Field and Laboratory Evaluation of Precast Concrete Bridges, TR-440, 2001

Recent data compiled by the National Bridge Inventory revealed 29% of Iowa's approximate 24,600 bridges were either structurally deficient or functionally obsolete. This large number of deficient bridges and the high cost of needed repairs create unique problems for Iowa and many other states. The research objective of this project was to determine the load capacity of a particular type of deteriorating bridge – the precast concrete deck bridge – which is commonly found on Iowa's secondary roads. The number of these precast concrete structures requiring load postings and/or replacement can be significantly reduced if the deteriorated structures are found to have adequate load capacity or can be reliably evaluated. Approximately 600 precast concrete deck bridges (PCDBs) exist in Iowa. A typical PCDB span is 19 to 36 ft long and consists of eight to ten simply supported precast panels. Bolts and either a pipe shear key or a grouted shear key are used to join adjacent panels. The panels resemble a steel channel in cross-section; the web is orientated horizontally and forms the roadway deck and the legs act as shallow beams. The primary longitudinal reinforcing steel bundled in each of the legs frequently corrodes and causes longitudinal cracks in the concrete and spalling. The research team performed service load tests on four deteriorated PCDBs; two with shear keys in place and two without. Conventional strain gages were used to measure strains in both the steel and concrete, and transducers were used to measure vertical deflections. Based on the field results, it was determined that these bridges have sufficient lateral load distribution and adequate strength when shear keys are properly installed between adjacent panels. The measured lateral load distribution factors are larger than AASHTO values when shear keys were not installed. Since some of the reinforcement had hooks, deterioration of the reinforcement has a minimal affect on the service level performance of the bridges when there is minimal loss of cross-sectional area. Laboratory tests were performed on the PCDB panels obtained from three bridge replacement projects. Twelve deteriorated panels were loaded to failure in a four point bending arrangement. Although the panels had significant deflections prior to failure, the experimental capacity of eleven panels exceeded the theoretical capacity. Experimental capacity of the twelfth panel, an extremely distressed panel, was only slightly below the theoretical capacity. Service tests and an ultimate strength test were performed on a laboratory bridge model consisting of four joined panels to determine the effect of various shear connection configurations. These data were used to validate a PCDB finite element model that can provide more accurate live load distribution factors for use in rating calculations. Finally, a strengthening system was developed and tested for use in situations where one or more panels of an existing PCDB need strengthening.

Pediatric drug-related problems: a multicenter study in four French-speaking countries.

BACKGROUND: Pediatric intensive care patients represent a population at high risk for drug-related problems. There are few studies that compare the activity of clinical pharmacists between countries. OBJECTIVE: To describe the drug-related problems identified and interventions by four pharmacists in a pediatric cardiac and intensive care unit. SETTING: Four pediatric centers in France, Quebec, Switzerland and Belgium. METHOD: This was a six-month multicenter, descriptive and prospective study conducted from August 1, 2009 to January 31, 2010. Drug-related problems and clinical interventions were compiled from four pediatric centers in France, Quebec, Switzerland and Belgium. Data on patients, drugs, intervention, documentation, approval and estimated impact were compiled. MAIN OUTCOME MEASURE: Number and type of drug-related problems encountered in a large pediatric inpatient population. RESULTS: A total of 996 interventions were recorded: 238 (24 %) in France, 278 (28 %) in Quebec, 351 (35 %) in Switzerland and 129 (13 %) in Belgium. These interventions targeted 270 patients (median 21 months old, 53 % male): 88 (33 %) in France, 56 (21 %) in Quebec, 57 (21 %) in Switzerland and 69 (26 %) in Belgium. The main drug-related problems were inappropriate administration technique (29 %), untreated indication (25 %) and supra-therapeutic dose (11 %). The pharmacists' interventions were mostly optimizing the mode of administration (22 %), dose adjustment (20 %) and therapeutic monitoring (16 %). The two major drug classes that led to interventions were anti-infectives for systemic use (23 %) and digestive system and metabolism drugs (22 %). Interventions mainly involved residents and all clinical staff (21 %). Among the 878 (88 %) proposed interventions requiring physician approval, 860 (98 %) were accepted. CONCLUSION: This descriptive study illustrates drug-related problems and the ability of clinical pharmacists to identify and resolve them in pediatric intensive care units in four French-speaking countries.

Development of a Subgrade Drainage Model for Unpaved Roads, TR-654, 2015

With over 68 thousand miles of gravel roads in Iowa and the importance of these roads within the farm-to-market transportation system, proper water management becomes critical for maintaining the integrity of the roadway materials. However, the build-up of water within the aggregate subbase can lead to frost boils and ultimately potholes forming at the road surface. The aggregate subbase and subgrade soils under these gravel roads are produced with material opportunistically chosen from local sources near the site and, many times, the compositions of these sublayers are far from ideal in terms of proper water drainage with the full effects of this shortcut not being fully understood. The primary objective of this project was to provide a physically-based model for evaluating the drainability of potential subbase and subgrade materials for gravel roads in Iowa. The Richards equation provided the appropriate framework to study the transient unsaturated flow that usually occurs through the subbase and subgrade of a gravel road. From which, we identified that the saturated hydraulic conductivity, Ks, was a key parameter driving the time to drain of subgrade soils found in Iowa, thus being a good proxy variable for accessing roadway drainability. Using Ks, derived from soil texture, we were able to identify potential problem areas in terms of roadway drainage . It was found that there is a threshold for Ks of 15 cm/day that determines if the roadway will drain efficiently, based on the requirement that the time to drain, Td, the surface roadway layer does not exceed a 2-hr limit. Two of the three highest abundant textures (loam and silty clay loam), which cover nearly 60% of the state of Iowa, were found to have average Td values greater than the 2-hr limit. With such a large percentage of the state at risk for the formation of boils due to the soil with relatively low saturated hydraulic conductivity values, it seems pertinent that we propose alternative design and/or maintenance practices to limit the expensive repair work in Iowa. The addition of drain tiles or French mattresses my help address drainage problems. However, before pursuing this recommendation, a comprehensive cost-benefit analysis is needed.

Factores de riesgo de conducta violenta intrainstitucional en internos penitenciarios

Este estudio tiene por objeto la determinación de la prevalencia y las correlaciones asociadas a las infracciones disciplinarias violentas y potencialmente violentas de 11 centros penitenciarios de Cataluña. Para alcanzar este objetivo el presente estudio prospectivo, basado en datos oficiales, examina la relación entre variables sociodemográficas, criminales, penitenciarias y psicológicas de una muestra de 7517 internos/as durante un período de seguimiento de 2 años. Los resultados obtenidos indican que ser más joven, estar en situación de prisión preventiva en el caso de las mujeres, haber presentado conducta violenta o antisocial anteriormente, tanto en la comunidad como en el ámbito penitenciario, responder de una manera poco exitosa a los tratamientos recientes o mostrar problemas en el consumo de alcohol o drogas y las actitudes procriminales son factores de gran potencia en la predicción de infracciones disciplinarias. Para concluir, cabe mencionar que investigaciones adicionales en otras áreas geográficas y la consideración de variables situacionales son necesarias para corroborar los resultados aquí obtenidos. También se discuten algunas implicaciones para políticas penitenciarias y para futuras líneas de investigación.

Local optima networks of hard combinatorial landscapes

Combinatorial optimization involves finding an optimal solution in a finite set of options; many everyday life problems are of this kind. However, the number of options grows exponentially with the size of the problem, such that an exhaustive search for the best solution is practically infeasible beyond a certain problem size. When efficient algorithms are not available, a practical approach to obtain an approximate solution to the problem at hand, is to start with an educated guess and gradually refine it until we have a good-enough solution. Roughly speaking, this is how local search heuristics work. These stochastic algorithms navigate the problem search space by iteratively turning the current solution into new candidate solutions, guiding the search towards better solutions. The search performance, therefore, depends on structural aspects of the search space, which in turn depend on the move operator being used to modify solutions. A common way to characterize the search space of a problem is through the study of its fitness landscape, a mathematical object comprising the space of all possible solutions, their value with respect to the optimization objective, and a relationship of neighborhood defined by the move operator. The landscape metaphor is used to explain the search dynamics as a sort of potential function. The concept is indeed similar to that of potential energy surfaces in physical chemistry. Borrowing ideas from that field, we propose to extend to combinatorial landscapes the notion of the inherent network formed by energy minima in energy landscapes. In our case, energy minima are the local optima of the combinatorial problem, and we explore several definitions for the network edges. At first, we perform an exhaustive sampling of local optima basins of attraction, and define weighted transitions between basins by accounting for all the possible ways of crossing the basins frontier via one random move. Then, we reduce the computational burden by only counting the chances of escaping a given basin via random kick moves that start at the local optimum. Finally, we approximate network edges from the search trajectory of simple search heuristics, mining the frequency and inter-arrival time with which the heuristic visits local optima. Through these methodologies, we build a weighted directed graph that provides a synthetic view of the whole landscape, and that we can characterize using the tools of complex networks science. We argue that the network characterization can advance our understanding of the structural and dynamical properties of hard combinatorial landscapes. We apply our approach to prototypical problems such as the Quadratic Assignment Problem, the NK model of rugged landscapes, and the Permutation Flow-shop Scheduling Problem. We show that some network metrics can differentiate problem classes, correlate with problem non-linearity, and predict problem hardness as measured from the performances of trajectory-based local search heuristics.

Characterization of board impurities with a Raman device

Erilaisia epäpuhtauksia kulkeutuu paperinvalmistusprosessiin ja monenlaisia saostumia muodostuu paperinvalmistuksen prosesseissa. Epäpuhtaudet voivat aiheuttaa prosessiongelmia sekä alentaa tuotteen laatua. Epäpuhtauksien alkuperän ja koostumuksen selvittäminen edellyttää usein erilaisten analyysimenetelmien käyttöä. Epäpuhtauksien luokittelu on useasti välttämätöntä ennen tarkempaa kemiallista analyysia. Paperinvalmistuksen epäpuhtauksien kvalitatiiviseen luokitteluun on yleisimmin käytetty mikroskopian, IR-spektroskopian ja analyyttisen pyrolyysin menetelmiä. Raman spektroskopia on harvinaisempi menetelmä paperiteollisuuden tutkimuksessa. Raman instrumenttien kehittyminen on ollut voimakasta viimeisen vuosikymmenen aikana. Raman spektroskopia onkin osoittanut mandollisuutensa polymeerien, lääketeollisuuden ja polttoaineteollisuuden tutkimuksissa. Tässä työssä tutkittiin erään elintarvikepakkauskartongin epäpuhtauksia Raman spektroskoopilla. Työn tavoitteena oli selvittää Raman analyysin käyttökelpoisuutta kartongin epäpuhtauksien online-luokittelussa. Tutkimukset suoritettiin Spectracoden RP-1 Raman instrumentilla. Tutkimukset osoittivat, että näytteen fluoresenssi ja näytteen hajoaminen asettavat rajoituksia epäpuhtauksien Raman analyysille. Epäpuhtauksien online-tunnistaminen toimii käytettäessä suuria lasertehoja ja säteilytysaikoja. Näytteiden laserherkkyys ja fluoresenssi rajoittavat kuitenkin suurien laiteparametrien käyttöä. Laiteparametrien pienentäminen johti mittauksien signaali-kohina suhteen alenemiseen, mikä puolestaan aiheutti online-tunnistuksen toimimattomuuden.

Problems of allometric scaling analysis: examples from mammalian reproductive biology.

Biological scaling analyses employing the widely used bivariate allometric model are beset by at least four interacting problems: (1) choice of an appropriate best-fit line with due attention to the influence of outliers; (2) objective recognition of divergent subsets in the data (allometric grades); (3) potential restrictions on statistical independence resulting from phylogenetic inertia; and (4) the need for extreme caution in inferring causation from correlation. A new non-parametric line-fitting technique has been developed that eliminates requirements for normality of distribution, greatly reduces the influence of outliers and permits objective recognition of grade shifts in substantial datasets. This technique is applied in scaling analyses of mammalian gestation periods and of neonatal body mass in primates. These analyses feed into a re-examination, conducted with partial correlation analysis, of the maternal energy hypothesis relating to mammalian brain evolution, which suggests links between body size and brain size in neonates and adults, gestation period and basal metabolic rate. Much has been made of the potential problem of phylogenetic inertia as a confounding factor in scaling analyses. However, this problem may be less severe than suspected earlier because nested analyses of variance conducted on residual variation (rather than on raw values) reveals that there is considerable variance at low taxonomic levels. In fact, limited divergence in body size between closely related species is one of the prime examples of phylogenetic inertia. One common approach to eliminating perceived problems of phylogenetic inertia in allometric analyses has been calculation of 'independent contrast values'. It is demonstrated that the reasoning behind this approach is flawed in several ways. Calculation of contrast values for closely related species of similar body size is, in fact, highly questionable, particularly when there are major deviations from the best-fit line for the scaling relationship under scrutiny.

Comparaison objective de systèmes d'imagerie conventionnelle et numérique en mammographie

L'objectif de ce travail est le développement d'une méthode de caractérisation objective de la qualité d'image s'appliquant à des systèmes de mammographie analogique, utilisant un couple écran-film comme détecteur, et numérique, basé sur une technologie semi-conductrice, ceci en vue de la comparaison de leurs performances. La méthode développée tient compte de la gamme dynamique du détecteur, de la détectabilité de structures de haut contraste, simulant des microcalcifications, et de structures de bas contraste, simulant des opacités (nodules tumoraux). La méthode prend également en considération le processus de visualisation de l'image, ainsi que la réponse de l'observateur. Pour réaliser ceci, un objet-test ayant des propriétés proches de celles d'un sein comprimé, composé de différents matériaux équivalents aux tissus, allant du glandulaire à l'adipeux, et comprenant des zones permettant la simulation de structures de haut et bas contraste, ainsi que la mesure de la résolution et celle du bruit, a été développé et testé. L'intégration du processus de visualisation a été réalisée en utilisant une caméra CCD mesurant directement les paramètres de qualité d'image, à partir de l'image de l'objet-test, dans une grandeur physique commune au système numérique et analogique, à savoir la luminance arrivant sur l'oeil de l'observateur. L'utilisation d'une grandeur synthétique intégrant dans un même temps, le contraste, le bruit et la résolution rend possible une comparaison objective entre les deux systèmes de mammographie. Un modèle mathématique, simulant la réponse d'un observateur et intégrant les paramètres de base de qualité d'image, a été utilisé pour calculer la détectabilité de structures de haut et bas contraste en fonction du type de tissu sur lequel celles-ci se trouvent. Les résultats obtenus montrent qu'à dose égale la détectabilité des structures est significativement plus élevée avec le système de mammographie numérique qu'avec le système analogique. Ceci est principalement lié au fait que le bruit du système numérique est plus faible que celui du système analogique. Les résultats montrent également que la méthodologie, visant à comparer des systèmes d'imagerie numérique et analogique en utilisant un objet-test à large gamme dynamique ainsi qu'une caméra, peut être appliquée à d'autres modalités radiologiques, ainsi qu'à une démarche d'optimisation des conditions de lecture des images.<br/><br/>The goal of this work was to develop a method to objectively compare the performance of a digital and a screen-film mammography system in terms of image quality and patient dose. We propose a method that takes into account the dynamic range of the image detector and the detection of high contrast (for microcalcifications) and low contrast (for masses or tumoral nodules) structures. The method also addresses the problems of image visualization and the observer response. A test object, designed to represent a compressed breast, was constructed from various tissue equivalent materials ranging from purely adipose to purely glandular composition. Different areas within the test object permitted the evaluation of low and high contrast detection, spatial resolution, and image noise. All the images (digital and conventional) were captured using a CCD camera to include the visualization process in the image quality assessment. In this way the luminance reaching the viewer?s eyes can be controlled for both kinds of images. A global quantity describing image contrast, spatial resolution and noise, and expressed in terms of luminance at the camera, can then be used to compare the two technologies objectively. The quantity used was a mathematical model observer that calculates the detectability of high and low contrast structures as a function of the background tissue. Our results show that for a given patient dose, the detection of high and low contrast structures is significantly better for the digital system than for the conventional screen-film system studied. This is mainly because the image noise is lower for the digital system than for the screen-film detector. The method of using a test object with a large dynamic range combined with a camera to compare conventional and digital imaging modalities can be applied to other radiological imaging techniques. In particular it could be used to optimize the process of radiographic film reading.

Artificial evolution on network structures : how time and space influence dynamics

Abstract The main objective of this work is to show how the choice of the temporal dimension and of the spatial structure of the population influences an artificial evolutionary process. In the field of Artificial Evolution we can observe a common trend in synchronously evolv¬ing panmictic populations, i.e., populations in which any individual can be recombined with any other individual. Already in the '90s, the works of Spiessens and Manderick, Sarma and De Jong, and Gorges-Schleuter have pointed out that, if a population is struc¬tured according to a mono- or bi-dimensional regular lattice, the evolutionary process shows a different dynamic with respect to the panmictic case. In particular, Sarma and De Jong have studied the selection pressure (i.e., the diffusion of a best individual when the only selection operator is active) induced by a regular bi-dimensional structure of the population, proposing a logistic modeling of the selection pressure curves. This model supposes that the diffusion of a best individual in a population follows an exponential law. We show that such a model is inadequate to describe the process, since the growth speed must be quadratic or sub-quadratic in the case of a bi-dimensional regular lattice. New linear and sub-quadratic models are proposed for modeling the selection pressure curves in, respectively, mono- and bi-dimensional regu¬lar structures. These models are extended to describe the process when asynchronous evolutions are employed. Different dynamics of the populations imply different search strategies of the resulting algorithm, when the evolutionary process is used to solve optimisation problems. A benchmark of both discrete and continuous test problems is used to study the search characteristics of the different topologies and updates of the populations. In the last decade, the pioneering studies of Watts and Strogatz have shown that most real networks, both in the biological and sociological worlds as well as in man-made structures, have mathematical properties that set them apart from regular and random structures. In particular, they introduced the concepts of small-world graphs, and they showed that this new family of structures has interesting computing capabilities. Populations structured according to these new topologies are proposed, and their evolutionary dynamics are studied and modeled. We also propose asynchronous evolutions for these structures, and the resulting evolutionary behaviors are investigated. Many man-made networks have grown, and are still growing incrementally, and explanations have been proposed for their actual shape, such as Albert and Barabasi's preferential attachment growth rule. However, many actual networks seem to have undergone some kind of Darwinian variation and selection. Thus, how these networks might have come to be selected is an interesting yet unanswered question. In the last part of this work, we show how a simple evolutionary algorithm can enable the emrgence o these kinds of structures for two prototypical problems of the automata networks world, the majority classification and the synchronisation problems. Synopsis L'objectif principal de ce travail est de montrer l'influence du choix de la dimension temporelle et de la structure spatiale d'une population sur un processus évolutionnaire artificiel. Dans le domaine de l'Evolution Artificielle on peut observer une tendence à évoluer d'une façon synchrone des populations panmictiques, où chaque individu peut être récombiné avec tout autre individu dans la population. Déjà dans les année '90, Spiessens et Manderick, Sarma et De Jong, et Gorges-Schleuter ont observé que, si une population possède une structure régulière mono- ou bi-dimensionnelle, le processus évolutionnaire montre une dynamique différente de celle d'une population panmictique. En particulier, Sarma et De Jong ont étudié la pression de sélection (c-à-d la diffusion d'un individu optimal quand seul l'opérateur de sélection est actif) induite par une structure régulière bi-dimensionnelle de la population, proposant une modélisation logistique des courbes de pression de sélection. Ce modèle suppose que la diffusion d'un individu optimal suit une loi exponentielle. On montre que ce modèle est inadéquat pour décrire ce phénomène, étant donné que la vitesse de croissance doit obéir à une loi quadratique ou sous-quadratique dans le cas d'une structure régulière bi-dimensionnelle. De nouveaux modèles linéaires et sous-quadratique sont proposés pour des structures mono- et bi-dimensionnelles. Ces modèles sont étendus pour décrire des processus évolutionnaires asynchrones. Différentes dynamiques de la population impliquent strategies différentes de recherche de l'algorithme résultant lorsque le processus évolutionnaire est utilisé pour résoudre des problèmes d'optimisation. Un ensemble de problèmes discrets et continus est utilisé pour étudier les charactéristiques de recherche des différentes topologies et mises à jour des populations. Ces dernières années, les études de Watts et Strogatz ont montré que beaucoup de réseaux, aussi bien dans les mondes biologiques et sociologiques que dans les structures produites par l'homme, ont des propriétés mathématiques qui les séparent à la fois des structures régulières et des structures aléatoires. En particulier, ils ont introduit la notion de graphe sm,all-world et ont montré que cette nouvelle famille de structures possède des intéressantes propriétés dynamiques. Des populations ayant ces nouvelles topologies sont proposés, et leurs dynamiques évolutionnaires sont étudiées et modélisées. Pour des populations ayant ces structures, des méthodes d'évolution asynchrone sont proposées, et la dynamique résultante est étudiée. Beaucoup de réseaux produits par l'homme se sont formés d'une façon incrémentale, et des explications pour leur forme actuelle ont été proposées, comme le preferential attachment de Albert et Barabàsi. Toutefois, beaucoup de réseaux existants doivent être le produit d'un processus de variation et sélection darwiniennes. Ainsi, la façon dont ces structures ont pu être sélectionnées est une question intéressante restée sans réponse. Dans la dernière partie de ce travail, on montre comment un simple processus évolutif artificiel permet à ce type de topologies d'émerger dans le cas de deux problèmes prototypiques des réseaux d'automates, les tâches de densité et de synchronisation.

Le pergélisol dans les terrains sédimentaires à forte déclivité: distribution, régime thermique et instabilités

Résumé: Dans le contexte d'un climat de plus en plus chaud, la localisation du pergélisol dans les terrains sédimentaires à forte déclivité et l'évaluation des mouvements de terrain qui y ont cours s'avèrent primordiales. S'insérant dans cette problématique, ce travail de thèse s'articule autour de deux axes de recherche différents. D'un point de vue statique, cette recherche propose une étude de la distribution et des caractéristiques du pergélisol dans les éboulis de la zone périglaciaire alpine. D'un point de vue dynamique, une analyse de l'influence des caractéristiques du pergélisol (teneur en glace, température du pergélisol, etc.) et des variations des températures de l'air et du sol sur les vitesses de fluage des corps sédimentaires gelés est effectuée. Afin de répondre à ce double objectif, l'approche "terrain" a été privilégiée. Pour déterminer la répartition et les caractéristiques du pergélisol, les méthodes traditionnelles de prospection du pergélisol ont été utilisées, à savoir la mesure de la température du sol à la base du manteau neigeux (BTS), la mesure de la température du sol en continu ainsi que la méthode géoélectrique. Les mouvements de terrain ont pour leur part été mesurés à l'aide d'un GPS différentiel. L'étude de la distribution du pergélisol a été effectuée dans une quinzaine d'éboulis situés dans les régions du Mont Gelé (Verbier-Nendaz) et d'Arolla principalement. Dans la plupart des cas, un pergélisol a pu être mis en évidence dans la partie inférieure des accumulations sédimentaires, alors que la partie médiane des éboulis n'est, le plus souvent, pas gelée. Si cette absence de pergélisol se prolonge parfois dans les portions sommitales des pentes, les mesures réalisées montrent que dans d'autres cas des sédiments gelés y sont à nouveau présents. Les résistivités électriques mesurées dans les portions gelées des éboulis étudiés sont dans la plupart des cas nettement inférieures à celles mesurées sur les glaciers rocheux. Des études préalables ont montré que des circulations d'air internes sont responsables de l'anomalie thermique négative et, lorsqu'il existe, du pergélisol que l'on trouve dans la partie inférieure d'éboulis situés plus de 1000 m plus bas que la limite inférieure régionale du pergélisol discontinu. L'étude de quatre sites de basse altitude (1400-1900 m), et notamment l'équipement du site de Dreveneuse (Préalpes Valaisannes) avec deux forages, des capteurs de température de surface et un anémomètre a permis de vérifier et de préciser le mécanisme de ventilation actif au sein des éboulis froids de basse altitude. Ce mécanisme fonctionne de la manière suivante: en hiver, l'air contenu dans l'éboulis, plus chaud et plus léger que l'air extérieur, monte à l'intérieur de l'accumulation sédimentaire et est expulsé dans ses parties sommitales. Cet effet de cheminée provoque une aspiration d'air froid à l'intérieur de la partie inférieure de l'éboulis, causant ainsi un sur-refroidissement marqué du terrain. En été, le mécanisme s'inverse, l'éboulis étant plus froid que l'air environnant. De l'air froid est alors expulsé au bas de la pente. Une ventilation ascendante hivernale a pu être mise en évidence dans certains des éboulis de haute altitude étudiés. Elle est probablement en grande partie responsable de la configuration particulière des zones gelées observées. Même si l'existence d'un effet de cheminée n'a pu être démontrée dans tous les cas, du fait notamment de la glace interstitielle qui entrave le cheminement de l'air, des indices laissant présager son possible fonctionnement existent dans la quasi totalité des éboulis étudiés. L'absence de pergélisol à des altitudes qui lui sont favorables pourrait en tous les cas s'expliquer par un réchauffement du terrain lié à des expulsions d'air relativement chaud. L'étude des mouvements de terrain a été effectuée sur une dizaine de sites, principalement sur des glaciers rocheux, mais également sur une moraine de poussée et - II - Résumé ? abstract quelques éboulis. Plusieurs glaciers rocheux présentent des formes de déstabilisation récente (niches d'arrachement, blocs basculés, apparition de la matrice fine à la surface, etc.), ce qui témoigne d'une récente accélération des vitesses de déplacement. Ce phénomène, qui semble général à l'échelle alpine, est probablement à mettre sur le compte du réchauffement du pergélisol depuis une vingtaine d'années. Les vitesses mesurées sur ces formations sont souvent plus élevées que les valeurs habituellement proposées dans la littérature. On note par ailleurs une forte variabilité inter-annuelle des vitesses, qui semblent dépendre de la variation de la température moyenne annuelle de surface. Abstract: In the context of a warmer climate, the localisation of permafrost in steep sedimentary terrain and the measurement of terrain movements that occur in these areas is of great importance. With respect to these problems, this PhD thesis follows two different research axes. From a static point of view, the research presents a study of the permafrost distribution and characteristics in the talus slopes of the alpine periglacial belt. From a dynamic point of view, an analysis of the influence of the permafrost characteristics (ice content, permafrost temperature, etc.) and air and soil temperature variations on the creep velocities of frozen sedimentary bodies is carried out. In order to attain this double objective, the "field" approach was favoured. To determine the distribution and the characteristics of permafrost, the traditional methods of permafrost prospecting were used, i.e. ground surface temperature measurements at the base of the snow cover (BTS), year-round ground temperature measurements and DC-resistivity prospecting. The terrain movements were measured using a differential GPS. The permafrost distribution study was carried out on 15 talus slopes located mainly in the Mont Gelé (Verbier-Nendaz) and Arolla areas (Swiss Alps). In most cases, permafrost was found in the lower part of the talus slope, whereas the medium part was free of ice. In some cases, the upper part of the talus is also free of permafrost, whereas in other cases permafrost is present. Electrical resistivities measured in the frozen parts of the studied talus are in most cases clearly lower than those measured on rock glaciers. Former studies have shown that internal air circulation is responsible for the negative thermal anomaly and, when it exists, the permafrost present in the lower part of talus slopes located more than 1000 m below the regional lower limit of discontinuous permafrost. The study of four low-altitude talus slopes (1400-1900 m), and notably the equipment of Dreveneuse field site (Valais Prealps) with two boreholes, surface temperature sensors and an anemometer permitted to verify and to detail the ventilation mechanism active in low altitude talus slopes. This mechanism works in the following way: in winter, the air contained in the block accumulation is warmer and lighter than the surrounding air and therefore moves upward in the talus and is expelled in its upper part. This chimney effect induces an aspiration of cold air in the interior of the lower part of talus, that causes a strong overcooling of the ground. In summer, the mechanism is reversed because the talus slope is colder than the surrounding air. Cold air is then expelled in the lower part of the slope. Evidence of ascending ventilation in wintertime could also be found in some of the studied high-altitude talus slopes. It is probably mainly responsible for the particular configuration of the observed frozen areas. Even if the existence of a chimney effect could not be demonstrated in all cases, notably because of interstitial ice that obstructs Résumé ? abstract - III - the air circulation, indices of its presence exist in nearly all the studied talus. The absence of permafrost at altitudes favourable to its presence could be explained, for example, by the terrain warming caused by expulsion of relatively warm air. Terrain movements were measured at about ten sites, mainly on rock glaciers, but also on a push moraine and some talus slopes. Field observations reveal that many rock glaciers display recent destabilization features (landslide scars, tilted blocks, presence of fine grained sediments at the surface, etc.) that indicate a probable recent acceleration of the creep velocities. This phenomenon, which seems to be widespread at the alpine scale, is probably linked to the permafrost warming during the last decades. The measured velocities are often higher than values usually proposed in the literature. In addition, strong inter-annual variations of the velocities were observed, which seems to depend on the mean annual ground temperature variations.

R&D Performance Analysis: Case Studies on the Challenges and Promotion of the Evaluation and Measurement of R&D

Due to the intense international competition, demanding, and sophisticated customers, and diverse transforming technological change, organizations need to renew their products and services by allocating resources on research and development (R&D). Managing R&D is complex, but vital for many organizations to survive in the dynamic, turbulent environment. Thus, the increased interest among decision-makers towards finding the right performance measures for R&D is understandable. The measures or evaluation methods of R&D performance can be utilized for multiple purposes; for strategic control, for justifying the existence of R&D, for providing information and improving activities, as well as for the purposes of motivating and benchmarking. The earlier research in the field of R&D performance analysis has generally focused on either the activities and considerable factors and dimensions - e.g. strategic perspectives, purposes of measurement, levels of analysis, types of R&D or phases of R&D process - prior to the selection of R&Dperformance measures, or on proposed principles or actual implementation of theselection or design processes of R&D performance measures or measurement systems. This study aims at integrating the consideration of essential factors anddimensions of R&D performance analysis to developed selection processes of R&D measures, which have been applied in real-world organizations. The earlier models for corporate performance measurement that can be found in the literature, are to some extent adaptable also to the development of measurement systemsand selecting the measures in R&D activities. However, it is necessary to emphasize the special aspects related to the measurement of R&D performance in a way that make the development of new approaches for especially R&D performance measure selection necessary: First, the special characteristics of R&D - such as the long time lag between the inputs and outcomes, as well as the overall complexity and difficult coordination of activities - influence the R&D performance analysis problems, such as the need for more systematic, objective, balanced and multi-dimensional approaches for R&D measure selection, as well as the incompatibility of R&D measurement systems to other corporate measurement systems and vice versa. Secondly, the above-mentioned characteristics and challenges bring forth the significance of the influencing factors and dimensions that need to be recognized in order to derive the selection criteria for measures and choose the right R&D metrics, which is the most crucial step in the measurement system development process. The main purpose of this study is to support the management and control of the research and development activities of organizations by increasing the understanding of R&D performance analysis, clarifying the main factors related to the selection of R&D measures and by providing novel types of approaches and methods for systematizing the whole strategy- and business-based selection and development process of R&D indicators.The final aim of the research is to support the management in their decision making of R&D with suitable, systematically chosen measures or evaluation methods of R&D performance. Thus, the emphasis in most sub-areas of the present research has been on the promotion of the selection and development process of R&D indicators with the help of the different tools and decision support systems, i.e. the research has normative features through providing guidelines by novel types of approaches. The gathering of data and conducting case studies in metal and electronic industry companies, in the information and communications technology (ICT) sector, and in non-profit organizations helped us to formulate a comprehensive picture of the main challenges of R&D performance analysis in different organizations, which is essential, as recognition of the most importantproblem areas is a very crucial element in the constructive research approach utilized in this study. Multiple practical benefits regarding the defined problemareas could be found in the various constructed approaches presented in this dissertation: 1) the selection of R&D measures became more systematic when compared to the empirical analysis, as it was common that there were no systematic approaches utilized in the studied organizations earlier; 2) the evaluation methods or measures of R&D chosen with the help of the developed approaches can be more directly utilized in the decision-making, because of the thorough consideration of the purpose of measurement, as well as other dimensions of measurement; 3) more balance to the set of R&D measures was desired and gained throughthe holistic approaches to the selection processes; and 4) more objectivity wasgained through organizing the selection processes, as the earlier systems were considered subjective in many organizations. Scientifically, this dissertation aims to make a contribution to the present body of knowledge of R&D performance analysis by facilitating dealing with the versatility and challenges of R&D performance analysis, as well as the factors and dimensions influencing the selection of R&D performance measures, and by integrating these aspects to the developed novel types of approaches, methods and tools in the selection processes of R&D measures, applied in real-world organizations. In the whole research, facilitation of dealing with the versatility and challenges in R&D performance analysis, as well as the factors and dimensions influencing the R&D performance measure selection are strongly integrated with the constructed approaches. Thus, the research meets the above-mentioned purposes and objectives of the dissertation from the scientific as well as from the practical point of view.

Secure many-to-one communications in wireless sensor networks

Wireless Sensor Networks (WSN) are formed by nodes with limited computational and power resources. WSNs are finding an increasing number of applications, both civilian and military, most of which require security for the sensed data being collected by the base station from remote sensor nodes. In addition, when many sensor nodes transmit to the base station, the implosion problem arises. Providing security measures and implosion-resistance in a resource-limited environment is a real challenge. This article reviews the aggregation strategies proposed in the literature to handle the bandwidth and security problems related to many-to-one transmission in WSNs. Recent contributions to secure lossless many-to-one communication developed by the authors in the context of several Spanish-funded projects are surveyed. Ongoing work on the secure lossy many-to-one communication is also sketched.

Assessment of inflammatory Bowel Disease patient's needs and problems from a nursing perspective

BACKGROUND: In this study, we aimed at assessing Inflammatory Bowel Disease patients' needs and current nursing practice to investigate to what extent consensus statements (European Crohn's and Colitis Organization) on the nursing roles in caring for patients with IBD concur with local practice. METHODS: We used a mixed-method convergent design to combine quantitative data prospectively collected in the Swiss IBD cohort study and qualitative data from structured interviews with IBD healthcare experts. Symptoms, quality of life, and anxiety and depression scores were retrieved from physician charts and patient self-reported questionnaires. Descriptive analyses were performed based on quantitative and qualitative data. RESULTS: 230 patients of a single center were included, 60% of patients were males, and median age was 40 (range 18-85). The prevalence of abdominal pain was 42%. Self-reported data were obtained from 75 out of 230 patients. General health was perceived significantly lower compared with the general population (p < 0.001). Prevalence of tiredness was 73%; sleep problems, 78%; issues related to work, 20%; sexual constraints, 35%; diarrhea, 67%; being afraid of not finding a bathroom, 42%; depression, 11%; and anxiety symptoms, 23%. According to experts' interviews, the consensus statements are found mostly relevant with many recommendations that are not yet realized in clinical practice. CONCLUSION: Identified prevalence may help clinicians in detecting patients at risk and improve patient management. © 2015 S. Karger AG, Basel.

Agency problems with non-smooth decision profiles: the case of monopoly under product quality

A method for dealing with monotonicity constraints in optimal control problems is used to generalize some results in the context of monopoly theory, also extending the generalization to a large family of principal-agent programs. Our main conclusion is that many results on diverse economic topics, achieved under assumptions of continuity and piecewise differentiability in connection with the endogenous variables of the problem, still remain valid after replacing such assumptions by two minimal requirements.

Go-to-market strategy with pharmacies

The purpose of the research is to develop a go-to-market strategy with pharmacies. As it was agreed with the client of the study, Reckitt Benckiser, the focus is solely on non-prescription products. Therefore, prescription medicines are not considered in the study. The main objective of the research is to clarify consumer and pharmacy personnel behavior concerning non-prescription products. These issues are observed with surveys, which are provided to consumers and pharmacy personnel. The go-to-market strategy is based on the survey results and is comprised by utilizing the marketing-mix model. Legislation and the present state & trends are additional minor research problems of the study. The results of the research provide many descriptive insights about consumer and pharmacy personnel behavior. It is concluded that the consumers’ level of involvement with non-prescription products is low and the type of behavior is habitual. It is also demonstrated that several decision-making criteria are very different among different age groups and genders. Concerning pharmacy personnel, the factors that they base their product recommendations are revealed. In addition, the sources of medicine information for both consumers and pharmacy personnel are found out.