Highly thermally responsive hybrid in-fiber sSlab waveguide grating structure with a plastic core and a silica cladding

A 1.2(height)×125(depth)×500(length) micro-slot was engraved along a fiber Bragg grating by chemically assisted femtosecond laser processing. By filling epoxy and UV-curing, waveguide with plastic-core and silica-cladding was created, presenting high thermal responding coefficient of 211pm/°C.

Fabry-Perot micro-structured polymer optical fibre sensors for opto-acoustic endoscopy

Opto-Acoustic Endoscopy (OAE) requires sensors with a high sensitivity and small physical dimensions in order to facilitate integration into an endoscope of less than 1mm in diameter. We present fibre Bragg grating (FBG) and Fabry- Perot intrinsic fibre sensors for ultrasound detection. We present a structure profile characterisation setup to analyse tune the fibre sensors in preparation for ultrasonic detection. We evaluate the suitability of the different structures and grating parameters for ultrasonic sensing. By analysing the prepared gratings, we enable the optimisation of the profile and a simplification of the detection regime for an optimal interferometric OAE configuration.

Refractive index and temperature sensitivity characteristics of a micro-slot fiber Bragg grating

Fabrication and characterization of a UVinscribed fiber Bragg grating (FBG) with a micro-slot liquid core is presented. Femtosecond (fs) laser patterning/chemical etching technique was employed to engrave a micro-slot with dimensions of 5.74 μm(h) × 125 μm(w) × 1388.72 μm(l) across the whole grating. The device has been evaluated for refractive index (RI) and temperature sensitivities and exhibited distinctive thermal response and RI sensitivity beyond the detection limit of reported fiber gratings. This structure has not just been RI sensitive, but also maintained the robustness comparing with the bare core FBGs and long-period gratings with the partial cladding etched off. © 2012 Optical Society of America.

Self-assembled SnO2 micro- and nanosphere-based gas sensor thick films from an alkoxide-derived high purity aqueous colloid precursor

Tin oxide is considered to be one of the most promising semiconductor oxide materials for use as a gas sensor. However, a simple route for the controllable build-up of nanostructured, sufficiently pure and hierarchical SnO2 structures for gas sensor applications is still a challenge. In the current work, an aqueous SnO2 nanoparticulate precursor sol, which is free of organic contaminants and sorbed ions and is fully stable over time, was prepared in a highly reproducible manner from an alkoxide Sn(OR)4 just by mixing it with a large excess of pure neutral water. The precursor is formed as a separate liquid phase. The structure and purity of the precursor is revealed using XRD, SAXS, EXAFS, HRTEM imaging, FTIR, and XRF analysis. An unconventional approach for the estimation of the particle size based on the quantification of the Sn-Sn contacts in the structure was developed using EXAFS spectroscopy and verified using HRTEM. To construct sensors with a hierarchical 3D structure, we employed an unusual emulsification technique not involving any additives or surfactants, using simply the extraction of the liquid phase, water, with the help of dry butanol under ambient conditions. The originally generated crystalline but yet highly reactive nanoparticles form relatively uniform spheres through self-assembly and solidify instantly. The spheres floating in butanol were left to deposit on the surface of quartz plates bearing sputtered gold electrodes, producing ready-for-use gas sensors in the form of ca. 50 μm thick sphere-based-films. The films were dried for 24 h and calcined at 300°C in air before use. The gas sensitivity of the structures was tested in the temperature range of 150-400°C. The materials showed a very quickly emerging and reversible (20-30 times) increase in electrical conductivity as a response to exposure to air containing 100 ppm of H2 or CO and short (10 s) recovery times when the gas flow was stopped.

Development and implementation of a tool to assess the micro/macro elements in an organization

This study examines the congruency of planning between organizational structure and process, through an evaluation and planning model known as the Micro/Macro Dynamic Planning Grid. The model compares day-to-day planning within an organization to planning imposed by organizational administration and accrediting agencies. A survey instrument was developed to assess the micro and macro sociological analysis elements utilized by an organization.^ The Micro/Macro Dynamic Planning Grid consists of four quadrants. Each quadrant contains characteristics that reflect the interaction between the micro and macro elements of planning, objectives and goals within an organization. The Over Macro/Over Micro, Quadrant 1, contains attributes that reflect a tremendous amount of action and ongoing adjustments, typical of an organization undergoing significant changes in either leadership, program and/or structure. Over Macro/Under Micro, Quadrant 2, reflects planning characteristics found in large, bureaucratic systems with little regard given to the workings of their component parts. Under Macro/Under Micro, Quadrant 3, reflects the uncooperative, uncoordinated organization, one that contains a multiplicity of viewpoints, language, objectives and goals. Under Macro/Under Micro, Quadrant 4 represents the worst case scenario for any organization. The attributes of this quadrant are very reactive, chaotic, non-productive and redundant.^ There were three phases to the study: development of the initial instrument, pilot testing the initial instrument and item revision, and administration and assessment of the refined instrument. The survey instrument was found to be valid and reliable for the purposes and audiences herein described.^ In order to expand the applicability of the instrument to other organizational settings, the survey was administered to three professional colleges within a university.^ The first three specific research questions collectively answered, in the affirmative, the basic research question: Can the Micro/Macro Dynamic Planning Grid be applied to an organization through an organizational development tool? The first specific question: Can an instrument be constructed that applies the Micro/Macro Dynamic Planning Grid? The second specific research question: Is the constructed instrument valid and reliable? The third specific research question: Does an instrument that applies the Micro/Macro Dynamic Planning Grid assess congruency of micro and macro planning, goals and objectives within an organization? The fourth specific research question: What are the differences in the responses based on roles and responsibilities within an organization? involved statistical analysis of the response data and comparisons obtained with the demographic data. (Abstract shortened by UMI.) ^

A micro-opto-electro-mechanical system (MOEMS) for microstructure manipulation

Microstructure manipulation is a fundamental process to the study of biology and medicine, as well as to advance micro- and nano-system applications. Manipulation of microstructures has been achieved through various microgripper devices developed recently, which lead to advances in micromachine assembly, and single cell manipulation, among others. Only two kinds of integrated feedback have been demonstrated so far, force sensing and optical binary feedback. As a result, the physical, mechanical, optical, and chemical information about the microstructure under study must be extracted from macroscopic instrumentation, such as confocal fluorescence microscopy and Raman spectroscopy. In this research work, novel Micro-Opto-Electro-Mechanical-System (MOEMS) microgrippers are presented. These devices utilize flexible optical waveguides as gripping arms, which provide the physical means for grasping a microobject, while simultaneously enabling light to be delivered and collected. This unique capability allows extensive optical characterization of the structure being held such as transmission, reflection, or fluorescence. The microgrippers require external actuation which was accomplished by two methods: initially with a micrometer screw, and later with a piezoelectric actuator. Thanks to a novel actuation mechanism, the "fishbone", the gripping facets remain parallel within 1 degree. The design, simulation, fabrication, and characterization are systematically presented. The devices mechanical operation was verified by means of 3D finite element analysis simulations. Also, the optical performance and losses were simulated by the 3D-to-2D effective index (finite difference time domain FDTD) method as well as 3D Beam Propagation Method (3D-BPM). The microgrippers were designed to manipulate structures from submicron dimensions up to approximately 100 μm. The devices were implemented in SU-8 due to its suitable optical and mechanical properties. This work demonstrates two practical applications: the manipulation of single SKOV-3 human ovarian carcinoma cells, and the detection and identification of microparts tagged with a fluorescent "barcode" implemented with quantum dots. The novel devices presented open up new possibilities in the field of micromanipulation at the microscale, scalable to the nano-domain.

Through wafer 3D Vertical Micro-Coaxial Probe for high frequency material characterization and millimeter wave packaging systems

This work presents the development of an in-plane vertical micro-coaxial probe using bulk micromachining technique for high frequency material characterization. The coaxial probe was fabricated in a silicon substrate by standard photolithography and a deep reactive ion etching (DRIE) technique. The through-hole structure in the form of a coaxial probe was etched and metalized with a diluted silver paste. A co-planar waveguide configuration was integrated with the design to characterize the probe. The electrical and RF characteristics of the coaxial probe were determined by simulating the probe design in Ansoft's High Frequency Structure Simulator (HFSS). The reflection coefficient and transducer gain performance of the probe was measured up to 65 GHz using a vector network analyzer (VNA). The probe demonstrated excellent results over a wide frequency band, indicating its ability to integrate with millimeter wave packaging systems as well as characterize unknown materials at high frequencies. The probe was then placed in contact with 3 materials where their unknown permittivities were determined. To accomplish this, the coaxial probe was placed in contact with the material under test and electromagnetic waves were directed to the surface using the VNA, where its reflection coefficient was then determined over a wide frequency band from dc-to -65GHz. Next, the permittivity of each material was deduced from its measured reflection coefficients using a cross ratio invariance coding technique. The permittivity results obtained when measuring the reflection coefficient data were compared to simulated permittivity results and agreed well. These results validate the use of the micro-coaxial probe to characterize the permittivity of unknown materials at high frequencies up to 65GHz.

Projeto de absorvedores de micro-ondas integrados com superfícies seletivas em frequência

Considering the fact that, the use of wireless communication systems has grown too fast, investigations concerning absorbers of electromagnetic waves has called closer attention of researchers. It is applicable from indoor systems to military applications. Paralleling with this growth, some extremely relevant investigations through Frequency Selective Surfaces (FSS) allows its filter property to be applicable in several systems, for example: reflector antennas, band-pass radomes, and absorbers, which are the main objective of this work. Therefore, the main goal of this work concerns to design micro-waves absorbers through FSS. Thus, the methodology consists basically in two steps: the first step concerns a theoretical and numerical analysis of the structures involved in the process of absorption, the second step, the analysis of the cascaded structures. In order to carry out the analysis, the Equivalent Circuit Method will be used. This method provides characteristics of transmission from the structure, for a plane wave incidence and it requires an extremely limited computing resource in relation if compared to full wave analyses method. Hence, it is useful to allow fast predictions of the development of the structures. Furthermore, a spreading matrix will be used in order to cascade the conductive FSS and the resistive FSS achieving absorption characteristics in the designed band. The experimental results used for the analysis are found in the literature due to the difficulty of building soon, given that it is not a simple construction technique. To conclude, a mathematical development through the Equivalent Circuit Method of a FSS modeling with cross-dipole geometry and a resistive FSS will be presented, as well as the cascading involving the two structures. The same setting is used with a square loop geometry. Besides it, the next steps will be discussed in the conclusion.

Theoretical modeling and experimental validation of fluid-loaded micro rectangular plates

This paper presents a theoretical model on the vibration analysis of micro scale fluid-loaded rectangular isotropic plates, based on the Lamb's assumption of fluid-structure interaction and the Rayleigh-Ritz energy method. An analytical solution for this model is proposed, which can be applied to most cases of boundary conditions. The dynamical experimental data of a series of microfabricated silicon plates are obtained using a base-excitation dynamic testing facility. The natural frequencies and mode shapes in the experimental results are in good agreement with the theoretical simulations for the lower order modes. The presented theoretical and experimental investigations on the vibration characteristics of the micro scale plates are of particular interest in the design of microplate based biosensing devices. Copyright © 2009 by ASME.

A Micro-Opto-Electro-Mechanical System (MOEMS) for Microstructure Manipulation

Microstructure manipulation is a fundamental process to the study of biology and medicine, as well as to advance micro- and nano-system applications. Manipulation of microstructures has been achieved through various microgripper devices developed recently, which lead to advances in micromachine assembly, and single cell manipulation, among others. Only two kinds of integrated feedback have been demonstrated so far, force sensing and optical binary feedback. As a result, the physical, mechanical, optical, and chemical information about the microstructure under study must be extracted from macroscopic instrumentation, such as confocal fluorescence microscopy and Raman spectroscopy. In this research work, novel Micro-Opto-Electro-Mechanical-System (MOEMS) microgrippers are presented. These devices utilize flexible optical waveguides as gripping arms, which provide the physical means for grasping a microobject, while simultaneously enabling light to be delivered and collected. This unique capability allows extensive optical characterization of the structure being held such as transmission, reflection, or fluorescence. The microgrippers require external actuation which was accomplished by two methods: initially with a micrometer screw, and later with a piezoelectric actuator. Thanks to a novel actuation mechanism, the “fishbone”, the gripping facets remain parallel within 1 degree. The design, simulation, fabrication, and characterization are systematically presented. The devices mechanical operation was verified by means of 3D finite element analysis simulations. Also, the optical performance and losses were simulated by the 3D-to-2D effective index (finite difference time domain FDTD) method as well as 3D Beam Propagation Method (3D-BPM). The microgrippers were designed to manipulate structures from submicron dimensions up to approximately 100 µm. The devices were implemented in SU-8 due to its suitable optical and mechanical properties. This work demonstrates two practical applications: the manipulation of single SKOV-3 human ovarian carcinoma cells, and the detection and identification of microparts tagged with a fluorescent “barcode” implemented with quantum dots. The novel devices presented open up new possibilities in the field of micromanipulation at the microscale, scalable to the nano-domain.

Porous Materials with Tunable Structure and Mechanical Properties via Templated Layer-by-Layer Assembly

The deposition of stiff and strong coatings onto porous templates offers a novel strategy for fabricating macroscale materials with controlled architectures at the micro- and nanoscale. Here, layer-by-layer assembly is utilized to fabricate nanocomposite-coated foams with highly customizable properties by depositing polymer–nanoclay coatings onto open-cell foam templates. The compressive mechanical behavior of these materials evolves in a predictable manner that is qualitatively captured by scaling laws for the mechanical properties of cellular materials. The observed and predicted properties span a remarkable range of density-stiffness space, extending from regions of very soft elastomer foams to very stiff, lightweight honeycomb and lattice materials.

Spectral analysis of four 'hypervariable' AGN: a micro-needle in the haystack?

We analyze four extreme AGN transients to explore the possibility that they are caused by rare, high-amplitude microlensing events. These previously unknown type-I AGN are located in the redshift range 0.6-1.1 and show changes of > 1.5 magnitudes in the g-band on a timescale of ~years. Multi-epoch optical spectroscopy, from the William Herschel Telescope, shows clear differential variability in the broad line fluxes with respect to the continuum changes and also evolution in the line profiles. In two cases a simple point-source, point-lens microlensing model provides an excellent match to the long-term variability seen in these objects. For both models the parameter constraints are consistent with the microlensing being due to an intervening stellar mass object but as yet there is no confirmation of the presence of an intervening galaxy. The models predict a peak amplification of 10.3/13.5 and an Einstein timescale of 7.5/10.8 years respectively. In one case the data also allow constraints on the size of the CIII] emitting region, with some simplifying assumptions, to to be ~1.0-6.5 light-days and a lower limit on the size of the MgII emitting region to be > 9 light-days (half-light radii). This CIII] radius is perhaps surprisingly small. In the remaining two objects there is spectroscopic evidence for an intervening absorber but the extra structure seen in the lightcurves requires a more complex lensing scenario to adequately explain.

Estudo sobre a mortalidade e sobrevivência de micro e pequenas empresas natalenses e seus impactos nas políticas públicas pró-empreendedorismo

The principal purpose of this research was to investigate discriminant factors of survival and failure of micro and small businesses, and the impacts of these factors in the public politics for entrepreneurship in the State of Rio Grande do Norte. The data were ceded by SEBRAE/RN and the Commercial Committee of the Rio Grande do Norte State and it included the businesses that were registered in 2000, 2001 and 2002. According to the theoretical framework 3 groups of factors were defined Business Financial Structure, Entrepreneurial Preparation and Entrepreneurial Behavior , and the factors were studied in order to determine whether they are discriminant or not of the survival and business failure. A quantitative research was applied and advanced statistical techniques were used multivariate data analysis , beginning with the factorial analysis and after using the discriminant analysis. As a result, canonical discriminant functions were found and they partially explained the survival and business failure in terms of the factors and groups of factors. The analysis also permitted the evaluation of the public politics for entrepreneurship and it was verified, according to the view of the entrepreneurs, that these politics were weakly effective to avoid business failure. Some changes in the referred politics were suggested based on the most significant factors found.

Effect of soil structure on temporal and spatial dynamics of bacteria

Soil is a complex heterogeneous system comprising of highly variable and dynamic micro-habitats that have significant impacts on the growth and activity of resident microbiota. A question addressed in this research is how soil structure affects the temporal dynamics and spatial distribution of bacteria. Using repacked microcosms, the effect of bulk-density, aggregate sizes and water content on growth and distribution of introduced Pseudomonas fluorescens and Bacillus subtilis bacteria was determined. Soil bulk-density and aggregate sizes were altered to manipulate the characteristics of the pore volume where bacteria reside and through which distribution of solutes and nutrients is controlled. X-ray CT was used to characterise the pore geometry of repacked soil microcosms. Soil porosity, connectivity and soil-pore interface area declined with increasing bulk-density. In samples that differ in pore geometry, its effect on growth and extent of spread of introduced bacteria was investigated. The growth rate of bacteria reduced with increasing bulk-density, consistent with a significant difference in pore geometry. To measure the ability of bacteria to spread thorough soil, placement experiments were developed. Bacteria were capable of spreading several cm’s through soil. The extent of spread of bacteria was faster and further in soil with larger and better connected pore volumes. To study the spatial distribution in detail, a methodology was developed where a combination of X-ray microtopography, to characterize the soil structure, and fluorescence microscopy, to visualize and quantify bacteria in soil sections was used. The influence of pore characteristics on distribution of bacteria was analysed at macro- and microscales. Soil porosity, connectivity and soil-pore interface influenced bacterial distribution only at the macroscale. The method developed was applied to investigate the effect of soil pore characteristics on the extent of spread of bacteria introduced locally towards a C source in soil. Soil-pore interface influenced spread of bacteria and colonization, therefore higher bacterial densities were found in soil with higher pore volumes. Therefore the results in this showed that pore geometry affects the growth and spread of bacteria in soil. The method developed showed showed how thin sectioning technique can be combined with 3D X-ray CT to visualize bacterial colonization of a 3D pore volume. This novel combination of methods is a significant step towards a full mechanistic understanding of microbial dynamics in structured soils.

Large eddy simulation of shock boundary layer interaction control using micro-vortex generators

The performance of supersonic engine inlets and external aerodynamic surfaces can be critically affected by shock wave / boundary layer interactions (SBLIs), whose severe adverse pressure gradients can cause boundary layer separation. Currently such problems are avoided primarily through the use of boundary layer bleed/suction which can be a source of significant performance degradation. This study investigates a novel type of flow control device called micro-vortex generators (µVGs) which may offer similar control benefits without the bleed penalties. µVGs have the ability to alter the near-wall structure of compressible turbulent boundary layers to provide increased mixing of high speed fluid which improves the boundary layer health when subjected to flow disturbance. Due to their small size,µVGs are embedded in the boundary layer which provide reduced drag compared to the traditional vortex generators while they are cost-effective, physically robust and do not require a power source. To examine the potential of µVGs, a detailed experimental and computational study of micro-ramps in a supersonic boundary layer at Mach 3 subjected to an oblique shock was undertaken. The experiments employed a flat plate boundary layer with an impinging oblique shock with downstream total pressure measurements. The moderate Reynolds number of 3,800 based on displacement thickness allowed the computations to use Large Eddy Simulations without the subgrid stress model (LES-nSGS). The LES predictions indicated that the shock changes the structure of the turbulent eddies and the primary vortices generated from the micro-ramp. Furthermore, they generally reproduced the experimentally obtained mean velocity profiles, unlike similarly-resolved RANS computations. The experiments and the LES results indicate that the micro-ramps, whose height is h≈0.5δ, can significantly reduce boundary layer thickness and improve downstream boundary layer health as measured by the incompressible shape factor, H. Regions directly behind the ramp centerline tended to have increased boundary layer thickness indicating the significant three-dimensionality of the flow field. Compared to baseline sizes, smaller micro-ramps yielded improved total pressure recovery. Moving the smaller ramps closer to the shock interaction also reduced the displacement thickness and the separated area. This effect is attributed to decreased wave drag and the closer proximity of the vortex pairs to the wall. In the second part of the study, various types of µVGs are investigated including micro-ramps and micro-vanes. The results showed that vortices generated from µVGs can partially eliminate shock induced flow separation and can continue to entrain high momentum flux for boundary layer recovery downstream. The micro-ramps resulted in thinner downstream displacement thickness in comparison to the micro-vanes. However, the strength of the streamwise vorticity for the micro-ramps decayed faster due to dissipation especially after the shock interaction. In addition, the close spanwise distance between each vortex for the ramp geometry causes the vortex cores to move upwards from the wall due to induced upwash effects. Micro-vanes, on the other hand, yielded an increased spanwise spacing of the streamwise vortices at the point of formation. This resulted in streamwise vortices staying closer to the wall with less circulation decay, and the reduction in overall flow separation is attributed to these effects. Two hybrid concepts, named “thick-vane” and “split-ramp”, were also studied where the former is a vane with side supports and the latter has a uniform spacing along the centerline of the baseline ramp. These geometries behaved similar to the micro-vanes in terms of the streamwise vorticity and the ability to reduce flow separation, but are more physically robust than the thin vanes. Next, Mach number effect on flow past the micro-ramps (h~0.5δ) are examined in a supersonic boundary layer at M=1.4, 2.2 and 3.0, but with no shock waves present. The LES results indicate that micro-ramps have a greater impact at lower Mach number near the device but its influence decays faster than that for the higher Mach number cases. This may be due to the additional dissipation caused by the primary vortices with smaller effective diameter at the lower Mach number such that their coherency is easily lost causing the streamwise vorticity and the turbulent kinetic energy to decay quickly. The normal distance between the vortex core and the wall had similar growth indicating weak correlation with the Mach number; however, the spanwise distance between the two counter-rotating cores further increases with lower Mach number. Finally, various µVGs which include micro-ramp, split-ramp and a new hybrid concept “ramped-vane” are investigated under normal shock conditions at Mach number of 1.3. In particular, the ramped-vane was studied extensively by varying its size, interior spacing of the device and streamwise position respect to the shock. The ramped-vane provided increased vorticity compared to the micro-ramp and the split-ramp. This significantly reduced the separation length downstream of the device centerline where a larger ramped-vane with increased trailing edge gap yielded a fully attached flow at the centerline of separation region. The results from coarse-resolution LES studies show that the larger ramped-vane provided the most reductions in the turbulent kinetic energy and pressure fluctuation compared to other devices downstream of the shock. Additional benefits include negligible drag while the reductions in displacement thickness and shape factor were seen compared to other devices. Increased wall shear stress and pressure recovery were found with the larger ramped-vane in the baseline resolution LES studies which also gave decreased amplitudes of the pressure fluctuations downstream of the shock.