The epidemiologic paradox of low birth weight in Brazil

OBJECTIVE: To examine whether the low birth weight (LBW) paradox exists in Brazil. METHODS: LBW and cesarean section rates between 1995 and 2007 were estimated based on data from SINASC (Brazilian Live Births Database). Infant mortality rates (IMRs) were obtained using an indirect method that correct for underreporting. Schooling information was obtained from census data. Trends in LBW rate were assessed using joinpoint regression models. The correlations between LBW rate and other indicators were graphically assessed by lowess regression and tested using Spearman's rank correlation. RESULTS: In Brazil, LBW rate trends were non-linear and non-significant: the rate dropped from 7.9% in 1995 to 7.7% in 2000, then increased to 8.2% in 2003 and remained nearly steady thereafter at 8.2% in 2007. However, trends varied among Brazilian regions: there were significant increases in the North from 1999 to 2003 (2.7% per year), and in the South (1.0% per year) and Central-West regions (0.6% per year) from 1995 to 2007. For the entire period studied, higher LBW and lower IMRs were seen in more developed compared to less developed regions. In Brazilian States, in 2005, the higher the IMR rate, the lower the LBW rate (p=0.009); the lower the low schooling rate, the lower the LBW rate (p=0.007); the higher the number of neonatal intensive care beds per 1,000 live births, the higher the LBW rate (p=0.036). CONCLUSIONS: The low birth weight paradox was seen in Brazil. LBW rate is increasing in some Brazilian regions. Regional differences in LBW rate seem to be more associated to availability of perinatal care services than underlying social conditions.

Association between birth weight and neuromotor performance: a twin study

The development of neonatal intensive care has led to an increase in the prevalence of children with low birth weight and associated morbidity. The objectives of this study are to verify (1) The association between birth weight (BW) and neuromotor performance? (2) Is the neuromotor performance of twins within the normal range? (3) Are intra-pair similarities in neuromotor development of Monozygotic (MZ) and Disygotic (DZ) twins of unequal magnitude? The sample consisted of 191 children (78 MZ and 113 DZ), 8.9+3.1 years of age and with an average BW of 2246.3+485.4g. In addition to gestational characteristics, sports participation and Zurich Neuromotor Assessment (ZNA) were observed at childhood age. The statistical analysis was carried out with software SPSS 18.0, the STATA 10 and the ZNA performance scores. The level of significance was 0.05. For the neuromotor items high intra and inter-investigator reliabilities were obtained (0.793

Análise dos modos de falha e seus efeitos (FMEA) aplicada a um secador industrial

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

Maintenance and destrcution of R&D leadership

In the standard Schumpeterian-growth models only follower firms invest in R&D activities and larger economies grow faster. Since these results are counterfactual, this paper reveals that leader firms often support R&D activities and economic growth can be independent of the market size. In particular, the maintenance of R&D leadership increases with: (i) the technological-knowledge gap between leader and followers, since a firm-specific learning effect of accumulated technological knowledge from past R&D is considered, (ii) the leaders’ strategies that delay the next successful R&D supported by some follower firm, (iii) the market size, and (iv) the up-grade of each innovation.

Stochastic short-term maintenance scheduling of GENCOs in an oligopolistic electricity market

In the proposed model, the independent system operator (ISO) provides the opportunity for maintenance outage rescheduling of generating units before each short-term (ST) time interval. Long-term (LT) scheduling for 1 or 2 years in advance is essential for the ISO and the generation companies (GENCOs) to decide their LT strategies; however, it is not possible to be exactly followed and requires slight adjustments. The Cournot-Nash equilibrium is used to characterize the decision-making procedure of an individual GENCO for ST intervals considering the effective coordination with LT plans. Random inputs, such as parameters of the demand function of loads, hourly demand during the following ST time interval and the expected generation pattern of the rivals, are included as scenarios in the stochastic mixed integer program defined to model the payoff-maximizing objective of a GENCO. Scenario reduction algorithms are used to deal with the computational burden. Two reliability test systems were chosen to illustrate the effectiveness of the proposed model for the ST decision-making process for future planned outages from the point of view of a GENCO.

Is adolescent pregnancy a risk factor for low birth weight?

OBJECTIVE: The objective of this study was to evaluate whether adolescent pregnancy is a risk factor for low birth weight (LBW) babies. METHODS: This was a cross-sectional study of mothers and their newborns from a birth cohort in Aracaju, Northeastern Brazil. Data were collected consecutively from March to July 2005. Information collected included socioeconomic, biological and reproductive aspects of the mothers, using a standardized questionnaire. The impact of early pregnancy on birth weight was evaluated by multiple logistic regression. RESULTS: We studied 4,746 pairs of mothers and their babies. Of these, 20.6% were adolescents (< 20 years of age). Adolescent mothers had worse socioeconomic and reproductive conditions and perinatal outcomes when compared to other age groups. Having no prenatal care and smoking during pregnancy were the risk factors associated with low birth weight. Adolescent pregnancy, when linked to marital status "without partner", was associated with an increased proportion of low birth weight babies. CONCLUSIONS: Adolescence was a risk factor for LBW only for mothers without partners. Smoking during pregnancy and lack of prenatal care were considered to be independent risk factors for LBW.

Ecophysiology of Ruditapes decussatus

The physiological responses of the clam R. decussatus from the Ria Formosa, southern Portugal, were examined in relation to normoxia, hypoxia (11, 6, 3 and 1.2 kPa) and anoxia; acute elevation of temperature (at 20, 27 and 32 °C), and its effect on the resistance to air exposure (at 20, 28 and 35 °C); current velocity (0.6, 3, 8 17, 24 and 36 cm. s-1) and turbidity (10, 100 and 300 mg. l-1 dry weight of particulate matter), and the efficiency of this species in retaining particles of different size (at 10 and 100 mg. l-1); and to copper contamination considering both short-term acute exposure to high levels (0.1-10 mg Cu. l-1) and chronic environmental levels (0.01 mg Cu. l-1). Clearance rates, respiration rates, absorption efficiency and excretion rates were assessed through the physiological energetics in terms of the energy budget and scope for growth (SFG). Stress independent respiration rates (R) and clearance rates (CR) were observed in relation to hypoxia down to 12 kPa and 6 kPa, respectively. Anoxic rates were 3.6 % of normoxic rates. Scope for growth was greatly reduced under extreme hypoxia (14 % of SFG in normoxia). Respiration rate was temperature independent in the range 20-32 °C but the decline in clearance rate resulted in negative SFG at 32 °C. Gaping during air exposure and the maintenance of faster aerobic metabolism led to 100 % mortality in 20 hours at 35 °C, 4 days at 28 °C and 5 days at 20 °C. Low current velocities (≤ 8 cm. s-1) supported high clearance rates. Shear stresses ≥ 0.9 Pa induced sediment movement and disturbed the feeding processes resulting in decreased clearance rates (at 36 cm. s-1, is 10 % of maximum CR). The observed ability of jetting out depleted water at a different level than the one of the inhalant current results is an important adaptation of clams to the slow currents of sheltered environments. Ingestion at high seston concentrations (> 100 mg. l-1) is controled by reducing the amount filtered, lowering CR (to 30 % of CR at low seston loads) and producing pseudofeces. Observed efficient retention of particles (70-100 %) in the range 3 to 8 μm is beneficial when algal cells are diluted by fine silt particles as it is likely to occur in the clams natural environment. R. decussatus in the short term escaped the exposure to copper by valve closure and therefore acute tests are not applicable to adult clams of this species. At environmental levels chronic exposure to copper did not induce lethal effects during the exposure period (20 days), but scope for growth was reduced to c. 30 %, indicating sustained impairment of physiological functions. The sensitivity of the physiological energetics and the integrated scope for growth measurement in assessing stress effects caused by natural environmental factors was highlighted.

The importance of control monitoring systems in wind parks maintenance

The objective of every wind energy producer is to reduce operational costs associated to the production as a way to increase profits. One other issue that must be looked carefully is the equipment maintenance. Increase the availability of wind turbines by reducing the downtime associated to failures is a good strategy to achieve the main goal of increase profits. As a way to help in the definition of the best maintenance strategies, condition monitoring systems (CMS) have an important role to play. Informatics tools to make the condition monitoring of the wind turbines were developed and are now being installed as a way to help producers reducing the operational costs. There are a lot of developed systems to do the monitoring of a wind turbine or the whole wind park, in this paper will be made an overview of the most important systems.

A high level e-maintenance architecture to support on-site teams

Emergent architectures and paradigms targeting reconfigurable manufacturing systems increasingly rely on intelligent modules to maximize the robustness and responsiveness of modern installations. Although intelligent behaviour significantly minimizes the occurrence of faults and breakdowns it does not exclude them nor can prevent equipment’s normal wear. Adequate maintenance is fundamental to extend equipments’ life cycle. It is of major importance the ability of each intelligent device to take an active role in maintenance support. Further this paradigm shift towards “embedded intelligence”, supported by cross platform technologies, induces relevant organizational and functional changes on local maintenance teams. On the one hand, the possibility of outsourcing maintenance activities, with the warranty of a timely response, through the use of pervasive networking technologies and, on the other hand, the optimization of local maintenance staff are some examples of how IT is changing the scenario in maintenance. The concept of e-maintenance is, in this context, emerging as a new discipline with defined socio-economic challenges. This paper proposes a high level maintenance architecture supporting maintenance teams’ management and offering contextualized operational support. All the functionalities hosted by the architecture are offered to the remaining system as network services. Any intelligent module, implementing the services’ interface, can report diagnostic, prognostic and maintenance recommendations that enable the core of the platform to decide on the best course of action.

A survey of technologies and applications for climbing robots locomotion and adhesion

The interest in the development of climbing robots has grown rapidly in the last years. Climbing robots are useful devices that can be adopted in a variety of applications, such as maintenance and inspection in the process and construction industries. These systems are mainly adopted in places where direct access by a human operator is very expensive, because of the need for scaffolding, or very dangerous, due to the presence of an hostile environment. The main motivations are to increase the operation efficiency, by eliminating the costly assembly of scaffolding, or to protect human health and safety in hazardous tasks. Several climbing robots have already been developed, and other are under development, for applications ranging from cleaning to inspection of difficult to reach constructions. A wall climbing robot should not only be light, but also have large payload, so that it may reduce excessive adhesion forces and carry instrumentations during navigation. These machines should be capable of travelling over different types of surfaces, with different inclinations, such as floors, walls, or ceilings, and to walk between such surfaces (Elliot et al. (2006); Sattar et al. (2002)). Furthermore, they should be able of adapting and reconfiguring for various environment conditions and to be self-contained. Up to now, considerable research was devoted to these machines and various types of experimental models were already proposed (according to Chen et al. (2006), over 200 prototypes aimed at such applications had been developed in the world by the year 2006). However, we have to notice that the application of climbing robots is still limited. Apart from a couple successful industrialized products, most are only prototypes and few of them can be found in common use due to unsatisfactory performance in on-site tests (regarding aspects such as their speed, cost and reliability). Chen et al. (2006) present the main design problems affecting the system performance of climbing robots and also suggest solutions to these problems. The major two issues in the design of wall climbing robots are their locomotion and adhesion methods. With respect to the locomotion type, four types are often considered: the crawler, the wheeled, the legged and the propulsion robots. Although the crawler type is able to move relatively faster, it is not adequate to be applied in rough environments. On the other hand, the legged type easily copes with obstacles found in the environment, whereas generally its speed is lower and requires complex control systems. Regarding the adhesion to the surface, the robots should be able to produce a secure gripping force using a light-weight mechanism. The adhesion method is generally classified into four groups: suction force, magnetic, gripping to the surface and thrust force type. Nevertheless, recently new methods for assuring the adhesion, based in biological findings, were proposed. The vacuum type principle is light and easy to control though it presents the problem of supplying compressed air. An alternative, with costs in terms of weight, is the adoption of a vacuum pump. The magnetic type principle implies heavy actuators and is used only for ferromagnetic surfaces. The thrust force type robots make use of the forces developed by thrusters to adhere to the surfaces, but are used in very restricted and specific applications. Bearing these facts in mind, this chapter presents a survey of different applications and technologies adopted for the implementation of climbing robots locomotion and adhesion to surfaces, focusing on the new technologies that are recently being developed to fulfill these objectives. The chapter is organized as follows. Section two presents several applications of climbing robots. Sections three and four present the main locomotion principles, and the main "conventional" technologies for adhering to surfaces, respectively. Section five describes recent biological inspired technologies for robot adhesion to surfaces. Section six introduces several new architectures for climbing robots. Finally, section seven outlines the main conclusions.

Diabetes burden in Brazil: fraction attributable to overweight, obesity, and excess weight

OBJECTIVE To estimate the burden of type 2 diabetes mellitus and its percentage attributable to overweight and obesity in Brazil.METHODS The burden of diabetes mellitus was described in terms of disability-adjusted life years, which is the sum of two components: years of life lost and years lived with disability. To calculate the fraction of diabetes mellitus attributable to overweight, obesity, and excess weight, we used the prevalence of these risk factors according to sex and age groups (> 20 years) obtained from the 2008 Pesquisa Dimensões Sociais das Desigualdades (Social Dimensions of Inequality Survey) and the relative risks derived from the international literature.RESULTS Diabetes mellitus accounted for 5.4% of Brazilian disability-adjusted life years in 2008, with the largest fraction attributed to the morbidity component (years lived with disability). Women exhibited higher values for disability-adjusted life years. In Brazil, 49.2%, 58.3%, and 70.6% of diabetes mellitus in women was attributable to overweight, obesity, and excess weight, respectively. Among men, these percentages were 40.5%, 45.4%, and 60.3%, respectively. Differences were observed with respect to Brazilian regions and age groups.CONCLUSIONS A large fraction of diabetes mellitus was attributable to preventable individual risk factors and, in about six years, the contribution of these factors significant increased, particularly among men. Policies aimed at promoting healthy lifestyle habits, such as a balanced diet and physical activity, can have a significant impact on reducing the burden of diabetes mellitus in Brazil.

Dietary patterns in pregnancy and birth weight

OBJECTIVE To analyze if dietary patterns during the third gestational trimester are associated with birth weight.METHODS Longitudinal study conducted in the cities of Petropolis and Queimados, Rio de Janeiro (RJ), Southeastern Brazil, between 2007 and 2008. We analyzed data from the first and second follow-up wave of a prospective cohort. Food consumption of 1,298 pregnant women was assessed using a semi-quantitative questionnaire about food frequency. Dietary patterns were obtained by exploratory factor analysis, using the Varimax rotation method. We also applied the multivariate linear regression model to estimate the association between food consumption patterns and birth weight.RESULTS Four patterns of consumption – which explain 36.4% of the variability – were identified and divided as follows: (1) prudent pattern (milk, yogurt, cheese, fruit and fresh-fruit juice, cracker, and chicken/beef/fish/liver), which explained 14.9% of the consumption; (2) traditional pattern, consisting of beans, rice, vegetables, breads, butter/margarine and sugar, which explained 8.8% of the variation in consumption; (3) Western pattern (potato/cassava/yams, macaroni, flour/farofa/grits, pizza/hamburger/deep fried pastries, soft drinks/cool drinks and pork/sausages/egg), which accounts for 6.9% of the variance; and (4) snack pattern (sandwich cookie, salty snacks, chocolate, and chocolate drink mix), which explains 5.7% of the consumption variability. The snack dietary pattern was positively associated with birth weight (β = 56.64; p = 0.04) in pregnant adolescents.CONCLUSIONS For pregnant adolescents, the greater the adherence to snack pattern during pregnancy, the greater the baby’s birth weight.

Body weight gain during adulthood and uterine myomas: Pró-Saúde Study

This study intended to investigate whether body weight gain during adulthood is associated with uterine myomas. 1,560 subjects were evaluated in a Pró-Saúde Study. Weight gain was evaluated in a continuous fashion and also in quintiles. Odds ratios and 95% confidence intervals were estimated through logistic regression models that were adjusted for education levels, color/race, body mass indices at age 20, age of menarche, parity, use of oral contraceptive methods, smoking, health insurance, and the Papanicolaou tests. No relevant differences were observed regarding the presence of uterine myomas among weight gain quintiles in that studied population.

Influence of constraining and confinement in the molecular mobility of low molecular weight materials

Dissertation presented to obtain a Ph.D. Degree in Chemical Physics