Integration of knowledge-based, qualitative and numeric tools for real time dynamic systems supervision

The proposal presented in this thesis is to provide designers of knowledge based supervisory systems of dynamic systems with a framework to facilitate their tasks avoiding interface problems among tools, data flow and management. The approach is thought to be useful to both control and process engineers in assisting their tasks. The use of AI technologies to diagnose and perform control loops and, of course, assist process supervisory tasks such as fault detection and diagnose, are in the scope of this work. Special effort has been put in integration of tools for assisting expert supervisory systems design. With this aim the experience of Computer Aided Control Systems Design (CACSD) frameworks have been analysed and used to design a Computer Aided Supervisory Systems (CASSD) framework. In this sense, some basic facilities are required to be available in this proposed framework: ·

Diseño de un sistema inalámbrico para la recogida de diferentes parámetros en el ámbito de la práctica deportiva del surf

[ES]En este documento se presenta el Trabajo Fin de Grado llevado a cabo con el objetivo de realizar el diseño de un sistema inalámbrico para la recogida de parámetros en el ámbito de la práctica deportiva del surf. Para alcanzar los objetivos de este trabajo, se ha analizado el estado del arte asociado a dicho sistema, con el fin de distinguir el comportamiento de los sensores y tecnologías inalámbricas. Por último, mediante la metodología llevada a cabo se ha realizado el diseño general del sistema, así como, el diseño de un sistema reducido.

Model-based vehicle detection and classification using orthographic approximations

This paper reports the current state of work to simplify our previous model-based methods for visual tracking of vehicles for use in a real-time system intended to provide continuous monitoring and classification of traffic from a fixed camera on a busy multi-lane motorway. The main constraints of the system design were: (i) all low level processing to be carried out by low-cost auxiliary hardware, (ii) all 3-D reasoning to be carried out automatically off-line, at set-up time. The system developed uses three main stages: (i) pose and model hypothesis using 1-D templates, (ii) hypothesis tracking, and (iii) hypothesis verification, using 2-D templates. Stages (i) & (iii) have radically different computing performance and computational costs, and need to be carefully balanced for efficiency. Together, they provide an effective way to locate, track and classify vehicles.

Solving complex optimal control problems at no cost with PSOPT

This paper introduces PSOPT, an open source optimal control solver written in C++. PSOPT uses pseudospectral and local discretizations, sparse nonlinear programming, automatic differentiation, and it incorporates automatic scaling and mesh refinement facilities. The software is able to solve complex optimal control problems including multiple phases, delayed differential equations, nonlinear path constraints, interior point constraints, integral constraints, and free initial and/or final times. The software does not require any non-free platform to run, not even the operating system, as it is able to run under Linux. Additionally, the software generates plots as well as LATEX code so that its results can easily be included in publications. An illustrative example is provided.

Improving mW/MHz ratio in FPGAs pipelined designs

This paper presents a simple clocking technique to migrate classical synchronous pipelined designs to a synchronous functional-equivalent alternative system in the context of FPGAs. When the new pipelined design runs at the same throughput of the original design, around 30% better mW/MHz ratio was observed in Virtex-based FPGA circuits. The evaluation is done using a simple but representative and practical systolic design as an example. The technique in essence is a simple replacement of the clocking mechanism for the pipe-storage elements; however no extra design effort is needed. The results show that the proposed technique allows immediate power and area-time savings of existing designs rather than exploring potential benefits by a new logic design to the problem using the classic pipeline clocking mechanism.

Head-controlled assistive telerobot with extended physiological proprioception capability

People with disabilities such as quadriplegia can use mouth-sticks and head-sticks as extension devices to perform desired manipulations. These extensions provide extended proprioception which allows users to directly feel forces and other perceptual cues such as texture present at the tip of the mouth-stick. Such devices are effective for two principle reasons: because of their close contact with the user's tactile and proprioceptive sensing abilities; and because they tend to be lightweight and very stiff, and can thus convey tactile and kinesthetic information with high-bandwidth. Unfortunately, traditional mouth-sticks and head-sticks are limited in workspace and in the mechanical power that can be transferred because of user mobility and strength limitations. We describe an alternative implementation of the head-stick device using the idea of a virtual head-stick: a head-controlled bilateral force-reflecting telerobot. In this system the end-effector of the slave robot moves as if it were at the tip of an imaginary extension of the user's head. The design goal is for the system is to have the same intuitive operation and extended proprioception as a regular mouth-stick effector but with augmentation of workspace volume and mechanical power. The input is through a specially modified six DOF master robot (a PerForceTM hand-controller) whose joints can be back-driven to apply forces at the user's head. The manipulation tasks in the environment are performed by a six degree-of-freedom slave robot (the Zebra-ZEROTM) with a built-in force sensor. We describe the prototype hardware/software implementation of the system, control system design, safety/disability issues, and initial evaluation tasks.

Investigation of the accuracy of historical irradiance products and interannual variability of solar irradiance using Met Office ground data

Met Office station data from 1980 to 2012 has been used to characterise the interannual variability of incident solar irradiance across the UK. The same data are used to evaluate four popular historical irradiance products to determine which are most suitable for use by the UK PV industry for site selection and system design. The study confirmed previous findings that interannual variability is typically 3–6% and weighted average probability of a particular percentage deviation from the mean at an average site in the UK was calculated. This weighted average showed that fewer than 2% of site-years could be expected to fall below 90% of the long-term site mean. The historical irradiance products were compared against Met Office station data from the input years of each product. This investigation has found that all products perform well. No products have a strong spatial trend. Meteonorm 7 is most conservative (MBE = −2.5%), CMSAF is most optimistic (MBE = +3.4%) and an average of all four products performs better than any one individual product (MBE = 0.3%)

Aspects of designing and evaluating seasonal-to-interannual Arctic sea-ice prediction systems

Using lessons from idealised predictability experiments, we discuss some issues and perspectives on the design of operational seasonal to inter-annual Arctic sea-ice prediction systems. We first review the opportunities to use a hierarchy of different types of experiment to learn about the predictability of Arctic climate. We also examine key issues for ensemble system design, such as: measuring skill, the role of ensemble size and generation of ensemble members. When assessing the potential skill of a set of prediction experiments, using more than one metric is essential as different choices can significantly alter conclusions about the presence or lack of skill. We find that increasing both the number of hindcasts and ensemble size is important for reliably assessing the correlation and expected error in forecasts. For other metrics, such as dispersion, increasing ensemble size is most important. Probabilistic measures of skill can also provide useful information about the reliability of forecasts. In addition, various methods for generating the different ensemble members are tested. The range of techniques can produce surprisingly different ensemble spread characteristics. The lessons learnt should help inform the design of future operational prediction systems.

Structural Characterization of Photopolymerizable Binary Liposomes Containing Diacetylenic and Saturated Phospholipids

The use of liposomes to encapsulate materials has received widespread attention for drug delivery, transfection, diagnostic reagent, and as immunoadjuvants. Phospholipid polymers form a new class of biomaterials with many potential applications in medicine and research. Of interest are polymeric phospholipids containing a diacetylene moiety along their acyl chain since these kinds of lipids can be polymerized by Ultra-Violet (UV) irradiation to form chains of covalently linked lipids in the bilayer. In particular the diacetylenic phosphatidylcholine 1,2-bis(10,12-tricosadiynoyl)- sn-glycero-3-phosphocholine (DC8,9PC) can form intermolecular cross-linking through the diacetylenic group to produce a conjugated polymer within the hydrocarbon region of the bilayer. As knowledge of liposome structures is certainly fundamental for system design improvement for new and better applications, this work focuses on the structural properties of polymerized DC8,9PC:1,2-dimyristoyl-sn-glycero-3-phusphocholine (DMPC) liposomes. Liposomes containing mixtures of DC8,9PC and DMPC, at different molar ratios, and exposed to different polymerization cycles, were studied through the analysis of the electron spin resonance (ESR) spectra of a spin label incorporated into the bilayer, and the calorimetric data obtained from differential scanning calorimetry (DSC) studies. Upon irradiation, if all lipids had been polymerized, no gel-fluid transition would be expected. However, even samples that went through 20 cycles of UV irradiation presented a DSC band, showing that around 80% of the DC8,9PC molecules were not polymerized. Both DSC and ESR indicated that the two different lipids scarcely mix at low temperatures, however few molecules of DMPC are present in DC8,9PC rich domains and vice versa. UV irradiation was found to affect the gel fluid transition of both DMPC and DC8,9PC rich regions, indicating the presence of polymeric units of DC8,9PC in both areas, A model explaining lipids rearrangement is proposed for this partially polymerized system.

Emissions from realistic operation of residential wood pellets heating systems

Emissions from residential combustion appliances vary significantly depending on the firing behaviours and combustion conditions, in addition to combustion technologies and fuel quality. Although wood pellet combustion in residential heating boilers is efficient, the combustion conditions during start-up and stop phases are not optimal and produce significantly high emissions such as carbon monoxide and hydrocarbon from incomplete combustion. The emissions from the start-up and stop phases of the pellet boilers are not fully taken into account in test methods for ecolabels which primarily focus on emissions during operation on full load and part load. The objective of the thesis is to investigate the emission characteristics during realistic operation of residential wood pellet boilers in order to identify when the major part of the annual emissions occur. Emissions from four residential wood pellet boilers were measured and characterized for three operating phases (start-up, steady and stop). Emissions from realistic operation of combined solar and wood pellet heating systems was continuously measured to investigate the influence of start-up and stop phases on total annual emissions. Measured emission data from the pellet devices were used to build an emission model to predict the annual emission factors from the dynamic operation of the heating system using the simulation software TRNSYS. Start-up emissions are found to vary with ignition type, supply of air and fuel, and time to complete the phase. Stop emissions are influenced by fan operation characteristics and the cleaning routine. Start-up and stop phases under realistic operation conditions contribute 80 – 95% of annual carbon monoxide (CO) emission, 60 – 90% total hydrocarbon (TOC), 10 – 20% of nitrogen oxides (NO), and 30 – 40% particles emissions. Annual emission factors from realistic operation of tested residential heating system with a top fed wood pelt boiler can be between 190 and 400 mg/MJ for the CO emissions, between 60 and 95 mg/MJ for the NO, between 6 and 25 mg/MJ for the TOC, between 30 and 116 mg/MJ for the particulate matter and between 2x10-13 /MJ and 4x10-13 /MJ for the number of particles. If the boiler has the cleaning sequence with compressed air such as in boiler B2, annual CO emission factor can be up to 550 mg/MJ. Average CO, TOC and particles emissions under realistic annual condition were greater than the limits values of two eco labels. These results highlight the importance of start-up and stop phases in annual emission factors (especially CO and TOC). Since a large or dominating part of the annual emissions in real operation arise from the start-up and stop sequences, test methods required by the ecolabels should take these emissions into account. In this way it will encourage the boiler manufacturers to minimize annual emissions. The annual emissions of residential pellet heating system can be reduced by optimizing the number of start-ups of the pellet boiler. It is possible to reduce up to 85% of the number of start-ups by optimizing the system design and its controller such as switching of the boiler pump after it stops, using two temperature sensors for boiler ON/OFF control, optimizing of the positions of the connections to the storage tank, increasing the mixing valve temperature in the boiler circuit and decreasing the pump flow rate. For 85 % reduction of start-ups, 75 % of CO and TOC emission factors were reduced while 13% increase in NO and 15 % increase in particle emissions was observed.

Prototype Generation from Ontology Charts

Semantic Analysis is a business analysis method designed to capture system requirements. While these requirements may be represented as text, the method also advocates the use of Ontology Charts to formally denote the system's required roles, relationships and forms of communication. Following model driven engineering techniques, Ontology Charts can be transformed to temporal Database schemas, class diagrams and component diagrams, which can then be used to produce software systems. A nice property of these transformations is that resulting system design models lend themselves to complicated extensions that do not require changes to the design models. For example, resulting databases can be extended with new types of data without the need to modify the database schema of the legacy system. Semantic Analysis is not widely used in software engineering, so there is a lack of experts in the field and no design patterns are available. This make it difficult for the analysts to pass organizational knowledge to the engineers. This study describes an implementation that is readily usable by engineers, which includes an automated technique that can produce a prototype from an Ontology Chart. The use of such tools should enable developers to make use of Semantic Analysis with minimal expertise of ontologies and MDA.

Determinação da dose eritematosa mínima como marcador de risco e sensibilidade à radiação ultravioleta

Objetivos: Determinar a dose eritematosa mínima (DEM) medida por exposição controlada à radiação ultravioleta-B (RUV-B), como limiar para dano solar agudo nos diversos fototipos, e medir a cor da pele constitucional pelo sistema colorimétrico CIELAB. Pacientes e Métodos: Um total de 194 voluntários, sadios, com idades acima de 18 anos, distribuídos em um mínimo de 30 participantes por fototipo. Todos foram classificados por fototipos segundo os critérios de Fitzpatrick. As regiões infra-axilar torácica e nádega foram irradiadas em 4 áreas de 1 cm2, assim como foi registrada a cor da pele desses locais pelo sistema CIELAB. Delineamento: Estudo transversal. Resultados: A média de idade dos participantes foi de 38 anos, sendo 68% do sexo feminino. A avaliação da associação entre as medidas das DEMs e dos valores colorimétricos da coordenada L*, mostrou uma correlação de Pearson negativa com r = -0,91 para um valor p<0,05. Para os valores das DEMs e os escores da classificação dos voluntários por fototipos, obteve-se correlação de Spearman (rs) de +0,95 para p<0,05 e, correlacionando os valores colorimétricos com os escores dos fototipos, encontrou-se em tórax um rs de -0,93 e em nádega -0,92 para um p < 0,05. Conclusões – Concluiu-se que: 1)- a mensuração dos valores colorimétricos da coordenada L* nas regiões infra-axilar torácica e nádega mostraram uma forte correlação com os valores das DEMs, sendo de menor poder invasivo e de maior praticidade para mensuração de sensibilidade à radiação ultravioleta; 2)- apesar de os escores de Fitzpatrick terem alta correlação com os valores das DEMs, mostraram superposição de valores nos fototipos adjacentes; 3)- o grau de associação das classes dos fototipos com a cor da pele permite dizer que a categoria numérica do fototipo aumenta à medida que a pele fica mais escura.