Examining the effects of balloon control ring on ring spinning

The ring spinning process has been used to produce fine and high quality staple fibre yarns. The stability of the rotating yarn loop (i.e. balloon) between the yarn-guide and the traveller-ring is crucial to the success and economics of this process. Balloon control rings are used to contain the yarn-loop, by reducing the yarn tension and decreasing the balloon flutter instability. Flutter instability here refers to the uncontrolled changes in a ballooning yarn under dynamic forces, including the air drag. Due to the significant variation in the length and radius of the balloon during the bobbin filling process, the optimal location for the balloon control ring is not easily determined. In order to address this difficulty, this study investigates the variation in the radius of a free balloon and examines the effect of balloon control rings of various diameters at different locations on yarn tension and balloon flutter stability. The results indicate that the maximum radius of a free balloon and its corresponding position depend not only on the yarn-length to balloon-height ratio, but also on yarn type and count. A control ring of suitable radius and position can significantly reduce yarn tension and decrease flutter instability of free single-loop balloons. While the balloon control rings are usually fixed to, and move in sinc with, the ring frame, results reported in this study suggest that theoretically, a balloon control ring that always remains approximately half way between the yarn-guide and the ring rail during spinning can lead to significant reduction in yarn tension.

Do features of public open spaces vary according to neighbourhood socio-economic status?

This study examined the relations between neighbourhood socio-economic status and features of public open spaces (POS) hypothesised to influence children's physical activity. Data were from the first follow-up of the Children Living in Active Neighbourhoods (CLAN) Study, which involved 540 families of 5–6 and 10–12-year-old children in Melbourne, Australia. The Socio-Economic Index for Areas Index (SEIFA) of Relative Socio-economic Advantage/Disadvantage was used to assign a socioeconomic index score to each child's neighbourhood, based on postcode. Participant addresses were geocoded using a Geographic Information System. The Open Space 2002 spatial data set was used to identify all POS within an 800 m radius of each participant's home. The features of each of these POS (1497) were audited. Variability of POS features was examined across quintiles of neighbourhood SEIFA. Compared with POS in lower socioeconomic neighbourhoods, POS in the highest socioeconomic neighbourhoods had more amenities (e.g. picnic tables and drink fountains) and were more likely to have trees that provided shade, a water feature (e.g. pond, creek), walking and cycling paths, lighting, signage regarding dog access and signage restricting other activities. There were no differences across neighbourhoods in the number of playgrounds or the number of recreation facilities (e.g. number of sports catered for on courts and ovals, the presence of other facilities such as athletics tracks, skateboarding facility and swimming pool). This study suggests that POS in high socioeconomic neighbourhoods possess more features that are likely to promote physical activity amongst children.

Promoting transportation cycling for women : the role of bicycle infrastructure

Objective.
Females are substantially less likely than males to cycle for transport in countries with low bicycle transport mode share. We investigated whether female commuter cyclists were more likely to use bicycle routes that provide separation from motor vehicle traffic.
Methods.
Census of cyclists observed at 15 locations (including off-road bicycle paths, on-road lanes and roads with no bicycle facilities) within a 7.4 km radius of the central business district (CBD) of Melbourne, Australia, during peak commuting times in February 2004.
Results.
6589 cyclists were observed, comprising 5229 males (79.4%) and 1360 females (20.6%). After adjustment for distance of the bicycle facility from the CBD, females showed a preference for using off-road paths rather than roads with no bicycle facilities (odds ratio [OR] = 1.43, 95% confidence interval [CI]: 1.12, 1.83), or roads with on-road bicycle lanes (OR = 1.34, 95% CI: 1.03, 1.75).
Conclusions.
Consistent with gender differences in risk aversion, female commuter cyclists preferred to use routes with maximum separation from motorized traffic. Improved cycling infrastructure in the form of bicycle paths and lanes that provide a high degree of separation from motor traffic is likely to be important for increasing transportation cycling amongst under-represented population groups such as women.

Are safety-related features of the road environment associated with smaller declines in physical activity among youth?

This study examined how objective measures of the local road environment related to safety were associated with change in physical activity (including active transport) among youth. Few longitudinal studies have examined the impact of the road environment on physical activity among children/adolescents in their neighborhoods. Participants were children aged 8–9 years (n=170) and adolescents aged 13–15 years (n=276) in 2004. Data were collected in 2004 and 2006 during followup of participants recruited initially in 2001 from 19 primary schools in Melbourne, Australia. Walking/cycling to local destinations was parent-reported for children and self-reported by adolescents. Moderate-to-vigorous physical activity (MVPA) during nonschool hours was recorded using accelerometers. Road environment features in each participant’s neighborhood (area within 800 m radius of their home) were measured objectively using a Geographical Information System. Linear regression analyses examined associations between road features and changes in active transport (AT) and MVPA over 2 years. Children’s AT increased but MVPA levels decreased in both age groups; on average, younger girls recorded the greatest declines. The number of traffic/pedestrian lights was associated with ΔAT among younger girls (B=0.45, p=0.004). The total length of walking tracks (in meters) was associated with ΔAT among younger girls (B=0.0016, p=0.015) and adolescent girls (B=0.0016, p=0.002). For adolescent boys, intersection density was associated with ΔAT (B=0.03, p=0.030). Slow points were associated with ΔMVPA among younger boys before school (B=1.55, p=0.021), while speed humps were associated with ΔMVPA among adolescent boys after school (B=0.23, p=0.015). There were many associations for adolescent girls: for example, the total length of local roads (B=0.49, p=0.005), intersection density (B=0.05, p=0.036), and number of speed humps (B=0.33, p=0.020) were associated with ΔMVPA during nonschool hours. Safety-related aspects of the built environment are conducive to physical activity among youth and may help stem age-related declines in physical activity. Passive road safety interventions may promote AT and physical activity among less active girls, in particular.

Characterization of supported cylinder-planar germanium waveguide sensors with synchrotron Infrared radiation

Cylinder-planar Ge waveguides are being developed as evanescent-wave sensors for chemical microanalysis. The only non-planar surface is a cylinder section having a 300-mm radius of curvature. This confers a symmetric taper, allowing for direct coupling into and out of the waveguide's 1-mm² end faces while obtaining multiple reflections at the central <30-μm-thick sensing region. Ray-optic calculations indicate that the propagation angle at the central minimum has a strong nonlinear dependence on both angle and vertical position of the input ray. This results in rather inefficient coupling of input light into the off-axis modes that are most useful for evanescent-wave absorption spectroscopy. Mode-specific performance of the cylinder-planar waveguides has also been investigated experimentally. As compared to a blackbody source, the much greater brightness of synchrotron-generated infrared (IR) radiation allows a similar total energy throughput, but restricted to a smaller fraction of the allowed waveguide modes. However, such angle-selective excitation results in a strong oscillatory interference pattern in the transmission spectra. These spectral oscillations are the principal technical limitation on using synchrotron radiation to measure evanescent-wave absorption spectra with the thin waveguides.

Application of advanced analytical techniques to study structure-property relationship of hot rolled high strength low alloy steel

The microstructure-property relationship in conventional high strength low alloy (HSLA) steel was evaluated using data obtained from transmission electron microscopy (TEM) and atom probe tomography (APT). Atom probe tomography allowed the characterisation of fine TiC particles with average radius of 3±1·2 nm that were not observed by TEM. The increase in the yield strength of steel due to the presence of fine precipitates was calculated to be 128 MPa.

Molecular organization and viscosity of a thin film of molten polymer between two surfaces as probed by force measurements

Measurements are presented of the force between two molecularly smooth mica surfaces immersed in liquid poly(dimethylsiloxane) (Dow Corning 200 of nominal viscosity 50 cS) over a range of film thicknesses from 3 to 200 nm. There is a repulsion, attributed to conformational restrictions, when the polymer molecules are confined to a gap less than about 15 nm thick. In extremely thin films (<5 nm) the force is an oscillatory function of thickness with a repeat spacing corresponding to the width of the polymer molecule, which suggests that the polymer segments are arranged in layers near the solid surfaces. Dynamic force measurements show that the polymer has a viscosity equal to its bulk value even in very thin films, but a region next to each surface, only about one radius of gyration thick, does not flow. Saturation of the polymer with water destabilizes the film when it is very thin.

Spectroscopic characterization of alkali-metal exchanged natrolites

Synchrotron infrared (IR) and micro-Raman spectroscopic studies have been performed on zeolite natrolites as a function of the non-framework composition at ambient conditions. This establishes the spectroscopic characterization of the ion-exchanged natrolites in the alkali-metal series both in the as-prepared hydrated (M-NAT-hyd, M = Li, Na, K, Rb, and Cs) and some stable dehydrated forms (M-NAT-deh, M = Rb and Cs). The former series exhibits non-framework cation-size dependent opening of the helical channels to span ca. 21° range in terms of the chain rotation angle, ? (or ca. 45° range in terms of the chain bridging angle, T-O2-T). For these hydrated phases, both IR and Raman spectra reveal that the degree of the red-shifts in the frequencies of the helical 8-ring channel as well as the 4-ring unit is proportional to the ionic radius of the non-framework cations. Linear fits to the data show negative slopes of -55.7 from Raman and -18.3 from IR in the 8-ring frequencies and ionic radius relationship. The spectroscopic data are also used to identify the modes of the dehydration-induced "collapse" of the helical 8-ring channels as observed in the stable anhydrous Rb-NAT-deh and Cs-NAT-deh. In addition, we demonstrate that the spectroscopic data in the hydrated series can be used to distinguish different water arrangements along the helical channels based on the frequency shifts in the H-O-H bending band and the changes in the O-H stretching vibration modes.

Identification of surface heterogeneity effects in cyclic voltammograms derived from analysis of an individually addressable gold array electrode

Voltammetric behavior at gold electrodes in aqueous media is known to be strongly dependent on electrode polishing and history. In this study, an electrode array consisting of 100 nominally identical and individually addressable gold disks electrodes, each with a radius of 127 µm, has been fabricated. The ability to analyze both individual electrode and total array performance enables microscopic aspects of the overall voltammetric response arising from variable levels of inhomogeneity in each electrode to be identified. The array configuration was initially employed with the reversible and hence relatively surface insensitive [Ru(NH₃)₆]^3+/2+ reaction and then with the more highly surface sensitive quasi-reversible [Fe(CN)₆]^3−/4− process. In both these cases, the reactants and products are solution soluble and, at a scan rate of 50 mV s⁻¹, each electrode in the array is assumed to behave independently, since no evidence of overlapping of the diffusion layers was detected. As would be expected, the variability of the individual electrodesʼ responses was significantly larger than found for the summed electrode behavior. In the case of cytochrome c voltammetry at a 4,4′-dipyridyl disulfide modified electrode, a far greater dependence on electrode history and electrode heterogeneity was detected. In this case, voltammograms derived from individual electrodes in the gold array electrode exhibit shape variations ranging from peak to sigmoidal. However, again the total response was always found to be well-defined. This voltammetry is consistent with a microscopic model of heterogeneity where some parts of each chemically modified electrode surface are electroactive while other parts are less active. The findings are consistent with the common existence of electrode heterogeneity in cyclic voltammetric responses at gold electrodes, that are normally difficult to detect, but fundamentally important, as electrode nonuniformity can give rise to subtle forms of kinetic and other forms of dispersion.

An experimental investigation of edge strain and bow in roll forming a V-section

V-sections were roll formed from two grades of steel, and the strain on the top and bottom of the strip near the edge was measured using electrical resistance strain gauges. The channels were bent to a radius of 2 and 15 mm along the centerline. The steel strips were of mild and dual phase steel of yield strength 367 MPa and 597 MPa respectively. The longitudinal bow was measured using a 3-dimensional scanning system. The strain measurements were analysed to determine bending and mid-surface strains at the edge during forming. The peak longitudinal edge strain increased with material yield strength for both profile radii. For the 15 mm radius, the bow was larger in the dual phase steel than in the mild steel. For the 2 mm profile radius, the bow was smaller compared with the 15 mm profile radius and it was similar for both steels. It was observed that the difference between the peak longitudinal edge strain and yield strength to Youngs modulus ratio of the material is an important factor in determining longitudinal bow.

Roll-formability of cryo-rolled ultrafine aluminium sheet

Ultrafine-grain aluminium sheet was produced by rolling at cryogenic (CR) and at room temperature (RTR). Commercial purity aluminium plate was reduced in 30 passes from an initial material thickness of 10 mm to a final thickness of 2 mm (80% reduction). Tensile stress and strength were significantly increased while total elongation was drastically reduced. It was found that despite the low tensile elongation both materials are able to accommodate high localised strains in the neck leading to a high reduction in area. The formability of the material was further investigated in bending operations. A minimum bending radius of 6 mm (CR) and 5 mm (RTR) was found and pure bending tests showed homogeneous forming behaviour for both materials. In V-die bending the cryo-rolled material showed strain localisations across the final radius and kinking of the sample. It has been found that even if the total elongation in tension is close to zero leading to early failure in V-die bending, ultra-fine grained and low ductile sheet metals can be roll formed to simple section shapes with small radii using commercial roll forming equipment.

The effect of high yttrium solute concentration on the twinning behaviour of magnesium alloys

The deformation behaviour of two single phase binary alloys, Mg-5Y and Mg-10Y, have been examined. In compression, two twin types were observed, the common {101¯2} twin as well as the less common {112¯1} extension twin. It is shown that the {112¯1} twin is much less sensitive to solute concentration than the {101¯2} twin, and it is suggested that the simple atomic shuffle of the {112¯1} twin reduces the solute strengthening imparted by Y additions. The common {101¯2} twin showed significant hardening as a result of alloying with Y. An analysis of solute behaviour has indicated that of the four chemical parameters investigated, i.e. atomic size, shear modulus, electronegativity and solute distribution, it appears to be the larger atomic radius of Y compared to Mg that increases the stress required to activate the {101¯2} twin. It is suggested that the large atomic radius inhibits the atomic shuffling process which accompanies the twinning shear in this twin type.

Wind Power Suitability Analysis for the Gulf of Maine

This map shows one option for a viable energy source that is clean, free and endless: wind power. This map shows that the coast of Maine has the potential space and wind speed to be a location for wind farms. Four NOAA buoys placed in different locations along the Maine coast are the source of the wind speed data for this project. The average wind speed of every ten minutes of every day for the year 2004 were averaged so that each buoy was represented by one number of wind speed measured in meters/ second. The values in between these four buoys were estimated, or interpolated, using ArcGIS. Other factors that I took into consideration during this lab were distance from airports (no wind farm can be with in a three mile radius of an airport ) and distance from counties (no one wants an offshore wind farm that obstructs their view). I calculated the most appropriate locations for a wind farm in ArcGIS, by adding these three layers. The final output shows an area along Mt. Desert to be the most appropriate for development.

SEDIMENT BIOTURBATION POTENTIAL of UCA RAPAX and UCA URUGUAYENSIS AS A RESULT of THEIR FEEDING ACTIVITY

Bioturbation of mangrove sediments by Uca uruguayensis (Nobili, 1901) and U. rapax (Smith, 1870) was compared based on the grain-size composition and organic content in surface sediment around the burrow and feeding pellets in two mangrove zones of the Sao Vicente Estuary, state of São Paulo, Brazil. For each species, 25 burrows with active crabs were selected. All pellets within a 15-cm radius of each burrow were carefully collected; samples of substrate were taken; and the crab occupant was excavated, sexed, and measured for carapace width (CW). The number of spoon-tipped setae on the second maxilliped of each species was estimated; U. uruguayensis showed more of these setae than U. rapax. For both species, the sediment post-processed by feeding activity (feeding pellets) showed a similar increase of coarser fractions and a smaller organic content. However. U. uruguayensis was more efficient in removing organic matter (88.1%) from the sediment than U. rapax (37.5%). These results suggest that different numbers of spoon-tipped setae on the second maxillipeds of the fiddler crabs do not affect the potential for grain-size selection, but result in differing abilities to remove organic matter from the sediment.

Electrochemical evaluation of the a carbon-paste electrode modified with spinel manganese(IV) oxide under flow conditions for amperometric determination of lithium

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)