的影响：NOM中的有机酸对淡水体系的酸度具有控制作用而且对酸沉降有一定的缓冲作用；NOM通过减弱可见光及紫外线照射从而影响淡水系统的光化学环境，这一方面降低了水体中自养生物的繁衍速度，同时保护水生生物免受有害的紫外线辐射。更为重要的是，NOM能够影响环境中污染物的命运，比如重金属离子和疏水性有机污染物与天然有机质结合后，其迁移途径、溶解度、生物可利用性及毒性受到明显的控制，这样其对环境中生物的危害性减弱。多环芳烃（PAHs）是一类对环境危害极大的疏水性有机污染物，多数PAHs对有机体具有毒性和致癌性而被美国环保署（EPA）列为优先处理的污染物。因此，确定NOM-PAHs反应的强弱，即PAHs在NOM中的分配系数（Kdoc）以及NOM的物化特性对Kdoc的影响对于预测PAHs毒性和生物可利用性大小、了解NOM-PAHs相互作用的机理及确立污染预测模型具有十分重大的意义。前人的研究结果表明，多环芳烃与天然有机质相互作用的分配系数Kdoc的与PAHs的疏水度（即Kow大小）、NOM的物化特性（如芳香度、脂肪碳含量、分子量及极性等）和水化学参数（pH、离子强度等）有很大的相关性。然而，许多学者在NOM的物化特性对分配系数的影响方面存有较大分歧。前人在研究天然有机质与多环芳烃之间的相互作用时所用的NOM多为腐殖质，即水体NOM中的疏水性组分，而其中的亲水性组分与PAHs的结合作用文献中却鲜见提及，因此人们对其结合作用的特性如反应机理和结合作用强弱等的了解十分有限。 本论文利用XAD树脂分离技术把红枫湖水体中天然有机质分成了疏水性酸、碱、中性物质和亲水性酸、碱、中性物质等六种有机组分。同时运用元素分析、有机碳分析仪、紫外－可见分光光度，高效液相体积排阻色谱、三维荧光光谱和荧光偏振技术等现代分析方法，对各有机组分的物理、化学特性进行了表征。荧光光谱技术被用于研究水化学参数对腐殖质荧光特性和分子构型的影响以及测定Amherst腐殖酸（Amherst HA）、垃圾渗滤液富里酸（LF FA）和红枫湖NOM有机组分与多环芳烃苝、菲和蒽的结合系数（分配系数、条件稳定常数）并探讨了影响分配系数的各种因素和NOM与多环芳烃相互作用的机理。本论文的获得的主要结果如下： 1. 在水化学参数对腐殖质荧光特性及分子构型的影响方面： 在NOM与PAHs相互作用过程中，腐殖质的分子构型起着关键性的作用，而其分子构型又受到其本身的浓度、溶液的pH和离子强度等水化学参数的影响。本论文运用三维荧光光谱和荧光偏振技术研究了水化学参数对腐殖质荧光特性的影响，并由此推断其分子构型变化情况。实验结果表明随着腐殖质浓度、溶液的pH和离子强度的改变，腐殖质荧光特性（如荧光强度、荧光峰位和荧光偏振值等）出现不同程度的变化，揭示了腐殖质分子构型的改变。因此，本实验结果有利于深入了解腐殖质的分子构型及其对吸附PAHs的重要影响，对理解NOM的环境行为具有一定的理论价值。 2. 运用荧光猝灭滴定法研究Amherst HA和红枫湖NOM有机组分对多环芳烃苝、菲和蒽的吸附作用，结果表明NOM对多环芳烃的吸附能力与其中芳香结构单元有很强的相关性，logKdoc值与NOM在280 nm处的摩尔吸收（ε280）和分子量有线性度较高的正比关系，而C/H原子比值对不饱和碳含量（芳香度）并没有很好的指示作用。同时，脂肪碳（0－50 ppm）中的聚亚甲基碳对吸附PAHs也有很大的贡献，而有机组分的极性与分配系数有明显的负相关性。不同种类的多环芳烃与NOM有机组分的结合能力有很大的差异，这取决于不同PAHs的疏水度大小。本研究结果有利于弥合前人在NOM物化特性对PAHs吸附能力的影响方面的分歧，揭示了NOM的组成和结构在与PAHs等疏水性有机污染物相互作用方面的重要影响。 3. 在结合机理方面，苝与NOM有机组分结合的Stern－Volmer图具有较高的线性度，这表明其结合机理以疏水反应（或分配）为主，而菲和蒽与有机组分相互作用的吸附等温线显示较多的非线性特征表明极性反应为主要反应机理，结合过程以吸附为主。在红枫湖NOM有机组分中，疏水性组分显示对PAHs较高的结合能力，同时疏水性组分与PAHs相互作用的吸附等温线具有较高的线性度。这一结果揭示了不同种类的PAHs和各NOM有机组分之间结合机理的差异，加深了人们对NOM与PAHs相互作用机理的认识。 4. 前人在研究pH、离子强度等水化学参数对分配系数的影响方面得到的结果多有矛盾之处，同时，对实验结果的解释也不尽相同。本实验结果表明分配系数随pH增加而下降；离子强度对分配系数的影响比较复杂，就总体趋势而言，增加离子强度有利于对PAHs吸附能力的提高，这一结果初步揭示了水化学参数对PAHs分配系数的影响，丰富了人们对其影响机理的认识。 5. 运用荧光偏振技术测定了蒽与Amherst HA、LF FA和红枫湖NOM有机组分的条件稳定常数，结果如下：随着NOM浓度增加，蒽的荧光偏振值不断下降，这表明蒽的分子构型由平面线性向圆柱状转变。在所有NOM样品中，土壤源的Amherst HA与蒽结合的条件稳定常数最大（pH 4时logK=5.6，pH 6时 logK=5.4）；就NOM有机组分而言，疏水性组分的logK变化范围在pH 6时为（4.4－5.2），而亲水性组分为（4.3－4.8），这表明疏水性组分具有相对较高的蒽吸附能力。实验结果有利于了解PAHs与NOM相互作用前后的分子构型变化情况，揭示了不同的NOM有机组分在吸附PAHs过程中的差异。

Hydrolysis characteristics and kinetics of waste hay biomass as a potential energy crop for fermentable sugars production using autoclave parr reactor system

The use of the organic fraction of municipal solid waste crops has received considerable attention as a sustainable feedstock that can replace fossil fuels for the production of renewable energy. Therefore, municipal bin-waste in the form of hay was investigated as a potential energy crop for fermentable sugars production. Hydrolysis of hay by dilute phosphoric acid was carried out in autoclave parr reactor, where reactor temperature (135-200 degrees c) and acid concentration (2.5-10% (w/w)) were examined. Analysis of the decomposition rate of hemicellulosic biomass was undertaken using HPLC of the reaction products. Xylose production reached a maximum value of 13.5 g/100 g dry mass corresponding to a yield of 67% at the best identified conditions of 2.5 wt% H3PO4, 175 degrees C, 10 min reaction time, and at 5 wt% H3PO4, 150 degrees C, and 5 min reaction time. For glucose, an average yield of 25% was obtained at 5 wt% H3PO4, 175 degrees C and 30 min. Glucose degradation to HMF was achieved at 10 wt% H3PO4 and 200 degrees C. The maximum yield for produced arabinose was an average of 3 g/100 g dry. mass corresponding to 100% of the total possible arabinose. The kinetic study of the acid hydrolysis was also carried out using the Saeman and the Two-fraction models. It was found for both models that the kinetic constants (k) depend on the acid concentration and temperature. For xylose and arabinose it was found that the rate of formation was more favoured than the rate of degradation. By contrast, for glucose it was found that glucose degradation was occurring faster than glucose formation. It can be concluded that dilute phosphoric acid hydrolysis of hay crop is feasible for the production of fermentable sugars which are essential for bioethanol synthesis. 

Effects of corn silage derived from a genetically modified variety containing two Transgenes on feed intake, milk production, and composition, and the absence of detectable Transgenic deoxyribonucleic acid in milk in holstein dairy cows

The objectives were to compare the chemical composition, nutritive value, feed intake, milk production and composition, and presence in milk of transgenic DNA and the encoded protein Cry1Ab when corn silages containing 2 transgenes (2GM: herbicide tolerance: mepsps and insect resistance: cry1Ab) were fed as part of a standard total mixed ration (TMR) compared with a near isogenic corn silage ( C) to 8 multiparous lactating Holstein dairy cows in a single reversal design study. Cows were fed a TMR ration ad libitum and milked twice daily. Diets contained [ dry matter (DM) basis] 45% corn silage, 10% alfalfa hay, and 45% concentrate (1.66 Mcal of net energy for lactation/kg of DM, 15.8% crude protein, 35% neutral detergent fiber, and 4.1% fat). Each period was 28-d long. During the last 4 d of each period, feed intake and milk production data were recorded and milk samples taken for compositional analysis, including the presence of transgenic DNA and Cry1Ab protein. There was no significant difference in the chemical composition between C and 2GM silages, and both were within the expected range (37.6% DM, 1.51 Mcal of net energy for lactation/kg, 8.6% crude protein, 40% neutral detergent fiber, 19.6% acid detergent fiber, pH 3.76, and 62% in vitro DM digestibility). Cows fed the 2GM silage produced milk with slightly higher protein (3.09 vs. 3.00%), lactose ( 4.83 vs. 4.72%) and solids-not-fat (8.60 vs. 8.40%) compared with C. However, the yield (kg/d) of milk (36.5), 3.5% fat-corrected milk (34.4), fat (1.151), protein (1.106), lactose (1.738), and solids-not-fat ( 3.094), somatic cell count (log(10): 2.11), change in body weight (+ 7.8 kg), and condition score (+ 0.09) were not affected by type of silage, indicating no overall production difference. All milk samples were negative for the presence of transgenic DNA from either trait or the Cry1Ab protein. Results indicate that the 2GM silage modified with 2 transgenes did not affect nutrient composition of the silages and had no effect on animal performance and milk composition. No transgenic DNA and Cry1Ab protein were detected in milk.

Mass transport effects in the borohydride oxidation reaction-Influence of the residence time on the reaction onset and faradaic efficiency

The borohydride oxidation reaction (BOR) was studied on Pt and Au electrodes by cyclic voltammetry in dilute alkaline borohydride solutions (0.1 M NaOH + 10(-3) mol L(-1) NaBH(4)). More specifically, the electrodes were considered as either Vulcan XC72-supported Pt or Au (noted as Pt/C and Au/C, respectively) active layers or smooth Pt or Au surfaces, the latter possibly being covered by a layer of (non-metalized) Vulcan XC72 carbon powder. The BOR onset potential and the number of electrons (n(e-)) exchanged per BH(4)(-) anion (faradaic efficiency) were investigated for these electrodes, to determine whether the residence time of reaction intermediates (at the electrode surface or inside the porous layer) does influence the overall reaction pathway/completion. For the carbon-supported platinum, n(e-) strongly depends on the thickness of the active layer. While thin (ca. 0.5 mu m-thick) Pt/C active layers yield n(e-) < 4, thick layers (approximately 3 mu m) yield n(e-)approximate to 8, which can be ascribed to the sufficient residence time of the molecules formed within the active layer (H(2), by heterogeneous hydrolysis, or BOR intermediates) enabling further (near-complete) oxidation. This puts into evidence that not only the nature of the electrocatalyst is important to reach high BOR efficiency, but also the structure/thickness of the active layer. The same trend applies for Au/C active layers and for smooth Pt or Au surfaces covered with a layer of (inactive) Vulcan XC72. In addition, the BOR onset usually shifts negative when the reaction intermediates are trapped, which suggests that some of the intermediates are more easily oxidized than BH(4)(-) itself; based on literature data, BH(3)OH(-) species is a likely candidate. (C) 2011 Elsevier B.V. All rights reserved.

Incorporação de resíduo cerâmico para prevenção da retrogressão da resistência de cimentos de poços de petróleo submetidos à injeção de vapor

Steam injection is the most used thermal recovery method of oil nowadays because of the high degree of development of the technique that allows high recovery factors. However, injection of superheated steam into the reservoir affects the entire structure of the well, including the cemented layer that presents a retrogression of compressive strength and increases the permeability due to formation of more crystalline and denser phases at temperatures above 110 °C. These changes result in failures in the cement that favor the entrance of formation fluids into the annulus space resulting in unsafe operations and restrictions in the economic life of the well. But the strength retrogression can be prevented by partial replacement of cement by silica-based materials that reduce the CaO/SiO2 ratio of cement slurries changing the trajectory of the reactions, converting those deleterious phases in phases with satisfactory mechanical strength and permeability. The aim of this study was to evaluate the behavior of a ceramic waste material rich in silica in partial and total substitution of a mineral additive used to fight the strength retrogression of cement slurries subjected to high temperatures. The evaluation was made by compression, X-ray diffraction (XRD) and thermogravimetry (TG/DTG). The samples were submitted to a cycle of low temperature (38 °C) for 28 days and a cycle of low temperature followed by exposure to 280 ºC and 1000 psi by 3 days. The results showed that slurries with additions of up to 30% of the waste material are not enough to prevent the strength retrogression, while slurries with additions of the waste material combined with silica flour in various proportions produced hydrated products of low Ca/Si ratios that maintained the compressive strength at satisfactory levels

Isomaltulose production from Sucrose by Protaminobacter rubrum immobilized in calcium alginate

Different culture conditions for Protaminobacter rubrum and enzymatic reaction parameters were evaluated with the goal of improving isomaltulose production. P. rubrum was grown in a medium with 1% (w/v) cane molasses and 0.5% yeast extract and achieved a maximum cell yield Y(x/s) of 0.295 g of cells/g sucrose and a specific growth rate (mu) of 0.192 h(-1). The immobilization of P. rubrum cells was carried out with calcium alginate, glutaraldehyde and polyethyleneimine. Stabile immobilized cell pellets were obtained and used 24 times in batch processes. Enzymatic conversion was carried out at different sucrose concentrations and in pH 6 medium with 70% (w/v) sucrose at 30 degrees C an isomaltulose yield of 89-94% (w/v) was obtained. The specific activity of the P. rubrum immobilized pellets in calcium alginate at 30 degrees C ranged from 1.6 to 4.0 g isomaltulose g(-1) pellet h(-1), respectively with 70% and 65% sucrose solution, while in lower sucrose concentration had higher specific activities presumably due to substrate inhibition of the isomaltulose synthase in higher sucrose concentrations. (C) 2009 Elsevier Ltd. All rights reserved.

Thermotropic phase behavior in aqueous mixtures of dioctadecyldimethylammonium bromide and alkyltrimethylammonium bromide surfactant series studied by differential scanning calorimetry

The effect of the micelle-forming surfactant series alkyltrimethylammonium bromide (C(n)TAB, n = 12, 14, 16 and 18) on the thermotropic phase behavior of dioctadecyldimethylammonium bromide (DODAB) vesicles in water was investigated by differential scanning calorimetry at constant 5.0 mM total surfactant concentration and varying individual surfactant concentrations. The pre-, post- and main transition temperatures (T-s, T-p and T-m), melting enthalpy (Delta H) and peak width of the main transition (Delta T-1/2) are reported as a function of the surfactant molar fraction. No clear dependence of these parameters on the C(n)TAB chain length was found. At 5 mM, neat DODAB in water exhibits two transition temperatures, T-s = 32.1 and T-m = 42.7 degrees C, as obtained from the DSC upscans, but not a clear T-p. For every n, except n = 12, T-s vanishes as CnTAB concentration increases and approaches CMC. T-m behaves differently for different n, the longer C(14)TAB and C(16)TAB decrease, while C(18)TAB increases T-m with increasing concentration. The data indicate that changes in T-m, T-s, T-p and Delta H of the transition are related not only to the extent of C(n)TAB affinity to DODAB but also to the surfactant chain length. Accordingly, C18TAB yields a more compact bilayer, thus increasing T-m, while C(14)TAB and C(1G)TAB yield a less organized bilayer and reduce T-m. C(12)TAB does not much affect T-s and T-m, although it yields T-p approximate to 51.6 degrees C. (C) 2008 Elsevier B.V. All rights reserved.

Composition of coriander essential oil from Brazil

Coriander (Coriandrum sativum L.) is an annual and herbaceous plant, belonging to the Apiaceae family. Native of southern Europe and western Mediterranean region, this herb is cultivated world widely. This species, rich in linalool, has potential using as source of essential oil and as a medicinal plant. It has been used as analgesic, carminative, digestive, depurative, anti-rheumatic and antispasmodic agent. Its fruits (commonly called seeds) are used for flavoring candies, in cookery, perfumery, beverage and in tobacco industry. The aim of this study was to analyze the chemical composition of the seed essential oil of this species grown in Botucatu, São Paulo, Brazil. The experiment was carried out in Lageado Experimental Farm, Department of Plant Production, Agronomical Sciences College, São Paulo State University. The fruits were harvest 108 days after sowing. The essential oils were extracted by hydro distillation, in Clevenger apparatus. 50 g of fruits were used in each extraction. Three extractions were performed during three hours. The essential oils were analyzed in Gas Chromatography Mass Spectrometer (CG-MS, Shimadzu, QP-5000), equipped with DB-5 capillary column (30 m × 0,25 mm × 0,25 mm), split 1/20, injector for 240 C°, detector for 230 C°, dragged by gas He (1,7 mL/min), with programmed temperature for 40 C° (5 min)-150 C°, 4 C°/min; 150 C°-280 C°, 8 C°/min. The identification of the compounds was made by comparison of their spectra of masses with data from CG-MS (Nist 62 lib), literature references and retention index of Kovats. The 18 most important components were identified and quantified. The main components of the oil were linalool (77.48 %), γ-terpinene (4.64 %), α-pinene (3.97 %), limonene (1.28 %), geraniol (0.64 %) and 2-decenal (0.16 %).