Une évaluation de la dimension de la lumière de boîtiers 0,018" provenant de quatre différents manufacturiers. Existe-t-il un standard dans l’industrie?

Introduction: The objective of this experimental research was to evaluate the slot’s vertical dimension and profile of four different 0.018″ self-ligating brackets and to identify the level of tolerance accepted by manufacturers during the fabrication process. It was then possible to calculate and compare the torque play of those brackets using the measured values and the nominal values. Material and Methods: Twenty-five 0.018″ self-ligating brackets of upper left central incisors from the following manufacturers, Speed® (Strite Industries, Cambridge, Ontario, Canada), InOvationR® (GAC, Bohemia, NY, USA), CarriereLX® (Ortho Organizers, Carlsbad, CA, USA) and SmartClip® (3M Unitek, Monrovia, CA, USA), were evaluated using electron microscopy with 150X images. The height of each bracket was measured at every 100 microns of depth from the lingual wall at five different levels. A Student T test was then used to compare our results with the manufacturer’s stated value of 0.018″. To determine if there was a significant difference between the four manufacturers, analysis of variance (ANOVA) was performed at the significance level of p<0.05. The torque play was then calculated using geometrical formulas. Results: On average, Speed brackets were oversized by 2.7%[MV 0.0185″ (SD:0.002)], InOvationR by 3.7% [MV 0.0187″ (SD:0.002)], CarriereLX by 3.2% [MV 0.0186″ (SD:0.002)] and SmartClipSL by 5.0% [MV 0.0189″ (SD:0.002)]. The height of all brackets was significantly higher than the nominal value of 0.018″ (p<0.001). The slot of SmartClip brackets was significantly larger than those of the other three manufacturers (p<0.001). None of the brackets studied had parallel gingival and occlusal walls; some were convergent and others divergent. These variations can induce a torque play up to 4.5 degrees with a 0.017″x0.025″ wire and 8.0 degrees with a 0.016″x0.022″ wire. Conclusion: All studied brackets were oversized. None of the brackets studied had parallel gingival and occlusal walls and there was no standard between manufacturers for the geometry of their slots. These variations can cause a slight increase of the torque play between the wire and the bracket compared with the nominal value.

Sostenibilidad y seguridad de abastecimiento eléctrico: estudio de caso sobre Chile con posterioridad a la ley 20.018

Incluye Bibliografía

Torque expression of 0.018 and 0.022 inch conventional brackets

The aim of this study was to assess the effect of the moments generated with low- and high-torque brackets. Four different bracket prescription-slot combinations of the same bracket type (Mini Diamond® Twin) were evaluated: high-torque 0.018 and 0.022 inch and low-torque 0.018 and 0.022 inch. These brackets were bonded on identical maxillary acrylic resin models with levelled and aligned teeth and each model was mounted on the orthodontic measurement and simulation system (OMSS). Ten specimens of 0.017 × 0.025 inch and ten 0.019 × 0.025 inch stainless steel archwires (ORMCO) were evaluated in the low- and high-torque 0.018 inch and 0.022 inch brackets, respectively. The wires were ligated with elastomerics into the brackets and each measurement was repeated once after religation. Two-way analysis of variance and t-test were conducted to compare the generated moments between wires at low- and high-torque brackets separately. The maximum moment generated by the 0.017 × 0.025 inch stainless steel archwire in the 0.018 inch brackets at +15 degrees ranged from 14.33 and 12.95 Nmm for the high- and low-torque brackets, respectively. The measured torque in the 0.022 inch brackets with the 0.019 × 0.025 inch stainless steel archwire was 9.32 and 6.48 Nmm, respectively. The recorded differences of maximum moments between the high- and low-torque series were statistically significant. High-torque brackets produced higher moments compared with low-torque brackets. Additionally, in both high- and low-torque configurations, the thicker 0.019 × 0.025 inch steel archwire in the 0.022 inch slot system generated lower moments in comparison with the 0.017 × 0.025 inch steel archwire in the 0.018 inch slot system.

Torque efficiency of different archwires in 0.018- and 0.022-inch conventional brackets.

OBJECTIVE To compare the archwires inserted during the final stages of the orthodontic treatment with the generated moments at 0.018- and 0.022-inch brackets. MATERIALS AND METHODS The same bracket type, in terms of prescription, was evaluated in both slot dimensions. The brackets were bonded on two identical maxillary acrylic resin models, and each model was mounted on the orthodontic measurement and simulation system. Ten 0.017 × 0.025-inch TMA and ten 0.017 × 0.025-inch stainless steel archwires were evaluated in the 0.018-inch brackets. In the 0.022-inch brackets, ten 0.019 × 0.025-inch TMA and ten 0.019 × 0.025-inch stainless steel archwires were measured. A 15° buccal root torque (+15°) and then a 15° palatal root torque (-15°) were gradually applied to the right central incisor bracket, and the moments were recorded at these positions. A t-test was conducted to compare the generated moments between wires within the 0.018- and 0.022-inch bracket groups separately. RESULTS The 0.017 × 0.025-inch archwire in the 0.018-inch brackets generated mean moments of 9.25 Nmm and 14.2 Nmm for the TMA and stainless steel archwires, respectively. The measured moments in the 0.022-inch brackets with the 0.019 × 0.025-inch TMA and stainless steel archwires were 6.6 Nmm and 9.3 Nmm, respectively. CONCLUSION The 0.017 × 0.025-inch stainless steel and β-Ti archwires in the 0.018-inch slot generated higher moments than the 0.019 × 0.025-inch archwires because of lower torque play. This difference is exaggerated in steel archwires, in comparison with the β-Ti, because of differences in stiffness. The differences of maximum moments between the archwires of the same cross-section but different alloys were statistically significant at both slot dimensions.