Desenvolvimento de conjunto membrana-eletrodos para célula a combustível de metanol direto passiva

Direct methanol fuel cells (DMFCs) without external pumps or other ancillary devices for fuel and oxidant supply are known as passive DMFCs and are potential candidates to replace lithium-ion batteries in powering portable electronic devices. This paper presents the results obtained from a membrane electrode assembly (MEA) specifically designed for passive DMFCs. Appropriated electrocatalysts were prepared and the effect of their loadings was investigated. Two types of gas diffusion layers (GDL) were also tested. The influence of the methanol concentration was analyzed in each case. The best MEA performance presented a maximum power density of 11.94 mW cm-2.

Pilhas de combustíveis microbianas utilizadas na produção de eletricidade a partir de rejeitos orgânicos: uma perspectiva de futuro

In this review is presented an innovative technology for use of animal and vegetable waste with high pollution levels in microbial fuel cell (MFC) as an alternative to waste remediation and simultaneously producing electricity and fertilizer for agriculture. A brief history of MFC, the studies about the electron transfer mechanisms, discussion of the biological nanowires in bacteria and the use of chemical mediators or carriers of electrons are explained. The factors influencing the performance of MFCs, the application in waste and sewage treatment and power generation are also discussed.

Desenvolvimento de processo de produção de conjuntos eletrodo-membrana-eletrodo para células a combustível baseadas no uso de membrana polimérica condutora de prótons (PEMFC) por impressão a tela

Proton exchange membrane fuel cell (PEMFC) requires membrane electrode assemblies (MEA) to generate electrical energy from hydrogen and oxygen. In this study a MEA production process by sieve printing and an ink composition were developed to produce catalyst layers of MEAs. The deposition of the exact catalyst content was possible on cathodes and anodes with only one print step. The optimal ink developed shown viscosity of 2.75 Pa s, density 1.27 g cm-3, total solid content of 33.76 % and tack of 92 U.T. The electrodes prepared in only one printing step showed higher performance than those prepared in several steps.

Desenvolvimento de tecnologia para confecção de eletrodos e conjuntos eletrodo-membrana-eletrodo (MEA) por impressão à tela para aplicação em módulos de potência de células PEMFC

Significant functions in the Proton Exchange Membrane Fuel Cells (PEMFCs) rely on Gas Diffusion Layers (GDLs), such as control the water balance in the membrane electrode assembly (MEA), allow suitable gas permeability and porosity, etc. Aware of the GDL importance in the cell performance and its great demand in scale-up projects, the fuel cell research group at Instituto de Pesquisas Energéticas e Nucleares (IPEN) has developed a Sieve Printing method (innovative in Brazil) as a strategic solution for producing GDL and electrodes used in high power PEMFC stacks. The method has shown to be adequate to fabricate low cost electrodes, GDLs of different dimensions and to produce any amount of MEAs for power stacks.

Parallel-Operating Three-Phase Voltage Source Inverters – Circulating CurrentModeling, Analysis and Mitigation

The maximum realizable power throughput of power electronic converters may be limited or constrained by technical or economical considerations. One solution to this problemis to connect several power converter units in parallel. The parallel connection can be used to increase the current carrying capacity of the overall system beyond the ratings of individual power converter units. Thus, it is possible to use several lower-power converter units, produced in large quantities, as building blocks to construct high-power converters in a modular manner. High-power converters realized by using parallel connection are needed for example in multimegawatt wind power generation systems. Parallel connection of power converter units is also required in emerging applications such as photovoltaic and fuel cell power conversion. The parallel operation of power converter units is not, however, problem free. This is because parallel-operating units are subject to overcurrent stresses, which are caused by unequal load current sharing or currents that flow between the units. Commonly, the term ’circulatingcurrent’ is used to describe both the unequal load current sharing and the currents flowing between the units. Circulating currents, again, are caused by component tolerances and asynchronous operation of the parallel units. Parallel-operating units are also subject to stresses caused by unequal thermal stress distribution. Both of these problemscan, nevertheless, be handled with a proper circulating current control. To design an effective circulating current control system, we need information about circulating current dynamics. The dynamics of the circulating currents can be investigated by developing appropriate mathematical models. In this dissertation, circulating current models aredeveloped for two different types of parallel two-level three-phase inverter configurations. Themodels, which are developed for an arbitrary number of parallel units, provide a framework for analyzing circulating current generation mechanisms and developing circulating current control systems. In addition to developing circulating current models, modulation of parallel inverters is considered. It is illustrated that depending on the parallel inverter configuration and the modulation method applied, common-mode circulating currents may be excited as a consequence of the differential-mode circulating current control. To prevent the common-mode circulating currents that are caused by the modulation, a dual modulator method is introduced. The dual modulator basically consists of two independently operating modulators, the outputs of which eventually constitute the switching commands of the inverter. The two independently operating modulators are referred to as primary and secondary modulators. In its intended usage, the same voltage vector is fed to the primary modulators of each parallel unit, and the inputs of the secondary modulators are obtained from the circulating current controllers. To ensure that voltage commands obtained from the circulating current controllers are realizable, it must be guaranteed that the inverter is not driven into saturation by the primary modulator. The inverter saturation can be prevented by limiting the inputs of the primary and secondary modulators. Because of this, also a limitation algorithm is proposed. The operation of both the proposed dual modulator and the limitation algorithm is verified experimentally.

Vertailu kahden erityyppisen virtasyötetyn hakkurin soveltuvuudesta polttokennokäyttöihin

Concerns about condition of the environment and rising fossil fuel prices have accelerated the research of finding new cheap and environmental friendly energy source. Fuel cells are one of the most promising green technologies, especially in the field of distributed energy generation, backup power systems, transportation and mobile power generation. In this bachelor’s thesis use of fuel cells is studied, especially from the DC-DC converter point of view. This bachelor’s thesis concentrates on study of two different DC-DC converters. The aim of this thesis is to study design and steering methods for proposed converters. The ultimate aim of this thesis is to determine which one of proposed converters is most suitable for fuel cell applications.

Diskreettiaikainen liukuvan moodin säätö kiinteäoksidipolttokennon DC-tasonnostossa

Huoli ympäristön tilasta ja fossiilisten polttoaineiden hinnan nousu ovat vauhdittaneet tutkimusta uusien energialähteiden löytämiseksi. Polttokennot ovat yksi lupaavimmista tekniikoista etenkin hajautetun energiantuotannon, varavoimalaitosten sekä liikennevälineiden alueella. Polttokenno on tehonlähteenä kuitenkin hyvin epäideaalinen, ja se asettaa tehoelektroniikalle lukuisia erityisvaatimuksia. Polttokennon kytkeminen sähköverkkoon on tavallisesti toteutettu käyttämällä galvaanisesti erottavaa DC/DC hakkuria sekä vaihtosuuntaajaa sarjassa. Polttokennon kulumisen estämiseksi tehoelektroniikalta vaaditaan tarkkaa polttokennon lähtövirran hallintaa. Perinteisesti virran hallinta on toteutettu säätämällä hakkurin tulovirtaa PI (Proportional and Integral) tai PID (Proportional, Integral and Derivative) -säätimellä. Hakkurin epälineaarisuudesta johtuen tällainen ratkaisu ei välttämättä toimi kaukana linearisointipisteestä. Lisäksi perinteiset säätimet ovat herkkiä mallinnusvirheille. Tässä diplomityössä on esitetty polttokennon jännitettä nostavan hakkurin tilayhtälökeskiarvoistusmenetelmään perustuva malli, sekä malliin perustuva diskreettiaikainen integroiva liukuvan moodin säätö. Esitetty säätö on luonteeltaan epälineaarinen ja se soveltuu epälineaaristen ja heikosti tunnettujen järjestelmien säätämiseen.

Notes on Emerging Technologies

This dissertation considers the impact of technology foresight in innovation within the context of a technology driven development. The main hypothesis made was that by using different methods of foresight in the industry level significant value could be created. The question was approached through a case study in portable fuel cell technology. The theoretical background of the study draws from Innovation, Product Development, Management of Technology, and Technology Foresight. The connection within the topics is made by analyzing foresight, not in a policy view as often done in Europe, but in a micro-level. Focusing mostly on how a technology driven development scenario could be analyzed. The study is based on a bibliometric, extrapolation and patent analysis within the context of a case study. In addition, a large two-year Delphi study was conducted. The study was finalized with a scenario work on the future possibilities of the case study technology. Original publications also consider several methodological issues. In the context of the case study, the study questions the practicality of establishing a portable fuel cell technology in Finland showing several impractical assumptions has been made. In a more conceptual level, the study makes notions on two underlying factors: policy-push technologies and growth of data. Policy-push questions in which level a policy effort towards a single technology is practical. The European foresight effort is more directed towards policy decisions in contrast to US foresight, which is to some extent corporate driven. Although the policy-based foresight has produced significant results in the European context, policy led efforts towards a single technology are challenging. Growth of data argues on the challenges produced by the large-scale application of quantitative measures of foresight. Bibliometric studies and trend extrapolations have been taken advantage of the increasing number of databases made available, and used these as the basis for forecasts. However, the relationship with actual development and quantitative evidence is still unproven.

Performance and scalability of isolated DC-DC converter topologies in low voltage, high current applications

Fuel cells are a promising alternative for clean and efficient energy production. A fuel cell is probably the most demanding of all distributed generation power sources. It resembles a solar cell in many ways, but sets strict limits to current ripple, common mode voltages and load variations. The typically low output voltage from the fuel cell stack needs to be boosted to a higher voltage level for grid interfacing. Due to the high electrical efficiency of the fuel cell, there is a need for high efficiency power converters, and in the case of low voltage, high current and galvanic isolation, the implementation of such converters is not a trivial task. This thesis presents galvanically isolated DC-DC converter topologies that have favorable characteristics for fuel cell usage and reviews the topologies from the viewpoint of electrical efficiency and cost efficiency. The focus is on evaluating the design issues when considering a single converter module having large current stresses. The dominating loss mechanism in low voltage, high current applications is conduction losses. In the case of MOSFETs, the conduction losses can be efficiently reduced by paralleling, but in the case of diodes, the effectiveness of paralleling depends strongly on the semiconductor material, diode parameters and output configuration. The transformer winding losses can be a major source of losses if the windings are not optimized according to the topology and the operating conditions. Transformer prototyping can be expensive and time consuming, and thus it is preferable to utilize various calculation methods during the design process in order to evaluate the performance of the transformer. This thesis reviews calculation methods for solid wire, litz wire and copper foil winding losses, and in order to evaluate the applicability of the methods, the calculations are compared against measurements and FEM simulations. By selecting a proper calculation method for each winding type, the winding losses can be predicted quite accurately before actually constructing the transformer. The transformer leakage inductance, the amount of which can also be calculated with reasonable accuracy, has a significant impact on the semiconductor switching losses. Therefore, the leakage inductance effects should also be taken into account when considering the overall efficiency of the converter. It is demonstrated in this thesis that although there are some distinctive differences in the loss distributions between the converter topologies, the differences in the overall efficiency can remain within a range of a few percentage points. However, the optimization effort required in order to achieve the high efficiencies is quite different in each topology. In the presence of practical constraints such as manufacturing complexity or cost, the question of topology selection can become crucial.

Lujien hitsattavien terästen käyttäytyminen -60 °C:ssa

Opinnäytetyö on osa Arctic Materials Technologies Development -projektia, jonka tavoitteena on kehittää perusteita arktisten alueiden sovelluksiin suunnittelun ja valmistuksen kannalta. Arktisella alueella sijaitsee useita potentiaalisia öljy- ja maakaasuesiintymiä, joiden hyödyn-täminen tulee vuosi vuodelta kannattavammaksi ilmaston lämpenemisestä johtuvan merijään heikkenemisen vuoksi. Alin suunnittelulämpötila arktisilla alueilla on -60 °C, mikä aiheuttaa haasteita sekä materiaalinvalinnalle että hitsaukselle. Ferriittisillä teräksillä esiintyy lämpötilasta riippuvaa sitkeyden vaihtelua, jota kutsutaan transi-tiokäyttäytymiseksi. Lämpötilan laskiessa teräksen iskusitkeys sekä murtumissitkeys laske-vat. Arktisissa sovelluskohteissa käytetään yleisesti niukkaseosteisia, mikroseostettuja hie-noraeteräksiä, joille on ominaista erinomaiset sitkeys-, lujuus- sekä hitsattavuusominaisuudet vaativissakin olosuhteissa. Lujat termomekaanisesti valssatut ja nuorrutetut hienoraeteräkset kattavat myötölujuusluokat 355…700 MPa. Tutkimuksissa on saatu vaihtelevia tuloksia ma-teriaalien isku- ja murtumissitkeydestä -60 °C:ssa. Erityisesti sitkeysominaisuudet hitsiaineen ja muutosvyöhykkeen alueiden välillä ovat vaihtelevia. Pienemmällä lämmöntuonnilla ja seostetuilla lisäaineilla saavutetaan kuitenkin pääsääntöisesti parempia sitkeysarvoja. Asiku-laarinen ferriitti sekä alabainiitti ovat toivottavia mikrorakenteita liitoksessa, niiden pienen raekoon johdosta.

Kaksisuuntaisen DC/DC-hakkurin virtasäätö polttokennosovelluksessa

Ilmastonmuutos ja fossiilisten polttoaineiden ehtyminen ovat edesauttaneet uusiutuvien energialähteiden tutkimusta huomattavasti. Lisäksi alati kasvava sähköenergian tarve lisää hajautetun sähköntuotannon ja vaihtoehtoisten energialähteiden kiinnostavuutta. Yleisimpiä hajautetun sähköntuotannon energialähteitä ovat tuulivoima, aurinkovoima ja uutena tulokkaana polttokennot. Polttokennon kytkeminen sähköverkkoon vaatii tehoelektroniikkaa, ja yleensä yksinkertaisessa polttokennosovelluksessa polttokenno kytketään galvaanisesti erottavan yksisuuntaisen DC/DC-hakkurin ja vaihtosuuntaajan kanssa sarjaan. Polttokennon rinnalla voidaan käyttää akkua tasaamaan polttokennon syöttämää jännitettä, jolloin akun ja polttokennon väliin tarvitaan kaksisuuntainen DC/DC-hakkuri, joka pystyy siirtämään energiaa molempiin suuntiin. Tässä diplomityössä on esitetty kaksisuuntaisen DC/DC-hakkurin tilayhtälökeskiarvoistusmenetelmään perustuva malli sekä mallin perusteella toteutettu virtasäätö. Tutkittava hakkuritopologia on kokosilta-tyyppinen boost-hakkuri, ja säätömenetelmä keskiarvovirtasäätö. Työn tuloksena syntyi tilayhtälömalli kaksisuuntaiselle FB boost -hakkurille sekä sen tulokelan virran säätämiseen soveltuva säädin. Säädin toimii normaalitilanteissa hyvin, mutta erikoistilanteissa, kuten hakkurin tulojännitteen äkillisessä muutostilanteessa, vaadittaisiin tehokkaampi säädin, jolla saavutettaisiin nopeampi nousuaika ilman ylitystä ja oskillointia.

Electromagnetic and thermal design of a multilevel converter with high power density and reliability

Electric energy demand has been growing constantly as the global population increases. To avoid electric energy shortage, renewable energy sources and energy conservation are emphasized all over the world. The role of power electronics in energy saving and development of renewable energy systems is significant. Power electronics is applied in wind, solar, fuel cell, and micro turbine energy systems for the energy conversion and control. The use of power electronics introduces an energy saving potential in such applications as motors, lighting, home appliances, and consumer electronics. Despite the advantages of power converters, their penetration into the market requires that they have a set of characteristics such as high reliability and power density, cost effectiveness, and low weight, which are dictated by the emerging applications. In association with the increasing requirements, the design of the power converter is becoming more complicated, and thus, a multidisciplinary approach to the modelling of the converter is required. In this doctoral dissertation, methods and models are developed for the design of a multilevel power converter and the analysis of the related electromagnetic, thermal, and reliability issues. The focus is on the design of the main circuit. The electromagnetic model of the laminated busbar system and the IGBT modules is established with the aim of minimizing the stray inductance of the commutation loops that degrade the converter power capability. The circular busbar system is proposed to achieve equal current sharing among parallel-connected devices and implemented in the non-destructive test set-up. In addition to the electromagnetic model, a thermal model of the laminated busbar system is developed based on a lumped parameter thermal model. The temperature and temperature-dependent power losses of the busbars are estimated by the proposed algorithm. The Joule losses produced by non-sinusoidal currents flowing through the busbars in the converter are estimated taking into account the skin and proximity effects, which have a strong influence on the AC resistance of the busbars. The lifetime estimation algorithm was implemented to investigate the influence of the cooling solution on the reliability of the IGBT modules. As efficient cooling solutions have a low thermal inertia, they cause excessive temperature cycling of the IGBTs. Thus, a reliability analysis is required when selecting the cooling solutions for a particular application. The control of the cooling solution based on the use of a heat flux sensor is proposed to reduce the amplitude of the temperature cycles. The developed methods and models are verified experimentally by a laboratory prototype.

Développement du chant et profil d'amusie congénitale chez l'enfant

La musique est universelle et le chant est le moyen d’expression musicale le plus accessible à tous. Les enfants chantent spontanément entre un an et un an et demi (Ostwald, 1973). Pourtant, le développement de cette habileté est très peu étudié en neuropsychologie et ce, malgré le fait qu’elle représente une immense source d’informations sur le traitement de la musique par le cerveau. Les études proposées ici visaient à mieux comprendre le développement normal et pathologique des fonctions perceptives et vocales. Dans un premier temps, une étude sur le chant normal chez les enfants de 6 à 11 ans est présentée. Le développement du chant de 79 enfants d’âge scolaire y est analysé de manière systématique et objective. Cette étude se penche plus particulièrement sur l’influence de l’âge ainsi que d’autres facteurs (le genre, la perception musicale, la présence de paroles et la présence d’un accompagnement vocal) sur la qualité du chant. Les jeunes participants ont chanté une chanson familière dans différentes conditions, soit avec et sans paroles, après un modèle ainsi qu’à l’unisson avec ce dernier. Suite à l’analyse acoustique des performances, différentes variables mélodiques et rythmiques telles que le nombre d’erreurs d’intervalles, le nombre d’erreurs de contours, la taille des déviations d’intervalles, le nombre d’erreurs rythmiques, la taille des déviations temporelles et le tempo, ont été calculés. Les résultats montrent que certaines habiletés de base liées au chant se développent toujours après 6 ans. Toutefois, le rythme est maîtrisé plus tôt, et les enfants d’âges scolaires réussissent parfois mieux que les adultes sur le plan rythmique. De plus, il est plus difficile pour les enfants de chanter avec des ii paroles que sur une syllabe et chanter à l’unisson représente un défi plus grand que chanter après un modèle. Par ailleurs, le nombre d’erreurs de contours, d’intervalles et de rythme, de même que la taille des erreurs rythmiques, sont liés à nos mesures de perception musicale. La seconde étude présente le premier cas documenté d’amusie congénitale chez l’enfant. Elle implique l’analyse de la perception musicale et du chant d’une fillette de 10 ans nous ayant été référée par son directeur de chorale. De sévères déficits ont été relevés chez elle et un diagnostic d’amusie congénitale fut posé. En effet, ses résultats aux tests visant à évaluer sa perception musicale indiquent d’importantes difficultés tant sur le plan de la discrimination des différences mélodiques et rythmiques, qu’au niveau de la mémoire des mélodies. La fillette présente des lacunes claires quant à la perception des fines différences de hauteurs. L’analyse des réponses cérébrales en potentiels évoqués suggère que l’enfant souffre de déficits situés tôt au cours des processus de traitement auditif, tel que démontré par l’absence de négativité de discordance (MMN). Le chant de la jeune fille est lui aussi déficitaire, particulièrement en ce qui concerne le nombre d’erreurs d’intervalles et leurs tailles. En conclusion, nos études montrent que les aptitudes pour le chant sont toujours en développement au cours des premières années de scolarisation. Ce développement peut être entravé par la présence d’un déficit lié spécifiquement à la perception musicale. Pour la première fois, l’amusie congénitale, sera décrite chez l’enfant.

Concurrent Smalltalk on the Message-Driven Processor

Concurrent Smalltalk is the primary language used for programming the J- Machine, a MIMD message-passing computer containing thousands of 36-bit processors connected by a very low latency network. This thesis describes in detail Concurrent Smalltalk and its implementation on the J-Machine, including the Optimist II global optimizing compiler and Cosmos fine-grain parallel operating system. Quantitative and qualitative results are presented.

La tecnología del hidrógeno, una oportunidad estratégica para la perdurabilidad del sector energético en Colombia

El incremento de la actividad humana en el último siglo y el desarrollo de tecnologías ligadas con el petróleo como vector energético, han generado efectos medioambientales adversos que aunados con las limitadas reservas mundiales de crudo y su estrecha relación con el crecimiento económico mundial ha generado presiones economías, políticas y sociales en todos los países. Esta situación ha dinamizado la investigación y desarrollo de nuevas tecnologías basadas en el hidrogeno como un nuevo vector energético tecnológicamente compatible que permita la portabilidad de energía con el menor impacto ambiental y económico a la luz de la prospectiva de consumo y la perdurabilidad energética. Este trabajo identifica las experiencias más relevantes respecto a la tecnología del hidrogeno a nivel mundial con el fin de consolidar un plan estratégico para la incorporación del hidrógeno como vector energético al portafolio productivo colombiano mediante la aplicación de un modelo que permite el análisis del nivel de integración de los sectores educativo, empresarial y gubernamental, teniendo como base los resultados del análisis estructural y análisis de actores.