Impact of different irrigation strategies on grapes and wine quality of four grapevine cultivars (Vitis sp.) in cool climate conditions. An investigation into the relationships among ABA, water status, grape cultivar and wine quality

Niagara Peninsula of Ontario is the largest viticultural area in Canada. Although it is considered to be a cool and wet region, in the last decade many water stress events occurred during the growing seasons with negative effects on grape and wine quality. This study was initiated to understand and develop the best strategies for water management in vineyards and those that might contribute to grape maturity advancement. The irrigation trials investigated the impact of time of initiation (fruit set, lag phase and veraison), water replacement level based on theoretical loss through crop evapotranspiration (ETc; 100,50 and 25%) and different irrigation strategies [partial root zone drying (PRD) versus regulated deficit irrigation (RD!)] on grape composition and wine sensory profiles. The irrigation experiments were conducted in a commercial vineyard (Lambert Vineyards Inc.) located in Niagara-on-the-Lake, Ontario, from 2005 through 2009. The two experiments that tested the combination of different water regimes and irrigation time initiation were set up in a randomized block design as follows: Baco noir - three replicates x 10 treatments [(25%, 50% and 100% of ETc) x (initiation at fruit set, lag phase and veraison) + control]; Chardonnay - three replicates x seven treatments [(25%, 50% and 100% of ETc) x (initiation at fruit set and veraison) + control]. The experiments that tested different irrigation strategies were set up on two cultivars as follows: Sauvignon blanc - four replicates x four treatments [control, fully irrigated (100% ETc), PRD (100% ETc) and RDI (25% ETc)]; Cabemet Sauvignon - four replicates x five treatments [control, fully irrigated (100% ETc), PRD (100% ETc), RDI (50% ETc) and RDI (25% ETc)]. The controls in each experiment were nonirrigated. The irrigation treatments were compared for many variables related to soil water status, vine physiology, berry composition, wine sensory profile, and hormone composition [(abscisic acid (ABA) and its catabolites]. Soil moisture profile was mostly affected by irrigation treatments between 20 and 60 em depth depending on the grapevine cultivar and the regime of water applied. Overall soil moisture was consistently higher throughout the season in 100 and 50% ETc compare to the control. Transpiration rates and leaf temperature as well as shoot growth rate were the most sensitive variables to soil water status. Drip irrigation associated with RDI treatments (50% ETc and 25% ETc) had the most beneficial effects on vine physiology, fruit composition and wine varietal typicity, mainly by maintaining a balance between vegetative and reproductive parts of the vine. Neither the control nor the 100 ETc had overall a positive effect on grape composition and wine sensory typicity. The time of irrigation initiation affected the vine physiology and grape quality, the most positive effect was found in treatments initiated at lag phase and veraison. RDI treatments were overall more consistent in their positive effect on grape composition and wine varietal typicity comparing to PRD treatment. The greatest difference between non-irrigated and irrigated vines in most of the variables studied was found in 2007, the driest and hottest season of the experimental period. Soil water status had a greater and more consistent effect on red grapevine cultivars rather than on white winegrape cultivars. To understand the relationships among soil and plant water status, plant physiology and the hormonal profiles associated with it, abscisic acid (ABA) and its catabolites [phaseic acid (PA), dihydrophaseic acid (DPA), 7-hydroxy-ABA (TOH-ABA), 8' -hydroxy-ABA, neophaseic acid and abscisic acid glucose ester (ABA-GE)] were analyzed in leaves and berries from the Baco noir and Chardonnay irrigation trials over two growing seasons. ABA and some of its catabolites accurately described the water status in the vines. Endogenous ABA and some of its catabolites were strongly affected in Baco noir and Chardonnay by both the water regime (i.e. ET level) and timing of irrigation initiation. Chardonnay grapevines produced less ABA in both leaves and berries compared to Baco noir, which indicated that ABA synthesis is also cultivar dependant. ABA-GE was the main catabolite in treatments with high water deficits, while PA and DPA were higher in treatments with high water status, suggesting that the vine produced more ABA-GE under water deficits to maintain rapid control of the stomata. These differences between irrigation treatments with respect to ABA and catabolites were particularly noticeable in the dry 2007 season. Two trials using exogenous ABA investigated the effect of different concentrations of ABA and organs targeted for spraying, on grape maturation and berry composition of Cabemet Sauvignon grapevines, in two cool and wet seasons (2008-2009). The fIrst experiment consisted of three replicates x three treatments [(150 and 300 mg/L, both applications only on clusters) + untreated control] while the second experiment consisted in three replicates x four treatments [(full canopy, only clusters, and only leaves sprayed with 300 ppm ABA) + untreated control]. Exogenous ABA was effective in hastening veraison, and improving the composition of Cabemet Sauvignon. Ability of ABA to control the timing of grape berry maturation was dependant on both solution concentration and the target organ. ABA affected not only fruit composition but also yield components. Berries treated with ABA had lower weight and higher skin dry mass, which constitutes qualitative aspects desired in the wine grapes. Temporal advancement of ripening through hormonal control can lead to earlier fruit maturation, which is a distinct advantage in cooler areas or areas with a high risk of early frost occurrence. Exogenous ABA could provide considerable benefits to wine industry in terms of grape composition, wine style and schedule activities in the winery, particularly in wet and cool years. These trials provide the ftrst comprehensive data in eastern North America on the response of important hybrid and Vitis vinifera winegrape cultivars to irrigation management. Results from this study additionally might be a forward step in understanding the ABA metabolism, and its relationship with water status. Future research should be focused on ftnding the ABA threshold required to trigger the ripening process, and how this process could be controlled in cool climates.

Lighting recommendations for the Ryan Electric Scintillator and Fireworks Program for the official dedication Niagara Falls illumination, 1925

Walter D’Arcy Ryan was born in 1870 in Kentville, Nova Scotia. He became the chief of the department of illumination at the General Electric Company of Schenectady, New York. He was a founder in the field of electrical illumination. He built the electric steam scintillator which had numerous nozzles and valves. The operator would release steam through the valves. The nozzles all had names which included: Niagara, fan, snake, plume, column, pinwheel and sunburst. The steam scintillator was combined with projectors, prismatic reflectors, flashers and filters to produce the desired effects. In 1920 a group of businessmen from Niagara Falls, New York formed a group who called themselves the “generators’. They lobbied the American and Canadian governments to improve the illumination of the Falls. They were able to raise $58, 000 for the purchase and installation of 24 arc lights to illuminate the Falls. On February 24th, 1925 the Niagara Falls Illumination Board was formed. Initially, the board had a budget of $28,000 for management, operation and maintenance of the lights. The power was supplied free by the Ontario Power Company. They had 24 lights installed in a row on the Ontario Power Company surge tank which was next to the Refectory in Victoria Park on the Canadian side. The official opening ceremony took place on June 8th, 1925 and included a light parade in Niagara Falls, New York and an international ceremony held in the middle of the Upper Steel Arch Bridge. Walter D’Arcy Ryan was the illuminating engineer and A.D. Dickerson who was his New York field assistant directed the scintillator. with information from American Technological Sublime by David E. Nye and the Niagara Falls info website Location: Brock University Archives Source Information: Subject Headings: Added Entries: 100 Ryan, W. D’A. |q (Walter D’Arcy), |d 1870-1934 610 General Electric Company 650 Lighting, Architectural and decorative 650 Lighting |z New York (State) |z Niagara Falls 700 Dickerson, A.F. 700 Schaffer, J.W. Related material held at other repositories: The Niagara Falls Museum in Niagara Falls, Ontario has a program (pamphlet) dedicating new lighting in 1958 and it has postcards depicting the illumination of the Falls. Some of Ryan’s accomplishments can be seen at The Virtual Museum of the City of San Francisco. Described by: Anne Adams Date: Sept 26,Upper Steel Arch Bridge. Walter D’Arcy Ryan was the illuminating engineer and A.D. Dickerson who was his New York field assistant directed the scintillator. with information from American Technological Sublime by David E. Nye and the Niagara Falls info website

Étude de la cinétique de biomarqueurs d’exposition à la perméthrine dans des conditions d’exposition réelles chez les travailleurs agricoles au Québec

La perméthrine fait partie de la famille des pyréthrinoïdes qui sont abondamment utilisés en agriculture. Le but de cette étude était d'obtenir des données sur la cinétique des biomarqueurs d'exposition à la perméthrine en condition réelle d'exposition chez les travailleurs agricoles. Douze travailleurs (un applicateur, un superviseur et dix cueilleurs) exposés à la perméthrine dans le cadre de leur emploi ont été recrutés dans une ferme maraichère de la Montérégie (Québec). Ils ont fourni toutes leurs urines sur une période de trois jours suivant le début des travaux dans un champ traité. Les trois principaux métabolites de la perméthrine, l'acide cis-/trans-3-(2,2-dichlorovinyle)-2,2-diméthylecyclopropane carboxylique (cis-/trans-DCCA) et l'acide 3-phénoxybenzoïque (3-PBA) ont été analysés par chromatographie liquide à ultra-haute performance couplée à la spectrométrie de masse à temps de vol. Pour l'applicateur, une augmentation progressive des valeurs d'excrétion a été observée avec un pic unique atteint environ 30 h après le début de l'exposition d'une durée de 3,5 h suivi d'une élimination avec une demi-vie de 8 h. Pour le superviseur et l'un des cueilleurs, les profils d'excrétion de trans-DCCA et de 3-PBA étaient compatibles avec de multiples entrées dans la zone traitée pendant la période d'échantillonnage accompagné d'une élimination rapide entre les épisodes d'exposition.L'applicateur aurait été exposé indirectement par contact main-bouche, alors que les autres travailleurs auraient été exposés par la voie cutanée. Pour une surveillance biologique adéquate, nous recommandons de mesurer deux biomarqueurs de la perméthrine, soit le trans-DCCA et le 3-PBA et de prendre un minimum de trois échantillons urinaires, un avant et deux pendant ou suivant la période d'exposition.

Lutte intégrée au roseau commun : prévention, confinement et éradication

Les plantes envahissantes menacent la biodiversité ainsi que les activités humaines. Afin de les maîtriser, la pulvérisation d'herbicides est une méthode fréquemment employée en Amérique du Nord. Cette approche ne fait pas toujours consensus et est même parfois interdite ou restreinte, ce qui justifie le recours à d'autres options. Les alternatives peuvent toutefois s'avérer rares, comporter d'importantes limitations ou sont peu documentées. Cette étude vise à tester l’efficacité de méthodes permettant de maîtriser et de prévenir les invasions de roseau commun (Phragmites australis), l'une des plantes envahissantes les plus problématiques sur le continent nord-américain, tout en limitant au minimum l'utilisation d'herbicides. Le potentiel de quatre méthodes de lutte aux petites populations de roseau bien établies a d'abord été évalué : l’excavation avec enfouissement sur place, le bâchage, l’excavation avec enfouissement sur place combinée au bâchage, et la fauche répétée. Les résultats ont montré que l'excavation avec enfouissement sur place, avec ou sans bâchage, a entraîné une élimination presque totale des populations visées, ce qui est comparable ou supérieur à l'effet généralement obtenu avec la pulvérisation d'herbicide. Le bâchage avec des toiles opaques, maintenues pendant un an, a pour sa part entraîné une maîtrise partielle du roseau, suggérant qu'une application prolongée serait nécessaire pour l'éradication de la plante. La fauche répétée, exécutée à raison de cinq fauches par été pendant deux ans, a fourni une efficacité mitigée. Les résultats suggèrent néanmoins que la fauche pendant plusieurs années contribue à affaiblir la plante, ce qui pourrait aider à son confinement. Une méthode additionnelle a été expérimentée afin de traiter les tiges éparses de roseau tout en limitant les risques d'effets hors cibles, soit le badigeonnage manuel d’herbicide. Suite à ces tests, les résultats ont montré une diminution importante de la densité des tiges, ce qui suggère que la méthode est efficace afin d'éliminer les repousses après un traitement initial, et pourrait également être employée sur de jeunes populations clairsemées. L'effet d'un ensemencement préventif de plantes herbacées sur l'établissement de semis de roseau a également été étudié, suite à des traitements sur de vastes parcelles de sol nu. Les résultats suggèrent que la méthode est efficace afin de limiter la propagation du roseau par semences et qu'un suivi périodique suite à l'intervention serait suffisant afin de maintenir l'effet préventif.

Spray Pyrolysed Zinc Oxide Thin Films : Effects of Doping and Ion Beam Irradiation

In recent years scientists have made rapid and significant advances in the field of semiconductor physics. One of the most important fields of current interest in materials science is the fundamental aspects and applications of conducting transparent oxide thin films (TCO). The characteristic properties of such coatings are low electrical resistivity and high transparency in the visible region. The first semitransparent and electrically conducting CdO film was reported as early as in 1907 [1]. Though early work on these films was performed out of purely scientific interest, substantial technological advances in such films were made after 1940. The technological interest in the study of transparent semiconducting films was generated mainly due to the potential applications of these materials both in industry and research. Such films demonstrated their utility as transparent electrical heaters for windscreens in the aircraft industry. However, during the last decade, these conducting transparent films have been widely used in a variety of other applications such as gas sensors [2], solar cells [3], heat reflectors [4], light emitting devices [5] and laser damage resistant coatings in high power laser technology [6]. Just a few materials dominate the current TCO industry and the two dominant markets for TCO’s are in architectural applications and flat panel displays. The architectural use of TCO is for energy efficient windows. Fluorine doped tin oxide (FTO), deposited using a pyrolysis process is the TCO usually finds maximum application. SnO2 also finds application ad coatings for windows, which are efficient in preventing radiative heat loss, due to low emissivity (0.16). Pyrolitic tin oxide is used in PV modules, touch screens and plasma displays. However indium tin oxide (ITO) is mostly used in the majority of flat panel display (FPD) applications. In FPDs, the basic function of ITO is as transparent electrodes. The volume of FPD’s produced, and hence the volume of ITO coatings produced, continues to grow rapidly. But the current increase in the cost of indium and the scarcity of this material created the difficulty in obtaining low cost TCOs. Hence search for alternative TCO materials has been a topic of active research for the last few decades. This resulted in the development of binary materials like ZnO, SnO2, CdO and ternary materials like II Zn2SnO4, CdSb2O6:Y, ZnSO3, GaInO3 etc. The use of multicomponent oxide materials makes it possible to have TCO films suitable for specialized applications because by altering their chemical compositions, one can control the electrical, optical, chemical and physical properties. But the advantages of using binary materials are the easiness to control the chemical compositions and depositions conditions. Recently, there were reports claiming the deposition of CdO:In films with a resistivity of the order of 10-5 ohm cm for flat panel displays and solar cells. However they find limited use because of Cd-Toxicity. In this regard, ZnO films developed in 1980s, are very useful as these use Zn, an abundant, inexpensive and nontoxic material. Resistivity of this material is still not very low, but can be reduced through doping with group-III elements like In, Al or Ga or with F [6]. Hence there is a great interest in ZnO as an alternative of ITO. In the present study, we prepared and characterized transparent and conducting ZnO thin films, using a cost effective technique viz Chemical Spray Pyrolysis (CSP). This technique is also suitable for large area film deposition. It involves spraying a solution, (usually aqueous) containing soluble salts of the constituents of the desired compound, onto a heated substrate.

Engineering the Properties of Indium Sulfide for Thin Film Solar Cells by Doping

In the present work, structural, optical and electrical properties of indium sulfide are tuned by specific and controlled doping. Silver, tin, copper and chlorine were used as the doping elements. In2S3 thin films for the present study were prepared using a simple and low cost “Chemical Spray Pyrolysis (CSP)” technique. This technique is adaptable for large-area deposition of thin films in any required shape and facilitates easiness of doping and/or variation of atomic ratio. It involves spraying a solution, usually aqueous, containing soluble salts of the constituents of the desired compound onto a heated substrate. Doping process was optimized for different doping concentrations. On optimizing doping conditions, we tuned the structural, optical and electrical properties of indium sulfide thin films making them perform as an ideal buffer layer.

Automation of Chemical Spray Pyrolysis Unit and Fabrication of Sprayed CuInS2/In2S3 Solar Cell

Aim of the present work was to automate CSP process, to deposit and characterize CuInS2/In2S3 layers using this system and to fabricate devices using these films.An automated spray system for the deposition of compound semiconductor thin films was designed and developed so as to eliminate the manual labour involved in spraying and facilitate standardization of the method. The system was designed such that parameters like spray rate, movement of spray head, duration of spray, temperature of substrate, pressure of carrier gas and height of the spray head from the substrate could be varied. Using this system, binary, ternary as well as quaternary films could be successfully deposited.The second part of the work deal with deposition and characterization of CuInS2 and In2S3 layers respectively.In the case of CuInS2 absorbers, the effects of different preparation conditions and post deposition treatments on the optoelectronic, morphological and structural properties were investigated. It was observed that preparation conditions and post deposition treatments played crucial role in controlling the properties of the films. The studies in this direction were useful in understanding how the variation in spray parameters tailored the properties of the absorber layer. These results were subsequently made use of in device fabrication process.Effects of copper incorporation in In2S3 films were investigated to find how the diffusion of Cu from CuInS2 to In2S3 will affect the properties at the junction. It was noticed that there was a regular variation in the opto-electronic properties with increase in copper concentration.Devices were fabricated on ITO coated glass using CuInS2 as absorber and In2S3 as buffer layer with silver as the top electrode. Stable devices could be deposited over an area of 0.25 cm2, even though the efficiency obtained was not high. Using manual spray system, we could achieve devices of area 0.01 cm2 only. Thus automation helped in obtaining repeatable results over larger areas than those obtained while using the manual unit. Silver diffusion on the cells before coating the electrodes resulted in better collection of carriers.From this work it was seen CuInS2/In2S3 junction deposited through automated spray process has potential to achieve high efficiencies.

Development of a Technique for Estimating Rain Parameters from Rain Noise Measurements

The measurement of global precipitation is of great importance in climate modeling since the release of latent heat associated with tropical convection is one of the pricipal driving mechanisms of atmospheric circulation.Knowledge of the larger-scale precipitation field also has important potential applications in the generation of initial conditions for numerical weather prediction models Knowledge of the relationship between rainfall intensity and kinetic energy, and its variations in time and space is important for erosion prediction. Vegetation on earth also greatly depends on the total amount of rainfall as well as the drop size distribution (DSD) in rainfall.While methods using visible,infrared, and microwave radiometer data have been shown to yield useful estimates of precipitation, validation of these products for the open ocean has been hampered by the limited amount of surface rainfall measurements available for accurate assessement, especially for the tropical oceans.Surface rain fall measurements(often called the ground truth)are carried out by rain gauges working on various principles like weighing type,tipping bucket,capacitive type and so on.The acoustic technique is yet another promising method of rain parameter measurement that has many advantages. The basic principle of acoustic method is that the droplets falling in water produce underwater sound with distinct features, using which the rainfall parameters can be computed. The acoustic technique can also be used for developing a low cost and accurate device for automatic measurement of rainfall rate and kinetic energy of rain.especially suitable for telemetry applications. This technique can also be utilized to develop a low cost Disdrometer that finds application in rainfall analysis as well as in calibration of nozzles and sprinklers. This thesis is divided into the following 7 chapters, which describes the methodology adopted, the results obtained and the conclusions arrived at.

Highly conductive and transparent ZnO thin film using Chemical Spray Pyrolysis technique: Effect of doping and deposition parameters

In the present work we report the preparation details studies on ZnO thin films. ZnO thin films are prepared using cost effective deposition technique viz., Chemical Spray Pyrolysis (CSP). The method is very effective for large area preparation of the ZnO thin film. A new post-deposition process could also be developed to avoid the adsorption of oxygen that usually occurs after the spraying process i.e., while cooling. Studies were done by changing the various deposition parameters for optimizing the properties of ZnO thin film. Moreover, different methods of doping using various elements are also tried to enhance the conductivity and transparency of the film to make these suitable for various optoelectronic applications.

Methods for short-term control of Imperata grass in Peruvian Amazon

The traditional control of Imperata brasiliensis grasslands used by farmers in the Peruvian Amazon is to burn the grass. The objective of this study was to compare different methods of short-term control. Biological, mechanical, chemical and traditional methods of control were compared. Herbicide spraying and manual weeding have shown to be very effective in reducing above- and below-ground biomass growth in the first 45 days after slashing the grass, with effects persisting in the longer term, but both are expensive methods. Shading seems to be less effective in the short-term, whereas it influences the Imperata growth in the longer term. After one year shading, glyphosate application and weeding significantly reduced aboveground biomass by 94, 67 and 53%; and belowground biomass by 76, 65 and 58%, respectively, compared to control. We also found a significant decrease of Imperata rhizomes in soil during time under shading. Burning has proved to have no significant effect on Imperata growth. The use of shade trees in a kind of agroforestry system could be a suitable method for small farmers to control Imperata grasslands.

Untersuchungen zu Controlled Traffic Farming und satellitenbasierten Lenksystemen

Diese Arbeit behandelt Controlled Traffic Farming (CTF) Anbausysteme, bei denen für alle Arbeitsgänge satellitengesteuert immer dieselben Fahrspuren benutzt werden. Lässt sich mit CTF die Belastung des Bodens verringern und die Effizienz von Direktsaat-Anbausystemen steigern? Neben agronomischen und bodenphysikalischen Parametern wurden Auswirkungen von Lenksystemen und Umsetzungsmöglichkeiten von CTF in die Praxis untersucht. Die Analyse einer CTF-Umsetzung unter europäischen Bedingungen mit der Verwendung von Standardmaschinen zeigte, dass sich CTF-Anbausysteme mit den heute zur Verfügung stehenden Maschinen für Dauergrünland, Mähdruschfrüchte und Mais auf kleiner und grösser strukturierten Flächen relativ einfach mechanisieren lassen. Bei Zuckerrüben und Kartoffeln können Kompromisse notwendig sein. Generell erfordern CTF-Anbausysteme eine sorgfältige Planung und Umsetzung in die Praxis. Im dreijährigen Feldversuch (Winterweizen, Wintergerste, Kunstwiese mit Kleegrasmischung) auf einem Lehmboden wurde CTF-Direktsaat mit konventionell zufällig befahrenen Direktsaat- und Pflugverfahren verglichen. Unter CTF zeigte sich eine Differenzierung der nicht, gering und intensiv befahrenen Varianten. Auf dem vorliegenden kompakten Boden mit 1150 mm Jahresniederschlag waren die Unterschiede zwischen den nicht befahrenen Flächen und den mit niedrigem Kontaktflächendruck befahrenen Flächen eher gering. In den nicht befahrenen Flächen entwickelten Eindringwiderstand und Kohlendioxidgehalt der Bodenluft nach drei Jahren signifikant bessere Werte. Bodendichte und Porosität zeigten hingegen keinen eindeutig interpretierbaren Trend. Aufgrund teils suboptimaler Feldaufgänge liess sich keine generelle agronomische Tendenz ableiten. Die intensive Befahrung der Pflegefahrgassen zeigte allerdings klar negative bodenkundliche und planzenbauliche Auswirkungen. Es bietet sich daher an, vor allem für Pflegearbeiten permanent dieselben Fahrspuren zu nutzen. In der Untersuchung zu den Auswirkungen von Lenksystemen zeigten sich signifikante Vorteile von Lenksystemen in einer Verminderung der Fahrerbelastung und einer höheren Lenkgenauigkeit vor allem bei grossen Arbeitsbreiten ohne Spuranreisser. Die meisten anderen Messparameter waren mit Lenksystem leicht vorteilhafter als ohne, unterschieden sich aber nicht signifikant voneinander. Fahrer und naturräumliche Gegebenheiten wie die Schlagform hatten einen wesentlich grösseren Einfluss. Gesamthaft betrachtet erweitert CTF in Kombination mit weiteren Bodenschutzmass-nahmen die Möglichkeiten, Bodenverdichtungen zu vermeiden, den Bedarf an energieintensiver Bodenlocke-rung zu reduzieren und die Entwicklung einer stabileren Bodenstruktur mit höherer Tragfähigkeit zu fördern. Zusammen mit einer an Kultur und Anbausystem angepassten Saatbettbereitung und den in geraden Reihen einfacher durchführbaren mechanischen Pflegemassnahmen ergeben sich gute Voraussetzungen für die Gestaltung agronomisch leistungsfähiger und ökologisch nachhaltiger Anbausysteme.

Fabrication of Controlled Release Devices Using Supercritical Antisolvent Method

In this study, the supercritical antisolvent with enhanced mass transfer method (SASEM) is used to fabricate micro and nanoparticles of biocompatible and biodegradable polymer PLGA (poly DL lactide co glycolic acid). This process may be extended to the encapsulation of drugs in these micro and nanoparticles for controlled release purposes. Conventional supercritical antisolvent (SAS) process involves spraying a solution (organic solvent + dissolved polymer) into supercritical fluid (CO[subscript 2]), which acts as an antisolvent. The high rate of mass transfer between organic solvent and supercritical CO[subscript 2] results in supersaturation of the polymer in the spray droplet and precipitation of the polymer as micro or nanoparticles occurs. In the SASEM method, ultrasonic vibration is used to atomize the solution entering the high pressure with supercritical CO[subscript 2]. At the same time, the ultrasonic vibration generated turbulence in the high pressure vessel, leading to better mass transfer between the organic solvent and the supercritical CO₂. In this study, two organic solvents, acetone and dichloromethane (DCM) were used in the SASEM process. Phase Doppler Particle Analyzer (PDPA) was used to study the ultrasonic atomization of liquid using the ultrasonic probe for the SASEM process. Scanning Electron Microscopy (SEM) was used to study the size and morphology of the polymer particles collected at the end of the process.

Análisis del papel de la política de erradicación forzosa con glifosato en relación a las dinámicas del conflicto armado en Nariño años 2000 - 2006

La concentración de la política de fumigacion con glifosato en regiones como el Putumayo y Caquetá, trajo consigo un enorme desplazamiento de los cultivos de coca hacia Nariño (efecto globo). Motivados por ejercer un control estratégico de estos nuevos recursos, los grupos armados ilegales reflejaron un creciente interés por copar el territorio, fomentando una cruenta lucha que condujo a una degradación de las dinámicas del conflicto armado en la región.

Dynamics of convectively driven banded jets in the laboratory

The banded organization of clouds and zonal winds in the atmospheres of the outer planets has long fascinated observers. Several recent studies in the theory and idealized modeling of geostrophic turbulence have suggested possible explanations for the emergence of such organized patterns, typically involving highly anisotropic exchanges of kinetic energy and vorticity within the dissipationless inertial ranges of turbulent flows dominated (at least at large scales) by ensembles of propagating Rossby waves. The results from an attempt to reproduce such conditions in the laboratory are presented here. Achievement of a distinct inertial range turns out to require an experiment on the largest feasible scale. Deep, rotating convection on small horizontal scales was induced by gently and continuously spraying dense, salty water onto the free surface of the 13-m-diameter cylindrical tank on the Coriolis platform in Grenoble, France. A “planetary vorticity gradient” or “β effect” was obtained by use of a conically sloping bottom and the whole tank rotated at angular speeds up to 0.15 rad s−1. Over a period of several hours, a highly barotropic, zonally banded large-scale flow pattern was seen to emerge with up to 5–6 narrow, alternating, zonally aligned jets across the tank, indicating the development of an anisotropic field of geostrophic turbulence. Using particle image velocimetry (PIV) techniques, zonal jets are shown to have arisen from nonlinear interactions between barotropic eddies on a scale comparable to either a Rhines or “frictional” wavelength, which scales roughly as (β/Urms)−1/2. This resulted in an anisotropic kinetic energy spectrum with a significantly steeper slope with wavenumber k for the zonal flow than for the nonzonal eddies, which largely follows the classical Kolmogorov k−5/3 inertial range. Potential vorticity fields show evidence of Rossby wave breaking and the presence of a “hyperstaircase” with radius, indicating instantaneous flows that are supercritical with respect to the Rayleigh–Kuo instability criterion and in a state of “barotropic adjustment.” The implications of these results are discussed in light of zonal jets observed in planetary atmospheres and, most recently, in the terrestrial oceans.

Bt cotton, pesticides, labour and health - A case study of smallholder farmers in the Makhathini Flats, Republic of South Africa

This paper describes some of the results of a detailed farm-level survey of 32 small-scale cotton farmers in the Makhathini Flats region of South Africa. The aim was to assess and measure some of the impacts (especially in terms of savings in pesticide and labour as well as benefits to human health) attributable to the use of insect-tolerant Bt cotton. The study reveals a direct cost benefit for Bt growers of SAR416 ($51) per hectare per season due to a reduction in the number of insecticide applications. Cost savings emerged in the form of lower requirements for pesticide, but also important were reduced requirements for water and labour. The reduction in the number of sprays was particularly beneficial to women who do some spraying and children who collect water and assist in spraying. The increasing adoption rate of Bt cotton appears to have a health benefit measured in terms of reported rates of accidental insecticide poisoning. These appear to be declining as the uptake of Bt cotton increases. However, the understanding of refugia and their management by local farmers are deficient and need improving. Finally, Bt cotton growers emerge as more resilient in absorbing price fluctuations.