Vibration of a high-altitude tethered balloon with application to climate engineering

A balloon tethered at an altitude of 20 km could deliver a particulate cloud leading to global cooling. Tethering a balloon at this altitude poses significant problems with respect to vibration and stability, especially in regions of high wind. No-one has ever proposed, yet alone launched, a balloon at an altitude of 20 km tethered to the ground. Owing to wind, the tether needs to be 23 km in length and is to be fixed to a ship at sea or on land in equatorial regions. Whilst the balloon at 20 km is subject to relatively modest wind conditions, at jet stream altitudes (10km) the tether will experience much higher wind loadings, not only because of the high wind speeds of up to 300 km / hr but also because of the high air density. A tether of circular cross section in these high winds will be subject to horizontal and downward drag forces that would bring the aerostat down. For this reason it is advantageous to consider a self-aligning tether of an aerodynamic cross section whereby it is possible to reduce the drag substantially. One disadvantage of a non-circular tether is the possibility of flutter and galloping instabilities. It is reasonably straightforward to model these phenomena for short lengths of aerofoil, but the situation becomes more complex for a 20 km tensioned tether with large deflection and curvature, variable wind speed, variable air density and variable tension. Analysis using models of infinite length are used to establish the stability at a local scale where the tension, aerodynamic and geometric properties are considered constant. Dispersion curve analysis is useful here. But for dynamics on a long-wavelength scale (several km) then a full non-linear analysis is required. This non-linear model can be used to establish the local values of tension appropriate for the dispersion analysis. This keynote presentation will give some insight into these issues.

High-density remote plasma sputtering of high-dielectric-constant amorphous hafnium oxide films

Hafnium oxide (HfOx) is a high dielectric constant (k) oxide which has been identified as being suitable for use as the gate dielectric in thin film transistors (TFTs). Amorphous materials are preferred for a gate dielectric, but it has been an ongoing challenge to produce amorphous HfOx while maintaining a high dielectric constant. A technique called high target utilization sputtering (HiTUS) is demonstrated to be capable of depositing high-k amorphous HfOx thin films at room temperature. The plasma is generated in a remote chamber, allowing higher rate deposition of films with minimal ion damage. Compared to a conventional sputtering system, the HiTUS technique allows finer control of the thin film microstructure. Using a conventional reactive rf magnetron sputtering technique, monoclinic nanocrystalline HfOx thin films have been deposited at a rate of ∼1.6nmmin-1 at room temperature, with a resistivity of 1013Ωcm, a breakdown strength of 3.5MVcm-1 and a dielectric constant of ∼18.2. By comparison, using the HiTUS process, amorphous HfOx (x=2.1) thin films which appear to have a cubic-like short-range order have been deposited at a high deposition rate of ∼25nmmin-1 with a high resistivity of 1014Ωcm, a breakdown strength of 3MVcm-1 and a high dielectric constant of ∼30. Two key conditions must be satisfied in the HiTUS system for high-k HfOx to be produced. Firstly, the correct oxygen flow rate is required for a given sputtering rate from the metallic target. Secondly, there must be an absence of energetic oxygen ion bombardment to maintain an amorphous microstructure and a high flux of medium energy species emitted from the metallic sputtering target to induce a cubic-like short range order. This HfOx is very attractive as a dielectric material for large-area electronic applications on flexible substrates. A remote plasma sputtering process (high target utilization sputtering, HiTUS) has been used to deposit amorphous hafnium oxide with a very high dielectric constant (∼30). X-ray diffraction shows that this material has a microstructure in which the atoms have a cubic-like short-range order, whereas radio frequency (rf) magnetron sputtering produced a monoclinic polycrystalline microstructure. This is correlated to the difference in the energetics of remote plasma and rf magnetron sputtering processes. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Collective motion of self-propelled particles: Stabilizing symmetric formations on closed curves

We provide feedback control laws to stabilize formations of multiple, unit speed particles on smooth, convex, and closed curves with definite curvature. As in previous work we exploit an analogy with coupled phase oscillators to provide controls which isolate symmetric particle formations that are invariant to rigid translation of all the particles. In this work, we do not require all particles to be able to communicate; rather we assume that inter-particle communication is limited and can be modeled by a fixed, connected, and undirected graph. Because of their unique spectral properties, the Laplacian matrices of circulant graphs play a key role. The methodology is demonstrated using a superellipse, which is a type of curve that includes circles, ellipses, and rounded rectangles. These results can be used in applications involving multiple autonomous vehicles that travel at constant speed around fixed beacons. ©2006 IEEE.

Computational analysis of liquid crystalline elastomer membranes: Changing Gaussian curvature without stretch energy

Liquid crystalline elastomers (LCEs) can undergo extremely large reversible shape changes when exposed to external stimuli, such as mechanical deformations, heating or illumination. The deformation of LCEs result from a combination of directional reorientation of the nematic director and entropic elasticity. In this paper, we study the energetics of initially flat, thin LCE membranes by stress driven reorientation of the nematic director. The energy functional used in the variational formulation includes contributions depending on the deformation gradient and the second gradient of the deformation. The deformation gradient models the in-plane stretching of the membrane. The second gradient regularises the non-convex membrane energy functional so that infinitely fine in-plane microstructures and infinitely fine out-of-plane membrane wrinkling are penalised. For a specific example, our computational results show that a non-developable surface can be generated from an initially flat sheet at cost of only energy terms resulting from the second gradients. That is, Gaussian curvature can be generated in LCE membranes without the cost of stretch energy in contrast to conventional materials. © 2013 Elsevier Ltd. All rights reserved.

Switch mode constant current LED Driver with high efficiency, high precision and wide dimming ratio

A high efficiency hard switching constant current LED driver is presented with high overall efficiency, high current precision, high LED efficacy, flicker-free and wide constant current dimming ratio. The high stable lighting source provides the best solution for office light, reading light and LCD backlight. © 2013 IEEE.

Vibration of pressurised, elastic, spherical shells

Balloons are one example of pressurised, elastic, spherical shells. Whilst analytical solutions exist for the vibration of pressurised spheres, these models only incorporate constant tension in the membrane. For elastic shells, changes in curvature will result in restoring forces that are proportional to the elasticity in the membrane; hence the assumption of constant tension is not valid. This paper describes an analytical solution for the natural frequencies of an elastic spherical shell subject to internal pressure. When the membrane tension is set to zero, the results are shown to converge to the analytical solution for a spherical shell, and when the skin elasticity is neglected, the results converge to the constant-tension solution. This analytical solution is used to predict the natural frequencies of a small balloon, based on a value for the elastic modulus that is determined using biaxial tensile testing. These predictions are compared to experimental measurements of balloon vibrations using impact hammer testing, and good agreement is seen.

Comparison of moment-curvature models for fiber-reinforced polymer plate-end debonding studies using global energy balance approach

This paper compares a number of different moment-curvature models for cracked concrete sections that contain both steel and external fiber-reinforced polymer (FRP) reinforcement. The question of whether to use a whole-section analysis or one that considers the FRP separately is discussed. Five existing and three new models are compared with test data for moment-curvature or load deflection behavior, and five models are compared with test results for plate-end debonding using a global energy balance approach (GEBA). A proposal is made for the use of one of the simplified models. The availability of a simplified model opens the way to the production of design aids so that the GEBA can be made available to practicing engineers through design guides and parametric studies. Copyright © 2014, American Concrete Institute.

Second-order rate region of constant-composition codes for the multiple-access channel

This paper presents an achievable second-order rate region for the discrete memoryless multiple-access channel. The result is obtained using a random-coding ensemble in which each user's codebook contains codewords of a fixed composition. It is shown that this ensemble performs at least as well as i.i.d. random coding in terms of second-order asymptotics, and an example is given where a strict improvement is observed. © 2013 IEEE.

Local strain rate and curvature dependences of scalar dissipation rate transport in turbulent premixed flames: A direct numerical simulation analysis

The statistical behaviours of the instantaneous scalar dissipation rate Nc of reaction progress variable c in turbulent premixed flames have been analysed based on three-dimensional direct numerical simulation data of freely propagating statistically planar flame and V-flame configurations with different turbulent Reynolds number Ret. The statistical behaviours of N c and different terms of its transport equation for planar and V-flames are found to be qualitatively similar. The mean contribution of the density-variation term T1 is positive, whereas the molecular dissipation term (-D2) acts as a leading order sink. The mean contribution of the strain rate term T2 is predominantly negative for the cases considered here. The mean reaction rate contribution T3 is positive (negative) towards the unburned (burned) gas side of the flame, whereas the mean contribution of the diffusivity gradient term (D) assumes negative (positive) values towards the unburned (burned) gas side. The local statistical behaviours of Nc, T1, T2, T 3, (-D2), and f(D) have been analysed in terms of their marginal probability density functions (pdfs) and their joint pdfs with local tangential strain rate aT and curvature km. Detailed physical explanations have been provided for the observed behaviour. © 2014 Y. Gao et al.

Peculiarity of constant photocurrent method for silicon films with mixed amorphous-nanocrystalline structure

The results of conductivity, photoconductivity and constant photocurrent method absorption measurements by DC and AC methods in hydrogenated silicon films with mixed amorphous-nanocrystalline structure are presented. A series of diphasic silicon films was deposited by very high frequency plasma enhanced chemical vapor deposition technique, using different hydrogen dilution ratios of silane. The increase of hydrogen dilution ratio results in five orders of magnitude increase of conductivity and a sharp increase of grain volume fraction. The comparison of the absorption spectra obtained by DC and AC methods showed that they are similar for silicon films with the predominantly amorphous structure and films with high grain volume fraction. However we found a dramatic discrepancy between the absorption spectra obtained by DC and AC constant photocurrent methods in silicon films deposited in the regime of the structure transition from amorphous to nanocrystalline state. AC constant photocurrent method gives higher absorption coefficient than DC constant photocurrent method in the photon energy range of 1.2-1.7 eV. This result indicates the possibility of crystalline grains contribution to absorption spectra measured by AC constant photocurrent method in silicon films with intermediate crystalline grain volume fraction. (c) 2008 Published by Elsevier B.V.

Curvature Correction of FWHM in the X-Ray Rocking Curve of Bent Heteroepitaxial Films

A method for accurate determination of the curvature radius of semiconductor thin films is proposed. The curvature-induced broadening of the x-ray rocking curve (XRC) of a heteroepitaxially grown layer can be determined if the dependence of the full width at half maximum (FWHM) of XRC is measured as a function of the width of incident x-ray beam. It is found that the curvature radii of two GaN films grown on a sapphire wafer are different when they are grown under similar MOCVD conditions but have different values of layer thickness. At the same time, the dislocation-induced broadening of XRC and thus the dislocation density of the epitaxial film can be well calculated after the curvature correction.

Dielectric relaxation and giant dielectric constant of Nb-doped CaCu3Ti4O12 ceramics under dc bias voltage

CaCu3Ti(4-x)Nb(x)O(12) (x = 0, 0.01, 0.08, 0.2) ceramics were fabricated by a conventional solid-state reaction method. The ceramics showed the body-centered cubic structure without any foreign phases and the grain size decreases with Nb doping. Two Debye-type relaxations were observed for the Nb-doped samples at low frequency and high frequency, respectively. The complex electric modulus analysis revealed that the surface layer, grains and grain boundaries contributed to the dielectric constant. The low-frequency dielectric constant relative to the surface layer decreased to a minimum and then increased with the dc bias voltage at 100 Hz, which were well explained in terms of a model containing two metal oxide semiconductors in series, confirming the surface layer in the ceramics. The shift voltage V-B corresponding to the minimal capacitance increased with increase of the composition x. (C) 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A voltage-adjustable three-phase rectifier with constant power flow

An three phase adjustable output voltage rectifier with constant power flow based on waveform gap patching principle is resented. By patching the gapes in the phase currents in parallel way as well as the ripple of the output voltage in series way, it implements the constant power flow from the three-phase line to the DC output without using any line frequency (and its harmonics) energy storage components. Principally, by treating only 22.4% power of the needed power output, this rectifier can supply constant power flow with adjustable output voltages without bring about any harmonic interferences to the power utility and achieve unite power factor.