Swine deep bedding ashes as a mineral additive for cement based mortar

The sustainability of intensive swine production demands alternative destinations for the generated residues. Ashes from swine rice husk-based deep bedding were tested as a mineral addition for cement mortars. The ashes were obtained at 400 to 600ºC, ground and sieved through a 325 mesh sieve (# 0.045 mm). The characterization of the ashes included the determination of the index of pozzolanic activity with lime. The ashes were also tested as partial substitutes of Portland cement. The mortars were prepared using a cement:sand proportion of 1:1.5, and with water/cement ratio of 0.4. Three percentages of mass substitution of the cement were tested: 10, 20 and 30%. Mortar performances were assessed at 7 and 28 days determining their compressive strength. The chosen condition for calcinations at the laboratory scale was related to the maximum temperature of 600ºC since the resulting ashes contained vitreous materials and presented satisfactory values for the pozzolanic index under analysis. The pozzolanic activity indicated promising results for ashes produced at 600ºC as a replacement of up to 30% in cement masses.

Benign focal seizures of adolescence and neuropsychological findings in patients from community

RATIONALE: Benign focal seizures of adolescence (BFSA) described by Loiseau et al in 1972, is considered a rare entity, but maybe underdiagnosed. Although mild neuropsychological deficits have been reported in patients with benign epilepsies of childhood, these evaluations have not so far been described in BFSA. The aim of this study is to evaluate neuropsychological functions in BFSA with new onset seizures (<12 months). METHODS: Eight patients with BFSA (according to Loiseau et al, 1972, focal or secondarily tonic clonic generalized seizures between the ages of 10-18 yrs., normal neurologic examination, normal EEG or with mild focal abnormalities) initiated in the last 12 months were studied between July 2008 to May 2009. They were referred from the Pediatric Emergency Section of the Hospital Universitário of the University of Sao Paulo, a secondary care regionalized facility located in a district of middle-low income in Sao Paulo city, Brazil. The study was approved by the Ethics Committee of the Institution. All patients performed neurological, EEG, brain CT and neuropsychological evaluation which consisted of Raven's Special Progressive Matrices - General and Special Scale (according to different ages), Wechsler Children Intelligence Scale-WISC III with ACID Profile, Trail Making Test A/B, Stroop Test, Bender Visuo-Motor Test, Rey Complex Figure, Rey Auditory Verbal Learning Test-RAVLT, Boston Naming Test, Fluency Verbal for phonological and also conceptual patterns - FAS/Animals and Hooper Visual Organization Test. For academic achievement, we used a Brazilian test for named "Teste do Desempenho Escolar", which evaluates abilities to read, write and calculate according to school grade. RESULTS: There were 2 boys and 6 girls, with ages ranging from 10 yrs. 9 m to 14 yrs. 3 m. Most (7/8) of the patients presented one to two seizures and only three of them received antiepileptic drugs (AEDs). Six had mild EEG focal abnormalities and all had normal brain CT. All were literate, attended regular public schools and scored in a median range for IQ, and seven showed discrete higher scores for the verbal subtests. There were low scores for attention in different modalities in six patients, mainly in alternated attention as well as inhibitory subtests (Stroop test and Trail Making Test part B). Four of the latter cases who showed impairment both in alternated and inhibitory attention were not taking AEDs. Visual memory was impaired in five patients (Rey Complex Figure). Executive functions analysis showed deficits in working memory in five, mostly observed in Digits Indirect Order and Arithmetic tests (WISC III). Reading and writing skills were below the expected average for school grade in six patients according to the achievement scholar performance test utilized. One patient of this series who had the best scores in all tests was taking phenobarbital. CONCLUSIONS: Neuropsychological imbalance between normal IQ and mild dysfunctions such as in attention domain and in some executive abilities like working memory and planning, as well as difficulties in visual memory and in reading and writing, were described in this group of patients with BFSA from community. This may reflect mild higher level neurological dysfunctions in adolescence idiopathic focal seizures probably caused by an underlying dysmaturative epileptogenic process. Although academic problems often have multiple causes, a specific educational approach may be necessary in these adolescents, in order to improve their scholastic achievements, helping in this way, to decrease the stigma associated to epileptic seizures in the community.

Qualidade de vida e desempenho ocupacional de pacientes submetidos à cirurgia de epilepsia

OBJETIVO: este estudo teve como objetivo comparar a qualidade de vida e as áreas do desempenho ocupacional de pacientes epilépticos antes e doze meses após tratamento cirúrgico. METODOLOGIA: a amostra foi composta por 30 pacientes epilépticos que frequentavam o Centro de Cirurgia de Epilepsia da Faculdade de Medicina de São José do Rio Preto - FAMERP. Todos os participantes responderam a uma entrevista semiestruturada para coleta de dados sociodemográficos, ao Questionário de Qualidade de Vida em Epilepsia - 31 (QOLIE-31) e à Medida Canadense de Desempenho Ocupacional - MCDO. RESULTADOS: dezenove pacientes(63,3%) eram do sexo feminino e onze (36,7%) do sexo masculino, com idade entre 22 e 65 anos (42,1±11,9). Os resultados obtidos com o QOLIE-31 apontaram diferenças significativas em seis dos sete domínios que compõe o questionário quando comparados o período pré e pós-cirúrgico. A comparação dos resultados da COPM mostrou aumento significativo tanto na performance quanto na satisfação dos pacientes com suas atividades de vida diária, instrumentais de vida diária e de lazer. CONCLUSÃO: o tratamento cirúrgico se mostrou eficaz na melhora da qualidade de vida e no desempenho ocupacional o que pode traduzir-se a médio e longo prazo em integração social mais adequada para os pacientes epilépticos.

Ichthyoplankton distribution and abundance in the northern Todos os Santos and Camamu Bays, Bahia State - Brazil

The occurrence, distribution and abundance of ichthyoplankton in Todos os Santos and Camamu Bays were analyzed based on four samplings (winter 2003, summer 2003, winter 2004 and summer 2005). Samples were obtained by surface horizontal hauls, using a 200-µm mesh conical-cylinder plankton net. The distribution and abundance of eggs indicate a remarkable seasonal and annual variation of spawning activity in the region, especially when the two summer campaigns are compared. In summer 2003 the highest quantitative values were recorded, especially for Camamu, where the maximum reached 106.56 eggs.m-3, with an overall average of 43.46 eggs.m-3 for the two areas. In summer 2005 values were relatively low, the overall average being 3.49 eggs.m-3. The larval taxonomic composition is characterized by the predominance of gobiids, with small variation from summer to winter. Considering all the campaigns and samplings undertaken in both areas, larvae of 11 families were identified: Engraulidae, Clupeidae, Mugilidae, Atherinopsidae, Hemiramphidae, Syngnathidae, Blenniidae, Carangidae, Gobiidae, Achiridae and Tetraodontidae.

Obesidade na adolescência e seus principais fatores determinantes

O objetivo deste trabalho foi discutir os principais fatores ambientais determinantes do sobrepeso e da obesidade em adolescentes, fundamentando-se em uma revisão crítica sobre o assunto. Para a revisão do tema foram consultadas as principais bases de dados nacionais e internacionais, entre elas, Medline/Pubmed, Web of Science, SciELO, Lilacs, compreendendo o período de 1975 a 2009. Os descritores e termos MeSH utilizados na busca foram: "sobrepeso", "obesidade", "adolescência", "adolescentes", "atividade física", "ingestão alimentar". Os resultados das pesquisas indicam que as mudanças ocorridas nos padrões alimentares nas últimas décadas, como o aumento do consumo de açúcares simples, alimentos industrializados e ingestão insuficiente de frutas e hortaliças, estão diretamente associadas ao ganho de peso dos adolescentes. Além disso, a redução progressiva da prática de atividade física combinada ao maior tempo dedicado às atividades de baixa intensidade, como assistir televisão, usar computador e jogar videogame, também tem contribuído para o aumento de peso dos jovens. Conclui-se, portanto, que as variáveis relacionadas ao padrão alimentar e de atividade física devem ser priorizadas nas intervenções voltadas para a prevenção da obesidade entre adolescentes.

Estudo randômico da correção cirúrgica do prolapso uterino através de tela sintética de polipropileno tipo I comparando histerectomia versus preservação uterina

OBJETIVO: Comparar os resultados anatômicos pós-operatórios de pacientes portadoras de prolapso uterino tratadas utilizando tela de polipropileno para correção dos defeitos do assoalho pélvico, comparando histerectomia vaginal com a preservação do útero. MÉTODO: Estudo randomizado com 31 mulheres portadoras de prolapso uterino estádio III ou IV (POP-Q) divididas em dois grupos: Grupo HV- 15 mulheres submetidas à histerectomia vaginal e reconstrução da anatomia do assoalho pélvico com tela de polipropileno tipo I (Nazca R-Promedon) e Grupo HP- 16 mulheres mulheres submetidas à reconstrução da anatomia do assoalho pélvico com tela de polipropileno tipo I (Nazca R-Promedon) preservando o útero. Raça, urgência miccional, constipação intestinal, dor sacral, sangramento e tempo de operação foram os parâmetros analisados. RESULTADOS: O tempo de seguimento médio foi de nove meses. Não se observou diferença entre os grupos nas complicações funcionais. O tempo cirúrgico foi 120 minutos para grupo HV versus 58.9 minutos para grupo HP ( p < 0.001 ) e o volume de perda sanguínea intraoperatória foi 120 mL no grupo HV versus 20 mL para grupo HP ( p < 0.001*). A taxa de sucesso objetivo foi 86.67% para grupo HV e 75% para grupo HP (p = 0,667). A taxa de erosão de tela foi 20% (3/15) de extrusão no grupo HV versus 18,75% (3/16) no grupo HP (p = 1,000). CONCLUSÃO: A correção cirúrgica do assoalho pélvico com telas nas portadoras de prolapso uterino apresentaram similaridade quer sendo ela feita com histeropexia quer com histerectomia. Contudo, o tempo cirúrgico e o volume da perda sanguínea foram significantemente maiores no grupo com histerectromia (HV). Operações vaginais com telas são procedimentos efetivos para a correção do prolapso.

Qualidade de luz na biometria e anatomia foliar de plântulas de Cattleya loddigesii L. (Orchidaceae) micropropagadas

A qualidade de luz pode alterar a morfogênese das plantas por meio de uma série de processos mediados por receptores de luz, principalmente na região do vermelho e azul. O objetivo do presente estudo foi verificar alterações anatômicas foliares e características biométricas de Cattleya loddigesii 'Tipo', cultivadas in vitro, sob diferentes malhas coloridas com nível de radiação de 50% de sombreamento. Plântulas oriundas de autopolinização e sementes germinadas in vitro, com aproximadamente 1,0cm de comprimento e com raízes, foram inoculadas em meio WPM e submetidas a diferentes condições de incubação. Testou-se o efeito de sombrites coloridos (vermelho e azul) sobre os frascos cultivados em casa de vegetação (CV) e sala de crescimento (SC), além dos tratamentos, nos dois ambientes, sem utilização das telas coloridas. A avaliação foi efetuada 180 dias após inoculação. Com os resultados obtidos, observou-se que o ambiente de cultivo promove alterações anatômicas e biométricas em plântulas de Cattleya loddigesii 'Tipo' micropropagadas. As alterações promovidas pelo cultivo em luz natural evidenciam maior capacidade fotossintética, por meio de maior diferenciação dos tecidos clorofilianos, promovendo uma superfície foliar anatomicamente adaptada à fase de aclimatização.

Cortisol plasmático como indicador de estresse em colopexias laparoscópicas com implante de tela de polipropileno em cães

The realization of conventional surgical procedures, even using the recommended doses of analgesics drugs, generally are associated with a long recovery period, post-surgical trauma, stress and pain in animals. That can vary according with the procedure, extension and time of the surgery. Considering the increased interest in procedures that minimize surgical stress and the recovery period after the surgical procedure in dogs, this present work was developed to evaluate a new technique of laparoscopic colopexy with the alterations of cortisol levels, heart rate and respiratory frequencies in dogs. For this study, nine female dogs were submitted to a colopexy. Blood samples and data of heart rate and respiratory frequency were sampled in intervals of 10min. from the preoperative period until the end of the procedure. After, these parameters were assessed every three hours for 12 hours. Cortisol levels were measured using an ELISA Kit for cortisol. Results were analyzed by ANOVA and comparisons were made using Tukey's test. Significance levels was set at p <= 0.05. The increase of the heart rate, respiratory frequency and cortisol levels were mainly observed in the period after shaving and after the end of the anesthesia. Values were kept stable during all the surgery, and coming to the basal conditions after nine hours in the post-operative period. The laparoscopic colopexy is a stress-associated surgery, but it produces lower increasing of cortisol levels returning to normal in 9 hours after the surgery.

Skewness, splitting number and vertex deletion of some toroidal meshes

The skewness sk(G) of a graph G = (V, E) is the smallest integer sk(G) >= 0 such that a planar graph can be obtained from G by the removal of sk(C) edges. The splitting number sp(G) of C is the smallest integer sp(G) >= 0 such that a planar graph can be obtained from G by sp(G) vertex splitting operations. The vertex deletion vd(G) of G is the smallest integer vd(G) >= 0 such that a planar graph can be obtained from G by the removal of vd(G) vertices. Regular toroidal meshes are popular topologies for the connection networks of SIMD parallel machines. The best known of these meshes is the rectangular toroidal mesh C(m) x C(n) for which is known the skewness, the splitting number and the vertex deletion. In this work we consider two related families: a triangulation Tc(m) x c(n) of C(m) x C(n) in the torus, and an hexagonal mesh Hc(m) x c(n), the dual of Tc(m) x c(n) in the torus. It is established that sp(Tc(m) x c(n)) = vd(Tc(m) x c(n) = sk(Hc(m) x c(n)) = sp(Hc(m) x c(n)) = vd(Hc(m) x c(n)) = min{m, n} and that sk(Tc(m) x c(n)) = 2 min {m, n}.

Toughened ZrO2 ceramics sintered with a La2O3-rich glass as additive

In this study, the influence of the glass addition and sintering parameters on the densification and mechanical properties of tetragonal zirconia polycrystals (3Y-TZP) ceramics were evaluated. High-purity tetragonal ZrO2 powder and La2O3-rich glass were used as starting powders. Two compositions based on ZrO2 and containing 5wt.% and 10wt.% of La2O3-rich glass were studied in this work. The starting powders were mixed/milled by planetary milling, dried at 90 degrees C for 24 h, sieved through a 60 mesh screen and uniaxially cold pressed under 80 MPa. The samples were sintered in air at 1200 degrees C, 1300 degrees C, 1400 degrees C for 60 min and at 1450 degrees C for 120 min, with heating and cooling rates of 10 degrees C/min. Sintered samples were characterized by relative density, X-ray diffraction (XRD) and scanningelectron microscopy (SEM). Hardness and fracture toughness were obtained by Vickers indentation method. Dense sintered samples were obtained for all conditions. Furthermore, only tetragonal-ZrO2 was identified as crystalline phase in sintered samples, independently of the conditions studied. Samples sintered at 1300 degrees C for 60 min presented the optimal mechanical properties with hardness and fracture toughness values near to 12 GPa and 8.5 MPa m(1/2) respectively. (c) 2007 Elsevier B.V, All rights reserved.

A simple method for non-linear analysis of steel fiber reinforced concrete

This paper proposes a physical non-linear formulation to deal with steel fiber reinforced concrete by the finite element method. The proposed formulation allows the consideration of short or long fibers placed arbitrarily inside a continuum domain (matrix). The most important feature of the formulation is that no additional degree of freedom is introduced in the pre-existent finite element numerical system to consider any distribution or quantity of fiber inclusions. In other words, the size of the system of equations used to solve a non-reinforced medium is the same as the one used to solve the reinforced counterpart. Another important characteristic of the formulation is the reduced work required by the user to introduce reinforcements, avoiding ""rebar"" elements, node by node geometrical definitions or even complex mesh generation. Bounded connection between long fibers and continuum is considered, for short fibers a simplified approach is proposed to consider splitting. Non-associative plasticity is adopted for the continuum and one dimensional plasticity is adopted to model fibers. Examples are presented in order to show the capabilities of the formulation.

Analyzing static three-dimensional elastic domains with a new infinite boundary element formulation

A new two-dimensionally mapped infinite boundary element (IBE) is presented. The formulation is based on a triangular boundary element (BE) with linear shape functions instead of the quadrilateral IBEs usually found in the literature. The infinite solids analyzed are assumed to be three-dimensional, linear-elastic and isotropic, and Kelvin fundamental solutions are employed. One advantage of the proposed formulation over quadratic or higher order elements is that no additional degrees of freedom are added to the original BE mesh by the presence of the IBEs. Thus, the IBEs allow the mesh to be reduced without compromising the accuracy of the result. Two examples are presented, in which the numerical results show good agreement with authors using quadrilateral IBEs and analytical solutions. (C) 2010 Elsevier Ltd. All rights reserved.

A simple way to introduce fibers into FEM models

This communication proposes a simple way to introduce fibers into finite element modelling. This is a promising formulation to deal with fiber-reinforced composites by the finite element method (FEM), as it allows the consideration of short or long fibers placed arbitrarily inside a continuum domain (matrix). The most important feature of the formulation is that no additional degree of freedom is introduced into the pre-existent finite element numerical system to consider any distribution of fiber inclusions. In other words, the size of the system of equations used to solve a non-reinforced medium is the same as the one used to solve the reinforced counterpart. Another important characteristic is the reduced work required by the user to introduce fibers, avoiding `rebar` elements, node-by-node geometrical definitions or even complex mesh generation. An additional characteristic of the technique is the possibility of representing unbounded stresses at the end of fibers using a finite number of degrees of freedom. Further studies are required for non-linear applications in which localization may occur. Along the text the linear formulation is presented and the bounded connection between fibers and continuum is considered. Four examples are presented, including non-linear analysis, to validate and show the capabilities of the formulation. Copyright (c) 2007 John Wiley & Sons, Ltd.

A numerical model for the description of the nonlinear behaviour of multi-leaf masonry walls

A nonlinear finite element model was developed to simulate the nonlinear response of three-leaf masonry specimens, which were subjected to laboratory tests with the aim of investigating the mechanical behaviour of multiple-leaf stone masonry walls up to failure. The specimens consisted of two external leaves made of stone bricks and mortar joints, and an internal leaf in mortar and stone aggregate. Different loading conditions, typologies of the collar joints, and stone types were taken into account. The constitutive law implemented in the model is characterized by a damage tensor, which allows the damage-induced anisotropy accompanying the cracking process to be described. To follow the post-peak behaviour of the specimens with sufficient accuracy it was necessary to make the damage model non-local, to avoid mesh-dependency effects related to the strain-softening behaviour of the material. Comparisons between the predicted and measured failure loads are quite satisfactory in most of the studied cases. (c) 2007 Elsevier Ltd. All rights reserved.

A STUDY OF PENALTY FORMULATIONS USED IN THE NUMERICAL APPROXIMATION OF A RADIALLY SYMMETRIC ELASTICITY PROBLEM

We consider a class of two-dimensional problems in classical linear elasticity for which material overlapping occurs in the absence of singularities. Of course, material overlapping is not physically realistic, and one possible way to prevent it uses a constrained minimization theory. In this theory, a minimization problem consists of minimizing the total potential energy of a linear elastic body subject to the constraint that the deformation field must be locally invertible. Here, we use an interior and an exterior penalty formulation of the minimization problem together with both a standard finite element method and classical nonlinear programming techniques to compute the minimizers. We compare both formulations by solving a plane problem numerically in the context of the constrained minimization theory. The problem has a closed-form solution, which is used to validate the numerical results. This solution is regular everywhere, including the boundary. In particular, we show numerical results which indicate that, for a fixed finite element mesh, the sequences of numerical solutions obtained with both the interior and the exterior penalty formulations converge to the same limit function as the penalization is enforced. This limit function yields an approximate deformation field to the plane problem that is locally invertible at all points in the domain. As the mesh is refined, this field converges to the exact solution of the plane problem.